LIGHT MY BRICKS 70618 Operating instructions

Type
Operating instructions
LIGHT MY BRICKS: Destiny’s Bounty Lighting Kit
Here is the instructions document for the LEGO Destiny’s Bounty LED lighting
kit. Please read and follow the steps carefully to ensure this lighting kit is
installed properly.
If you run into any issues, please refer to the online troubleshooting guide.
Package contents:
11x White 30cm Bit Lights
3x White Strip Lights
1x 6-Port Expansion Board
1x 12-Port Expansion Board
1x 30cm Connecting Cable
2x 15cm Connecting Cables
1x 5cm Connecting Cable
1x AA Battery Pack (requires 3x AA batteries)
2x Adhesive Squares
LEGO Pieces:
2x Plate 1×6 (for mounting strip lights)
6x Round Plate 1×1 (trans red)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.
CAUTION: Forcing LEGO® to connect over a cable can result in
damaging the cable and light.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
Incorrectly inserting the connector can can result in bent pins inside
the port or possible overheating of the expansion board when
connected.
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) First remove the base of the top floor as per below images.
2.) We will first install lights to those attached to the front mast and along the
middle. Remove the front light section and then disassemble pieces as per
below:
3.) Install a White 30cm Bit Light by threading the connector side through the
base of the trans yellow brick (larger hole). Thread the cable all the way through
until the Bit Light is sitting inside the brick.
Thread the cable through the base of the black lamp shade piece as well as the
gold round plate with hole before connecting pieces together.
Reconnect the black hook piece by carefully pushing down through the top of
the lamp shade piece.
NOTE: You will notice that this particular piece will not
push all the way down. Do not force push it all the way.
It should look similar to the below example.
Lastly, reconnect the remaining piece which sits underneath the lamp before
reconnecting back to the front mast.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115

LIGHT MY BRICKS 70618 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI