Page is loading ...
Welcome
Thank you for purchasing the new LED Bulb with Bluetooth Speaker
SY-LED1BT. In order to fully benefit from this product, please follow the
instructions in this user manual very carefully. Store this user manual in
a safe place for future reference. We are sure your new LED Bulb with
Bluetooth Speaker will satisfy your needs.
Parts of the SY-LED1BT
1 Bluetooth On/Off button
2 LED light ON/OFF
3 Previous song
4 Next song
5 LED brightness -
6 LED brightness+
7 Volume -
8 Pause/Play
9 Volume +
10 Bluetooth indicator
11 Battery door
12 LED light
13 Remote control
Safety Precautions
- Please read the following guidelines before using the LED bulb.
- Keep the LED bulb dry at all times
- Avoid exposing the unit to directly to sunlight or high temperatures.
- Do not expose the product to temperatures which are too low.
This will damage the internal circuit.
- Do not attempt to disassemble the product as this may cause damage.
- Do not drop on hard surfaces.
- Do not use chemicals or detergents to clean the LED bulb.
- Do not rub the product surface with sharp objects.
Using the Bulb
Connect the LED Lamp to the bulb socket (AC110V- 220V) and the LED
lamp will turn on.
Insert the correct battery into the remote control and close the battery
compartment with its cover.
Press the Bluetooth On/Off button (1) and hold it for 5 seconds, the
Bluetooth indicator (10) will ash. The Bluetooth device is now turned ON.
Press and hold the ON/OFF button (1) until the Bluetooth indicator ashes
and enters into pairing mode.
Press and hold the ON/OFF button (1) for 5 seconds till the Bluetooth
indicator flashes in order to turn off the Bluetooth function of the bulb
speaker.
When the bulb speaker is connected with the Bluetooth device, press the
Previous (3) or Next (4) buttons to change songs.
When the bulb speaker is connected with a Bluetooth device, to adjust the
volume press Volume Down (7), or Volume Up (9)
When the bulb speaker is connected with a Bluetooth device, press Play/
Pause (8) to play or pause the music.
To turn On/off the light of the bulb press the button (2).
Adjust the brightness of the bulb using buttons (5) and (6)
Installation
- Before installing the LED bulb into place, make sure that the
switch is turned off.
- Check that the base on which the LED bulb is going to be
installed is the correct one.
- Screw in the LED bulb rmly
- Turn on the light and wait a few seconds for the bulb to light up.
Pairing with other devices
Pairing with a mobile phone
- Keep the LED bulb and your mobile phone less than a meter away
during the pairing process.
- Turn on the LED bulb. It will search for Bluetooth devices which are
in range for 1 minute. If there is a device which has been
previously connected to the LED bulb before, the unit will connect to
it automatically, in the opposite case the device enters into pairing
mode automatically. You will then hear a beep sound and the blue
light will begin to ash to indicate that the unit is now in pairing mode.
- The Bluetooth function will turn off if there is no activity for 5 minutes and
the blue light begins to ash slowly. To return to the pairing mode,
please press and hold the button (1) for 3 seconds.
- Enable Bluetooth on your mobile phone to search for other Bluetooth
devices, after the search is completed, please select the
corresponding Bluetooth device from the list that appears.
- Enter the password "0000" and conrm if any password needed.
- Please click on "Connect" on “SY-LED1BT” when it shows up on the
paired devices list. You will then hear a beep sound and the blue
light will begin to ash. You may now transmit music from your mobile
phone to the Bluetooth LED lamp.
Notes:
- If there is an incoming call while the music is playing, the song will pause
and then resume after the call. (For some phones, you must manually
restart the playback).
- Press and hold the button (1) for 3 seconds to end the connection
between the bulb and the phone.
- The LED bulb will automatically connect to this device if its Bluetooth
function is turned on and it is within the range.
Technical Specications
Box Contents
1x Bulb Bluetooth speaker SY-LED1BT
1x Remote Control
1x User Manual
Version Bluetooth V3.0+EDR
Frequency response 80Hz-20kHz
Connection distance 10 meters, Class 2
Working temperature 0°C – 50°C
Storage temperature -20°C – 60°C (in original box )
Size Diameter (85mm) – height (129,5mm)
Weight 231g
Voltage: 110-220V, 50/60HZ
Max current: 800mA
Remote control: 2XAAA battery
Remote working distance Up to 10 meters, 2402~2480mHz
Speaker: 8Ω/5W
LED brightness 32LED, up to 300lumens
Declaration of Conformity
Manufacturer Name: Satyatrade S. L.
Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B83254763
Manufacturing country: China
Description: LED Bulb with Bluetooth Speaker
Sytech® SY-LED1BT complies with the following directives:
CE Standard: Directive 1995/5/EC
LVD Standard: 2006/95/EC
ROHS Standard: 2011/65/EC Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
/
