Craftsman 320.46123 Owner's manual

Brand: Craftsman

Model: 320.46123

Category: Power tools

Type: Owner's manual

This manual is also suitable for

3282

Operator’s Manual

12 Amp 7 1/4 in. CIRCULAR SAW

Model No. 320.46123

Sears Brands Management Corporation, Hoffman Estates,

IL 60179 U.S.A.

www.craftsman.com

• WARRANTY

• SAFETY

• DESCRIPTION

• ASSEMBLY

• OPERATION

• MAINTENANCE

• ESPAÑOL

ѥWARNING: To reduce the risk of injury,

the user must read and understand the

Operator’s Manual before using this product.

Volts

amperes

hertz

watts

kilowatts

hours

minutes

seconds

no-load speed

Revolutions or reciprocations per minute

Direct current

Alternating current

Class II tool

IP symbol

Read The Operator’s Manual

TABLE OF CONTENTS

Warranty Page 2

Safety Symbols Pages 4-5

Safety Instructions Pages 6-10

Description Pages 11-12

Assembly Pages 13-14

Operation Pages 15-24

Maintenance Page 25

Troubleshooting Page 26

Parts List Page 27

CRAFTSMAN LIMITED WARRANTY

FOR ONE YEAR from the date of sale, this product is warranted against any

defects in material or workmanship.

WITH PROOF OF SALE, a defective product will be replaced free of charge.

For warranty coverage details to obtain free replacement, visit the web

page: www.craftsman.com/warranty

This warranty does not cover the blade or blade wrench, which are

expendable parts that can wear out from normal use within the

warranty period.

This ONE YEAR warranty is void if this product is ever used while providing

commercial services or if rented to another person. For 90 DAY commercial

and rental use terms, see the Craftsman warranty web page.

This warranty gives you specic legal rights, and you may also have other

rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179.

SAVE THESE INSTRUCTIONS!

READ ALL INSTRUCTIONS!

This circular saw has many features for making its use more pleasant and

enjoyable. Safety, performance, and dependability have been given top priority

in the design of this product, making it easy to maintain and operate.

ѥDANGER: People with electronic devices, such as pacemakers, should

consult their physician(s) before using this product. Operation of electrical

equipment in close proximity to a heart pacemaker could cause interference or

failure of the pacemaker.

ѥWARNING: Some dust created by power sanding, sawing, grinding, drilling

and other construction activities contains chemicals known to the state of

California to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other masonry products, and

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemical: work in a well-ventilated

area, and work with approved safety equipment, such as those dust masks that

are specially designed to lter out microscopic particles.

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers.

The safety symbols and the explanations with them deserve your careful

attention and understanding. The symbol warnings do not, by themselves,

eliminate any danger. The instructions and warnings they give are no substitutes

for proper accident prevention measures.

ѥWARNING: Be sure to read and understand all safety instructions in this

manual, including all safety alert symbols such as “DANGER,” ”WARNING,”

and “CAUTION” before using this tool. Failure to follow all instructions listed in

this manual may result in electric shock, fire and/or serious personal injury.

SYMBOL SIGNAL MEANING

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION; may

be used in conjunction with other symbols or pictographs.

ѥDANGER: Indicates a hazardous situation which, if not avoided, will result in

death or serious injury.

ѥWARNING: Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

ѥCAUTION: Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

Damage prevention and information messages

These inform the user of important information and/or instructions that could

lead to equipment or other property damage if they are not followed. Each

message is preceded by the word “NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are

not followed.

ѥWARNING: To ensure safety and reliability, all repairs should be performed

by a qualified service technician.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

min Minutes Time

Alternating Current Type of current

Direct Current Type or a characteristic of current

Rotational speed, at no load

Class II Construction Double-insulated construction

.../mi n Per Minute

Revolutions, strokes, surface speed,

orbits, etc., per minute

Wet Conditions Alert

Do not expose to rain or use in damp

locations.

Read The Operator’s Manual

To reduce the risk of injury

, user must

ad and understand operator’s manual

before using this product.

Eye Protection

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

Safety Alert Precautions that involve your safety.

No-Hands Symbol

Failure to keep your hands away from the

blade will result in serious personal injury.

No-Hands Symbol

Failure to keep your hands away from the

blade will result in serious personal injury.

No-Hands Symbol

Failure to keep your hands away f

rom the

blade will result in serious personal injury.

No-Hands Symbol

Failure to keep your hands away from the

blade will result in serious personal injury.

Hot Surface

To reduce the risk of injury or damage,

avoid contact with any hot surface.

SYMBOL NAME DESIGNATION/EXPLANATION

No-load Speed

WARNING: The operation of any power tools can result in

foreign objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation,

always wear safety goggles or safety glasses with side shield

and a full face shield when needed. We recommend a Wide

Vision Safety Mask for use over eyeglasses or standard safety

glasses with side shields. Always use eye protection which is

marked to comply with ANSI Z87.1.

SAVE THESE INSTRUCTIONS

Some of the llowing symbols may be used on this tool. Please study them and

learn their meaning. Proper interpretation of these symbols will allow you to

operate the tool better and more safely.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

min Minutes Time

Alternating Current Type of current

Direct Current Type or a characteristic of current

Rotational speed, at no load

Class II Construction Double-insulated construction

.../min Per Minute

Revolutions, strokes, surface speed,

orbits, etc., per minute

Wet Conditions Alert

Do not expose to rain or use in damp

locations.

Read The Operator’s Manual

To reduce the risk of injury

, user must

ad and understand operator’s manual

before using this product.

Eye Protection

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

Safety Alert Precautions that involve your safety.

No-Hands Symbol

Failure to keep your hands away from the

blade will result in serious personal injury.

No-Hands Symbol

Failure to keep your hands away from the

blade will result in serious personal injury.

No-Hands Symbol

Failure to keep your hands away f

rom the

blade will result in serious personal injury.

No-Hands Symbol

Failure to keep your hands away from the

blade will result in serious personal injury.

Hot Surface

To reduce the risk of injury or damage,

avoid contact with any hot surface.

SYMBOL NAME DESIGNATION /EXPLANATION

No-load Speed

SAFETY INSTRUCTIONS

GENERAL POWER TOOL SAFETY WARNINGS

ѥWARNING: Read all safety warnings and instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY

• Keep the work area clean and well lit. Cluttered or dark areas

invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks,

which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in

any way. Do not use any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching outlets will reduce risk

of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

• When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is unavoidable, use a

ground-fault circuit interrupter (GFCI) protected power supply. Use of a

GFCI reduces the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and

collection facilities, ensure that these are connected and properly used.

Use of these devices can reduce dust-related hazards.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and more safely

at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source and/or the battery pack

from the power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate

the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories, tool bits, etc. in accordance with

these instructions, taking into account the working conditions and the

work to be performed. Use of the power tool for operations different from

those intended could result in a hazardous situation.

SERVICE

• Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

• Follow instructions in the Maintenance section of this manual. Use of

unauthorized parts or failure to follow Maintenance instructions may create

a risk of shock or injury.

SPECIFIC SAFETY RULES FOR CIRCULAR SAW

Safety instructions for all saws

ѥDANGER: Keep hands away from cutting area and the blade. Keep your

second hand on auxiliary handle or motor housing. If both hands are holding the

saw, they cannot be cut by the blade.

• Do not reach underneath the workpiece. The guard cannot protect you

from the blade below the workpiece.

• Adjust the cutting depth to the thickness of the workpiece. Less than a

full tooth of the blade teeth should be visible below the workpiece.

• Never hold piece being cut in your hands or across your leg. Secure

the workpiece to a stable platform. It is important to support the work

properly to minimize body exposure, blade binding, or loss of control.

• Hold the power tool by the insulated gripping surfaces only when

performing an operation where the cutting tool may contact hidden

wiring or its own cord. Contact with a “live” wire will also make exposed

metal parts of the power tool “live”.

• When ripping, always use a rip fence or straight edge guide. This

improves the accuracy of cut and reduces the chance of blade binding.

• Always use blades with correct size and shape (diamond versus round)

of arbor holes. Blades that do not match the mounting hardware of the saw

will run eccentrically, causing loss of control.

• Never use damaged or incorrect blade washers or bolt. The blade

washers and bolt were specially designed for your saw, for optimum

performance and safety of operation.

Kickback causes and related warnings

Kickback is a sudden reaction to a pinched, bound or misaligned saw

blade, causing an uncontrolled saw to lift up and out of the workpiece

toward the operator.

When the blade is pinched or bound tightly by the kerf closing down, the blade

stalls and the motor reaction drives the unit rapidly back toward the operator.

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge

of the blade can dig into the top surface of the wood causing the blade to climb

out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or

conditions and can be avoided by taking proper precautions as given below.

• Maintain a firm grip with both hands on the saw and position your arms

to resist kickback forces. Position your body to either side of the blade,

but not in line with the blade. Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by the operator if proper

precautions are taken.

• When the blade is binding, or when interrupting a cut for any reason,

release the trigger and hold the saw motionless in the material until

the blade comes to a complete stop. Never attempt to remove the saw

from the work or pull the saw backward while the blade is in motion, or

kickback may occur. Investigate and take corrective actions to eliminate

the cause of blade binding.

• When restarting a saw in the workpiece, center the saw blade in the

kerf and check that saw teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback from the workpiece as the saw

is restarted.

• Support large panels to minimize the risk of blade pinching and

kickback. Large panels tend to sag under their own weight. Supports must

be placed under the panel on both sides, near the line of cut and near the

edge of the panel.

• Do not use dull or damaged blades. Unsharpened or improperly set

blades produce narrow kerf causing excessive friction, blade binding

and kickback.

• Blade depth and bevel adjusting locking levers must be tight and

secure before making cut. If blade adjustment shifts while cutting, it may

cause binding and kickback.

• Use extra caution when sawing into existing walls or other blind areas.

The protruding blade may cut objects that can cause kickback.

Safety instructions for lower guard of saws

• Check the lower guard for proper closing before each use. Do not

operate the saw if the lower guard does not move freely and close

instantly. Never clamp or tie the lower guard into the open position.

If the saw is accidentally dropped, the lower guard may be bent. Raise the

lower guard with the retracting handle and make sure that it moves freely

and does not touch the blade or any other part, in all angles and all depths

of cut.

• Check the operation of the lower guard spring. If the guard and the

spring are not operating properly, they must be serviced before use.

The lower guard may operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

• The lower guard may be retracted manually only for special cuts,

such as “plunge cuts” and “compound cuts”. Raise the lower guard by

retracting the handle and, as soon as blade enters the material, the lower

guard must be released. For all other sawing, the lower guard should

operate automatically.

• Always observe that the lower guard is covering the blade before

placing saw down on bench or floor. An unprotected, coasting blade will

cause the saw to walk backwards, cutting whatever is in its path. Be aware

of the time it takes for the blade to stop after switch is released.

• To avoid personal injury, do not use the circular saw to make pocket cuts.

DESCRIPTION

KNOW YOUR CIRCULAR SAW (Fig. 1)

Fig. 1

Trigger Switch

Rear Handle

Lower-Blade-

Guard Lever

Front Handle

Bevel Scale

Bevel-

Adjustment

Knob

Edge-Guide

Lock Knob

Crosscut

Ruler

Lower Blade

Guard

Blade Screw

Base

Blade

Blade Wrench

Depth Scale

Lock-off

Button

Upper Blade Guard

Depth-of –Cut

Adjustment Lever

Spindle-Lock Button

PRODUCT SPECIFICATIONS

Rating 12 Amps

No-load Speed 5500 RPM

Blade Diameter 7 1/4 in. (184mm)

Blade Arb

or 5/8 in. (16mm)

Cutting Depth at 90°

2 1/2 in.

Cutting Depth at 45° 1 3/4 in.

Bevel Angle Adjustable 0-52°

ѥWARNING: The safe use of this product requires an understanding of the

information on the tool and in this operator’s manual, as well as knowledge of

the project you are attempting. Before use of this product, familiarize yourself

with all operating features and safety rules.

ERGONOMIC DESIGN

The design of the saw allows proper two-handed control when cutting. It has

been designed to be comfortable and easy to grasp.

0° TO 52° BEVEL ADJUSTMENT

The bevel adjustment lever allows you to set the circular saw for bevel cuts from

0° to 52°.

CROSSCUT RULER

The base has crosscut rulers for quick reference when making repetitive cuts.

SPINDLE-LOCK BUTTON

The spindle-lock button allows you to secure the blade when turning the

blade screw.

LOCK-OFF BUTTON

The lock-off button reduces the possibility of accidental starting.

DEPTH-OF-CUT ADJUSTMENT LEVER

The depth-of-cut adjustment lever adjusts the depth of cut a maximum of 2 1/2

in. at 90° and 1 3/4 in. at 45°.

BLADE-WRENCH STORAGE

When not in use, the blade wrench can be placed in the storage area located at

the base of the saw. Insert the blade wrench into the hole to store it.

ASSEMBLY

ѥWARNING: If any parts are broken or missing, do not attempt to plug or

operate the circular saw until the broken or missing parts are replaced. Failure

to do so could result in possibly serious injury.

ѥWARNING: Do not attempt to modify this circular saw or create

accessories not recommended for use with this saw. Any such alteration or

modification is misuse and could result in a hazardous condition leading to

possibly serious injury.

ѥWARNING: To prevent accidental starting that could cause serious

personal injury, always disconnect the circular saw from the power source

when changing blades.

UNPACKING

• Carefully remove the tool and any accessories from the carton. Make sure

that all items listed in the packing list are included.

• Inspect the tool carefully to make sure that no breakage or damage

occurred during shipping.

• Do not discard the packing material until you have carefully inspected and

satisfactorily operated the tool.

• If any parts are damaged or missing, please return the tool to the place

of purchase.

PACKING LIST

7 1/4 in. circular saw, blade wrench, blade and operator’s manual

TO INSTALL THE

BLADE (Fig. 2)

ѥWARNING: Be sure to wear

protective work gloves while

handling a saw blade. The blade

can injure unprotected hands.

1. Make sure that the saw is not

connected to a power source.

2. Place the saw on its side on a

at surface.

3. Raise the depth-of-cut

adjustment lever to loosen the base. Raise the saw to its maximum height

and tighten the depth-of-cut adjustment lever. This practice permits easier

access for blade mounting.

4. Depress the spindle-lock button and place the blade wrench on the blade

screw and move it back and forth until you feel the spindle-lock button

depress further.

5. With the spindle-lock button rmly depressed, turn the blade screw

counterclockwise to loosen it.

6. Use the blade-guard lever to raise the lower blade guard and hold it in the

raised position.

7. Remove the blade screw and the outer blade washer.

8. The remaining washer is the inner bushing washer that ts around the

spindle shaft and does not need to be removed.

9. Put a drop of good-quality machine oil onto the inner bushing washer and

outer blade washer where they will contact the blade.

10. Place a new saw blade inside the lower blade guard, onto the spindle shaft

and against the inner bushing washer.

NOTICE: The teeth of the blade should point upward at the front of the saw.

11. Replace the outer blade washer.

12. Depress and hold the spindle-lock button as you replace the blade screw

and hand-tighten the screw in a clockwise direction. Use the blade wrench

to tighten the blade screw securely.

13. Return the blade wrench into the storage area.

NOTICE: Never use a blade that is too thick to allow the outer blade washer to

engage with the at side of the spindle.

Fig. 2

Inner Bushing Washer

Blade

Blade Screw

Outer Blade Washer

Spindle Shaft

OPERATION

SAW BLADES

The best of saw blades will not cut efciently if they are not kept clean, sharp

and properly set.

Using a dull blade will place a heavy load on the saw and increase the danger of

kickback. Keep extra blades on hand, so that sharp blades are always available.

Gum and wood pitch hardened on the blades will slow the saw down. Use gum

and pitch remover, hot water or kerosene to remove these accumulations. DO

NOT USE GASOLINE.

ѥWARNING: A blade diameter of 7 1/4 in. is the maximum blade capacity of

your saw. A blade diameter greater than 7 1/4 in. will come in contact with the

blade guards. Never use a blade that is so thick that it prevents the outer blade

washer from engaging with the flat side of the spindle. Blades that are too large

or too thick can result in an accident causing serious injury.

BLADE GUARD SYSTEM

The lower blade guard attached to your circular saw is there for your protection

and safety. It should never be altered for any reason. If it becomes damaged

or begins to return slowly or sluggishly, do not operate your saw until the blade

guard has been repaired or replaced. Always leave the guard in its correct

operating position when using the saw.

ѥDANGER: When sawing through a workpiece, the lower blade guard does

not cover the blade on the underside of the workpiece. Since the blade is

exposed on the underside of the workpiece, keep hands and fingers away from

the cutting area. Any part of your body coming in contact with a moving blade

will result in serious injury.

ѥWARNING: Never use the saw when the guard is not operating properly.

The guard should be checked for correct operation before each use. If you drop

your saw, check that the lower blade guard and bumper for damage at all depth

settings before using.

ѥWARNING: When using the saw, always stay alert and exercise control. Do

not remove the saw from the workpiece while the blade is moving.

KICKBACK (Fig. 3, 4)

Kickback occurs when the blade stalls rapidly and the saw is driven back

towards you. Blade stalling is caused by any action that pinches the blade in

the wood. To avoid kickback, release the trigger switch immediately if the blade

binds or saw stalls. Kickback could cause you to lose control of the saw.

Loss of control can lead to serious injury.

Fig. 3

KICKBACK

DIRECTION OF CUT

Correct Blade Depth

Blade is Set Too Deep

To guard against kickback,

avoid dangerous practices,

such as the following:

1. Setting the blade

depth incorrectly.

2. Sawing into knots or nails in

the workpiece.

3. Twisting the blade while

making a cut.

4. Making a cut with a dull,

gummed up or improperly set blade.

5. Supporting the workpiece incorrectly (Fig. 4).

6. Forcing a cut.

7. Cutting warped or wet lumber.

8. Operating the tool incorrectly or misusing the tool.

9. Attempting to cut with blade at less than full speed.

ѥWARNING: If the blade comes in contact with the workpiece before it

reaches full speed, it could cause the saw to “kickback” towards you, which

could result in serious injury.

Wrong

Fig. 4

To lessen the chance

of kickback:

1. Keep the blade at the correct

depth setting. The depth

setting should not exceed 1/4

in. below the material being

cut (Fig. 5).

2. Inspect the workpiece for

knots or nails before

cutting. Never saw into a knot

or nail.

3. Make straight cuts. Always

use a straight edge guide

(available separately) when

rip cutting. This helps

prevent twisting of the blade.

4. Use clean, sharp and

properly set blades. Never

make cuts with dull blades.

5. Support the workpiece

properly before beginning

a cut (Fig. 6).

6. Use steady, even pressure

when making a cut. Never

force a cut.

7. Do not cut warped or wet lumber.

8. Hold the saw rmly with both hands and keep your body in a balanced

position so as to resist the kickback forces if kickback should occur.

ѥWARNING: To avoid kickback, release the trigger switch immediately if the

blade binds or the saw stalls. Kickback could cause you to lose control of the

saw. Loss of control can lead to serious injury.

Fig. 6

Correct Support

Fig. 5

1/4 in. maximum

LOCK-OFF BUTTON (Fig. 7)

The lock-off button reduces the

possibility of accidental starting.

The lock-off button is located

on the handle above the trigger

switch. The lock-off button must

be depressed before you pull the

trigger switch.

TRIGGER SWITCH (Fig. 7)

To turn the circular saw ON, depress the lock-off button, and then squeeze the

trigger switch. Do not touch the blade to the workpiece until the saw has

reached full speed.

To turn the circular saw OFF, release the trigger switch and allow it to return to

the “OFF” position.

After you release the trigger switch, allow the blade to come to a complete stop.

Do not remove the saw from the workpiece while the blade is moving.

DEPTH-OF-CUT ADJUSTMENT

Always use the correct blade-depth setting. The correct blade-depth setting for

all cuts should not be more than 1/4 in. below the material being cut. Allowing

more depth will increase the chance of kickback and cause the cut to be rough.

Your saw is equipped with a depth-of-cut scale that provides enhanced depth-

of-cut accuracy. The depth-of-cut scale is located on the inside back of the

upper blade guard.

TO ADJUST BLADE

DEPTH (Fig. 8)

1. Disconnect the circular saw

from the power source when

adjusting the depth of cut.

2. Raise the depth-of-cut

adjustment lever to loosen

the base.

3. Determine the desired depth

of cut.

4. Locate the depth scale on

the back of the upper

blade guard.

5. Hold the base at against the workpiece and raise or lower the saw until the

indicator aligns with the desired depth on the depth scale.

6. Tighten the depth-of-cut adjustment lever securely by lower it down.

Fig. 7

Trigger Switch

Lock-off Button

Fig. 8

Depth Scale

Depth-of-Cut

Adjustment Lever

Base

BEVEL ADJUSTMENTS

The angle of cut can be adjusted to any desired setting between 0°and 52°.

Because blade thicknesses vary and different angles require different settings,

always make a trial cut in scrap material along a guideline to determine how

much you should offset the guideline on the workpiece to be cut.

TO ADJUST BEVEL

SETTING (Fig. 9)

0°–45°bevel setting

1. Disconnect the circular saw

from the power source.

2. Loosen the bevel

adjustment knob by turning

it counterclockwise.

3. Raise the motor housing end

of the saw until the indicator

aligns with the desired angle

setting on the bevel scale.

4. Securely tighten the bevel-adjustment knob.

45°–52°bevel setting

1. Disconnect the circular saw from the power source when adjusting the

bevel setting.

2. Loosen the bevel adjustment knob by turning it counterclockwise.

3. Raise the 45° stop.

4. Raise the motor housing end of the saw, and tilt the base to the desired

setting on the bevel scale (45°–52°).

5. Tighten the bevel adjustment knob securely.

ѥWARNING: Attempting a bevel cut without having the bevel adjustment

knob securely tightened can result in serious injury.

Fig. 9

45°Quick

Adjustment

Position

Bevel

Adjustment

Knob

Indicator

Bevel Scale

OPERATING THE SAW

(Figs. 10, 11 and 12)

It is important to understand the

correct method for operating the

saw. Refer to the instructions in

this section to learn the correct

and incorrect ways for handling

the saw.

NOTICE: Install the blade on the

saw before operating the saw.

Refer to the ASSEMBLY section

of the manual.

ѥDANGER: When lifting the

saw from the workpiece, the

blade is exposed on the underside

of the saw until the lower blade

guard closes. Make sure that

the lower blade guard is closed

before setting the saw down.

ѥWARNING: To make sawing

easier and safer, always maintain

proper control of the saw. Loss of

control could cause an accident

resulting in possibly serious injury.

ѥWARNING: If the blade

comes in contact with the

workpiece before it reaches full

speed, it could cause the saw to

“kickback” towards you, which

could result in serious injury.

ѥWARNING: Always securely

clamp and support the workpiece.

Always maintain proper control

of the saw. Failure to clamp and

support the workpiece and the

resulting of loss of control of the saw could result in serious injury.

ѥWARNING: Do not bind the blade in the cut. It could cause the saw to

“kickback” towards you, which could result in serious injury.

ѥWARNING: To avoid personal injury, do not use the circular saw to make

pocket cuts.

Fig. 10

Fig. 11

Fig. 12

Page is loading ...

Craftsman 320.46123 Owner's manual

Brand: Craftsman

Model: 320.46123

Category: Power tools

Type: Owner's manual

This manual is also suitable for

3282

Download PDF

report

in other languages

español: Craftsman 320.46123 El manual del propietario

Craftsman 320.46123 Owner's manual

This manual is also suitable for

Craftsman 320.46123 Owner's manual

in other languages

Related papers