ELICA ENM230S1 Installation guide

1

Use, Care, and

Installation Guide

Guide

d’utilisation,

d’entretien et

d’installation

Guía de

instalación, uso y

mantenimiento

READ AND SAVE THESE

INSTRUCTIONS

LISEZ CES

INSTRUCTIONS ET

CONSERVEZ-LES

LEA Y CONSERVE

ESTAS INSTRUCCIONES

LIB0138588

Printed in Mexico

10/17

Models: ENM230S1

ENM236S1

2

ENGLISH

Contents

Important safety notice................................................................................................................................................................................................. 3

Electrical & installation requirements ................................................................................................................................................................ 4

Before installing the hood ...................................................................................................................................................................................... 4

Dimensions and clearances......................................................................................................................................................................................... 4

List of materials................................................................................................................................................................................................................. 5

Parts supplied .............................................................................................................................................................................................................. 5

Parts not supplied ...................................................................................................................................................................................................... 5

Ducting options and examples.................................................................................................................................................................................. 6

Installation ......................................................................................................................................................................................................................... 7

Electrical connection................................................................................................................................................................................................ 8

Complete the installation........................................................................................................................................................................................ 9

Description of the hood................................................................................................................................................................................................. 9

Control.................................................................................................................................................................................................................................. 9

Maintenance ...................................................................................................................................................................................................................... 10

Warranty ........................................................................................................................................................................................................................... 11

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Safety Warning: Turn o power circuit at service panel and lock out panel, before wiring this appliance.

Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit.

3

I

IMPORTANT SAFETY NOTICE

I CAUTION

FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO

EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR

VAPOURS.

I WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

B. Before servicing or cleaning the unit, switch power o

at service panel and lock service panel disconnecting

means to prevent power from being switched on

accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

C. Installation work and electrical wiring must be done by

qualiﬁed person(s) in accordance with all applicable

codes & standards, including ﬁre-rated construction.

D. Sucient air is needed for proper combustion and

exhausting of gases through the ﬂue (Chimney) of fuel

burning equipment to prevent back- drafting.

Follow the heating equipment manufacturers guideline

and safety standards such as those published by the

national ﬁre protection association (NFPA), the american

society for heating, refrigeration and air conditioning

engineers (ASHRAE), and the local code authorities.

E. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

F. Ducted systems must always be vented to the outdoors.

I CAUTION

To reduce risk of ﬁre and to properly exhaust air, be sure to

duct air outside - do not vent exhaust air into spaces within

walls, ceilings, attics, crawl spaces, or garages.

I WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT

WORK.

Install this hood in accordance with all requirements speciﬁed.

I WARNING

To reduce the risk of ﬁre or electric shock, do not use this

hood with any external solid state speed control device.

I WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

ﬂambeing food (I.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate

for the size of the surface element.

I WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet,

or other metal tray, then turn o the gas burner or the

electric element. BE CAREFUL TO PREVENT BURNS. If the

ﬂames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - you may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a class ABC extinguisher, and

you already know how to operate it.

2) The ﬁre is small and contained in the area where it

started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit.

e) Ducted fans must always be vented to the outdoor.

a

Based on “Kitchen Fire Safety Tips” published by NFPA.

4

ELECTRICAL & INSTALLATION REQUIREMENTS

IMPORTANT

Observe all governing codes and ordinances.

It is the customer’s responsibility:

• To contact a qualiﬁed electrical installer.

• To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No.0-M91-latest edition**

and all local codes and ordinances.

• If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualiﬁed electrician if you are not sure range

hood is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

IMPORTANT

• Save Installation Instructions for electrical inspector’s use.

• The range hood must be connected with copper wire only.

• The range hood should be connected directly to the fused

disconnect (Or circuit breaker) box through metal

electrical conduit.

• Wire sizes must conform to the requirements of the

National Electrical Code ANSI/NFPA 70 — latest edition*,

or CSA Standards C22.1-94, Canadian Electrical Code Part

1 and C22.2 No. 0-M91 - latest edition** and all local codes

and ordinances.

• A U.L.- or C.S.A.-listed conduit connector must be

provided at each end of the power supply conduit (at the

range hood and at the junction box).

Copies of the standards listed may be obtained from:

* National Fire Protection Association Batterymarch Park Quincy,

Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road Cleveland,

Ohio 44131-5575

BEFORE INSTALLING THE HOOD

1 For the most ecient air ﬂow exhaust, use a straight run

or as few elbows as possible.

CAUTION: Vent unit to outside of building, only.

2 At least two people are necessary for installation.

3 Fittings material is provided to secure the hood to most

types of walls/ceilings, consult a Qualiﬁed Installer,

check if they perfectly ﬁt with your cabinet/wall.

4 Do not use ﬂex ducting.

5 COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold air

ﬂow and a nonmetallic thermal break to minimize

conduction of outside temperatures as part of the

ductwork. The damper should be on the cold air side of

the thermal break.

The break should be as close as possible to where the

ducting enters the heated portion of the house.

6 Make up air: Local building codes may require the use of

Make-Up Air Systems when using Ducted Ventilation

Systems greater than speciﬁed CFM of air movement.

The speciﬁed CFM varies from locale to locale. Consult

your HVAC professional for speciﬁc requirements in your

area.

DIMENSIONS AND CLEARANCES

A

B

F

E

D

C

I

G

H

J

K

Models

ENM230S1 ENM236S1

A 30″ (76.2 cm) 36″ (91.4 cm)

B 18

5

⁄8″ (47.3 cm)

C 4

15

⁄16″ (12.5 cm)

D 1

1

⁄2″ (3.8 cm)

E 9″ (22.9 cm)

F 1″ (2.5 cm)

G 6

9

⁄16″ (16.7 cm)

H 1

15

⁄16″ (5 cm)

I

7

⁄8” (2.2 cm)

J 1

1

⁄16″ (2.6 cm)

K 1

7

⁄16″ (3.6 cm)

5

LIST OF MATERIALS

Removing the packaging.

I CAUTION

Remove carton carefully, Wear gloves to protect against sharp edges.

I WARNING

Remove the protective ﬁlm covering the product before putting into operation.

Supplied Part Pieces Supplied Part Pieces

Hood assembly and

LED lamps already installed

1

Rectangular duct 3

1

⁄4” x 10” (8.3 x 25.4 cm)

with back draft damper

1

4.5x13 mm

4

Grease ﬁlter

1

3.5x6.5 mm

2

Parts no supplied

Tools/Materials required

• Drill

• 1

1

⁄4” (3.0 cm) drill bit

•

1

⁄8” (3.0 mm) drill bit for pilot holes

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Caulking gun and weatherproof caulking compound

• Saber or keyhole saw

• Metal snips

• Screwdrivers:

- Phillips

- Flat-blade

Optional accessories and consumable parts

KIT # Part

Recirculating Kit KIT0140997

7” Round Kit KIT02722

7” Round Back

Draft Damper Kit

KIT02723

6

Ducting Options

Closely follow the instructions set out in this manual.

All responsability, for any eventual inconveniences, damages or ﬁres caused by not complying with the instructions in this manual,

is declined.

Ducting version Ductless (Recirculating)

a) 3



⁄4” x 10” (8.3 x 25.4 cm) rectangular vent through the roof/wall (purchased

separately).

b) Roof/wall cap (purchased separately)

A

B

A

B

Roof Venting Wall Venting

In cases where it should not

be possible to discharge

cooking fumes and vapour

to the outside, purchase

the Ductless Recirculating

Kit.

For ductless (Recirculating)

version only.

a) Charcoal ﬁlter

b) Recirculation cover plate

c) Cabinet

A

B

C

Preparation

Do not cut a joist or stud unless absolutely necessary. If a joist

or stud must be cut, then a supporting frame must be

constructed.

Fittings material is provided to secure the hood to most types

of walls/ceilings.

However, a qualiﬁed technician must verify suitability of the

materials in accordance with the type of wall/ceiling.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

Recommended installation height:

Hood installation height above cooktop is the users preference.

The lower the hood is above the cooktop, the more ecient

the capturing of cooking odors, grease and smoke.

I CAUTION

FOR GAS RANGES INSTALLATION: MOUNT THIS HOOD SO

THAT THE BOTTOM IS NOT LESS THAN 27” (68.6 CM).

FOR ELECTRIC RANGES INSTALLATION: MOUNT THIS HOOD

SO THAT THE BOTTOM IS NOT LESS THAN 24” (61 CM)

AND NOT MORE THAT 30” (76.2 CM) ABOVE THE COOKING

SURFACE.

Check your ceiling height and the hood height maximum

before you select your hood.

Prepare Location

NOTE: It is recommended that the vent system be installed

before hood is installed. Before making cutouts, make sure

there is proper clearance within the ceiling or wall for exhaust

vent.

1 Disconnect power.

2 Depending on your model, determine which venting

method to use: roof, wall or recirculating.

3 Select a ﬂat surface for assembling the range hood. Place

covering over that surface.

Lift the range hood and set it upside down onto covered

surface.

For recessed bottom cabinet only

1 If the cabinets have front, side or back trim, make 2 wood

shims the width of the trim and attach them to the cabinet

bottom recess on both sides. See the diagramas for marking

locations.

IMPORTANT: Align the wood ﬁller strips so that they

completely cover the recessed bottom cabinet.

Wood shims

Determine Wiring Hole Location

Cut only one 1

1

⁄4” (3.2 cm) diameter wiring access hole.

1 Determine and clearly mark a vertical centerline on the

wall and cabinet in the area the vent opening will be made.

A. Centerline

A

7

To wire through top:

2 Mark a line 8

3

⁄8” (21.3 cm) from the right of the centerline

on the underside of the cabinet. For 12” (30.5 cm) deep

cabinets, mark the point on this line that is 2” (5.1 cm)

from the back wall. For 15” (38.1 cm) deep cabinets, mark

the point on this line that is 5” (12.7 cm) from the back

wall. Drill a 1¼” (3.2 cm) diameter hole through the cabinet

at this point.

8

3

⁄8” (21.3 cm)

Centerline

*2” (5.1 cm) for 12”

(30.5 cm) deep cabinets

*5” (12.7 cm) for 15”

(38.1 cm) deep cabinets

*from wall, not cabinet frame

To wire through wall:

1 Mark a line 8

3

⁄8” (21.3 cm) from the right of the centerline

on the underside of the wall. Mark the point on this line that

is

7

⁄8” (2.2 cm) from the underside of the cabinet. Drill a 1

1

⁄4”

(3.2 cm) diameter hole through the rear wall at this point.

8

3

⁄8”

(21.3 cm)

7

⁄8” (2.2 cm)

Centerline

Cut Openings for 3¼” x 10” (8.3 cm x 25.4 cm)

Rectangular Vent System

Roof Venting

To make a 4

1

⁄4” x 10½” (10.8 cm x 26.7 cm) rectangular cutout

on the underside of cabinet top and bottom:

1 Mark lines

1

⁄2” (1.3 cm) and 4

3

⁄4” (12.1 cm) from the back wall

on the centerline of the underside of cabinet.

2 Mark lines 5¼” (13.3 cm) to the right and left of the center-

line on the underside of cabinet.

3 Use saber or keyhole saw to cut a rectangular opening for

vent.

4 Repeat steps 1-3 for the underside of the top of the cabinet.

Cabinet cutouts

1” (2.5 cm)

*From wall, not cabinet frame

5”

(12.7 cm)

5

1

⁄4”

(13.3 cm)

5

1

⁄4”

(13.3 cm)

Wall Venting

To make a 4

1

⁄4” x 10½” (10.8 cm x 26.7 cm) rectangle in the wall:

1 Make 2 lines by measuring

1

⁄8” (0.3 cm) and 4

1

⁄16” (10.3 cm)

down from underside of cabinet and mark on the centerline

on the back wall.

2 Mark lines 5¼” (13.3 cm) to the right and left of the centerline

on the wall.

3 Use saber or keyhole saw to cut a rectangular opening in

the wall for the vent.

Cabinet

front

4

1

⁄4”

(10.8 cm)

1

⁄8”

(0.3 cm)

Centerline

5

1

⁄4”

(13.3 cm)

5

1

⁄4”

(13.3 cm)

Installation

• Lift the range hood up under cabinet and determine ﬁnal

location by centering beneath cabinet. Mark on the

underside of cabinet the location of the 4 keyhole

mounting slots on the range hood. Set range hood aside

on a covered surface.

A

A. Keyhole slot

• Use ⁄8” (3 mm) drill bit and drill 4 pilot holes as shown.

A

A. Drill pilot hole

• Install the 4 - 4.5 mm x 13 mm mounting screws in pilot

holes. Leave about ⁄4” (6.4 mm) space between screw

heads and cabinet to slide range hood into place.

1

⁄4″

(6.4 mm)

• Remove transition knockouts depending on the selected

venting method.

C

D

A

B

A. Top rectangular vent knockout

B. Rear rectangular vent knockout

C. Round vent knockout

D. Recirculation cover plate

Top venting outlet (exit through the wall or the roof):

For rectangular vent system installations, remove the top

rectangular knockout.

NOTE: For round vent system installations, remove the top

round knockout.

Rear venting outlet (exit through the wall):

Remove the rear rectangular knockout.

Non-ducted (recirculating) installations - No vent attachments.

Remove the two screws from the recirculation cover plate and

set it aside. See the Recirculating installations section.

• Remove metal grease ﬁlters. See the “Range Hood Care”

section. First remove the bracket and then the lateral panels.

NOTE: You will have 3

1

⁄4” x 10” (8.3 x 25.4 cm) rectangular

vent transition inside your range hood. Remove the 3-

1

⁄4” x

10” (8.3 x 25.4 cm) rectangular vent transition inside your

range hood.

8

A

A. Lateral panels

• Install 3

1

⁄4 x 10” (8.3 x 25.4 cm) vent connector, depending

on the vent system installation.

NOTE: The 3

1

⁄4 x 10” (8.3 x 25.4 cm) rectangular vent connector

can be installed up to 1” (2.5 cm) on either side of the hood

center to accommodate o center ductwork.

B

C

A

D

A. Vertical connector

B. 6.5 x 9.5 mm screws

C. Vent knockouts

D. Horizontal connector

• For round installation: Install 7” (17.8 cm) round vent

mounting plate and damper (purchase as an accesory).

A

B

C

E

D

A. 7” (17.8 cm) round damper

B. Sheet metal screws

C. 7” (17.8 cm) round vent mounting plate

D. Round vent knockout

E. Rectangular vent knockout

• If a vent damper is installed with a wall cap with damper,

check to make sure they do not interfere with each other.

Remove the vent connector damper ﬂap if they interfere.

Non-ducted (recirculating) installations - No vent attachments.

It requires the removal of the recirculation cover plate.

Remove the two screws from the recirculation cover plate and

remove.

A

B

A. Screws (2)

B. Recirculation cover plate

Electrical Connection

I WARNING

Electrical Shock Hazard

I WARNING

Turn o power circuit at the service panel before wiring this

unit. 120 VAC, 15 or 20 Amp circuit required.

ELECTRICAL GROUNDING INSTRUCTIONS

THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION

BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW)

SERVES TO GROUND THE APPLIANCE. TO PROTECT YOU

AGAINST ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE

MUST BE CONNECTED TO THE GROUNDING WIRE IN YOUR

HOME ELECTRICAL SYSTEM, AND IT MUST UNDER NO

CIRCUMSTANCES BE CUT OR REMOVED.

Failure to do so can result in death or electrical shock.

• Remove the knockout and the Junction box cover and

install the conduit connector (cULus listed) in junction box.

A

A. Terminal box cover

9

• Run 3 wires; black, white and green ,according to the

National Electrical Code and local codes and ordinances,

in

1

⁄2” conduit from service panel to junction box.

G

E

A

B

C

F

D

A. White wires

B. Black wires

C. UL listed wire connector

D. Green (or bare) ground wire

E. Home power supply cable

or power cord accessory kit

F. UL listed or CSA approved

½” strain relief

G. Green ground screw

• Connect black wire from service panel to black or red in

junction box, white to white and green to green-yellow.

• Close and secure junction box cover.

Complete Installation

• Lift the hood into ﬁnal position. Feed enough electrical

wire through the ½” UL listed or CSA approved strain relief

to make connections in the terminal box. Tighten the strain

relief screws.

• Position the range hood so that the large end of the keyhole

slots are over the mounting screws. Then push the hood

toward the wall so that the screws are in the neck of the

slots.

A

B

A. Mounting screws (4)

B. Security screws

• Tighten the mounting screws, making sure the screws are

in the narrow neck of slots.

• Connect ventwork to hood. Seal joints with clamps to

make secure and airtight.

• Check that back draft dampers work properly.

• Replace filters. See the “Range Hood Care”.

Check operation of the hood.

If range hood does not operate:

• Check that the circuit breaker is not tripped or the house

fuse blown.

• Disconnect power supply. Check that wiring is correct.

To get the most efficient use from your new range hood, read

the “Use and Care Information” section.

Keep your Installation Instructions and Use and Care Guide

close to range hood for easy reference.

Description of the Hood

3

6

1

2

3

4

5

1. Control

2. LED lights

3. Lateral panels

4. Bracket

5. Grease ﬁlter

6. Grease ﬁlter handle

Controls

1. Light On/O button

2. Blower On/O button

3. Blower speed minimum button

4. Blower speed medium button

5. Blower speed maximum button

NOTE: Control buttons will light up when range hood is On.

Operating the light

The Light On/O button (1) controls both lights. Press once

for On and again for O.

Operating the blower

The Blower On/O button (2) turns the blower On or O.

The Blower Speed buttons (3, 4 and 5) set the desired speed

and control the sound level for quiet operation. The speed

can be changed anytime during fan operation by pressing the

desired blower speed button.

1 To turn the blower On, press the Blower On/O button (2)

and the desired speed button (3, 4 or 5).

2 To turn the blower O, press the Blower On/O button (2).

Any of the 3 blower speed buttons can be in the On position

at the same time. The blower will operate at the highest speed

button that is pushed in. For lower blower speeds, the higher

speed buttons must not be pushed in.

10

Range Hood Care

Cleaning

Do not spray cleaners directly to the control while cleaning the

Hood. The cooker hood should be cleaned regularly (at least

with the same frequency with which you carry out maintenance

of the fat ﬁlters) internally and externally. Clean using the

cloth dampened with neutral liquid detergent. Do not use

abrasive products.

DO NOT USE ALCOHOL!

I WARNING:

Failure to carry out the basic cleaning recommendations of the

cooker hood and replacement of the filters may cause fire risks.

Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate maintenance

or failure to observe the above safety recommendations.

Grease ﬁlter

Traps cooking grease particles.

This must be cleaned once a month using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle. When washed

in a dishwasher, the grease filter may discolour slightly, but

this does not affect its filtering capacity.

To remove the grease filter

1 Remove the grease ﬁlter bracket.

B

A

A. Bracket

B. Grease ﬁlter bracket screws (2)

2 Pull the spring release handle to remove the grease ﬁlter.

A

3 Reinstall the ﬁlter by placing the back edge in the channel

at rear of hood.

4 Replace the bracket using the screws that were previously

removed in step 1.

Replacing a LED Lamp

The LED lights are replaceable by a service technician only.

See the service contact information in this page below.

Charcoal ﬁlter

If the model is not vented to the outside, the air will be

recirculated through disposable charcoal filter that help remove

smoke and odors.

The charcoal filter cannot be cleaned.

It must be replaced.

The charcoal filter is clipped inside of the metal grease filter

The charcoal filter should be replaced every 4-6 months

(depending on hood usage).

NOTE: DO NOT rinse, or put charcoal ﬁlter in an automatic

dishwasher.

NOTE: Charcoal ﬁlter is not included with the hood.

It must be ordered from your supplier.

Order the needed kit specifying your hood model and width

size.

Charcoal ﬁlter placement (Recirculating accessories)

Fit the charcoal filter mattress on the upper side of the grease

filter.

Use provided rods to ﬁx it in place.

NOTE: Place each rod into the hole in A side and then into the

next hole in B side of the charcoal ﬁlter as the image below.

Rod

Charcoal filter

Holes in

A Side

Holes in

B Side

ELICA North America

TWO-YEARS LIMITED WARRANTY

TO OBTAIN SERVICE UNDER WARRANTY

Owner must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in

order to obtain service under warranty.

PARTS AND SERVICE WARRANTY

For the period of two (2) years from the date of the original purchase, Elica will provide free of charge, non consumable

parts or components that failed due to manufacturing defects. During these two (2) years limited warranty, Elica will also

provide free of charge, all labor and in-home service to replace any defective parts.

WHAT IS NOT COVERED

• Damage or failure to the product caused by accident or act of God, such as, ﬂood, ﬁre or earthquake.

• Damage or failure caused by modiﬁcation of the product or use of non-genuine parts.

• Damage or failure to the product caused during delivery, handling or installation.

• Damage or failure to the product caused by operator abuse.

• Damage or failure to the product caused by dwelling fuse replacement or resetting of circuit breakers.

• Damage or failure caused by use of product in a commercial application.

• Service trips to dwelling to provide use or installation guidance.

• Light bulbs, metal or carbon ﬁlters and any other consumable part.

• Normal wear of ﬁnish.

• Wear to ﬁnish due to operator abuse, improper maintenance, use of corrosive or abrasive cleaning products/pads and

oven cleaner products.

WHO IS COVERED

This warranty is extended to the original purchaser for products purchased for ordinary residential use in North America

(Including the United States, Guam, Puerto Rico, US Virgin Islands & Canada).

This warranty is non-transferable and applies only to the original purchaser and does not extend to subsequent owners of

the product. This warranty is made expressly in lieu of all other warranties, expressed or implied, including, but not limited

to any implied warranty of merchantability or ﬁtness for a particular purpose and all other obligations on the part of Elica

North America, provided, however, that if the disclaimer of implied warranties is ineective under applicable law, the dura-

tion of any implied warranty arising by operation of law shall be limited to two (2) years from the date of original purchase

at retail or such longer period as may be required by applicable law.

Th

is warranty does not cover any special, incidental and/or consequential damages, nor loss of proﬁts, suered by the

original purchaser, its customers and/or the users of the Products.

WHO TO CONTACT

To obtain service under warranty or for any service related question:

• Elica North America Service, call at 1 888 732 8018

• For Eastern Canada, call AGI Services at 1 888 651 2534 Ask for the service department

• elica@servicepower.com

Page is loading ...

ELICA ENM230S1 Installation guide

This manual is also suitable for

ELICA ENM230S1 Installation guide

in other languages

Related papers

Other documents