Cincoze DE-1000 Series Owner's manual

Power Efficient Fanless Computers

DE-1000

Version: V1.47

Rugged Embedded Computer

DE-1000 Series

User Manual

Power Efficient Fanless Computers

DE-1001

Power Efficient Fanless Computers

DE-1002

DE-1000 Series | User Manual 2

Contents

Preface

Revision……………………………………………..……………….……………...……………...05

Copyright Notice.…………………………………………………………………………………...05

Acknowledgement.……………………………………………………………….........................05

Disclaimer.………………………………………………………………….………………...........05

Declaration of Conformity.………………………………………………….……………………06

Product Warranty Statement …………………………………………………………….............06

Technical Support and Assistance.…………………………………………….…………………07

Conventions Used in this Manual …………………………………………….…………............08

Safety Precaution …...……………………………………………….………….………..............08

Package Contents ………………………………………………………….…….………...……..09

Ordering Information …………………………………...…………………….…….……...……...10

Chapter 1 Product Introductions

1.1 Overview …………………………………………………….……......……………..............12

1.2 Product Pictures…………………………………………….….……....……….….…........12

1.3 Key Features……...……………………………………….…….…….…….….…..............13

1.4 Hardware Specification………….............………………….…………………….…..........14

1.5 System I/O…………………………..……………………….……...………………....……15

1.6 Mechanical Dimension………………………......…………….……………………............21

Chapter 2 Jumpers, Switches and Connectors

2.1 Jumpers Settings ……………………………….………………………………...………….25

2.2 Location of the Jumpers/Switches/Connectors.………………………………...…………25

2.2.1 Top View ……………………………….……………………………………...………..25

2.2.2 Bottom View ……………………………………………………………...……............26

2.3 Definition of Jumpers/Switches/Connectors………..….………………………………......27

2.4 Definition of Jumpers.……...……………..............................................……..................28

2.5 Definition of Switches….…...….……...……….............……………….............................29

2.6 Definition of Connectors …...….……...……….............…..………….............................31

Chapter 3 System Setup

3.1 Remove the Chassis Bottom Cover………………………….….…………………..........41

3.2 Removing the Chassis…………………………………………………….………………….42

3.3 Installing a Half Size Mini PCIe Card on Upper Side………....…………….……………43

3.4 Installing a Full Size Mini PCIe Card on Upper Side.…….……...……………….............45

3.5 Installing Antenna………………………………………..........….…………………............47

DE-1000 Series | User Manual 3

3.6 Installing a SATA Hard Drive on Upper Side…………………………………....…………49

3.7 Installing a SATA Hard Drive on Bottom Side.……....………...….…………………...…51

3.8 Installing SO-DIMM 1…...…………………….….……………..........................................52

3.9 Installing SO-DIMM 2…………………………...……………....….…………….……….....54

3.10 Installing Half Size Mini PCIe Card on Bottom Side……………...….……………………57

3.11 Installing Full Size Mini PCIe Cards on Bottom Side…………….………………........….59

3.12 Installing the PCI/PCIe Cards on Expansion Module (DE-1001 and DE-1002 Only)..62

3.13 Installing the Chassis………………………….………...…………….……………............65

3.14 Installing the Chassis Bottom Cover……...……….………...….………………………..66

3.15 Installing a SIM Card….…….….…….……………...….…………………………...………67

3.16 Installing a CFast Card….…….….…….……………...….…………………………...……68

3.17 Wall Mount Bracket….…….….…….……………...….……………………..………...……69

Chapter 4 BIOS Setup

4.1 BIOS Introduction …….……….…………….…….…..….……………………...................72

4.2 Main Setup ……...……….…..……………….…..….………………........…………...........73

4.2.1 System Date …….……………………………………………...…………….............73

4.2.2 System Time ………..……………………………………………..……….................73

4.3 Advanced Setup ……………………………………………………………………………...74

4.3.1 ACPI Setting ………………...………………………………………………………….74

4.3.2 Super IO Configuration...……………………………………………………………...75

4.3.3 Hardware Monitor……………………………………………………………...……….76

4.3.4 Serial Port Console Redirection……………...……………………….…................77

4.3.5 CPU Configuration…..………………………………………….…………………....77

4.3.6 PPM Configuration…………………………………………………………………....78

4.3.7 Thermal Configuration……………………………………….....………….................79

4.3.8 IDE Configuration…..…………………………..……………………..…………….....80

4.3.9 OS Selection………………………………………………………………………......80

4.3.10 CSM (Compatibility Support Module) Configuration……………….……..….....81

4.3.11 USB Configuration………….…………………………………………………..........82

4.4 Chipset Setup …...……….…………………..…..….…..…………………………………...83

4.4.1 North Bridge……………………………………..……………………………………..83

4.4.2 South Bridge………….………………….……………………………………………..85

4.5 Security Setup …...……….………………….…..…….…………..……………………...…87

4.5.1 Administrator Password …….…...……………………………………………………87

4.5.2 User Password …….…………………………………………………..………………87

4.6 Boot Setup …...……….….……………………………...…..….…..………..…………....…88

4.6.1 Setup Prompt Timeout………………………….……………………………………..88

4.6.2 Bootup NumLock State…………………..……………………………………………88

DE-1000 Series | User Manual 4

4.6.3 Full Screen Logo Show………………………...……………….………………..……88

4.6.4 Fast Boot ……………..………………………………………………………………...88

4.7 Save & Exit …...……….….…………………. …..….…..……………………….................89

4.7.1 Save Changes and Reset …………………………………………………………….89

4.7.2 Discard Changes and Reset ….………………………………………………………89

4.7.3 Restore Defaults …………………………………….…………………………………89

4.7.4 Save as User Defaults …………………..…………………………………………….89

4.7.5 Restore User Defaults ..…………………………….…………………………………89

Chapter 5 Product Application

5.1 Digital I/O (DIO) application ………..…………………………………………………………91

5.1.1 Digital I/O Programming Guide ……………………………………………………..91

5.2 DE-1000 Digital I/O (DIO) Hardware Specification ………………………………….……..97

DE-1000 Series | User Manual 5

Preface

Revision

Description

Date

1.00

First Release

2015/01/12

1.10

DIO PIN Define Revision

2015/05/08

1.20

Content corrected, product pictures updated, CH. 5

added

2016/06/20

1.30

Add 1.2 support dimension of add-on card

2017/06/21

1.40

Correction Made

2018/11/20

1.41

Correction Made

2020/04/09

1.42

New Format Updated

2020/10/22

1.43

LVD Number Updated

2021/02/08

1.44

Add DC_IN1 Warning

2021/04/20

1.45

Correction Made

2021/06/28

1.46

Correction Made

2022/05/31

1.47

Correction Made

2023/04/14

Copyright Notice

modified, or reproduced in any form or by any means for commercial use without the prior

written permission of Cincoze Co., Ltd. All information and specification provided in this

manual are for reference only and remain subject to change without prior notice.

Acknowledgement

Cincoze is a registered trademark of Cincoze Co., Ltd. All registered trademarks and product

names mentioned herein are used for identification purposes only and may be trademarks

and/or registered trademarks of their respective owners.

Disclaimer

This manual is intended to be used as a practical and informative guide only and is subject

to change without notice. It does not represent a commitment on the part of Cincoze. This

product might include unintentional technical or typographical errors. Changes are

periodically made to the information herein to correct such errors, and these changes are

incorporated into new editions of the publication.

DE-1000 Series | User Manual 6

Declaration of Conformity

FCC

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

CE

The product(s) described in this manual complies with all application European

Union (CE) directives if it has a CE marking. For computer systems to remain

CE compliant, only CE-compliant parts may be used. Maintaining CE

compliance also requires proper cable and cabling techniques.

Product Warranty Statement

Warranty

Cincoze products are warranted by Cincoze Co., Ltd. to be free from defect in materials and

workmanship for 2 years from the date of purchase by the original purchaser. During the

warranty period, we shall, at our option, either repair or replace any product that proves to be

defective under normal operation. Defects, malfunctions, or failures of the warranted product

caused by damage resulting from natural disasters (such as by lightening, flood, earthquake,

etc.), environmental and atmospheric disturbances, other external forces such as power line

disturbances, plugging the board in under power, or incorrect cabling, and damage caused

by misuse, abuse, and unauthorized alteration or repair, and the product in question is either

software, or an expendable item (such as a fuse, battery, etc.), are not warranted.

RMA

Before sending your product in, you will need to fill in Cincoze RMA Request Form and

obtain a RMA number from us. Our staff is available at any time to provide you with the most

friendly and immediate service.

◼ RMA Instruction

⚫ Customers must fill in Cincoze Return Merchandise Authorization (RMA)

Request Form and obtain an RMA number prior to returning a defective

product to Cincoze for service.

DE-1000 Series | User Manual 7

⚫ Customers must collect all the information about the problems encountered

and note anything abnormal and describe the problems on the “Cincoze

Service Form” for the RMA number apply process.

⚫ Charges may be incurred for certain repairs. Cincoze will charge for repairs to

products whose warranty period has expired. Cincoze will also charge for

repairs to products if the damage resulted from acts of God, environmental or

atmospheric disturbances, or other external forces through misuse, abuse, or

unauthorized alteration or repair. If charges will be incurred for a repair,

Cincoze lists all charges, and will wait for customer’s approval before

performing the repair.

⚫ Customers agree to ensure the product or assume the risk of loss or damage

during transit, to prepay shipping charges, and to use the original shipping

container or equivalent.

⚫ Customers can be sent back the faulty products with or without accessories

(manuals, cable, etc.) and any components from the system. If the

components were suspected as part of the problems, please note clearly

which components are included. Otherwise, Cincoze is not responsible for the

devices/parts.

⚫ Repaired items will be shipped along with a "Repair Report" detailing the

findings and actions taken.

Limitation of Liability

Cincoze’ liability arising out of the manufacture, sale, or supplying of the product and its use,

whether based on warranty, contract, negligence, product liability, or otherwise, shall not

exceed the original selling price of the product. The remedies provided herein are the

customer’s sole and exclusive remedies. In no event shall Cincoze be liable for direct,

indirect, special or consequential damages whether based on contract of any other legal

theory.

Technical Support and Assistance

1. Visit the Cincoze website at www.cincoze.com where you can find the latest information

about the product.

2. Contact your distributor or our technical support team or sales representative for

technical support if you need additional assistance. Please have following information

ready before you call:

⚫ Product name and serial number

⚫ Description of your peripheral attachments

⚫ Description of your software (operating system, version, application software, etc.)

⚫ A complete description of the problem

⚫ The exact wording of any error messages

DE-1000 Series | User Manual 8

Conventions Used in this Manual

Safety Precautions

Before installing and using this device, please note the following precautions.

1. Read these safety instructions carefully.

2. Keep this User’s Manual for future reference.

3. Disconnected this equipment from any AC outlet before cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equipment and

must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall

may cause damage.

7. Make sure the voltage of the power source is correct before connecting the equipment

to the power outlet.

8. Use a power cord that has been approved for using with the product and that it matches

the voltage and current marked on the product’s electrical range label. The voltage and

current rating of the cord must be greater than the voltage and current rating marked on

the product.

9. Position the power cord so that people cannot step on it. Do not place anything over the

power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid

DE-1000 Series | User Manual 9

damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only

by qualified service personnel.

If one of the following situations arises, get the equipment checked by service

personnel:

⚫ The power cord or plug is damaged.

⚫ Liquid has penetrated into the equipment.

⚫ The equipment has been exposed to moisture.

⚫ The equipment does not work well, or you cannot get it work according to the user's

manual.

⚫ The equipment has been dropped and damaged.

⚫ The equipment has obvious signs of breakage.

14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the

same or equivalent type recommended by the manufacturer.

15. Equipment intended only for use in a RESTRICTED ACCESS AREA.

DE-1000 Series | User Manual 10

Package Contents

Before installation, please ensure all the items listed in the following table are included in the

package.

Item

Description

Q’ty

1

DE-1000 / DE-1001 / DE-1002 Embedded System

1

2

DIO Terminal Block Connector

2

3

Power Terminal Block Connector

1

4

Remote Power Terminal Block Connector

2

5

DVI-I to VGA Adaptor

1

6

Screws Pack

1

7

Wall Mount Kit

1

Note: Notify your sales representative if any of the above items are missing or damaged.

Ordering Information

Model No.

Product Description

DE-1000

Intel Atom E3845 Quad Core Power Efficient Fanless Computer

DE-1001-E

Intel Atom E3845 Quad Core Power Efficient Fanless Computer

with 1x PCIex1 Expansion

DE-1001-P

Intel Atom E3845 Quad Core Power Efficient Fanless Computer

with 1x PCI Expansion

DE-1002-EE

Intel Atom E3845 Quad Core Power Efficient Fanless Computer

with 2x PCIex1 Expansions

DE-1002-PP

Intel Atom E3845 Quad Core Power Efficient Fanless Computer

with 2x PCI Expansions

DE-1000 Series | User Manual 11

Chapter 1

Product

Introductions

DE-1000 Series | User Manual 12

1.1 Overview

DE-1000 Series Fanless Embedded PC supports Intel® Bay Trail platform, integrated with Intel®

Atom™ E3845 Quad Core 1.91 GHz processor. Delivering the excellent quad-core processing power

at only 10 watts power consumption, DE-1000 series is definitely an ideal solution for ultimate

computing performance, energy efficiency, and superior reliability.

Designed with rich I/O, high flexibility and easy expansion capabilities, DE-1000 series is ideal for

diverse industrial applications. It offers multiple I/O extension modules, including up to 2x PCI or 2x

PCIe x1 slot for flexible integration of a variety of add-on cards; 2x mini-PCIe slot for GSM and WLAN

wireless communication; it also supports three storage expansions: 2.5” SATA HDD, CFast and SIM

card.

Supporting up to 6x LAN or 4x PoE versions, and power ignition function, DE-1000 series can meet

various applications, such as: surveillance, in-vehicle, and industrial automation applications, etc.

DE-1000 series supports wide temperature range from -25°C to +70°C, wide range 9-48VDC power

input, power protection, cable-less and one-piece housing design, as well as compliant with

EN50155 certification for rail transportation applications; it is designed to ensure stable operation in

robust and harsh environments.

1.2 Product pictures

DE-1000

DE-1001

DE-1002

Front

Rear

DE-1000 Series | User Manual 13

1.3 Key Features

⚫ Onboard Intel® Atom™ E3845 Processor Quad Core, 1.91GHz

⚫ 2x DDR3L SO-DIMM Max. up to 8GB

⚫ Dual Independent Display from 1x DVI-I and 1x DisplayPort

⚫ 2x Intel® GbE Port, Support Wake-on-LAN and PXE (DE-1000, DE-1001, DE-1002

Only)

⚫ 1x USB 3.0, 4x USB 2.0

⚫ 6x RS232/422/485 Port with 5V/12V Power

⚫ 4x Isolated DI, 4x Isolated DO

⚫ 2x 2.5” SATA SSD/HDD Bay, 1x mSATA (Shared by Mini-PCIe Socket) , 1x CFast Card

and 1x SIM Card Socket

⚫ 9-48VDC Power Input, support AT/ATX Mode

⚫ 2x Mini-PCIe Slot for Wi-Fi, GSM, or I/O Expansion

⚫ 1x PCI or 1x PCIe x1 Expansion (DE-1001)

⚫ 2x PCI or 2x PCIe x1 Expansion (DE-1002)

⚫ Power Ignition

⚫ EN50155 (EN50121-3-2) / EN62368-1 Certified

DE-1000 Series | User Manual 14

1.4 Hardware Specification

Processor

• Onboard Intel® Atom™ Processor E3845 Quad Core, 1.91

GHz with AMI 64Mbit SPI BIOS

Memory

• 2x 204-Pin DDR3L-1066 / 1333MHz SO-DIMM

(un-buffered and non-ECC), Max. up to 8GB

Display

Dual Display

• 1x DVI and 1x DisplayPort

• 1x DVI-D and 1x VGA (w/ Optional Split Cable)

• 1x DisplayPort and 1x VGA (w/ DVI-I to VGA Adapter)

Ethernet

• 2x Intel® I210 GbE LAN Port, Support Wake-on-LAN and

PXE

Audio Codec

• Codec: Realtek ALC888S

• 1x Mic-in and 1x Line-out

Watchdog Timer

• Software Programmable Supports 256 Levels System

Reset

Storage

• 2x 2.5” SATA HDD Bay

• 1x Internal mSATA Slot (Shared by Mini-PCIe Socket)

• 1x External CFast Socket

• 1x External SIM Card Socket

I/O Interface

• 1x USB 3.0 Port

• 4x USB 2.0 Port

• 8x Optical Isolated DIO (4xDI, 4xDO), 10 Pin Terminal

Block Support 9-30V

• 6x DB9 for COM1~6, Support RS-232/422/485 with Auto

Flow Control

• 1x PS/2 Port

• 2x Antenna Hole

• 1x Power Switch

• 1x AT/ATX Switch

• 1x Remote Power and Reset Connector

Power Requirement

• Support AT, ATX Mode

• 1x 3-pin Terminal Block Connector with Power Input

9-48VDC

• 1x Optional AC/DC 12V/5A, 60W Power Adapter

• 1x Optional AC/DC 24V/5A, 120W Power Adapter

Expansion

• DE-1001-E:

✓ 1x PCIe x1

Support maximum dimension of add-on card (H x L):

111.15mm x 174.63mm

• DE-1001-P:

✓ 1x PCI

Support maximum dimension of add-on card (H x L):

111.15mm x 174.63mm

• DE-1002-EE:

✓ 2x PCIe x1

Support maximum dimension of add-on card (H x L):

111.15mm x 174.63mm

• DE-1002-PP:

✓ 2x PCI

Support maximum dimension of add-on card (H x L):

111.15mm x 174.63mm

• 2x Full-size Mini PCIe Socket for Wi-Fi / GSM /

Expansion Module

• 1x Universal I/O Bracket (DE-1001)

• 2x Universal I/O Bracket (DE-1002)

Physical

• DE-1000

- Dimension (WxDxH): 203 x 200 x 65 mm

- Weight: 2.84 kg

• DE-1001

- Dimension (WxDxH): 203 x 200 x 96.5 mm

- Weight: 3.42 kg

• DE-1002

- Dimension (WxDxH): 203 x 200 x 114.5 mm

- Weight: 3.76 kg

• Construction: Extruded Aluminum with Heavy Duty Metal

• Mounting: Wall Mounting (Side / VESA / DIN-Rail)

Protection

• Reverse Power Input Protection

• Over Voltage Protection

- Protection Range: 51-58V

- Protection Type: shut down operating voltage, re-power

on at the present level to recover

• Over Current Protection: 15A

• ESD Protection: +/-8kV (air), +/-4kV (contact)

• Surge Protection: 2 kV

Operating System

• Windows® 10/ 8/ Embedded 8 Standard/ 7/ Embedded

Standard 7

• Linux®: Supports by project

Environment

• Operating Temperature: Ambient with Air Flow:

-25°C to 70°C (with Industrial Grade Peripherals)

• Storage Temperature: -30°C to 85°C

• Relative humidity: 10%~95% (non-condensing)

• Shock: 50 Grms

(According to IEC 60068-2-27, Half Sine, 11ms Duration)

• Vibration: Random: 5 Grms

(According to IEC 60068-2-64, 5~500Hz, 1hr/axis)

Certification

• CE

• FCC Class A

• EN 50155

• EN 50121-3-2

• LVD EN62368-1

DE-1000 Series | User Manual 15

1.5 System I/O

1.5.1 DE-1000

Front Panel

ATX Power On/Off

Used to power-on or power-off the system

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

USB2.0

Used to connect to USB 2.0/1.1 compatible

devices

AT/ATX Mode Select Switch

Used to select AT or ATX power mode

CFast and SIM Card Slot

Used to insert a CFast card and a SIM card

COM Port

Used to connect to RS-232/422/485 serial

devices

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 isolated

DIO (4 digital input and 4 digital output)

DE-1000 Series | User Manual 16

Rear Panel

DC IN

Used to plug a DC power input with terminal

block

DVI-I Port

Used to connect a DVI monitor or connect

optional split cable for dual display mode

PS/2 Port

Used to connect the PS/2 device

LAN Port (1~2)

Used to connect to local area network

USB3.0

Used to connect to USB 3.0/2.0/1.1 compatible

devices

USB2.0

Used to connect to USB 2.0/1.1 compatible

devices

Display Port

Used to connect a monitor with DisplayPort

interface

Antenna Hole

Used to connect an antenna for optional wireless

module

COM Port

Used to connect to RS-232/422/485 serial

devices

Mic-In

Used to connect a microphone

Line-Out

Used to connect a speaker

Remote Power On/Off and Remote Power

Reset Terminal Block

A terminal block used to connect to a remote

power on/off switch and a remote power reset

switch

DE-1000 Series | User Manual 17

1.5.2 DE-1001

Front Panel

ATX Power On/Off

Used to power-on or power-off the system

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

USB2.0

Used to connect to USB 2.0/1.1 compatible

devices

AT/ATX Mode Select Switch

Used to select AT or ATX power mode

CFast and SIM Card Slot

Used to insert a CFast card and a SIM card

COM Port

Used to connect to RS-232/422/485 serial

devices

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 isolated

DIO (4 digital input and 4 digital output)

DE-1000 Series | User Manual 18

Rear Panel

DC IN

Used to plug a DC power input with terminal

block

DVI-I Port

Used to connect a DVI monitor or connect

optional split cable for dual display mode

PS/2 Port

Used to connect the PS/2 device

LAN Port (1~2)

Used to connect to local area network

USB3.0

Used to connect to USB 3.0/2.0/1.1 compatible

devices

USB2.0

Used to connect to USB 2.0/1.1 compatible

devices

Display Port

Used to connect a monitor with DisplayPort

interface

Antenna Hole

Used to connect an antenna for optional wireless

module

COM Port

Used to connect to RS-232/422/485 serial

devices

Mic-In

Used to connect a microphone

Line-Out

Used to connect a speaker

Remote Power On/Off and Remote Power

Reset Terminal Block

A terminal block used to connect to a remote

power on/off switch and a remote power reset

switch

Universal I/O Bracket

Used to customized I/O output with optional

modules

DE-1000 Series | User Manual 19

1.5.3 DE-1002

Front Panel

ATX Power On/Off

Used to power-on or power-off the system

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

USB2.0

Used to connect to USB 2.0/1.1 compatible

devices

AT/ATX Mode Select Switch

Used to select AT or ATX power mode

CFast and SIM Card Slot

Used to insert a CFast card and a SIM card

COM Port

Used to connect to RS-232/422/485 serial

devices

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 isolated

DIO (4 digital input and 4 digital output)

DE-1000 Series | User Manual 20

Rear Panel

DC IN

Used to plug a DC power input with terminal

block

DVI-I Port

Used to connect a DVI monitor or connect

optional split cable for dual display mode

PS/2 Port

Used to connect the PS/2 device

LAN Port (1~2)

Used to connect to local area network

USB3.0

Used to connect to USB 3.0/2.0/1.1 compatible

devices

USB2.0

Used to connect to USB 2.0/1.1 compatible

devices

Display Port

Used to connect a monitor with DisplayPort

interface

Antenna Hole

Used to connect an antenna for optional wireless

module

COM Port

Used to connect to RS-232/422/485 serial

devices

Mic-In

Used to connect a microphone

Line-Out

Used to connect a speaker

Remote Power On/Off and Remote Power

Reset Terminal Block

A terminal block used to connect to a remote

power on/off switch and a remote power reset

switch

Universal I/O Bracket

Used to customized I/O output with optional

modules

Page is loading ...

Cincoze DE-1000 Series Owner's manual

Cincoze DE-1000 Series Owner's manual

Related papers

Other documents