Ferris 5900832 User manual

Brand: Ferris

Model: 5900832

Category: Lawnmowers

Type: User manual

This manual is also suitable for

5102059

Revision G

Briggs & Stratton Power Products Group, LLC.

5375 North Main Street

Munnsville, NY 13409

800-933-6175

IS1500Z Series

Zero-Turn Riding Mower

OPERATOR’S

MANUAL

Model No.: Description Horsepower Deck Size Serial Number:

5900832 IS1500ZKAV2552 AUS/NZ 25HP 52” Side Discharge All

5900833 IS1500ZKAV2552 25HP 52” Side Discharge All

5900836 IS1500ZKAV2552 CAL 25HP 52” Side Discharge All

5900877 IS1500ZKAV2048 20HP 48” Side Discharge 2014744586 & Above

5900576 IS1500ZKAV1948 19HP 48” Side Discharge All

5900589 IS1500ZB2648 26HP 48” Side Discharge All

Not for

Reproduction

WARNING

Engine exhaust from this product contains

chemicals known by the State of California to

cause cancer, birth defects, or other reproductive

harm.

Thank you for purchasing this quality-built Ferris product. We’re pleased that you’ve placed your confidence in the

Ferris brand. When operated and maintained according to the instructions in this manual, your Ferris product will

provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with this machine

and how to avoid them. This machine is designed and intended to be used and maintained according to the manual

and operated by trained professionals for finish cutting of established lawns and is not intended for any other

purpose. It is important that you read and understand these instructions thoroughly before attempting to start or

operate this equipment

Briggs & Stratton Power Products Group, LLC.

The Ferris logo is a trademark of Briggs & Stratton

Corporation Milwaukee, WI, USA.

Contact Information:

Briggs & Stratton Power Products Group, LLC

5375 N. Main St.

Munnsville, NY 13409-4003

(800) 933-6175

www.ferrisindustries.com

WARNING

Battery posts, terminals, and related accessories

contain lead and lead compounds — chemicals

known to the State of California to cause cancer

and reproductive harm.

Wash hands after handling.

PRODUCT REFERENCE DATA

Unit Model Number Unit SERIAL Number

Mower Deck Model Number Mower Deck SERIAL Number

Dealer Name Date Purchased

ENGINE REFERENCE DATA

Engine Make Engine Model

Engine Type/Spec. Engine Code/Serial Number

SAMPLE

When contacting your authorized dealer for

replacement parts, service, or information you

MUST have these numbers.

Record your part number, serial number and engine

serial numbers in the space provided for easy access.

These numbers can be found in the locations shown.

NOTE: For location of engine identification numbers,

refer to the engine owner’s manual.

Identification

Tag

USA Models

Identification Numbers

Not for

Reproduction

Table of Contents

Operator Safety .................................................. 2

Safety Decals ........................................................11

Safety Interlock System ........................................12

USA Safety Icons ..................................................12

Features & Controls ......................................... 13

Control Functions ..................................................13

Operation ........................................................... 15

General .................................................................15

Checks Before Starting .........................................15

Starting the Engine ...............................................16

Stopping the Rider ................................................16

Pushing the Rider by Hand ...................................16

Zero Turn Driving Practice ....................................17

Mowing ..................................................................19

Mowing Reccomendations ....................................19

Mowing Methods ...................................................20

Attaching a Trailer .................................................21

Raise & Lower the Roll Bar ..................................22

Storage .................................................................23

Starting After Long Term Storage .........................23

Regular Maintenance ....................................... 24

Maintenance Schedule .........................................24

Checking Tire Pressures ......................................25

Checking/Adding Fuel ...........................................25

Fuel Filter ..............................................................25

Oil & Filter Change ...............................................26

Engine Maintenance .............................................26

Inspect Muffler / Spark Arrester ............................26

Check Hydraulic Oil Level .....................................26

Hydraulic Oil Filter Change ...................................27

Cleaning the Battery and Cables ..........................27

Lubrication ............................................................28

Servicing the Mower Blades .................................29

Seat Adjustment ....................................................31

Ground Speed Control Lever Adjustment .............31

Speed Balancing Adjustment ................................31

Parking Brake Adjustment ....................................32

Rear Suspension Adjustment ...............................33

Return to Neutral Adjustment ...............................34

Neutral Adjustment ...............................................34

Mowing Height Adjustment ...................................35

Foot Pedal Adjustment .........................................35

Deck Leveling Adjustment ....................................36

Hydraulic Pump Drive Belt Replacement .............38

Mower Belt Replacement ......................................39

Battery Service ......................................................41

Troubleshooting, Adjustments & Service ...... 43

Troubleshooting the Tractor ..................................43

Troubleshooting the Mower ..................................44

Troubleshooting Common Cutting Problems ........45

Specifications ................................................... 46

Slope Identification Guide ............................... 47

NOTE: In this manual, “left” and “right” are referred to as

seen from the operating position.

Not for

Reproduction

Operator Safety

Operating Safety

Congratulations on purchasing a superior-quality piece of

lawn and garden equipment. Our products are designed and

manufactured to meet or exceed all industry standards for safety.

Do not operate this machine unless you have been trained.

Reading and understanding this operator’s manual is a way to

train yourself.

Power equipment is only as safe as the operator. If it is misused,

or not properly maintained, it can be dangerous! Remember, you

are responsible for your safety and that of those around you.

Use common sense, and think through what you are doing. If

you are not sure that the task you are about to perform can be

safely done with the equipment you have chosen, ask a

professional: contact your local authorized dealer.

Read the Manual

The operator’s manual contains important safety

information you need to be aware of BEFORE you

operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the

product’s features and controls, and maintenance

information is included to help you get the most out of

your equipment investment.

Be sure to completely read the Safety Rules and

Information found on the following pages. Also

completely read the Operation section.

Children

Tragic accidents can occur with children. Do

not allow them anywhere near the area of

operation. Children are often attracted to the

unit and mowing activity. Never assume that

children will remain where you last saw them.

If there is a risk that children may enter the

area where you are mowing, have another

responsible adult watch them.

Not for

Reproduction

Operator Safety

Slope Operation

Operation on slopes can be dangerous. Using the unit on a slope

that is too steep where you do not have adequate wheel traction

(and control) can cause sliding, loss of steering, control, and

possible rollover. You should not operate on a slope greater than

a 5.4 foot rise over a 20 foot length (15 degrees).

Always mow across slopes, not up and down (to maintain traction

on the wheels) and avoid sudden turns or rapid speed changes.

Reduce speed and use extreme caution on ALL slopes.

Also, note that the surface condition you are on can greatly impact

your ability to safely operate this machine. Operating on wet or

slippery slopes can cause sliding and loss of steering and control.

Do not operate on slopes that are slippery, wet, or have soft soil

conditions.

If you feel unsure about operating the unit on a slope, don’t do it.

It’s not worth the risk.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and

throw debris that could seriously injure a bystander. Be sure to clean

up the area to be mowed and remove objects that could be thrown by

the blade BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge

guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If

someone does enter the area, shut the unit off immediately until they

leave.

Moving Parts

This equipment has many moving parts that can injure

you or someone else. However, if you stay in the

operator zone (stay seated in the seat), and follow the

safety rules in this operator’s manual, the unit is safe to

operate.

The mower deck has spinning mower blades that can

amputate hands and feet. Do not allow anyone near the

unit while it is running! Keep safety devices (guards,

shields, and switches) in place and working.

To help you, the operator, use this equipment safely, it

is equipped with an operator-present safety system. Do

NOT attempt to alter or bypass the system. See your

dealer immediately if the system does not pass all the

safety interlock system tests found in this manual.

Not for

Reproduction

Roll Bar Use

Keep the roll bar in the raised position and fasten the

seat belt. There is no roll over protection when the

roll bar is down! Do not jump off if the mower tips (it

is safer to be secured by the seat belt with the roll bar

raised.)

Lower the roll bar only when necessary (such as to

temporarily clear a low overhanging obstacle) and

NEVER remove it. Do NOT use the seat belt when

the roll bar is down. Raise the roll bar as soon as

clearance permits.

Retaining Walls, Drop-

offs, and Water

Retaining walls and drop-offs around steps and

water are a common hazard. Give yourself a

minimum of two mower widths of clearance

around these hazards and hand-trim with a

walk behind mower or string trimmer. Wheels

dropping over retaining walls, edges, ditches,

embankments, or into water can cause rollovers,

which may result in serious injury, death, or

drowning.

Overhead Obstacles

Check for overhead clearances before driving

under any objects. Do not allow the roll bar to

contact low overhanging obstacles such as tree

branches and guide wires.

Operator Safety

Not for

Reproduction

Operator Safety

Enclosed Areas

Only operate this unit outdoors and

away from unventilated areas such as

inside garages or enclosed trailers.

The engine emits poisonous carbon

monoxide gas and prolonged exposure

in an enclosed area can result in

serious injury or death.

Fuel and Maintenance

Always disengage all drives, shutoff the engine, and

remove the key before doing any cleaning, refueling, or

servicing.

Gasoline and its vapors are extremely flammable. Do not

smoke while operating or refueling. Do not add fuel while

engine is hot or running. Allow engine to cool for at least

3 minutes prior to adding fuel.

Do not add fuel indoors, in an enclosed trailer, garage,

or any other enclosed area that is not well ventilated.

Gasoline spills should be cleaned up promptly and before

operation begins.

Gasoline should be stored only in sealed containers

approved for fuel.

Proper maintenance is critical to the safety and

performance of your unit. Keep the unit free of

grass, leaves, and excess oil. Be sure to perform the

maintenance procedures listed in this manual, especially

periodically testing the safety system.

Not for

Reproduction

2. Mow only in the daylight or with good artificial

light, keeping away from holes and hidden

hazards.

3. Be sure all drives are in neutral and parking brake

is engaged before starting engine. Only start

engine from the operator’s position. Use seat

belts if provided.

4. Be sure of your footing while using pedestrian

controlled equipment, especially when backing up.

Walk, don’t run. Reduced footing could cause

slipping.

5. Slow down and use extra care on hillsides. Be

sure to travel in the recommended direction on

hillsides. Turf conditions can affect the machines

stability. Use caution when operating near drop-

offs.

6. Do not mow in reverse unless absolutely

necessary. Always look down and behind before

and while traveling in reverse.

7. Be aware of the mower discharge direction and do

not point it at anyone. Do not operate the mower

without either the entire grass catcher or the

deflector in place.

8. Slow down and use caution when making turns

and when changing directions on slopes.

9. Never raise deck with the blades running.

10. Never leave a running unit unattended. Always

disengage the PTO, set parking brake, stop

engine, and remove keys before dismounting.

Keep hands and feet away from the cutting units.

11. Turn off the PTO switch to disengage the blades

when not mowing.

12. Never operate with guards not securely in place.

Be sure all interlocks are attached, adjusted

properly and functioning properly.

13. Never operate with the discharge deflector raised,

removed or altered, unless using a grass catcher.

14. Do not change the engine governor setting or

overspeed the engine.

15. Stop on level ground, lower implements,

disengage drives, engage parking brake, shut off

engine before leaving the operator’s position for

any reason including emptying the grass catchers

or unclogging the chute.

16. Stop equipment and inspect blades after striking

objects or abnormal vibration occurs. Make

necessary repairs before resuming operations.

17. Keep hands and feet away from the cutting units.

18. Look behind and down before backing up to be

sure of a clear path.

19. Never carry passengers and keep pets and

bystanders away.

20. Do not operate the unit while under the influence

of alcohol or drugs.

21. Slow down and use caution when making turns

and crossing roads and sidewalks. Stop blades if

not mowing.

22. Use care when loading or unloading the machine

into a trailer or truck.

TRAINING

1. Read, understand, and follow all instructions in

the manual and on the unit before starting. If the

operator(s) or mechanic(s) can not read English

it is the owner’s responsibility to explain this

material to them.

2. Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

3. All operators and mechanics should be trained.

The owner is responsible for training the users.

4. Only allow responsible adults, who are familiar

with the instructions, to operate the unit.

5. Never let children or untrained people operate

or service the equipment. Local regulations may

restrict the age of the operator.

6. The owner/user can prevent and is responsible

for accidents or injuries occurring to themselves,

other people or property.

7. Data indicates that operators, age 60 years and

above, are involved in a large percentage of riding

mower-related injuries. These operators should

evaluate their ability to operate the riding mower

safely enough to protect themselves and others

from serious injury.

PREPARATION

1. Evaluate the terrain to determine what

accessories and attachments are needed to

properly and safely perform the job. Use only

accessories and attachments approved by the

manufacturer.

2. Wear appropriate clothing including safety shoes,

safety glasses and ear protection. Long hair,

loose clothing or jewelry may get tangled in

moving parts.

3. Inspect the area where the equipment is to be

used and remove all objects such as rocks, toys

and wire, which can be thrown by the machine.

4. Use extra care when handling gasoline and

other fuels. They are flammable and vapors are

explosive.

a) Use only an approved container.

b) Never remove fuel cap or add fuel with the

engine running. Allow engine to cool before

refueling. Do not smoke.

c) Never refuel or drain the machine indoors.

5. Check that operator’s presence controls, safety

switches and shields are attached and functioning

properly. Do not operate unless they are

functioning properly.

OPERATION

1. Never run an engine in an enclosed area.

Read these safety rules and follow them closely. Failure to obey these rules could result in loss

of control of unit, severe personal injury or death to you, or bystanders, or damage to property or

equipment. This mowing deck is capable of amputating hands and feet and throwing objects.

The triangle in text signifies important cautions or warnings which must be followed.

Operator Safety

Not for

Reproduction

Operator Safety

23. Use care when approaching blind corners, shrubs,

trees or other objects that may obscure vision.

24. To reduce fire hazard, keep unit free of grass,

leaves & excess oil. Do not stop or park over dry

leaves, grass or combustible materials.

25. OSHA regulations may require the use of hearing

protection when exposed to sound levels greater

than 85 dBA for an 8 hour time period.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and

tip-over accidents, which can result in severe injury or

death. All slopes require extra caution. If you cannot

back up the slope or if you feel uneasy on it, do not

drive on it.

1. Mow across slopes, not up and down.

2. Remove obstacles such as rocks, tree limbs, etc.

3. Watch for holes, ruts, or bumps. Uneven terrain

could overturn the unit. Tall grass can hide

obstacles.

4. Use slow speed. Choose a slow speed so that

you will not have to stop or change speed while

on the slope.

5. Use extra care with grass catchers or other

attachments. These can change the stability of

the unit.

6. Keep all movement on the slopes slow and

gradual. Do not make sudden changes in speed

or direction.

7. See your authorized dealer for recommendations

of available weights to improve stability.

Do Not

1. Avoid starting, stopping, or turning on a slope.

If tires lose traction (i.e. machine stops forward

motion on a slope), disengage the blade(s) (PTO)

and drive slow off the slope.

2. Do not turn on slopes unless necessary, and then,

turn slowly and gradually uphill, if possible. Never

mow down slopes.

3. Do not mow near drop-offs, ditches, or

embankments. The operator could lose footing or

balance or mower could suddenly turn over if a

wheel is over the edge of a cliff or ditch, or if an

edge caves in.

4. Do not mow on wet grass. Reduced footing or

traction could cause sliding.

5. Do not try to stabilize the unit by putting your foot

on the ground. (ride-on units)

6. Do not mow excessively steep slopes.

7. Do not use grass catcher on steep slopes.

8. Do not mow slopes if you cannot back up them.

TOWED EQUIPMENT (RIDE-ON UNITS)

1. Tow only with a machine that has a hitch designed

for towing. Do not attach towed equipment except

at the hitch point.

2. Follow the manufacturer’s recommendations

for weight limit for towed equipment and

towing on slopes. See attaching a trailer under

OPERATION.

3. Never allow children or others in or on towed

equipment.

4. On slopes, the weight of the towed equipment

may cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

CHILDREN

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted

to the unit and the mowing activity. Never assume that

children will remain where you last saw them.

1. Keep children out of the mowing area and under

the watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind

and down for small children.

4. Never carry children, even with the blade(s) off.

They may fall off and be seriously injured or

interfere with safe unit operation. Children who

have been given rides in the past may suddenly

appear in the mowing area for another ride and be

run over or backed over by the machine.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision.

CAUTION

This machine produces sound levels

in excess of 85 dBA at the operator’s

ear and can cause hearing loss

though extended periods of exposure.

Wear hearing protection when operating this

machine.

WARNING

Do not use this machine on slopes greater than

15°.*

Select slow ground speed before driving onto

slope. Use extra caution when operating on

slopes with rear-mounted grass catchers.

Mow across the face of slopes, not up and

down, use caution when changing directions

and DO NOT START OR STOP ON SLOPE.

*This limit was determined per CEN Standard EN 836:1997, Section

5.2.2 and is based on the EN 836 Stability Test procedure described in

Section 4.2.4.2. The 15 degree “limit of stability” is equal to 50% of the

angle at which machine lift-off occurred in static tests. Actual dynamic

stability may vary depending on operating conditions.

WARNING

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered

or grass-covered land unless the exhaust

system is equipped with a spark arrester,

as defined in Section 4442, maintained in

effective working order. Other states or federal

jurisdictions may have similar laws. Contact

an Authorized Service Dealer to obtain a spark

arrester designed for the exhaust system

installed on this engine.

Not for

Reproduction

Operator Safety

EMISSIONS

1. Engine exhaust from this product contains

chemicals known, in certain quantities, to cause

cancer, birth defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period

and Air Index information on the engine emissions

label.

IGNITION SYSTEM (GASOLINE MODELS)

1. This spark ignition system complies with Canadian

ICES-002.

SERVICE AND MAINTENANCE

To avoid personal injury or property damage, use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other

sources of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the

engine running. Allow the engine to cool before

refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where

there is an open flame, spark, or pilot light such

as near a water heater or other appliance.

6. Never fill containers inside a vehicle or on a

truck bed with a plastic bed liner. Always place

containers on the ground away from your vehicle

before filling.

7. Remove gas-powered equipment from the truck

or trailer and refuel it on the ground. If this is not

possible, then refuel such equipment on a trailer

with a portable container, rather than from a

gasoline dispenser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank

or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing

immediately.

10. Never over-fill the fuel tank. Replace gas cap and

tighten securely.

11. Use extra care in handling gasoline and other

fuels. They are flammable and vapors are

explosive.

12. If fuel is spilled, do not attempt to start the engine

but move the machine away from the area of

spillage and avoid creating any source of ignition

until fuel vapors have dissipated.

13. Replace all fuel tank caps and fuel container caps

securely.

Maintenance and Storage

1. Always observe safe refueling and fuel

handling practices when refueling the unit after

transportation or storage.

2. Always follow the engine manual instructions for

storage preparations before storing the unit for

both short and long term periods.

3. Always follow the engine manual instructions for

proper start-up procedures when returning the unit

to service.

4. Never store the machine or fuel container inside

where there is an open flame, such as in a water

heater. Allow unit to cool before storing.

5. Shut off fuel while storing or transporting. Do not

store fuel near flames or drain indoors.

6. Keep all hardware, especially blade attachment

bolts, tight and keep all parts in good working

condition. Replace all worn or damaged decals.

7. Never tamper with safety devices. Check their

proper operation regularly.

8. Disengage drives, lower implement, set parking

brake, stop engine and remove key or disconnect

spark plug wire. Wait for all movement to stop

before adjusting, cleaning or repairing.

9. Clean grass and debris from cutting units, drives,

mufflers, and engine to prevent fires. Clean up oil

or fuel spillage.

10. Let engine cool before storing and do not store

near flame.

11. Stop and inspect the equipment if you strike an

object. Repair, if necessary, before restarting.

12. Park machine on level ground. Never allow

untrained personnel to service machine.

13. Use jack stands to support components when

required.

14. Carefully release pressure from components with

stored energy.

15. Disconnect battery or remove spark plug wire

before making any repairs. Disconnect the

negative terminal first and the positive last.

Reconnect positive first and negative last.

16. Use care when checking blades. Wrap the

blade(s) or wear gloves, and use caution when

servicing them. Only replace blades. Never

straighten or weld them.

17. Keep hands and feet away from moving parts.

If possible, do not make adjustments with the

engine running.

18. Charge batteries in an open well ventilated area,

away from spark and flames. Unplug charger

before connecting or disconnecting from battery.

Wear protective clothes and use insulated tools.

19. Grass catcher components are subject to wear,

damage, and deterioration, which could expose

moving parts or allow objects to be thrown.

Frequently check components and replace

with manufacturer’s recommended parts, when

necessary.

20. Check brake operation frequently. Adjust and

service as required.

21. Use only factory authorized replacement parts

when making repairs.

22. Always comply with factory specifications on all

settings and adjustments.

23. Only authorized service locations should be

utilized for major service and repair requirements.

24. Never attempt to make major repairs on this unit

unless you have been properly trained. Improper

service procedures can result in hazardous

operation, equipment damage and voiding of

manufacturer’s warranty.

25. Units with hydraulic pumps, hoses, or motors:

WARNING: Hydraulic fluid escaping under

pressure may have sufficient force to penetrate

skin and cause serious injury. If foreign fluid is

injected into the skin it must be surgically removed

within a few hours by a doctor familiar with this

form of injury or gangrene may result. Keep body

and hands away from pin holes or nozzles that

eject hydraulic fluid under high pressure. Use

paper or cardboard, and not hands, to search for

Not for

Reproduction

Operator Safety

ROLL BAR INSTRUCTIONS

For models equipped with factory-installed Roll Over

Protection System (ROPS).

OPERATIONAL WARNINGS

• Always use the seat belt when the roll bar is in the

raised position.

• Never use the seat belt when the roll bar is in the

down position.

• Remember there is no roll over protection when

the roll bar is in the down position so it is very

important to always keep the roll bar in the raised

position whenever possible.

• Lower the roll bar to the down position only when

it is absolutely necessary.

• Check for overhead clearances before driving

under any objects. Do not allow roll bar to contact

low overhanging obstacles such as tree branches

and guide wires.

• Never remove the roll bar from the vehicle.

• Do not exceed the machine weight rating of the

roll bar.

• Read and follow all of the instructions shown

below regarding the inspection and maintenance

of the roll bar structure and the seat belt.

INSPECTION OF THE ROLL BAR PROTECTIVE

STRUCTURE

A ROLL BAR, like any other safety device, needs to

be periodically inspected to verify that the integrity of

the device has not been compromised through normal

machine use, misuse, age degradation, modifications,

or a roll over.

WARNING

In order to avoid serious injury or death from

roll over, it is important to follow the warnings

listed below.

WARNING

Failure to properly inspect and maintain the

ROLL BAR protective structure can cause

serious injury or death.

To maintain operator roll over protection and roll bar

effectiveness:

• If a ROLL BAR becomes damaged for any reason,

such as a collision, roll over or impact, the ROLL

BAR must be replaced. Small undetectable

cracks can reduce the effectiveness of the ROLL

BAR. Never weld, straighten, or repair the ROLL

BAR.

• Never alter the ROLL BAR by welding anything to

it or by drilling additional holes.

• BEFORE FIRST TIME USE - Inspect the ROLL

BAR structure and mounting hardware for:

1) Check to make sure the machine GVW (Gross

Vehicle Weight), including attachments,

restrained payload, fuel and operator, is not

in excess of the maximum weight specified on

the ROLL BAR label.

2) Make sure there isn’t any missing, damaged,

or loose mounting hardware.

3) Make sure the ROLL BAR has been correctly

and completely installed.

• EVERY 100 HOURS - Inspect the ROLL BAR

structure and mounting hardware for:

1) Any cracks in the structure (structural members

and/or welds).

2) Significant corrosion on any part of the ROLL

BAR structure or hardware.

3) Missing, damaged, or loose mounting

hardware

4) Mounting hardware that is of a grade lesser

than specified.

5) Machine GVW (Gross Vehicle Weight),

including attachments, restrained payload,

fuel and operator, in excess of the maximum

weight specified on the ROLL BAR label.

6) Any modifications that have been made, such

as unauthorized welds and holes.

7) Any permanent deformation or twisting of the

ROLL BAR structure.

8) That the ROLL BAR label is still in place and is

readable.

9) That the ROLL BAR on-product warning labels

are still on the ROLL BAR and are readable.

• If there is any doubt as to the condition of the

ROLL BAR, remove the machine from service and

contact your dealer for assistance.

leaks. Make sure all hydraulic fluid connections

are tight and all hydraulic hoses and lines are in

good condition before applying pressure to the

system. If leaks occur, have the unit serviced

immediately by your authorized dealer.

26. WARNING: Stored energy device. Improper

release of springs can result in serious personal

injury. Springs should be removed by an

authorized technician.

27. Models equipped with an engine radiator:

WARNING: Stored energy device. To prevent

serious bodily injury from hot coolant or steam

blow-out, never attempt to remove the radiator

cap while the engine is running. Stop the engine

and wait until it is cool. Even then, use extreme

care when removing the cap.

Not for

Reproduction

INSPECT BUCKLE

& LATCH

INSPECT WEBBING

Operator Safety

WARNING

Failure to properly inspect and maintain the

seat belt can cause serious injury or death.

INSPECTION AND MAINTENANCE OF

THE ROLL BAR SEAT BELT

• The seat belt like the ROLL BAR, needs to

be periodically inspected to verify that the

integrity has not been compromised through

normal machine use, misuse, age degradation,

modifications, or a roll over. If the seat belt does

not pass all of the following tests, it should be

replaced.

• BEFORE EACH USE – Conduct the following

inspections/maintenance of the seat belt and

retraction mechanism:

1) Check for dirt or debris in the retraction

mechanism. If dirt or debris is found, it should

be removed.

2) Check to make sure the retraction mechanism

retracts easily and completely.

3) Check for damage to any part of the seat belt

such as nicks, cuts, loose stitching, or fraying.

4) Check that the buckle and latch operate

properly and that the latch plate is not

excessively worn, deformed, or the buckle is

damaged or cracked. The seat belt should

latch and release easily.

Not for

Reproduction

Operator Safety

Safety Decals

This unit has been designed and manufactured to

provide you with the safety and reliability you would

expect from an industry leader in outdoor power

equipment manufacturing.

Although reading this manual and the safety

instructions it contains will provide you with the

necessary basic knowledge to operate this equipment

safely and effectively, we have placed several safety

labels on the unit to remind you of this important

information while you are operating your unit.

All DANGER, WARNING, CAUTION and

instructional messages on your rider and mower

should be carefully read and obeyed. Personal bodily

injury can result when these instructions are not

followed. The information is for your safety and it is

important! The safety decals below are on your rider

and mower.

If any of these decals are lost or damaged, replace

them at once. See your local dealer for replacements.

These labels are easily applied and will act as a

constant visual reminder to you, and others who may

use the equipment, to follow the safety instructions

necessary for safe, effective operation.



Not for

Reproduction

www.ferrisindustries.com

Operator Safety

Safety Interlock System

This unit is equipped with safety interlock switches.

These safety systems are present for your safety,

do not attempt to bypass safety switches, and never

tamper with safety devices. Check their operation

regularly.

Operational SAFETY Checks

Test 1 — Engine should NOT crank if:

• PTO switch is engaged, OR

• Parking brake is not engaged, OR

• Motion control handles are not in the NEUTRAL

position.

Test 2 — Engine SHOULD crank if:

• PTO switch is NOT engaged, AND

• Parking brake is engaged, AND

• Motion control handles are locked in the

NEUTRAL position.

Test 3 — Engine should SHUT OFF if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with parking brake

disengaged.

• Operator moves motion control handles out of

their neutral positions before disengaging parking

brake.

Test 4 — Blade Brake Check

Mower blades and mower drive belt should come

to a complete stop within seven (7) seconds after

electric PTO switch is turned off (or operator rises off

seat). If mower drive belt does not stop within seven

(7) seconds, see your dealer.

NOTE: Once the engine has stopped, PTO switch

must be turned off, parking brake must be engaged,

and the motion control handles must be locked in the

NEUTRAL position after the operator returns to the

seat in order to start the engine.

WARNING

If the unit does not pass a safety test, do not

operate it. See your authorized dealer. Under

no circumstance should you attempt to defeat

the purpose of the safety interlock system.

USA Safety Icons

Alert Toxic Fumes

Read the

Manual

Open Flame

Hazard

Fire Hazard

Amputation -

Rotating Parts

Amputation -

Hand In Blade

Amputation -

Foot In Blade

Thrown Objects Hot Surface

Wear Protective

Gear

Pinch Point

Rollover Hazard

Overhead

Obstacles

Tipover Dropoffs

Slippery Slopes

Keep Children

Away

Rollover

Hazard

Overhead

Obstacles

Not for

Reproduction

Control Functions

The information below briefly describes the function of individual controls. Starting, stopping, driving, and

mowing require the combined use of several controls applied in specific sequences. To learn what combination

and sequence of controls to use for various tasks see the OPERATION section.

Ground Speed Levers

These levers control the ground speed of the rider.

The left lever controls the left rear drive wheel and

the right lever controls the right rear drive wheel.

Moving a lever forward increases the FORWARD

speed of the associated wheel, and pulling back on a

lever increases the REVERSE speed.

Note: The further a lever is moved away from the

neutral position the faster the drive wheel will turn.

See the Operating the Zero Turn Rider section for

steering instructions.

Seat Adjustment Lever

The seat can be adjusted forward and back. Move the

lever towards the left, position the seat as desired,

and release the lever to lock the seat in position.

Ignition Switch

The ignition switch starts and stops the engine, it has

three positions:

OFF Stops the engine and shuts off the

electrical system.

RUN Allows the engine to run and powers

the electrical system.

START Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN

position with the engine stopped–this drains the

battery.

Figure 1. Control Locations

Features and Controls

Features & Controls

Not for

Reproduction

Fuel Tank Cap

To remove the cap, turn counterclockwise.

Fuel Level Gauge

Displays the fuel level in the tank.

www.ferrisindustries.com

Parking Brake

DISENGAGE Releases the parking brake.

ENGAGE Locks the parking brake.

Pull the parking brake lever back to engage the

parking brake. Move the lever fully forward to

disengage the parking brake. NOTE: To start the unit

the parking brake must be engaged.

PTO (Power Take Off) Switch

The PTO switch engages and disengages the mower.

Pull UP on the switch to engage, and push DOWN to

disengage.

Deck Lift Pedal, Cutting

Height Adjustment Pin & Deck Lift Lock

Lever

These control the cutting height of the mower deck.

Depress the pedal until it locks into the 5” (12,7 cm)

position. Place the adjustment pin in the desired

cutting height and release the lift lock lever.

Throttle Control

The throttle controls engine speed. Move the

throttle forward to increase engine speed and back

to decrease engine speed. Always operate at FULL

throttle.

Choke

Close the choke for cold starting. Open the choke

once the engine starts. A warm engine may not

require choking. Pull the knob UP to close the choke.

Push to knob DOWN to open the choke.

Hour Meter

Measures the time of the PTO being engaged. The

hour meter measures the number of hours the PTO

has been engaged. The hour meter has a self

contained power source so the total hours are always

visible.

Features & Controls

Not for

Reproduction

General Operating Safety

Before first time operation:

• Be sure to read all information in the Safety and

Operation sections before attempting to operate

this tractor and mower.

• Become familiar with all of the controls and how to

stop the unit.

• Drive in an open area without mowing to become

accustomed to the unit.

Checks Before Starting

• Check that crankcase is filled to full mark on

dipstick. See the engine Operator’s Manual for

instructions and oil recommendations.

• Make sure all nuts, bolts, screws and pins are in

place and tight.

• Adjust the seat position, and make certain you can

reach all controls from operator’s position.

• Fill the fuel tank with fresh fuel. Refer to engine

manual for fuel recommendations.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any

reason, engage the parking brake, disengage

the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, tractor

and mower free of grass, leaves and excess

grease. Do not stop or park tractor over dry

leaves, grass or combustible materials.

Gasoline is highly flammable and must be

handled with care. Never fill the tank when the

engine is still hot from recent operation. Do not

allow open flame, smoking or matches in the

area. Avoid over-filling and wipe up any spills.

Do not load this zero-turn rider on a trailer or

truck using two separate ramps. Only use

a single ramp that is at least one foot wider

than the width of the rear wheels of this rider.

This rider has a zero turning radius and the

rear wheels could fall off the ramps, or the

rider could tip over injuring the operator or

bystanders.

WARNING

Never operate on slopes greater than 15°.

Select slow ground speed before driving onto

a slope. Use extra caution when operating on

slopes with a rear-mounted grass catcher.

Mow across the face of slopes, not up and

down, use caution when changing directions

and DO NOT START OR STOP ON SLOPE.

WARNING

Operation

Not for

Reproduction

WARNING

If you do not understand how a specific control

functions, or have not yet thoroughly read the

FEATURES & CONTROLS section, do so now.

Do NOT attempt to operate the tractor without

first becoming familiar with the location and

function of ALL controls.

Starting the Engine

1. While sitting in the operator’s seat, engage the

parking brake and make sure the PTO switch is

disengaged and the motion control handles are

locked in the NEUTRAL position.

2. NOTE: A warm engine may not require

choking.

Set the engine throttle control to FAST throttle

position. Then fully close the choke by pulling the

knob OUT fully.

3. Insert the key into the ignition switch and turn it to

START.

4. After the engine starts, gradually open the choke

(push knob down fully). Reduce to half throttle

speed and allow the engine to warm.

Warm up the engine by running it for at least a minute

before engaging the PTO switch or driving the rider.

5. After warming the engine, ALWAYS operate

the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch

to STOP. Use this method only in emergency

situations. For normal engine shut down follow the

procedure given in STOPPING THE RIDER.

Stopping the Rider

1. Returning the ground speed control levers to the

middle position will stop rider movement. Pivot

the levers outward and lock them in NEUTRAL.

