Skyjacker SBE320 Installation guide

Skyjacker
Brand
Skyjacker
Model
SBE320
Type
Installation guide

This manual is also suitable for

Skyjacker SBE320 is a double disconnect sway bar end link designed to provide increased articulation and off-road performance. It features a durable construction with polyurethane bushings and a metal sleeve for long-lasting performance. The SBE320 is easy to install and can be used on both the outboard and inboard sides of the axle bracket. It is compatible with a wide range of vehicles and can help improve handling and stability, both on and off-road.

Skyjacker SBE320 is a double disconnect sway bar end link designed to provide increased articulation and off-road performance. It features a durable construction with polyurethane bushings and a metal sleeve for long-lasting performance. The SBE320 is easy to install and can be used on both the outboard and inboard sides of the axle bracket. It is compatible with a wide range of vehicles and can help improve handling and stability, both on and off-road.

Remove the sway bar end link's lower
bolt at axle housing on both sides (see picture
#1). Remove top of sway bar endlink and dis-
card.
NOTE: Sway bar end must be drilled or
filed to allow clearance for the provided 7/16" x
1 1/2" bolt (see arrow in photo #2). The new
end link mounting bracket should be mounted
to the bottom of the sway bar with the bolt
pointing up through the sway bar and the nut
and 7/16 USS washer applied on top
(see picture 2). Apply lithium grease to the
polyurethane bushings. Insert them into the
end link eyes along with the metal sleeve (#54314). The top 1/2" x 2 1/2" bolt connecting the bracket to the end
link must be installed with the nut to the outside of the vehicle to provide adequate clearance to the frame. Install
new double disconnect end links on the inboard side of the axle bracket, being sure that the offset is turned
inward.(see picture #3).
DOUBLE DISCONNECT
SWAY BAR ENDLINKS
INSTALLATION INSTRUCTIONS
Part # SBE120/124/320
Picture #1 Picture #2 Picture #3
Remove the sway bar end link's lower bolt
at axle housing on both sides (see picture #1).
Remove top of sway bar endlink and discard.
NOTE: Sway bar end must be drilled or
filed to allow clearance for the provided 7/16" x
1 1/2" bolt (see arrow in photo #2). The new
end link mounting bracket should be mounted
to the bottom of the sway bar with the bolt
pointing up through the sway bar and the nut
and 7/16 USS washer applied on top
(see picture 2). Apply lithium grease to the
polyurethane bushings. Insert them into the
end link eyes along with the metal sleeve (#54314). The top 1/2" x 2 1/2" bolt connecting the bracket to the end
link must be installed with the nut to the outside of the vehicle to provide adequate clearance to the frame. Install
new double disconnect end links on the inboard side of the axle bracket, being sure that the offset is turned
inward.(see picture #3).
DOUBLE DISCONNECT
SWAY BAR ENDLINKS
INSTALLATION INSTRUCTIONS
Part # SBE120/124/320
Picture #1
I-SBE120/124 (3/02)
I-SBE120/124 (3/02)
Picture #2 Picture #3
Outboard
Outboard
  • Page 1 1

Skyjacker SBE320 Installation guide

Skyjacker
Brand
Skyjacker
Model
SBE320
Type
Installation guide
This manual is also suitable for

Skyjacker SBE320 is a double disconnect sway bar end link designed to provide increased articulation and off-road performance. It features a durable construction with polyurethane bushings and a metal sleeve for long-lasting performance. The SBE320 is easy to install and can be used on both the outboard and inboard sides of the axle bracket. It is compatible with a wide range of vehicles and can help improve handling and stability, both on and off-road.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents