ML Accessories JB007BK User manual

Type
User manual

This manual is also suitable for

ML Accessories JB007BK is an IP66-rated junction box designed for safe and secure electrical connections in both indoor and outdoor environments. With its robust construction and various drilling guides, it offers flexible cable entry points and secure mounting options. Ensure a watertight seal with its gasket-protected lid and included screw caps. Suitable for a wide range of electrical applications, it simplifies installations and provides reliable protection for your electrical connections.

ML Accessories JB007BK is an IP66-rated junction box designed for safe and secure electrical connections in both indoor and outdoor environments. With its robust construction and various drilling guides, it offers flexible cable entry points and secure mounting options. Ensure a watertight seal with its gasket-protected lid and included screw caps. Suitable for a wide range of electrical applications, it simplifies installations and provides reliable protection for your electrical connections.

INSTALLATION & MAINTENANCE MANUAL
JB007 / JB007BK / JB008 / JB008BK / JB009
JB009BK / JB0010 / JB0010BK
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
JB007 / JB007BK / JB008 / JB008BK / JB009 / JB009BK / JB0010 / JB0010BK
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• Do not overload this accessory or subject it to conditions outside its rating
This product is IP66 rated
• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods)
• Remove the lid of the junction box
• Drill out one or more of the 20mm drilling guides and remove any excess material from
around the edge of the hole to ensure a smooth surface
• Install suitable IP rated cable glands (not included) as required
• Drill the fixing holes in the rear of the box. Mark the location of the fixing holes and drill
ensuring not to infringe with any gas/water pipes or electrical cables
• Secure the box to the mounting surface and fit the screw caps provided
• Feed the mains cables through the cable glands and tighten to ensure a good seal
• Connect cables as required using suitable connectors (not included)
• Ensuring the gasket does not become damaged or pinched, refit the lid and secure
with the screws provided – the screws must be tight to ensure a good seal but do not
overtighten
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this product.
GENERAL
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
DCJUN20_V1
ACCESSORIES LTD ACCESSORIES LTD ACCESSORIES LTD
ACCESSORIES LTD
89
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
IP
66
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ML Accessories JB007BK User manual

Type
User manual
This manual is also suitable for

ML Accessories JB007BK is an IP66-rated junction box designed for safe and secure electrical connections in both indoor and outdoor environments. With its robust construction and various drilling guides, it offers flexible cable entry points and secure mounting options. Ensure a watertight seal with its gasket-protected lid and included screw caps. Suitable for a wide range of electrical applications, it simplifies installations and provides reliable protection for your electrical connections.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI