UNLESS OTHERWISE SPECIFIED:
*ALL DIMENSIONS ARE IN INCHES.
*ALL THREADS ARE UNC-2B OR UNF-2B
AFTER COATING.
*ALL THREADS ARE TO BE VERIFIED
WITH A THREAD GAGE.
*
WARNING
*
NOT TO SCALE
CONSULT FACTORY FOR
FULL SIZE TEMPLATE.
CONFIDENTIAL:
This drawing is confidential and proprietary
to Signify Holdings and may not be reproduced in whole or
in part without the express written consent of Signify
Holdings. © 2018 Signify Holdings.
All rights reserved.
ALL OPTIONS MAY NOT BE AVAILABLE. ENSURE
ACTUAL LOADING IS BELOW EPA STRENGTH OF
POLE FOR PARTICULAR HEIGHT AND WIND ZONE.
MULTIPLE FIXTURE OPTIONS
ILLUSTRATION
FIXTURE CODE
OPTION #1
OPTION #2
OPTION #3
OPTION #4
OPTION #5
OPTION #6
FIXTURES/POST
SINGLE
2 @ 180
3 @ 90
~
4 @ 90
~
2 @ 90
~
3 @ 120
~
ILLUSTRATIONS BELOW ARE BASED UPON SINGLE
FIXTURE / ARM ORIENTATION AS SHOWN IN
FOOT PRINT DRAWING ABOVE.
9-1/2" [9.50]SUGGESTED
9 11/16" [9.69]MAXIMUM
8 11/16" [8.69]MINIMUM
SINGLE FIXTURE/ARM ORIENTATION
[SEE MATRIX BELOW FOR OTHER OPTIONS]
1
TOP SECTIONED
VIEW
STREET
SIDE
HOUSE
SIDE
DOOR
VERIFY BOLD LINE
IS 9.5" LONG
PLACE LARGE WASHER BETWEEN
SMALL WASHER & POST BASE
2 1/4
"X"
SEE NOTE 2
15.00
(4) LARGE WASHERS
[SUPPLIED WITH RODS]
(4) LEVELING WASHERS
AND NUTS
(4) MOUNTING WASHERS
AND NUTS
CONDUIT
(BY OTHERS)
FOOTER
(BY OTHERS)
(4) 1/2" DIAMETER
HOT DIPPED GALVANIZED
STEEL ANCHOR RODS
WRAP-AROUND
BASE COVER
REMOVABLE
ACCESS
DOOR
SCALE = 1:5.3
NOTES:
1. SUGGESTED BOLT CIRCLE: 9 1/2" DIAMETER
MAXIMUM BOLT CIRCLE: 9 11/16" DIAMETER
MINIMUM BOLT CIRCLE: 8 11/16" DIAMETER
2. PHILIPS STRONGLY RECOMMENDS USING LEVELING
NUTS TO MOUNT THE POST BASE. IF
FOUNDATION IS NOT LEVEL, INCREASE
"X" DIMENSION ACCORDINGLY WHEN USING
LEVELING NUTS WITH WASHERS.
X = 1 5/8" WITHOUT LEVELING NUTS
X = 2 1/2" WITH LEVELING NUTS
3. IF USING GROUTING TO CONCEAL GAP BETWEEN
BASE AND FOUNDATION, ALLOW FOR WATER
DRAINAGE.
APPR
REV
ISO DOC
BY
DATE
SDK
H
19-001
AMP
1/28/2019
T01000575
PART NO:
CHECKED BY:
DRAWN BY:
APPR BY:
DATE:
DATE:
DATE:
2/27/03
J WOJTKOWIAK
7/1/03
8/4/09
M. S. PRESSEL
B. DORON
SHEET 1 OF 1
SCALE 1:1
EF-04-01-11 Rev.09
TITLE: TEMP,AR,P1500,[NEW]
PART NO:
T01000575
DRW SIZE:
C
MATERIAL: 17 X 22 WHITE BOND PAPER,
* DO NOT SCALE THIS DRAWING *
*THE ABOVE NOTE IS TO BE MOVED INTO THE DRAWING
ONLY WHEN CREATING A PDF FOR THE WEB. CHANGE
SCALE TO NTS. DO NOT SAVE CHANGES TO SLDDRW!
*THE "VERIFY BOLD LINE" NOTE IS USED FOR TEMPLATES AS
A WAY FOR THE END USER TO VERIFY THAT THE DRAWING
WAS PRINTED FULL SCALE. PICK A LINEAR ENTITY (I.E. A
LINE NOT AN ARC) ON THE DRAWING THAT WOULD BE
EASILY MEASURABLE BY THE END USER WITH A RULER OR
TAPE MEASURE. MOVE THE BOLD LINE OVER THAT ENTITY
SO IT STANDS OUT ON THE DRAWING.
-
1
Hadco P1500 Series Poles (P1511, P1516, P1521, P1526, P1561, P1566) Install Instructions
- Type
- Install Instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI