Gigabyte GA-8I915P-D Pro Owner's manual

GA-8I915P-D Pro

Intel® Pentium® 4 LGA775 Processor Motherboard

User's Manual

Rev. 2003

12ME-8I915PDP-2003

Motherboard

GA-8I915P-D Pro

Jun. 11, 2004

Motherboard

GA-8I915P-D Pro

Copyright

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

nFor quick installation, please refer to the "Hardware Installation Guide" included with the

product.

nFor detailed product information and specifications, please carefully read the

"Product User Manual".

nFor detailed information related to Gigabyte's unique features, please go to "Technology

Guide" section on Gigabyte's website to read or download the information you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

- 4 -

Table of Contents

GA-8I915P-D Pro Motherboard Layout ......................................................................6

Block Diagram...........................................................................................................7

Chapter 1 Hardware Installation.................................................................................9

1-1Considerations Prior to Installation ..................................................................... 9

1-2Feature Summary............................................................................................... 10

1-3Installation of the CPU and Heatsink................................................................ 12

1-3-1Installation of the CPU.....................................................................................12

1-3-2Installation of the Heatsink...............................................................................13

1-4Installation of Memory........................................................................................ 14

1-5Installation of Expansion Cards......................................................................... 16

1-6I/O Back Panel Introduction............................................................................... 17

1-7Connectors Introduction ..................................................................................... 18

Chapter 2 BIOS Setup ...........................................................................................29

The Main Menu (For example: BIOS Ver. : F3c)......................................................... 30

2-1Standard CMOS Features.................................................................................. 32

2-2Advanced BIOS Features.................................................................................. 34

2-3Integrated Peripherals........................................................................................ 36

2-4Power Management Setup................................................................................. 39

2-5PnP/PCI Configurations..................................................................................... 41

2-6PC Health Status................................................................................................. 42

2-7MB Intelligent Tweaker(M.I.T.).......................................................................... 43

2-8Select Language ................................................................................................. 45

2-9 Load Fail-Safe Defaults...................................................................................... 45

2-10 Load Optimized Defaults.................................................................................... 46

2-11 Set Supervisor/User Password......................................................................... 46

2-12 Save & Exit Setup............................................................................................... 47

2-13 Exit Without Saving............................................................................................. 47

- 5 -

Chapter 3 Install Drivers.........................................................................................49

3-1Install Chipset Drivers........................................................................................ 49

3-2Software Applications......................................................................................... 50

3-3Driver CD Information......................................................................................... 50

3-4Hardware Information ......................................................................................... 51

3-5Contact Us........................................................................................................... 51

Chapter 4 Appendix...............................................................................................53

4-1Unique Software Utilities.................................................................................... 53

4-1-1Xpress Recovery Introduction ..........................................................................54

4-1-2Flash BIOS Method Introduction ......................................................................57

4-1-3 2- / 4- / 6- / 8- Channel Audio Function Introduction.........................................68

4-2Troubleshooting................................................................................................... 73

- 6 -

GA-8I915P-D Pro Motherboard Layout

KB_MSATX_12V

CPU_FAN

LGA775

SPDIF_O

COMA LPT

USB

LAN

IR

BAT

TSB43AB23

Marvell

8001

CD_IN

AZALIA_FP

Intel 915P

NB_FAN

AUDIO1

S_ATA0

ICH6

Main

BIOSBackup

BIOSPCI1

PCI2

DDRII1

DDRII2

DDRII3

DDRII4

ATX

PWR_FAN

IDE

SYS_FAN

S_ATA3

S_ATA2

S_ATA1

FDD

PWR_LED

F_PANEL

CLR_CMOS

F1_1394

F2_1394

PCIE_16

PCIE_1

PCIE_2

PCIE_3

F_USB2

F_USB1

IT8712

CODEC

R_USB

GA-8I915P-D Pro

SPDIF_I

AUDIO2

- 7 -

Block Diagram

Line-Out

MIC

Center/Subwoofer Speaker Out

LGA775

Processor

CPUCLK+/-(200/133MHz)

PCI Express x16

33MHz

Host

Interface

Intel

915P

MCH MCHCLK (133/200MHz)

66MHz

48MHz

DDRII 600(Note)/533/400MHz DIMM

Dual Channel Memory

COM Port

Floppy

PS/2 KB/Mouse

24MHz

33MHz

IT 8712

4 Serial ATA

ATA33/66/100

IDE Channels

Intel

ICH6

14.318MHz

Dual BIOS

8 USB

Ports

CODEC

Line-In

PCI Express x1 Bus

PCICLK

(33MHz)

2 PCI

PCI Bus

Marvell

8001

RJ45

3 IEEE1394

TSB43AB23

SPDIF In

SPDIF Out

LPT Port

3 PCI Express x 1 Ports

Side Speaker Out

Surround Speaker Out

PCI-ECLK

(100MHz)

PCI-ECLK

(100MHz)

(Note)To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB

processor and overclock in BIOS.

- 8 -

Hardware Installation- 9 -

English

1-1Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please

follow the instructions below:

1.Please turn off the computer and unplug its power cord.

2.When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).

4.Prior to installing the electronic components, please have these items on top of an antistatic pad or

within a electrostatic shielding container.

5.Please verify that you the power supply is switched off before unplugging the power supply connector

from the motherboard.

Installation Notices

1.Prior to installation, please do not remove the stickers on the motherboard. These stickers are required

for warranty validation.

2.Prior to the installation of the motherboard or any hardware, please first carefully read the information

in the provided manual.

3.Before using the product, please verify that all cables and power connectors are connected.

4.To prevent damage to the motherboard, please do not allow screws to come in contact with the

motherboard circuit or its components.

5.Please make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

6.Please do not place the computer system on an uneven surface.

7.Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product,

please consult a certified computer technician.

Instances of Non-Warranty

1.Damage due to natural disaster, accident or human cause.

2.Damage as a result of violating the conditions recommended in the user manual.

3.Damage due to improper installation.

4.Damage due to use of uncertified components.

5.Damage due to use exceeding the permitted parameters.

6.Product determined to be an unofficial Gigabyte product.

Chapter 1 Hardware Installation

GA-8I915P-D Pro Motherboard- 10 -

English

CPUwSupports the latest Intel® Pentium® 4 LGA775 CPU

wSupports 800/533MHz FSB

wL2 cache varies with CPU

ChipsetwNorthbridge: Intel® 915P Express Chipset

wSouthbridge: Intel® ICH6

Memoryw4 DDR II DIMM memory slots (supports up to 4GB memory) (Note 1)

wSupports dual channel DDR II 600(Note 2)/533/400 DIMM

wSupports 1.8V DDR II DIMM

Slotsw1 PCI Express x 16 slot

w3 PCI Express x 1 slots

w2 PCI slots

IDE Connectionsw1 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of 2

IDE devices

FDD Connectionsw1 FDD connection, allows connection of 2 FDD devices

Onboard SATAw4 Serial ATA connections

Peripheralsw1 parallel port supporting Normal/EPP/ECP mode

w1 Serial port (COMA)

w8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)

w3 IEEE1394 ports (requires cable)

w1 front audio connector

w1 IR connector

w1 PS/2 keyboard port

w1 PS/2 mouse port

Onboard LANwOnboard Marvell 8001 chip (10/100/1000 Mbit)

w1 RJ 45 port

Onboard AudiowALC880 CODEC

wSupports Jack Sensing function

wSupports 2 / 4 / 6 / 8 channel audio

wSupports Line In ; Line Out (Front Speaker Out) ; MIC ; Surround Speaker Out

(Rear Speaker Out) ; Center/Subwoofer Speaker Out ;

Side Speaker Out connection

wSupports SPDIF In/Out connection

wCD In

I/O ControlwIT8712

(Note 1)Due to standard PC architecture, a certain amount of memory is reserved for system usage and

therefore the actual memory size is less than the stated amount.

For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup.

(Note 2)To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB

processor and overclock in BIOS.

1-2Feature Summary

Hardware Installation- 11 -

English

Hardware MonitorwSystem voltage detection

wCPU temperature detection

wCPU / System / Power fan speed detection

wCPU warning temperature

wCPU / System / Power fan failure warning

wCPU smart fan control

BIOSwUse of licensed AWARD BIOS

wSupports Dual BIOS/Q-Flash/Multilanguage

Additional FeatureswSupports @BIOS

wSupports EasyTune

Overclocking wOver Voltage via BIOS (CPU/DDR II/PCI-E)

wOver Clock via BIOS (CPU/DDR II)

Form FactorwATX form factor; 30.5cm x 24.4cm

GA-8I915P-D Pro Motherboard- 12 -

English

1-3Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:

1.Please make sure that the motherboard supports the CPU.

2.Please take note of the one indented corner of the CPU. If you install the CPU in the wrong

direction, the CPU will not insert properly. If this occurs, please change the insert direction

of the CPU.

3.Please add an even layer of heat sink paste between the CPU and heatsink.

4.Please make sure the heatsink is installed on the CPU prior to system use, otherwise

overheating and permanent damage of the CPU may occur.

5.Please set the CPU host frequency in accordance with the processor specifications. It is not

recommended that the system bus frequency be set beyond hardware specifications since it

does not meet the required standards for the peripherals. If you wish to set the frequency

beyond the proper specifications, please do so according to your hardware specifications

including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all

of the following platform components:

- CPU: An Intel® Pentium 4 Processor with HT Technology

- Chipset: An Intel® Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1Installation of the CPU

Fig. 1

Gently lift the metal

lever located on the

CPU socket to the

upright position.

Metal LeverFig. 2

Remove the plastic

covering on the CPU

socket.

Fig. 3

Notice the small gold

colored triangle located

on the edge of the CPU

socket. Align the

indented corner of the

Fig. 4

Once the CPU is

properly inserted,

please replace the

plastic covering and

push the metal lever

back into its original

position.

CPU with the triangle and gently insert the CPU into

position. (Grasping the CPU firmly between your

thumb and forefinger, carefully place it into the socket

in a straight and downwards motion. Avoid twisting or

bending motions that might cause damage to the CPU

during installation.)

Hardware Installation- 13 -

English

1-3-2Installation of the Heatsink

The heatsink may adhere to the CPU as a result of hardening of the heatsink paste.To prevent

such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for

heat dissipation or using extreme care when removing the heatsink.

Fig. 6

Finally, please attach the power connector of the

heatsink to the CPU fan header located on the

motherboard.

Fig. 3

Place the heatsink atop the CPU and make sure

the push pins aim to the pin hole on the

motherboard.Pressing down th e push pins

diagonally.

Fig. 4

Please make sure the Male and Female push pin are

joined closely. (for detailed installation instructions,

please refer to the heatsink installation section of the

user manual)

Fig. 5

Please check the back of motherboard after

installing. If the push pin is inserted as the picture,

the installation is complete.

Fig.1

Please apply an even layer of heatsink paste on

the surface of the installed CPU.

Fig. 2

(Turning the push pin along the direction of arrow is

to remove the heatsink, on the contrary, is to install.)

Please note the direction of arrow sign on the male

push pin doesn't face inwards before installation. (This

instruction is only for Intel boxed fan)

Male Push Pin

Female Push Pin

The top of Female Push Pin

GA-8I915P-D Pro Motherboard- 14 -

English

Fig.1

The DIMM socket has a notch, so the DIMM memory module

can only fit in one direction. Insert the DIMM memory module

vertically into the DIMM socket. Then push it down.

Fig.2

Close the plastic clip at both edges of the DIMM sockets to

lock the DIMM module.

Reverse the installation steps when you wish to remove the

DIMM module.

Notch

DDR II

The motherboard supports DDR II memory modules, whereby BIOS will automatically detect memory

capacity and specifications. Memory modules are designed so that they can be inserted only in one direction.

The memory capacity used can differ with each slot.

Before installing the memory modules, please comply with the following conditions:

1.Please make sure that the memory used is supported by the motherboard. It is recommended that

memory of similar capacity, specifications and brand be used.

2.Before installing or removing memory modules, please make sure that the computer power is switched

off to prevent hardware damage.

3.Memory modules have a foolproof insertion design. A memory module can be installed in only one

direction. If you are unable to insert the module, please switch the direction.

1-4Installation of Memory

Hardware Installation- 15 -

English

2 memory modules

4 memory modules

DDR II 1DDR II 2DDR II 3DDR II 4

DS/SS X DS/SS X

XDS/SS X DS/SS

DS/SS DS/SS DS/SS DS/SS

Dual Channel DDR II

GA-8I915P-D Pro supports the Dual Channel Technology. After operating the

Dual Channel Technology, the bandwidth of Memory Bus will add double up to

8.5GB/s.

GA-8I915P-D Pro includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel A : DDR II 1, DDR II 2

Channel B : DDR II 3, DDR II 4

If you want to operate the Dual Channel Technology, please note the following explanations due

to the limitation of Intel chipset specifications.

1.One/three DDR II memory module is installed: The Dual Channel Technology can't operate

when only one DDR II memory module is installed.

2.Two DDR II memory modules are installed (the same memory size and type): The Dual

Channel Technology will operate when two memory modules are inserted individually into

Channel A and B. If you install two memory modules in the same channel, the Dual Channel

Technology will not operate.

3.Four DDR II memory modules are installed: If you install four memory modules at the same

time, the Dual Channel Technology will operate only when those modules have the same

memory size and type.

We'll strongly recommend our user to slot two DDR II memory modules into the DIMMs with the same color

in order for Dual Channel Technology to work.

The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)

GA-8I915P-D Pro Motherboard- 16 -

English

1-5Installation of Expansion Cards

You can install your expansion card by following the steps outlined below:

1.Read the related expansion card's instruction document before install the expansion card into the

computer.

2.Remove your computer's chassis cover, screws and slot bracket from the computer.

3.Press the expansion card firmly into expansion slot in motherboard.

4.Be sure the metal contacts on the card are indeed seated in the slot.

5.Replace the screw to secure the slot bracket of the expansion card.

6.Replace your computer's chassis cover.

7.Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Installing a PCI Express x 16 expansion card:

Please carefully pull out the small white-

drawable bar at the end of the

PCI Express x 16 slot when you try to

install/Uninstall the VGA card. Please align

the VGA card to the onboard

PCI Express x 16 slot and press firmly down

on the slot .Make sure your VGA card is

locked by the small white-drawable bar.

Hardware Installation- 17 -

English

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the

lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

SPDIF_O (SPDIF Out)

The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to

an external Dolby Digital Decoder.

SPDIF_I (SPDIF In)

Use SPDIF In feature only when your device has digital output function.

COM A (Serial Port)

Connects to serial-based mouse or data processing devices.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as

USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.

Also make sure your OS supports USB controller. If your OS does not support USB controller, please

contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or

device(s) vendors.

LAN Port

The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of 10/100/1000Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

Connect the stereo speakers, earphone or front surround speakers to this connector.

MIC In

Microphone can be connected to MIC In jack.

Rear Speaker Out

Connect the rear surround speakers to this connector.

1-6I/O Back Panel Introduction

GA-8I915P-D Pro Motherboard- 18 -

English

1-7Connectors Introduction

1)ATX_12V

2)ATX (Power Connector)

3)CPU_FAN

4)SYS_FAN

5)PWR_FAN

6)NB_FAN

7)FDD

8)IDE

9)S_ATA0 / S_ATA1 / S_ATA2 / S_ATA3

10)PWR_LED

11)F_PANEL

12)AZALIA_FP

13)CD_IN

14)F_USB1 / F_USB2

15)F1_1394 / F2_1394

16)IR

17)CLR_CMOS

18)BAT

13

4

5

7

9

18

11

10

15

14 17

16

6

2

8

12

13

Center/Subwoofer Speaker Out

Connect the Center/Subwoofer speakers to this connector.

Side Speaker Out

Connect the side surround speakers to this connector.

You can use audio software to configure 2-/4-/6-/8-channel audio functioning.

Hardware Installation- 19 -

English

1/2)ATX_12V/ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the

components on the motherboard. Before connecting the power connector, please make sure that all

components and devices are properly installed. Align the power connector with its proper location on

the motherboard and connect tightly.

The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power

connector is not connected, the system will not start.

Caution!

Please use a power supply that is able to handle the system voltage requirements. It is

recommended that a power supply that can withstand high power consumption be used (300W or

greater). If a power supply is used that does not provide the required power, the result can lead to an

unstable system or a system that is unable to start.

Please remove the sticker on the motherboard before plugging in while the ATX power supplier is 24

pins; Otherwise, please do not remove it.

13

24

13 1

24 12

Pin No.Definition

1 3.3V

2 3.3V

3GND

4VCC

5GND

6VCC

7GND

8Power Good

9 5V SB(stand by +5V)

10 +12V

11 +12V

12 3.3V(Only for 24pins ATX)

13 3.3V

14 -12V

15 GND

16 PS_ON(soft On/Off)

17 GND

18 GND

19 GND

20 -5V

21 VCC

22 VCC

23 VCC

24 GND

Pin No.Definition

1GND

2GND

3+12V

4+12V

GA-8I915P-D Pro Motherboard- 20 -

English

3/4/5)CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN)

power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire

indicates a positive connection and requires a +12V power voltage. The black connector wire is

the ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and failure.

Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

1

6)NB_FAN (Chip Fan Connector)

If you installed wrong direction, the chip fan will not work. Sometimes will damage the chip fan.

(Usually black cable is GND)

Pin No.Definition

1+12V

2GND

1

CPU_FAN

SYS_FAN

PWR_FAN

Pin No.Definition

1GND

2+12V

3Sense

4Speed Control

(Only for CPU_FAN)

Page is loading ...

Gigabyte GA-8I915P-D Pro Owner's manual

Gigabyte GA-8I915P-D Pro Owner's manual

Related papers

Other documents