dBTechnologies SUB 600 Series User manual

MANUALE D’USO – Sezione 1

USER MANUAL - Section 1

BEDIENUNGSANLEITUNG - Abschnitt 1

CARACTERISTIQUES TECHNIQUES - Section 1

MANUAL DEL USUARIO - Sección 1

Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.

The warnings in this manual must be observed together with the "User Manual - Section 2".

Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet werden”.

Les avertissements speciés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -Section 2".

Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “Manual del usuario” - Sección 2”.

2

EMI CLASSIFICATION

FCC CLASS B STATEMENT ACCORDING TO TITLE 47, CHAPTER I,

SUBCHAPTER A, PART 15, SUBPART B

According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1)

Electromagnetic environments.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to

persons or properties. For safety reasons di not place one loudspeaker on top of another without proper fastening

systems. Before hanging the loudspeaker check all the components for damages, deformations, missing or

damaged parts that may compromise safety during installation. If you use the loudspeakers outdoor avoid spots

exposed to bad weather conditions.

Contact dBTechnologies for accessories to be used with the speakers. dBTechnologies will not accept any

responsibility for damages caused by inappropiate accessories or additional devices.

WARNING

Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

Page is loading ...

4

INDICE

1. INFORMAZIONI GENERALI ................................................................................................... 5

BENVENUTI! ........................................................................................................................ 5

PANORAMICA INTRODUTTIVA .......................................................................................... 5

RIFERIMENTI PER L’UTENTE ................................................................................................ 5

CARATTERISTICHE MECCANICHE ED ACUSTICHE ............................................................. 6

DIMENSIONI ............................................................................................................................................... 6

CARATTERISTICHE DELLA SEZIONE DI AMPLIFICAZIONE E DI CONTROLLO ................... 7

SEZIONE DI INPUT, OUTPUT E DI CONTROLLO ........................................................................................ 8

SEZIONE DI ALIMENTAZIONE .................................................................................................................... 9

2. PRIMA ACCENSIONE ............................................................................................................ 10

COLLEGAMENTO DEGLI INGRESSI E RILANCIO AUDIO .......................................................................... 11

COLLEGAMENTO DELL’ ALIMENTAZIONE ............................................................................................... 13

3. ESEMPI DI UTILIZZO ............................................................................................................. 14

UTILIZZO A TERRA ............................................................................................................ 14

UTILIZZO CON SPEAKER IN STACK ................................................................................... 14

UTILIZZO SU SUBWOOFER CON PALO TELESCOPICO..................................................... 14

4. ACCESSORI ............................................................................................................................ 15

5. RISOLUZIONE DEI PROBLEMI ............................................................................................. 16

6. SPECIFICHE TECNICHE ......................................................................................................... 17

GENERALE ................................................................................................................................................ 17

DATI ACUSTICI .......................................................................................................................................... 17

AMPLIFICATORE ....................................................................................................................................... 17

PROCESSORE ............................................................................................................................................ 18

INTERFACCIA UTENTE .............................................................................................................................. 18

INGRESSI E USCITE ................................................................................................................................... 18

SPECIFICHE DI ALIMENTAZIONE (ASSORBIMENTO / INSTALLAZIONE) ................................................. 18

DIMENSIONI ............................................................................................................................................. 19

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

INDICE

Italiano

Page is loading ...

TABLE OF CONTENTS

1. GENERAL INFORMATION .................................................................................................... 21

WELCOME! ....................................................................................................................... 21

PRODUCT OVERVIEW ....................................................................................................... 21

USER REFERENCE .............................................................................................................. 21

MECHANICAL AND ACOUSTICAL FEATURES ................................................................... 22

DIMENSIONS ............................................................................................................................................ 22

FEATURES OF THE AMPLIFIER AND CONTROL SECTIONS .............................................. 23

INPUT, OUTPUT AND CONTROL SECTION .............................................................................................. 24

POWER SUPPLY UNIT SECTION ............................................................................................................... 25

2. FIRST POWER-UP .................................................................................................................. 26

INPUT CONNECTIONS AND AUDIO DAISY CHAIN ................................................................................. 27

POWER SUPPLY CONNECTION ................................................................................................................ 29

3. USAGE EXAMPLES ................................................................................................................ 30

FLOOR USAGE ................................................................................................................... 30

USAGE WITH SPEAKER IN A STACK ................................................................................. 30

USAGE ON SUBWOOFER WITH POLE TELESCOPIC ......................................................... 30

4. ACCESSORIES ........................................................................................................................ 31

5. TROUBLESHOOTING ............................................................................................................ 32

6. SPECIFICATIONS ................................................................................................................... 33

GENERAL .................................................................................................................................................. 33

ACOUSTICAL SPECIFICATIONS ................................................................................................................. 33

AMPLIFIER ................................................................................................................................................ 33

PROCESSOR .............................................................................................................................................. 34

USER INTERFACE ...................................................................................................................................... 34

INPUTS & OUTPUTS ................................................................................................................................. 34

POWER SUPPLY SPECIFICATIONS (ABSORPTION / INSTALLATION) ....................................................... 34

DIMENSIONS ............................................................................................................................................ 35

20

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

TABLE OF CONTENTS

English

21

SUB615 - SUB618 Cod. 420120251 REV. 1.0

1. GENERAL INFORMATION

WELCOME!

PRODUCT OVERVIEW

USER REFERENCE

Thanks for purchasing a product designed and developed in Italy by dBTechnologies! This ergonomic and versatile

active subwoofer is the result of a long experience in the sound reinforcement industry, making use of optimized

sound, electronic and material research solutions.

The new SUB 600 subwoofers are equipped with a 15” woofer (SUB 615) and an 18” woofer (SUB 618),

respectively. Accurate design and sound optimisation allow for high-quality performance in a compact product.

Cabinets high ergonomics and ease of handling make them easy

to transport.

SUB 615 and SUB 618 main features are:

To make the most of your subwoofer, we recommend that you:

• an ergonomic, compact and versatile project, for both indoors and outdoors

• wooden cabinets for acoustic performance optimisation, with resistant external surfaces for both

indoor and outdoor use

• reliable, silent digital amplier

• mono/stereo input

• mono/stereo output

• dedicated DSP controls, with Polarity, Output Mode, and equalisation button (Subwoofer Mode)

• Read the quick start user manual included in the package and this user manual thoroughly and keep

this manual during the whole life of the product.

• Register your product at http://www.dbtechnologies.com under “SUPPORT”.

• Keep proof of purchase and WARRANTY (User manual “section 2”).

English

22

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

MECHANICAL AND ACOUSTICAL FEATURES

DIMENSIONS

SUB 615 and S618 have the following sizes:

• SUB 615: 430 x 580 x 600 (mm)

• SUB 618: 500 x 625 x 690 (mm)

English

23

SUB615 - SUB618 Cod. 420120251 REV. 1.0

FEATURES OF THE AMPLIFIER AND CONTROL SECTIONS

Class D digital custom amplier, SMPS, is at the heart

of SUB 615 and SUB 618.

The system is silent and is controlled by a dedicated

DSP that manages the different parameters.

The sound amplication power is 600 W RMS.

The amplier panel is made up of:

WARNING!

• Input, Output and Control Section

• Power Supply Unit Section

• Never attempt to disassemble the

amplier in any way.

• In case of overheating, the audio

volume is gradually reduced until

module thermal stabilization. The

level is autotically restored when

the correct operating temperature

is reached.

• In the event of a malfunction,

immediately cut power supply

off, by disconnecting the module

from the mains, and contact an

authorised repair centre.

POWER SUPPLY UNIT SECTION INPUT, OUTPUT AND CONTROL SECTION

• Never remove the front grille

protecting the product. To

prevent electric shock, in case of

protection grille accidental damage

or replacement (to be carried

out at the after-sales service),

immediately disconnect power

supply. Never connect mains power

supply when the grille is removed.

WARNING!

English

24

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

INPUT, OUTPUT AND CONTROL SECTION

1. INPUTS

XLR (balanced) input connectors. They may be used for mono or stereo connection. For further details

concerning connection, refer to INPUT CONNECTIONS AND AUDIO DAISY CHAIN.

4. Outputs Mode

Selector allowing to set the type of output signal (Link/Xover). It acts on the daisy-chained signal from

OUTPUT connectors [2].

5. Polarity

and Subwoofer Mode buttons

Buttons allowing to control (Normal or Reverse) Polarity and the type of output ltering (Flat, i.e. without

equalisation, Boosted, i.e. low frequencies are emphasised).

3. Subwoofer Level

Rotary switch to adjust output audio level.

2. OUTPUTS

XLR (balanced) output connectors. They may be used for mono or stereo connection. For further details

concerning connection, refer to INPUT CONNECTIONS AND AUDIO DAISY CHAIN.

6. LED (Limiter, Signal/ON)

Indicator LEDs. The Limiter LED turns on when the internal protection circuit is triggered, while Signal/ON

indicates subwoofer power-up as well as the presence of an input audio signal.

English

25

SUB615 - SUB618 Cod. 420120251 REV. 1.0

7. MAINS INPUT

VDE connector input. For connection to the mains, through the cable supplied with the device.

The FUSE section contains mains fuse housing.

8. POWER

Switch for turning device ON or OFF.

POWER SUPPLY UNIT SECTION

English

26

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

The package of SUB 615 / SUB 618 subwoofer contains:

• 615 or 618 subwoofer

• VDE power cable

• quick start user manual and warranty documents in hard copy

2. FIRST POWER-UP

CONFIGURATION AND OPTIMISATION

SUB 615 and SUB 618, used in a stand-alone conguration, are characterised

by omnidirectional sound emission. This feature is emphasised in case of low

frequencies, while it decreases as frequency

increases.

For subwoofer use optimisation in given congurations, the control panel

displays the following:

• Outputs Mode:

1. Link (the signal present at OUTPUTS is the one applied to the woofer)

2. Xover (the signal present at OUTPUTS is ltered with a crossover

frequency of 120 Hz, for daisy chain to a speaker, such as B-HYPE and

OPERA)

• Polarity:

1. Normal (audio signal normal polarity)

2. Reverse (reverse polarity, useful for wavefront optimisation through

acoustic wave phase reversal)

• Subwoofer Mode:

1. Flat (sound emission without equalisation)

2. Boosted (sound emission is emphasised in case of low frequencies)

Before power-up, set Subwoofer Level selector [3] to 0 dB (Mono or Stereo,

depending on the conguration).

English

Figure 2

27

SUB615 - SUB618 Cod. 420120251 REV. 1.0

INPUT CONNECTIONS AND AUDIO DAISY CHAIN

CASE A (MONO connection) between subwoofer and

speaker (examples: gure 1, gure 2):

According to the specic conguration (mono or stereo), one or two cables (not supplied) are required at

input and at daisy chain. XLR connectors are required.

In the event of a MONO connection between

subwoofer and speaker:

1. Connect mixer output to subwoofer INPUTS 1

connector

2. Connect subwoofer OUTPUTS 1 connector to

speaker input.

3. For each speaker, select the type of input

impedance on LINE.

4. For each channel in the conguration, set

subwoofer OUTPUTS MODE [4] to XOVER, in

order to daisy-chain a signal having a crossover

frequency of 120 Hz to the speaker.

Figure 1

English

28

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

Figure 3

CASE B (STEREO connection between a subwoofer and 2 speakers, gure 3)

1. Connect mixer L, R outputs to subwoofer INPUTS 1 and 2 respectively.

2. Daisy-chain the signal to the speakers, connecting OUTPUTS 1 to LH speaker Input, OUTPUTS 2 to RH

speaker Input.

3. Select the impedance for each speaker (“LINE” type).

4. Set subwoofer OUTPUTS MODE [4] to XOVER, in order to daisy-chain a signal having a crossover

frequency of 120 Hz to the speaker.

English

29

SUB615 - SUB618 Cod. 420120251 REV. 1.0

POWER SUPPLY

POWER SUPPLY CONNECTION

For power supply connection of the device, insert the connector of the supplied cable into "MAINS INPUT" [7].

Then insert the plug into an outlet having a proper earth conductor. Switch the POWER selector [8] to "ON".

English

30

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

3. USAGE EXAMPLES

• Types of installation other than those here described are not allowed.

• Never use the handles to suspend the subwoofer

• Always check that the positioning is stable and that the installation does not pose a danger to

people, animals or property.

USAGE ON SUBWOOFER WITH POLE

TELESCOPIC

It is possible to use only one speaker mounted on a 35 mm

diameter pole (e.g. series: OPERA, B-HYPE). The reference

accessory is DS-2 (telescopic pole).

The maximum allowed height between the speaker base and

the oor is 165 cm, except for B-HYPE 15 and OPERA 15, whose

maximum allowed height is 120 cm.

FLOOR USAGE

615 and 618 subwoofers may be used directly on the oor (see

gure opposite showing a usage example.)

USAGE WITH SPEAKER IN A STACK

A speaker may be installed directly on 615 or 618 subwoofer

by means of a DS2-S 35 mm diameter mini-pole (e.g. series:

INGENIA, B-HYPE, OPERA).

INGENIA series allows for 2 stacked speakers (specic accessories:

LP-IG and GSA-IG/GSA-IGA). In particular, in the event of 2 stacked

INGENIA IG3T or 2 stacked INGENIA IG4T, fastening by means of

additional belts is required to

ensure stable and safe installation.

English

31

SUB615 - SUB618 Cod. 420120251 REV. 1.0

To completion of the series, the following accessories are provided as options:

• Protection covers

Check the new compatible accessories on: www.dbtechnologies.com

4. ACCESSORIES

English

32

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

5. TROUBLESHOOTING

1. Check that power supply is present upstream of the installation.

2. Ensure that the power supply cable with VDE connector is properly plugged in.

1. Check that the input connection of the audio signal is correctly performed.

2. Check the cables for damage.

3. Ensure that the mixer or audio source is on and an output signal is present.

4. Check the general level through the “Subwoofer Level” control.

1. Check the cables for damage and replace them as required (a damaged cable may lead to signal loss or

alteration).

2. Ensure that Outputs Mode, Polarity and Subwoofer Mode selection settings are correct according to the

selected conguration.

The subwoofer will not turn on:

The subwoofer turns on but produces no sound:

Speaker sound is inappropriate:

English

33

SUB615 - SUB618 Cod. 420120251 REV. 1.0

6. SPECIFICATIONS

GENERAL

ACOUSTICAL SPECIFICATIONS

AMPLIFIER

Frequency response [-10dB]:

42 - 124 Hz (SUB 615) / 35 -130 Hz (SUB 618)

Max SPL (1m):

131 dB (SUB 615) / 133 dB (SUB 618)

LF:

15” (SUB 615) / 18” (SUB 618)

LF voice coil:

2.5”

Crossover frequency:

120 Hz

Type:

AMP SMPS

Amplication class

Class D

Power supply

1 x VDE

RMS amplier power:

600 W

Type:

Active subwoofer

English

34

SUB 615 - SUB618 Cod. 420120251 REV. 1.0

PROCESSOR

INPUTS & OUTPUTS

English

USER INTERFACE

Absorption at 1/8th of power in

medium use conditions (*):

0.9 A (220-240V~) - 1.6 A (110-120V~)

Absorption at 1/3rd of power in

maximum use conditions (**):

1.7 A (220-240V~) - 2.8 A (110-120V~)

Absorption with speaker on in

no-signal condition (idle):

16 W

Inrush current:

17.9 A

POWER SUPPLY SPECIFICATIONS (ABSORPTION / INSTALLATION)

* NOTE FOR INSTALLER: Values refer to 1/8th of power, under average operating conditions (music programme with occasional or no

clipping). For any type of conguration we recommend to consider them as minimum sizing values.

** NOTE FOR INSTALLER: Values refer to 1/3rd of power, under heavy operating conditions (music programme with frequent clipping and

limiter activation). In case of professional installations and tours we recommend sizing according to these values.

Internal controller:

28-bit/56-bit DSP

Limiter:

Peak, RMS, Thermal

Controls:

Subwoofer level, Ouputs Mode, Polarity, Subwoofer Mode

Inputs:

2 x XLR Balanced Inputs

Outputs:

2x XLR Balanced Outputs

35

SUB615 - SUB618 Cod. 420120251 REV. 1.0

DIMENSIONS

Product features, specications and appearance are subject to changes without prior notice. dBTechnologies

reserves the right to make changes or improvements in design or manufacture without any obligation to

incorporate such changes or improvements in products manufactured before their introduction.

A.E.B. Industriale Srl

Via Brodolini, 8

Località Crespellano

40053 VALSAMOGGIA

BOLOGNA (ITALY)

Tel +39 051 969870

Fax +39 051 969725

www.dbtechnologies.com

[email protected]

English

Material:

Multilayer wood (with protective black paint)

Grille:

NC-machined

Handles:

2, on sides

Pole mount:

Yes, 36 mm (provision: M20)

Width:

430 mm (SUB 615) 500 mm (SUB 618)

Height:

580 mm (SUB 615) 625 mm (SUB 618)

Depth:

600 mm (SUB 615) 690 mm (SUB 618)

Weight:

25.5 kg (SUB 615) 31.1 kg (SUB 618)

Page is loading ...

65

SUB615 - SUB618 Code 420120251 RÉV. 1.0

6. SPÉCIFICATIONS TECHNIQUES

INFORMATIONS GÉNÉRALES

DONNÉES ACOUSTIQUES

AMPLIFICATEUR

Réponse en fréquence [-10dB] :

42 - 124 Hz (SUB 615) / 35 -130 Hz (SUB 618)

Max SPL (1m) :

131 dB (SUB 615) / 133 dB (SUB 618)

LF :

15” (SUB 615) / 18” (SUB 618)

LF voice coil :

2.5”

Fréquence de crossover :

120 Hz

Type :

AMP SMPS

Classe d'amplication

Classe D

Alimentation

1 x VDE

Puissance d'amplication RMS :

600 W

Type :

Subwoofer actif

Français

Page is loading ...

dBTechnologies SUB 600 Series User manual

This manual is also suitable for

dBTechnologies SUB 600 Series User manual

in other languages

Related papers

Other documents