Braun 7526 User manual

+

7526

Syncro SystemSmart Logic

Type Modèle Modelo

5493

+

5301

5493310_S.1.fm Seite 1 Donnerstag, 12. Mai 2005 2:15 14

Page is loading ...

13

14

15

16

17

18

19

12

Syncro 7526

A

B

Clean &Renew™

11

4

1

2

3

5

6

7

8

9

10

4

No. 7000

7526

+

-

5493310_S.3.fm Seite 1 Donnerstag, 12. Mai 2005 2:16 14

4

English

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic precautions should always be follo-

wed, including the following:

Read all instructions before using this appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water.

Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place, store or charge the appliance where it can fall or be pulled

into a tub or sink. Do not place in or drop into water or other liquid.

4. When not using for a longer period of time, unplug this appliance from the

electrical outlet.

5. Unplug this appliance before cleaning.

6. This appliance is provided with a low voltage adapter. Do not exchange or

manipulate any part of it.

FOR HOUSEHOLD USE

SAVE THESE INSTRUCTIONS

5493310_S.4-38.fm Seite 4 Donnerstag, 12. Mai 2005 2:18 14

5

WARNING

To reduce the risk of burns, ﬁre, electric shock, or injury to persons:

1. Close supervision is necessary when this appliance is used by, on, or near

children.

2. Use this appliance only for its intended use as described in this manual.

Do not use attachments not recommended by the manufacturer.

3. The appliance should never be exposed to temperatures of less than

32 ºF / 0 ºC and more than 105 ºF/+40ºC for longer than a few hours.

Keep the appliance and cord dry at all times. Do not handle with wet hands.

Do not store in a damp environment. To avoid damage do not wind the cord

around the appliance. It is important to check the cord for damage periodi-

cally particularly at each end where the cord enters the plug.

4. Never operate this appliance if it has a damaged cord or plug, if it is not wor-

king properly, if it has been dropped or damaged, or dropped into water.

Return the appliance to a service center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray) products are being

used or where oxygen is being administered.

8. Do not use this appliance with a damaged or broken foil, as serious facial

injuries may occur.

9. Always attach plug to appliance ﬁrst, then to outlet.

To disconnect, turn all controls to «off», then remove plug from outlet.

5493310_S.4-38.fm Seite 5 Donnerstag, 12. Mai 2005 2:18 14

6

A Shaver

Your Braun Syncro is supplied with a Braun

Clean&Renew™ (please see section B).

SmartLogic

The «SmartLogic» electronics inside your shaver ana-

lyzes your personal shaving patterns, and then adapts

the battery care and cleaning cycles to ensure optimal

performance.

Technical speciﬁcations:

• Wattage via low voltage cord: 7 W

• Power supply via mains adapter, input voltage:

100-240 V ~ / 50 or 60 Hz (automatic adaptation)

• Shaver input voltage: 12 V

Description

1 Foil protection cap 7 Charging light (green)

2 Shaver foil 8 Low charge light (red)

3 Cutter block 9 Pilot light

4 Foil release button 10 Shaver socket

5 Long hair trimmer 11 Power supply cord set

6 Switch

Charging the shaver

• First char

ging: Using the power supply cord set,

connect the shaver to the mains with the switch in

position «0» and charge it for at least 4 hours (plug

might get warm).

The SmartLogic inside your shaver automatically

monitors the condition of the batteries as well as the

charging/discharging processes and adapts them to

your personal shaving patterns.

• From now on, the SmartLogic inside your shaver will

ensure optimal care of the batteries. If, for instance,

it is your habit to never let the batteries get low, the

SmartLogic will recognize this, look for a pause

when you are likely to not use the shaver and com-

pletely discharge and then recharge your shaver to

recondition the batteries (every six months at the

most, and only when necessary).

• A full charge will give up to 50 minutes of cordless

shaving time depending on your beard growth.

However, the maximum battery capacity will only be

reached after several charging/discharging cycles.

210

7540

5493310_S.4-38.fm Seite 6 Donnerstag, 12. Mai 2005 2:18 14

7

• Best environmental temperature range for charging

is 60°F to 95°F / 15 °C to 35°C.

Indicator lights

The pilot light shows that the shaver is connected to the

mains.

The green charging light shows that the shaver is being

charged. When the rechargeable battery is fully charg-

ed, the charging light ﬂashes or goes off.

If later on, the charging light comes on again, this indi-

cates that the shaver is being recharged to maintain its

full capacity.

The red low-charge light ﬂashes when the battery capa-

city has dropped below 20%, provided the shaver is

switched on. The remaining capacity will then be sufﬁ-

cient for 2 to 3 shaves.

Shaving

Switch positions

0 = Off (switch is locked)

Press and push up the switch to operate the

shaver:

1 = Shaving with the pivoting head

The pivoting cutting system automatically adjusts

to every contour of your face.

2 = Shaving with the pivoting head locked at an angle

(to permit shaving in difﬁcult areas, e.g. under the

nose)

3 = The long hair trimmer is activated (for trimming

sideburns, moustache and beard).

Shaving with the cord

If the rechargeable battery is discharged, you may also

shave with the shaver connected to the mains via the

power supply cord set.

(If the shaver does not run immediately, charge it with

the switch on position «0» for approx. 1 minute.

+

21

2

a

u

t

o

m

a

t

i

c

l

o

c

k

2

1

3

1

5493310_S.4-38.fm Seite 7 Donnerstag, 12. Mai 2005 2:18 14

8

Keeping your shaver in top shape

Automated cleaning

The Braun Clean&Renew™ takes care of all cleaning

and lubrication needs of your shaver. Please refer to the

separate use instructions.

Manual cleaning

For easy cleaning after each shave, switch the shaver

off. Press the release buttons to lift the shaver foil (do

not remove the foil completely). Switch on the shaver

for approx. 5-10 seconds so that the shaved stubbles

can fall out.

For a thorough cleaning (weekly), remove the shaver foil

and tap it out on a ﬂat surface. Using the brush, clean

the cutter block and the inner area of the pivoting head.

About every four weeks, clean the cutter block with

Braun cleaning agents.

If your skin is very dry and you notice a reduced opera-

tion time of the shaver apply a drop of light machine oil

onto the shaver foil.

Replacing the shaving parts

The shaver foil and cutter block are precision parts that,

in time, are subject to wear. Replace your foil and cutter

block every 18 months and get a 25 % better shave.*

(Shaver foil and cutter block: part No. 7000)

(* Overall evaluation from Braun users comparing their

shave with new parts and those used for 18 months.)

Tips for the perfect shave

• It can take 14-21 days for your beard to adjust to

the new shaving system.

• We recommend that you shave befor

e washing,

as the skin tends to be slightly swollen after

washing.

• Hold the shaver at right angles (90°) to the skin.

• Stretch your skin and shave against the direction

of beard growth.

• Replace the shaver foil and cutter block every

18 months, or when the parts are worn, to ensure

optimum shaving performance.

oil

10

5493310_S.4-38.fm Seite 8 Donnerstag, 12. Mai 2005 2:18 14

9

Accessories

Available at your dealer or Braun Service Centres:

Shaver foil and cutter block

(part No. 7000)

Environmental notice

This appliance is provided with a nickel-hydride

batteries. They do not contain any harmful heavy

metals. Nevertheless, in the interest of recycling raw

materials, please do not dispose of this appliance in the

household waste at the end of its useful life. Disposal

can take place at a Braun Service Center or appropriate

collection sites.

Subject to change without notice.

7000

Syncro

7000

5493310_S.4-38.fm Seite 9 Donnerstag, 12. Mai 2005 2:18 14

10

B Clean&Renew™

Braun Clean&Renew™ has been developed to automa-

tically clean and charge your shaver. It also serves as a

storage unit. For peak performance of your shaver,

clean it daily in the Clean&Renew™.

During the automated cleaning process, the shaver is

switched on and off at intervals to obtain best cleaning

results. Since the specially formulated cleaning ﬂuid

also contains a small amount of oil, the cleaning proce-

dure also fulﬁlls the lubrication needs of your shaver.

Important

• Only use the power supply cord set supplied with

the shaver.

• In order to avoid any leakage of the cleaning ﬂuid,

place the appliance on a ﬂat, stable surface. Be

careful not to tip, move suddenly or transport in any

way if a cleaning cartridge is installed.

• Do not place the appliance in a mirror cabinet, nor

store it over radiators, nor place it on polished or

laquered surfaces. Do not expose to direct sunlight.

• The appliance contains highly ﬂammable

liquid. Keep it away from sources of ignition.

No smoking. Keep out of reach of children.

Do not reﬁll cartridge. Use only original Braun reﬁll

cartridge.

• When cleaning the shaver, its protection cap should

be removed.

Description

12 Lift button for cartridge exchange

13 Release button

14 Contact bow

15 Operation mode selector

16 «clean» light: cleaning process indicator

17 «charge» light: charging process indicator

18 «cartridge» light: cartridge replacement indicator

19 Cleaning cartridge

Technical speciﬁcations

• Power consumption:

3 W when cleaning

7 W when charging

• Power supply:

100-240 V ~ / 50 or 60 Hz (automatic adaptation)

• Input voltage: 12 V

5493310_S.4-38.fm Seite 10 Donnerstag, 12. Mai 2005 2:18 14

11

Before using Clean&Renew™

For the ﬁ

rst charge of the shaver, connect the power

supply cord set directly to the shaver, charge it for

4 hours and shave at least once.

Only then can the shaver be cleaned or recharged in the

Clean&Renew™.

If the rechargeable batteries are discharged, select the

combined «clean + charge» program rather than the

«clean» program alone.

Installing the cartridge

Press the lift button (12) to open the housing.

Hold the cartridge down on a ﬂat, stable surface

(e.g. table). Carefully remove the lid from the cartridge.

Slide the cartridge into the base as far as it will go.

Slowly close the housing by pushing it down until it

locks.

Replacing the cartridge

After having pressed the lift button to open the housing,

wait for a few seconds before removing the used car-

tridge.

Before discarding the used cartridge, make sure to

close the openings using the lid of the new cartridge,

since the used cartridge will contain contaminated

cleaning solution.

Operating your Clean&Renew™

• Use the power supply cord set from your shaver and

plug it into the Clean&Renew™ and then into a main

outlet.

Open the contact bow (13) by pressing the release

button (14). After shaving, switch the shaver off and

place it upside down into the Clean&Renew™

(without having released the shaver foil).

• Select the operation mode by toggling with the

mode selector (15):

clean (about 15 min)

clean + charge (about 75 min)

charge (about 60 min)

The corresponding lights will come on.

(With cord shavers, only the «clean» function can be

selected.)

2

1

old

new

7526

a

u

t

o

m

a

t

i

c

l

o

c

k

3

2

1

0

o

n

/

o

ff

c

le

a

n

c

h

a

r

g

e

c

a

r

t

r

i

d

g

e

7526

a

u

t

o

m

a

t

i

c

l

o

c

k

3

2

10

7526

5493310_S.4-38.fm Seite 11 Donnerstag, 12. Mai 2005 2:18 14

12

• Slide down the contact bow to connect the shaver

and to start the selected program.

If no program is selected, the default function

«clean» will be started.

• Do not interrupt a running program, as it leaves

the shaver wet and not ﬁt for use. If interruption is

needed nonetheless, press the release button.

• After a program has ﬁnished, the corresponding light

will go out. Prior to the next shave, press the release

button to release the shaver.

• When the «cartridge» light starts ﬂashing, the re-

maining ﬂuid in the cartridge is sufﬁcient for approxi-

mately 5 more cleaning cycles. After these 5 cycles,

the cleaning performance will be reduced and the

cartridge has to be replaced.

• When the «cartridge» light illuminates constantly, the

cleaning function is locked and a new cartridge has

to be installed.

Only then, the next cleaning cycle can be started.

• A cleaning cartridge should be sufﬁcient for about

30 cleaning cycles. With daily use, the cleaning

cartridge should be replaced approx. every 4 weeks.

• The hygienic cleaning solution cartridge contains

alcohol which, once opened, will naturally evaporate

slowly into the surrounding air. Each cartridge, if not

used daily, should be replaced after approximately

8 weeks.

• Clean the housing from time to time with a damp

cloth, especially the opening where the shaver rests.

Accessories

Available at your dealer or Braun Service Centers:

Reﬁll cartridge

(double pack) CCR 2, (#5331)

Subject to change without notice.

select

clean

char

ge

cartridge

s

e

le

c

t

7526

select

7526

5493310_S.4-38.fm Seite 12 Donnerstag, 12. Mai 2005 2:18 14

13

FOR USA ONLY

2 year limited warranty

(foil and cutterblock excluded)

Braun warrants this Braun appliance (except foil and cutterblock) to be free of

defects in material and workmanship for a period of two years from the date of

original purchase.

If the appliance exhibits such a defect, Braun will, at its option, either repair or

replace it for the consumer without charge, provided the consumer:

1. Returns the appliance, postage paid and insured, indicating the reasons for

returning it to: Shaver Service Department, Braun U.S. Div., The Gillette Co.,

400 Unicorn Park Drive, Woburn,

MA 01801-3376,

or one of its authorized

service centers.

2. Submits proof of date of original purchase.

This warranty does not cover foils, cutterblocks or damage resulting from acci-

dent, misuse, abuse, dirt, water, tampering, unreasonable use, normal wear, ser-

vicing performed or attempted by unauthorized service agencies or failure to

provide reasonable and necessary maintenance, including recharging.

ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE

LIMITED IN DURATION TO 2 YEARS FROM DATE OF ORIGINAL PURCHASE.

IN NO EVENT WILL BRAUN BE RESPONSIBLE FOR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequen-

tial damages, so the above limitation or exclusion may not apply to you.

This warranty gives you speciﬁc legal rights, and you may also have other legal

rights which vary from state to state.

5493310_S.4-38.fm Seite 13 Donnerstag, 12. Mai 2005 2:18 14

14

FOR CANADA ONLY

2 year limited warranty

(foil and cutterblock excluded)

In the event a Braun appliance fails to function within 2 years from date of

purchase, because of defects in material or workmanship, and the consumer

returns the unit to an authorized service center, Braun Canada, will, at its option,

either repair or replace the unit without additional charge to the consumer.

This guarantee does not cover any product, which has been damaged by drop-

ping, tampering, wrong current, servicing performed or attempted by unauthori-

zed service agencies, misuse or abuse,

kinks in the shaver foil as well as the

normal wear of the shearing parts.

Exclusion of Warranties:

The foregoing warranty is the sole warranty offered

by Braun Canada. Braun Canada hereby disclaims any implied warranty of

merchantability or ﬁtness for any particular purpose. In no event will Braun

Canada be responsible for consequential damages resulting from the use of this

product.

5493310_S.4-38.fm Seite 14 Donnerstag, 12. Mai 2005 2:18 14

Page is loading ...

Braun 7526 User manual

This manual is also suitable for

Braun 7526 User manual

in other languages

Related papers

Other documents