2. Disengage the PTO by pushing down on the PTO

switch.

3. Engage the parking brake by pulling the handle up

until it locks into position.

4. Move the throttle control to mid-throttle position

and turn the ignition key to OFF. Remove the

key.

Pushing the Rider by Hand

1. Disengage the PTO, engage the parking brake,

turn the ignition OFF, and remove the key.

2. Lift the seat plate to gain access to the hydraulic

pumps.

3. To disengage the pumps (free-wheel position),

turn the hydraulic release valves (A, Figure 2)

located on the pumps COUNTER-CLOCKWISE a

maximum of 2 full turns.

4. Disengage the parking brake.

The tractor can now be pushed by hand.

5. After moving the tractor, re-engage the pumps

(drive position) by turning the release valves

CLOCKWISE and tighten to 80-120 in. lbs. of

torque.

DO NOT TOW RIDER

Towing the unit will cause hydraulic pump

and wheel motor damage. Do not use

another vehicle to push or pull this unit.

Figure 2. Hydraulic System By-Pass

A. Hydraulic Release Valve

(left-hand pump shown)

www.ferrisindustries.com

Operation

Not for

Reproduction

Operation

Zero-Turn Driving Practice

The lever controls of the Zero Turn rider are

responsive, and learning to gain a smooth and

efficient control of the rider’s forward, reverse, and

turning movements will take some practice.

Spending some time going through the maneuvers

shown and becoming familiar with how the unit

accelerates, travels, and steers — before you begin

mowing —is absolutely essential to getting the most

out of the Zero Turn rider.

Locate a smooth, flat area of your lawn — one

with plenty of room to maneuver. (Clear the area

of objects, people and animals before you begin.)

Operate the unit at mid-throttle during this practice

session (ALWAYS operate at full throttle when

mowing), and turn slowly to prevent tire slippage and

damage to your lawn.

We suggest you begin with the Smooth Travel

procedure to the right, and then advance through the

forward, reverse, and turning maneuvers.

You must release the parking brake prior to moving

the control levers inward.

Forward Travel Practice

Gradually move both ground speed control levers

— evenly FORWARD from neutral. Slow down and

repeat.

NOTE: Straight forward travel takes practice. If

necessary, top speed can be balance-adjusted — see

the Speed Balancing Adjustment in the Adjustments

section near the back of this manual.

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both

ground speed control levers evenly BACK from

neutral. Slow down and repeat.

NOTE: Practice backing up for several minutes before

attempting to do so near objects. The rider turns

sharply in reverse as well as forward, and backing up

straight takes practice.

Figure 4. Forward Travel

Forward

Travel

Figure 5. Reverse Travel

Reverse

Travel

Smooth Travel

The lever controls of

the Zero Turn rider are

responsive.

The BEST method of

handling the ground

speed control levers

is in three steps — as

shown in Figure 3.

FIRST place your

hands onto the levers

as shown.

SECOND, to go

forward gradually push

the levers forward with

your palms.

THIRD, to speed

up move the levers

farther forward. To

slow down smoothly,

slowly move the levers

toward neutral.

Figure 3. Move Control

Levers Gradually

BASIC DRIVING

Not for

Reproduction

ADVANCED DRIVING

Executing an End-Of-Row Zero Turn

Your Zero Turn Rider’s unique ability to turn

in place allows you to turn around at the end

of a cutting row rather than having to stop

and Y-turn before starting a new row.

For example, to execute a left end-of row

zero turn:

1. Slow down at the end of the row.

2. Move the RIGHT ground speed control

lever forward slightly while moving the

LEFT ground speed control lever back

to center and then slightly back from

center.

3. Begin mowing forward again.

This technique turns the rider LEFT

and slightly overlaps the row just cut

—eliminating the need to back up and re-cut

missed grass.

As you become more familiar and

experienced with operating the Zero Turn

rider, you will learn more maneuvers that

will make your mowing time easier and

more enjoyable.

Remember, the more you practice, the

better your control of the Zero Turn will

be!

Practice Turning Around a Corner

While traveling forward allow one handle to gradually

return back toward neutral. Repeat several times.

NOTE: To prevent pivoting directly on the tire tread,

it is best to keep both wheels going at least slightly

forward.

Figure 6. Turning Around a Corner

Figure 7. Turning in Place

Figure 8. Executing an End-Of-Row Turn

Operation

www.ferrisindustries.com

Practice Turning In Place

To turn in place, “Zero Turn,” gradually move one

ground speed control lever forward from neutral and

one lever back from neutral simultaneously. Repeat

several times.

NOTE: Changing the amount each lever is pulled—

forward or back, changes the “pivot point” you turn

on.

Executing

Turns

Turning

In-Place

Not for

Reproduction

Page is loading ...

Ferris 5900832 User manual

Brand: Ferris

Model: 5900832

Category: Lawnmowers

Type: User manual

This manual is also suitable for

Download PDF

report

Ferris 5900832 User manual

This manual is also suitable for

Ferris 5900832 User manual

Related papers

Other documents