Desa Tech CTDV36NR-A Owner's manual

Brand: Desa Tech

Model: CTDV36NR-A

Category: Fireplaces

Type: Owner's manual

For more information, visit www.fmiproducts.com

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

NATURAL GAS

CTDV36NR-A

WARNING: If the information in this manual is not fol-

lowed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference.

www.fmiproducts.com

111250-01F2

SAFETy INFORMATION

TAbLE OF CONTENTS

Safety Information ............................................... 2

Local Codes......................................................... 4

Product Identication ........................................... 4

Product Features ................................................. 4

Pre-Installation Preparation ................................. 5

Location of Termination Cap ................................ 7

Venting Installation Instructions ........................... 8

Fireplace Installation.......................................... 18

Operating Fireplace ........................................... 27

Inspecting Burners............................................. 30

Cleaning and Maintenance ................................ 30

Troubleshooting ................................................ 32

Replacement Parts ............................................ 36

Service Hints ..................................................... 36

Technical Service............................................... 36

Specications .................................................... 36

Accessories ....................................................... 36

Illustrated Parts Breakdown and Parts List........ 38

Warranty Information ...........................Back Cover

WARNING: Improper in-

stallation, adjustment, al-

teration, service or main-

tenance can cause injury

or property damage. Refer

to this manual for correct

installation and operation-

al procedures. For assis-

tance or additional infor-

mation consult a qualied

installer, service agency

or the gas supplier.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases, unless

a certied kit is used.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

State of Massachusetts:

The installation must

be made by a licensed

plumber or gas tter in

the Commonwealth of

Massachusetts.

Installation and service must

be performed by a qualified

installer, service agency or the

gas supplier.

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects, or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this replace.

Improper use of this replace

can cause serious injury or

death from burns, re, explo-

sion, electrical shock and carbon

monoxide poisoning.

DANGER: Carbon Monoxide

poisoning may lead to death.

www.fmiproducts.com

111250-01F 3

SAFETy INFORMATION

Continued

This replace must be installed by a qualied

(certied or licensed) service person. It has

a sealed gas combustion chamber that uses

a coaxial pipe (pipe within a pipe and having

the same center) venting system. It brings in

fresh air for combustion through the outer pipe

and combustion gases are exhausted through

the inner pipe. If the glass door assembly and

venting pipe are not properly seated, con-

nected, and sealed, carbon monoxide leakage

(spillage) can occur.

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning resemble the u,

with headaches, dizziness, or nausea. If you

have these signs, the replace may not have

been installed properly. Get fresh air at once!

Have replace inspected and serviced by a

qualied service person. Some people are

more affected by carbon monoxide than oth-

ers. These include pregnant women, people

with heart or lung disease or anemia, those

under the inuence of alcohol, and those at

high altitudes.

Propane/LP and Natural Gas: Propane/LP and

natural gases are odorless. An odor-making

agent is added to the gas. The odor helps you

detect a gas leak. However, the odor added to

the gas can fade. Gas may be present even

though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

this replace or it’s controls can

be dangerous. Do not modify

this replace under any circum-

stances. Any parts removed for

servicing must be replaced prior

to operating replace.

WARNING: This appliance

is only for use with the type of

gas indicated on the rating plate.

This appliance is not convertible

for use with other gases unless

a certied kit is used.

WARNING: Do not use a blow-

er insert, heat exchanger insert or

other accessory not approved for

use with this replace.

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the appliance.

Do not use this replace to cook

food or burn paper or other am-

mable material.

This replace reaches high tem-

peratures. Keep children and

adults away from hot surface to

avoid burns or clothing ignition.

Fireplace will remain hot for a time

after shutdown. Allow surface to

cool before touching.

Carefully supervise young chil-

dren when they are in the room

with replace.

Keep the area around your

replace clear of combustible

materials, gasoline and other

ammable vapor or liquids. Do

not run replace where these are

used or stored.

1. For propane/LP replace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

www.fmiproducts.com

111250-01F4

SAFETy INFORMATION

Continued

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier's instructions

• if you cannot reach you gas supplier, call

the re department.

3. Never install the replace

• in a recreational vehicle

• in windy or drafty areas where curtains

or other combustible (ammable) objects

can make contact with the fireplace

front

• in high trafc areas

4. Turn appliance off and let cool before

servicing, installing or repairing. Only a

qualied service person should install,

service or repair this replace. Have re-

place inspected annually by a qualied

service person.

5. You must keep control compartments,

burners and circulating air passages

clean. More frequent cleaning may be

needed due to excessive lint and dust

from carpeting, bedding material, etc.

Turn off the gas valve and pilot light before

cleaning replace.

6. Have venting system inspected annu-

ally by a qualified service person. If

needed, have venting system cleaned or

repaired.

7. Do not use any solid fuels (wood, coal,

paper, cardboard, etc.) in this replace.

8. This appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, with the National Electrical Code,

ANSI/NFPA 70 or the Canadian Electrical

Code, CSA C22.1.

9. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service person to arrange

for replacement of the unit.

10. Do not operate replace if any log is bro-

ken.

11. Do not operate fireplace with glass door

removed, cracked or broken.

12. Provide adequate clearances around air

openings.

Figure 1 - Tudor Direct-Vent Fireplace

with Millivolt Ignition

Glass Door

Assembly

ON/OFF/

REMOTE

Switch (Optional

Installation)

Upper Louver

Panel

Lower

Louver

Panel

Flue Collar

Nailing

Flange

LOCAL CODES

Install and use replace with care. Follow all

local codes. In the absence to local codes,

use the current National Fuel Gas Code ANSI

Z223.1/NFPA 54* (USA) or the current CSA-

B149.1 Installation Code (Canada).

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT

IDENTIFICATION

PRODUCT FEATURES

These are a few facts that can help you understand

and enjoy your direct-vent replace:

• The venting system may be routed to the outside

of your home in several ways. It may vent through

the roof (vertical) or it may vent to an outside/

exterior wall (horizontal). The vent pipe installation

is very important to allow for proper operation. You

must follow the venting instructions very carefully

for either vertical or horizontal applications.

• This replace may be installed in any room of

your house provided all local codes and these

installation instructions are followed.

Control

Valve

Glowing

Embers

Blower Switch

(Optional

Installation)

Grate

Assembly

Lava Rock

Log Set

Piezo

Ignitor

www.fmiproducts.com

111250-01F 5

Figure 2 - Common Fireplace Locations

Flush with a wall

Through exterior wall

enclosed in a chase

Corner

installation

• This replace requires a wall switch, hand-held

remote or wall thermostat (millivolt) for operation

(see Accessories, page 36).

• This replace does not require electricity to oper-

ate.

• Only the blower requires electricity if installed and

if you plan to install the blower at a later date, do

not forget to wire the outlet at the bottom of the

replace when framing.

• A piezo ignitor and ceramic electrode create

spark to ignite the pilot light. It does not require

any matches, batteries or any other sources of

ignition to light the pilot.

• Each time you turn on your replace, you may

notice some amount of condensation on the

inside of the replace glass. This is normal and

will disappear after 10-20 minutes of operation.

• Your direct-vent gas replace system (replace

and venting) is a balanced and sealed gas

operating unit. It requires approximately 10-20

minutes of operating time before the ame pattern

stabilizes.

PRE-INSTALLATION

PREPARATION

LOCATION AND SPACE REQUIREMENTS

Determine the safest and most efficient location for

your FMI PRODUCTS, LLC direct-vent fireplace.

Make sure that rafters and wall studs are not in the

way of the venting system. Choose a location where

the heat output is not affected by drafts, air condition-

ing ducts, windows or doors. Figure 2 shows some

common locations. Be aware of all restrictions and

precautions before deciding the exact location for your

fireplace and termination cap.

When deciding the location of your fireplace, follow

these rules:

• Do not connect this fireplace venting to a chimney

flue serving a separate solid-fuel burning fireplace

or appliance.

• Due to high temperatures, do not locate this fireplace

in high traffic areas, windy or drafty areas or near

furniture or draperies.

• Proper clearances must be maintained.

• If your fireplace is to be installed directly on carpet-

ing, vinyl tile or any combustible material other than

wood, it must be installed on a metal or wood panel

extending the full width and depth of the fireplace.

See Figure 3.

• Your fireplace is designed to be used in zero clear-

ance installations. Wall or framing material can be

placed directly against any exterior surface on the

back, sides or top of your fireplace, except where

standoff spacers are integrally attached. If standoff

spacers are attached to your fireplace, these spac-

ers can be placed directly against wall or framing

material. See framing details on page 6.

• If you plan on installing a television or entertainment

center recessed above your fireplace, it is recom-

mended that you maintain a minimum 18" above

top of louver opening.

• When locating termination cap, it is important to

observe the minimum clearances shown in Figure

7, page 7.

• If recessing into a wall, you can avoid extra framing

by positioning your fireplace against an already

existing framing member.

• Do not recess termination cap into a wall or sid-

ing.

• You may paint the termination cap with 450º F

(232º C) heat-resistant paint to coordinate with the

exterior finish.

• There must not be any obstruction such as bushes,

garden sheds, fences, decks or utility buildings

within 24" from the front of the termination cap.

• Do not locate termination cap where excessive

snow or ice build up may occur. Be sure to clear

vent termination area after snow falls to prevent

accidental blockage of venting system. When

using snow blowers, do not direct snow towards

vent termination area.

Figure 3 - Fireplace Bottom Dimensions

41"

29"

PRODUCT FEATURES

Continued

www.fmiproducts.com

111250-01F6

PRE-INSTALLATION

PREPARATION

Continued

Figure 4 - Framing Clearances for

Installation Against an Exterior Wall

Figure 5 - Framing Clearances for Corner

Installation

T o p of Louver

Opening

Wa ll

Ref.

Mantel

Depth Ref.

Mantel from Top of

Louver Opening

1 14" A 16"

2 12" B 14"

3 10" C 12"

4 8" D 10"

5 6" E 8"

6 4" F 6"

7 2" G 4"

Figure 6 - Clearances for Combustible

Mantels

CLEARANCES

Minimum clearances to combustibles for the

replace are as follows:

Back and sides 0"

Perpendicular walls 6"

Floor 0"

Ceiling to louver opening 42"

Front 36"

Top of Standoffs 0"

Vent (See venting

instructions for specic

venting clearances.)

Combustible material with a maximum thick-

ness of 5/8" may be ush with the top front of

replace.

NOTICE: This replace is in-

tended for use as supplemental

heat. Use this replace along with

your primary heating system. Do

not install this replace as your

primary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using replace. This will

help circulate the heat through-

out the house. In the event of a

power outage, you can use this

replace as a heat source.

FRAMING AND FINISHING

Figure 4 shows typical framing of this replace.

Figure 5 shows framing for corner installation.

All minimum clearances must be met.

For available accessories for this replace,

see Accessories on page 36. If you are using

a separate combustible mantel piece, refer to

Figure 6 for proper installation height. You can

install noncombustible mantels at any height

above the replace.

Note: Noncombustible mantels may dis-

color!

Nailing Tabs

15" 49

41"

Nailing

Tabs

www.fmiproducts.com

111250-01F 7

Figure 7 - Minimum Clearances for Termination Cap

LOCATION OF TERMINATION CAP

Fixed

Closed

Openable

Fixed

Closed

TERMINATION CAP

AIR SUPPLY INLET

GAS METERRESTRICTED AREA

(TERMINATION PROHIBITED)

A = clearance above grade, veranda, porch, deck, or

balcony [*12" (30.5 cm) minimum]

B = clearance to window or door that may be opened

[12" (30.5 cm) minimum]

C = clearance to permanently closed window

[minimum 12" (30.5 cm) recommended to prevent

condensation on window]

D = vertical clearance to ventilated soffit located above the

terminal within a horizontal distance of 24" (61 cm) from

the center-line of the terminal [18" (45.7 cm) minimum]

E = clearance to unventilated soffit [12" (30.5 cm) minimum]

F = clearance to outside corner (see below)

G = clearance to inside corner (see below)

H = *not to be installed above a meter/regulator assembly

within 36" (91.4 cm) horizontally from the center line

of the regulator

I = clearance to service regulator vent outlet [*72" (182.9 cm)

minimum]

J = clearance to non-mechanical air supply inlet to building

or the combustion air inlet to any other fireplace

[*12" (30.5 cm) minimum]

K = clearance to a mechanical air supply inlet [*72" (182.9 cm)

minimum]

L = † clearance above paved side-walk or a paved driveway

located on public property [*84" (213.3 cm) minimum]

M = clearance under veranda, porch, deck

[*12" (30.5 cm) minimum ‡]

N = clearance above a roof shall extend a minimum of

24" (61 cm) above the highest point when it passes

through the roof surface and any other obstruction within

a horizontal distance of 18" (45.7 cm)

† vent shall not terminate directly above a side-walk or paved driveway which is located between two

single family dwellings and serves both dwellings*

‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*

* as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.

Note: Local codes or regulations may require different clearances

A = 6" (15.2 cm)

Inside Corner

B = 6" (15.2 cm)

C = Maximum depth of 48" (121.9 cm)

for recessed location

D = Minimum width for back wall of

recessed location -

Combustible - 38" (965 mm)

Noncombustible - 24" (61 cm)

E = Clearance from corner in

recessed location-

Combustible - 6" (15.2 cm)

Noncombustible - 2" (5.1 cm)

Outside Corner Recessed Location

G = 12" (30.5 cm) minimum clearance

Balcony with No Side Wall

Combustible &

Noncombustible

H = 24" (61 cm)

J = 20" (50.8 cm)

Balcony with Perpendicular Side Wall

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Openable

www.fmiproducts.com

111250-01F8

VENTING INSTALLATION

INSTRUCTIONS

NOTICE: Read these instruc-

tions completely before at-

tempting installation.

These models are tested and approved for

use with FMI PRODUCTS, LLC (direct-vent)

pipe components and terminations as well as

Simpson-Duravent direct-vent pipe compo-

nents and terminations.

The venting system must terminate on the

outside of the structure and can not be at-

tached to a chimney or ue system serving a

separate solid fuel or gas burning appliance.

A direct-vent appliance must have its own

venting system. DO NOT common vent this

appliance.

These models are approved to be vented

either horizontally through an outside wall or

vertically through a roof or chase enclosure

using the following guidelines:

• When venting system terminates horizon-

tally on an outside wall, you may install

a standoff if the termination cap is to be

installed directly on a combustible nish

such as vinyl, wood, stucco, etc.

• Never run the vent downward as this may

cause excessive temperatures which

could cause a re.

• Vent pipe air space clearances to com-

bustibles are 1" on all sides except on the

horizontal sections, which requires 2" clear-

ance from the top of the pipe. Where the

termination cap penetrates a combustible

wall, 1" air space clearance is required.

• Snorkel terminations are required when

minimum clearance to grade cannot be

met (see Figure 16 on page 12).

• Have replace and selected vent compo-

nents on hand to help determine the exact

measurements when elbowing or offsetting.

Always use wall restops when penetrating

walls and restops when penetrating ceil-

ings or attic spaces.

• If using a venting conguration of only

horizontal venting with no vertical run, a

1/4" rise for every 12" of run toward the

termination is required.

WARNING: Read all instruc-

tions completely and thoroughly

before attempting installation.

Failure to do so could result in

serious injury, property damage

or loss of life.

NOTICE: Failure to follow these in-

structions will void the warranty.

NOTICE: Do not seal termination

cap to vent pipe. Cap must be

removable for vent inspection

and maintenance.

INSTALLATION PRECAUTIONS

• Wear gloves and safety glasses for protection

• Use extreme caution when using ladders or when

on roof tops

• Be aware of electrical wiring locations in walls and

ceilings

The following actions will void the warranty on your

venting system:

• Installation of any damaged venting component

• Unauthorized modication of the venting system

(Do not cut or alter vent components)

• Installation of any component part not manufac-

tured or approved by FMI PRODUCTS, LLC

• Installation other than as instructed by these

instructions

WARNING: This gas replace

and vent assembly must be vented

directly to the outside. The venting

system must NEVER be attached

to a chimney serving a separate

solid fuel burning appliance. Each

direct-vent gas appliance must

use a separate vent system. Do not

use common vent systems.

WARNING: Vent pipe air

space clearances to combustibles

are 1" on all sides except on the

horizontal sections, which require

2" clearances from the top of the

pipe. Where the termination cap

penetrates a combustible wall, 1"

air space clearance is required.

www.fmiproducts.com

111250-01F 9

INSTALLATION PLANNING

There are two basic types of direct-vent

installation:

• Horizontal Termination

• Vertical Termination

Horizontal Termination Installation

IMPORTANT: Horizontal square terminations

require only inner portion of wall restop.

Horizontal installations using round termina-

tion require exterior portion of wall restop

available only in vent kit HTK (see Figure

14, page 11).

1. Set the replace in its desired location and

determine the route your horizontal venting

will take. Do not secure the replace until

all venting has been installed. Some instal-

lations require sliding the replace in and

out of position to make nal venting con-

nections. Figures 14 through 18 on pages

11 through 13 show different congurations

for venting with horizontal termination that

will help you decide which application best

suits your installation. Check to see if wall

studs or roof rafters are in the path of your

desired venting route. If they are, you may

want to adjust the location of the replace.

2. Direct vent pipe sections and components

are designed with special twist-lock con-

nections.

Twist-Lock Procedure: The female ends of

the pipes have locking lugs (indentations).

These lugs will slide straight into match-

ing slots on the male ends of adjacent

pipes. Push pipe sections together and

twist one section clockwise approximately

one-quarter turn until the sections are fully

locked (see Figure 8). Note: Horizontal runs

of vent must be supported every three feet.

Use wall straps for this purpose.

3. Use a 45° elbow to connect venting sys-

tem to replace ue collar. The elbow is

designed to be twist-locked onto the ue

collar as described in step 2. IMPORTANT:

Do not attempt to alter the conguration

of the elbow by cutting, twisting, bending,

etc.

4. Assemble the desired combination of pipe

and elbows to the replace ue collar. If

there are long portions of venting run, pre-

assembled pipe sections may be installed

VENTING INSTALLATION

INSTRUCTIONS

Continued

Figure 8 - Vent Pipe Connections

Female

Locking Lugs

Male

Slots

(Framing

Detail)

10"

10" Inside Framing

10"

Vent Opening

Combustible Wall

Vent Opening

Noncombustible Wall

Figure 9 - Vent Opening Requirements

Center of

Hole

as subassemblies for convenience.

5. Carefully determine the location where

the vent pipe assembly will penetrate

the outside wall. The center of the hole

should line up with the center-line of the

horizontal vent pipe. Mark the wall for a

10" x 10" square hole. Cut and frame the

square hole in the exterior wall where the

vent will be terminated. If the wall being

penetrated is constructed of noncombus-

tible material, such as masonry block or

concrete, a 7

" hole with zero clearance

is acceptable (see Figure 9).

www.fmiproducts.com

111250-01F10

VENTING INSTALLATION

INSTRUCTIONS

Continued

WARNING: Do not recess

vent termination into any wall.

This will cause a re hazard.

6. Noncombustible Exterior Wall: Position the

horizontal vent cap in the center of the 7

" round hole and attach to the exterior

wall with four wood screws provided.

Before attaching the vent cap to exterior

wall, run a bead of non-hardening mastic

(pliable sealant) around the outside edges

to make a seal between it and the outside

wall. Note: The four wood screws provided

should be replaced with appropriate fas-

teners for stucco, brick, concrete or other

types of sidings.

Combustible Exterior Wall: For vinyl siding,

stucco or wood exteriors, a siding standoff

may be installed between the vent cap and

exterior wall. The siding standoff prevents

excessive heat from damaging the siding

materials. Siding material must be cut to

accommodate standoff. Bolt the vent cap to

the standoff. Apply non-hardening mastic

around outside edge of standoff. Position

the standoff/cap assembly in the center of

the 10" square hole and attach to exterior

wall with wood screws provided (see Fig-

ure 11). The siding standoff must sit ush

against the exterior fascia material.

Combustible Exterior Wall Only: Slide the

wall restop over the vent pipe before

connecting horizontal run to vent cap (see

Figure 12).

8. Carefully move replace, with vent as-

sembly attached, toward wall and insert

vent pipe into horizontal termination. The

pipe overlap should be a minimum of 1

(see Figure 13, page 11).

Combustible Exterior Wall Only: Slide wall

restop against interior wall surface and

attach with screws provided. See Figure

13, page 11, for horizontal termination

details.

10. Place replace into position and shim with

noncombustible material if needed. Nail or

screw side anges to framing to secure

unit in place. IMPORTANT: Make sure re-

place is level before securing. If replace

is not level it will not work properly.

Figure 10 - Installing Horizontal Vent Cap

(Noncombustible Exterior)

Wood Screw

Vent Cap

Figure 11 - Installing Siding Standoff

(Combustible Exterior Wall)

Cut Siding Away to

Fit Standoff

Wood

Screw

Screws

Standoff

Vent

Cap

Apply Mastic

to All Four Sides

Vent Cap

(Horizontal

Termination)

Interior Wall

Surface

Wall

Firestop

Horizontal

Vent Pipe

Figure 12 - Connecting Vent Cap with

Horizontal Vent Pipe

Screw

Apply Mastic to

All Four Sides

www.fmiproducts.com

111250-01F 11

VENTING INSTALLATION

INSTRUCTIONS

Continued

Figure 13 - Typical Horizontal

Termination Cap Mounting with

Additional Siding Standoff Installed

Siding Standoff

Screws

High Wind

Termination

Apply

Mastic to

Outside

Edge of

Standoff

Exterior Wall with Vinyl Siding

10" x 10" Framed

Opening

Maintain 1"

Minimum Air

Space Around

Outer Pipe When

Penetrating a Wall

Minimum Pipe

Overlap 1

Wall

Firestop

Direct-Vent

Pipe

Horizontal Termination Congurations

Figures 14 through 18 show different congura-

tions and alternatives for venting with horizontal

termination. Each gure includes a chart with

critical minimum and maximum dimensions

which MUST be met. IMPORTANT: If using a

venting conguration of only horizontal venting

with no vertical run, a 1/4" rise for every 12" of

run toward the termination is required.

NOTICE: Do not seal termination

cap to vent pipe. Cap must be

removable for vent inspection

and maintenance.

WARNING: Never run vent

downward as this may cause

excessive temperatures which

could cause a re. Operation of

improperly installed and main-

tained venting system could

result in serious injury, property

damage or loss of life.

GROUND FLOOR INSTALLATION

Recommended Applications:

• Installation using cabinet surrounds

• Through the wall using round or square

termination (up to 12" horizontal pipe)

• NOT FOR CORNER INSTALLATION

Horizontal

High Wind

Square

Termination

Wall Firestop

45° Elbow

Figure 14 - Horizontal Termination

Conguration for Square and Round

Terminations

45° Elbow

Wall

Firestop

Slide Ring

Over Elbow

to Complete

Connection

Exterior Portion

of Wall Firestop

(Round

Termination

Only)

Adjustable

Pipe 12" Max.

Round Termination

(Kit HTK Shown)

* If installing this replace at altitudes of

4000 feet and above, it is recommended

that an additional vertical height of 6" be

added to the vent system.

Square Termination

Vertical (V) Horizontal (H)

32" min. 17" Max.

Round

Termination

Cap

www.fmiproducts.com

111250-01F12

CORNER AND ALTERNATE INSTALLATION

Recommended Applications:

• Corner ground oor installation

• Ground oor installation where pipe vents hori-

zontally through wall (over 12" horizontal pipe)

• Basement installation where one foot clear-

ance from ground to termination is possible

VENTING INSTALLATION INSTRUCTIONS

Continued

Figure 15 - Horizontal Termination Conguration for Corner Installation Using One

90° Elbow

Square

Termination

Wall

Firestop

Not to Exceed (H) Limits

As Required

for (V), See

Chart for

Pipe Section

Required

45° Elbow

90° Elbow

Square

Termination

Wall

Firestop

45° Elbow

12" Min.

Required

Vertical (V) Vertical Pipe Horizontal (H)

*43

" min. None 30" max.

" min. 1 ft. 48" max.

" min. 2 ft. 60" max.

" min. 3 ft. 84" max.

" min. 4 ft. 20' max.

* Ground Floor Corner Venting

Not to Exceed

(H) Limits

SNORKEL TERMINATION INSTALLATION

Recommended Applications:

• Installations requiring a vertical rise on building exterior

• Any installation using snorkel termination to achieve one foot above ground

Snorkel terminations are available for installations requiring a vertical rise on the exterior of

the building. If installing snorkel termination below grade, you must provide proper drainage

to prevent water from entering snorkel termination (see Figure 16). Do not back ll around

snorkel termination.

Snorkel Termination

12"

Min.

Snorkel

Termination

Wall

Firestop

90° Elbow

45° Elbow

Figure 16 - Snorkel Termination Congurations for Below Ground Installation

Snorkel Termination

Adequate

Drainage

12" Min.

www.fmiproducts.com

111250-01F 13

VENTING INSTALLATION INSTRUCTIONS

Continued

Venting with Two 90° Elbows

Vertical (V) Horizontal (H

)

Horizontal (H

) +

Horizontal (H

)

5' min. 2' max. 6' max.

6' min. 4' max. 12' max.

7' min. 6' max. 18' max.

8' min. 8' max. 20' max.

20' max. 8' max. 20' max.

Figure 17 - Horizontal Termination Conguration for Venting Using Two 90° Elbows

45° Elbow

HORIZONTAL SYSTEM INSTALLATION

USING TWO 90° ELBOWS

The following congurations show the minimum

vertical rise requirements for a horizontal sys-

tem using two 90° elbows.

Venting with Two 90° Elbows

Vertical (V)

Horizontal (H

) +

Horizontal (H

)

5' min. 6' max.

6' min. 12' max.

7' min. 18' max.

8' min. 20' max.

20' max. 20' max.

Figure 18 - Horizontal Termination Conguration for Venting Using Two 90° Elbows

with Termination at 90° with Fireplace

45° Elbow

www.fmiproducts.com

111250-01F14

INSTALLATION FOR VERTICAL

TERMINATION

Note: Vertical restrictor must be installed in

all vertical installations.

1. Determine the route your vertical venting

will take. If ceiling joists, roof rafters or

other framing will obstruct the venting

system, consider an offset (see Figure 19)

to avoid cutting load bearing members.

Note: Pay special attention to these instal-

lation instructions for required clearances

(air space) to combustibles when passing

through ceilings, walls, roofs, enclosures,

attic rafters, etc. Do not pack air spaces

with insulation. Also note maximum verti-

cal rise of the venting system and any

maximum horizontal offset limitations.

2. Set the replace in desired location. Drop

a plumb line down from the ceiling to the

position of the replace exit ue. Mark the

center point where the vent will penetrate

the ceiling. Drill a small locating hole at

this point.

Drop a plumb line from the inside of the

roof to the locating hole in the ceiling.

Mark the center point where the vent will

penetrate the roof. Drill a small locating

hole at this point.

Flat Ceiling Installation

Cut a 10" square hole in the ceiling using

the locating hole as a center point. The

opening should be framed to 10" x 10"

inside dimensions, as shown in Figure 9

on page 9 using framing lumber the same

size as the ceiling joists. If the area above

the ceiling is an insulated ceiling or attic

space, nail restop from the top side. This

prevents loose insulation from falling into

the required clearance space. If the area

above the ceiling is a living space, install

restop below the framed hole. The restop

should be installed with no less than three

nails per side (see Figure 20).

2. Assemble the desired lengths of pipe

and elbows necessary to reach from the

replace ue up through the restop. Be

sure all pipe and elbow connections are

fully twist-locked (see Figure 8, page 9).

3. Cut a hole in the roof using the locating

hole as a center point. (Cover any exposed

open vent pipes before cutting hole in roof.)

The 10" x 10" hole must be measured on

the horizontal; actual length may be larger

depending on the pitch of the roof. There

must be a 1" clearance from the vent pipe to

combustible materials. Frame the opening

as shown in Figure 9, page 9.

VENTING INSTALLATION

INSTRUCTIONS

Continued

Figure 19 - Offset with Wall Strap and 45°

Elbows

45° Elbow

Wall Strap

Roof Flashing

Ceiling Firestop

Figure 20 - Installing Firestop

If area above is a living space, install

restop below framed hole.

If area above is an attic or insulated area,

install restop above framed hole.

www.fmiproducts.com

111250-01F 15

4. Connect a section of pipe and extend up

through the hole.

Note: If an offset is needed to avoid

obstructions, you must support the vent

pipe every 3 feet. Use wall straps for this

purpose (see Figure 19, page 14). When-

ever possible, use 45° elbows instead of

90° elbows. The 45° elbow offers less

restriction to the ow of the ue gases

and intake air.

5. Place the ashing over the pipe section(s)

extending through the roof. Secure the

base of the ashing to the roof and fram-

ing with roong nails. Be sure roong

material overlaps the top edge of the

ashing as shown in Figure 19, page 14.

There must be a 1" clearance from the

vent pipe to combustible materials.

6. Continue to add pipe sections until the

height of the vent cap meets the minimum

building code requirements described in

Figure 7 on page 7. Note: You must in-

crease vent height for steep roof pitches.

Nearby trees, adjoining rooines, steep

pitched roofs and other similar factors

may cause poor draft or down-drafting

in high winds. Increasing the vent height

may solve this problem.

7. Twist-lock the vent cap onto the last sec-

tion of vent pipe.

Note: If the vent pipe passes through any oc-

cupied areas above the rst oor, including

storage spaces and closets, you must enclose

pipe. You may frame and sheetrock the en-

closure with standard construction material.

Make sure and meet the minimum allowable

clearances to combustibles. Do not ll any of

the required air spaces with insulation.

VENTING INSTALLATION

INSTRUCTIONS

Continued

Vertical Termination Congurations

Figures 21 through 24 show four different

congurations for vertical termination.

Venting with Two 90° Elbows

Vertical (V)

Horizontal (H

) +

Horizontal (H

)

5' min. 2' max.

6' min. 4' max.

7' min. 6' max.

8' min. 8' max.

20' max. 8' max.

Figure 21 - Vertical Venting

Conguration Using Two 90° Elbows

with Two Horizontal Runs (Vertical

Round High Wind Termination Shown)

Note: Install restrictor

into inner collar of

replace as shown.

45° Elbow

Venting with One 90° Elbow

Vertical (V) Horizontal (H)

5' min. 2' max.

6' min. 4' max.

7' min. 6' max.

8' min. 8' max.

20' max. 8' max.

Figure 22 - Vertical Venting

Conguration Using One 90° Elbow

(Vertical Round High Wind Termination

Shown)

45° Elbow

Note: Install restrictor into

inner collar of replace as

shown.

www.fmiproducts.com

111250-01F16

VENTING INSTALLATION

INSTRUCTIONS

Continued

Note: Install

restrictor into

inner collar of

replace as

shown.

Venting with Two 90° Elbows

Vertical (V

) Horizontal (H)

5' min. 6' max.

6' min. 12' max.

7' min. 18' max.

8' min. 20' max.

Note: Vertical (V

) + Vertical (V

) = 40' max.

Figure 23 - Vertical Venting

Conguration Using Two 90° Elbows

(Vertical Round High Wind Termination

Shown)

45° Elbow

Vertical Venting

V = 40' max.

Figure 24 - Vertical Venting

Conguration With No Horizontal Run

(Vertical Round High Wind Termination

Shown)

Note: Install

restrictor into

inner collar of

replace as

shown.

45° Elbow

Your FMI PRODUCTS, LLC direct-vent re-

place has been tested and approved for eleva-

tions from 0-2,000 feet (USA) and elevations

from 0-4,500 feet (Canada).

When installing this replace at an elevation

above 2,000 feet (in the USA), you may need

to decrease the input rating by changing the

existing burner orice to a smaller size. Re-

duce input 4% for each 1,000 feet above sea

level. Check with your local gas company for

proper orice size identication.

HIGH ALTITUDE INSTALLATION

When installing this replace at an elevation

above 4,500 feet (in Canada), check with

local authorities.

Consult your local gas company to help deter-

mine the proper orice for your location.

For assistance with any high altitude installa-

tion, contact FMI PRODUCTS, LLC’s Custom-

er Service Department at 1-866-328-4537.

www.fmiproducts.com

111250-01F 17

PARTS LIST FOR VENTING KITS

AND COMPONENTS

FMI PRODUCTS, LLC Pipe & Vent Kits

Number Description

P47-6 6" Section Coaxial Pipe,

Galvanized

P47-12 12" Section Coaxial Pipe,

Galvanized

P47-24 24" Section Coaxial Pipe,

Galvanized

P47-36 36" Section Coaxial Pipe,

Galvanized

P47-48 48" Section Coaxial Pipe,

Galvanized

PA47-712 Adjustable 7"-12" Section

Coaxial Pipe, Galvanized

VKG-47 Ground Floor Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

Horizontal Square Termination,

16 Screws)

VKB-47 Basement Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

Horizontal Square Termination,

4' Pipe, 90° Elbow, 20 Screws)

VKS-47 Snorkel Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

36" Snorkel Termination, 4' Pipe,

1' Pipe, 90° Elbow, 26 Screws)

VKR-47 Roof Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Flue Restrictor,

Vertical High Wind Termination,

2' Pipe, 4' Pipe, Wall Firestop,

Storm Collar, Roof Flashing

[0/12 - 6/12], 26 Screws)

VKC-47 Corner Vent Kit, Galvanized

(Includes 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

Horizontal Termination, 6" Pipe,

90° Elbow, 18 Screws)

VENTING INSTALLATION

INSTRUCTIONS

Continued

Number Description

HTK Horizontal Round Termination Kit

(Includes: Round Termination,

Wall Firestop and 45° Elbow)

HTKS-47 Horizontal Square Termination Kit

(Includes: Square Termination,

Wall Firestop, 45° Elbow)

FMI PRODUCTS, LLC Elbows

Number Description

E47-45 45° Elbow, Galvanized

E47-90 90° Elbow, Galvanized

FMI PRODUCTS, LLC Terminations

Number Description

HT-47 Horizontal Round Termination,

Galvanized

HTS-47 Horizontal Square Termination,

Galvanized

VT-47 Vertical Round Termination,

Galvanized

ST-47-14 14" Snorkel Termination,

Galvanized

ST-47-36 36" Snorkel Termination,

Galvanized

FMI PRODUCTS, LLC Venting

Accessories

Number Description

SC-47 Storm Collar, Galvanized

WF-47 Wall Firestop, Galvanized

RF-47-6 Roof Flashing - 0 to 6/12 Pitch,

Galvanized

RF-47-12 Roof Flashing - 6/12 to 12/12 Pitch,

Galvanized

VR-47 Vertical Restrictor, Galvanized

S-47 Combustible Siding Standoff,

Galvanized

WS-47 Wall Strap

FP-47 Firestop Plate

www.fmiproducts.com

111250-01F18

FIREPLACE

INSTALLATION

CHECK GAS TYPE

Use proper gas type for replace unit you are in-

stalling. If your gas supply is not correct, do not in-

stall replace. See retailer where you purchased

the replace for proper replace according to

your gas type or to purchase gas conversion kit

(see Accessories, page 36). A conversion kit is

supplied with the CTDV36NRA.

INSTALLING OPTIONAL BLOWER

ACCESSORIES

NOTICE: If installing blower in

an existing replace with gas

connections, shut off gas sup-

ply and disconnect heater from

gas supply. Contact a qualied

service person to do this.

WARNING: If there is a duplex

electrical outlet installed in the

right side of the bottom of the

replace base area, be sure that

the electrical power to the outlet is

turned off before proceeding with

blower installation. Failure to do

this may result in serious injury.

Model BK Installation

Follow all instructions provided in blower ac-

cessory kit.

1. Attach the power cord to blower motor by

rmly pushing two female terminals at end

of power cord onto two spade terminals on

blower motor (see Figure 25).

2. Attach green ground wire from power cord

to blower housing using screw provided (see

Figure 25). Tighten screws securely.

3. Place blower against lower rear wall of re-

box outer wrapper with exhaust port directed

upward. The blower will t inside back open-

ing and be held in position against back wall

by magnets (see Figure 25).

4. Be certain that all wire terminals are securely

attached to terminals on blower motor and

screw retaining green ground wire is tight.

5. Mount speed control box to switch bracket by

placing plastic control shaft forward through

opening in switch bracket (see Figure 26).

6. While supporting speed control, secure

control shaft with lock nut by pushing and

turning lock nut with pliers clockwise until it

is tight against front panel. Place control knob

provided on shaft.

7. Turn on power to duplex outlet if previously

turned off per the warning above.

8. Plug in blower power cord.

a. If your rebox is installed as a freestand-

ing unit with an accessory mantel, deter-

mine whether power cord will exit left side

or right side of rebox. Route power cord

through exit hole and plug power cord

into a wall receptacle near rebox.

b. If your rebox installation is recessed

and/or pre-wired, plug power cord into

duplex outlet provided. Refer to your

rebox owner’s manual for instructions

on wiring duplex outlet.

CAUTION: Never touch the

blower wheel while in operation.

Figure 25 - Blower Model BK

Green

Ground Wire

Screw

Spade

Terminals

Magnetic

Strips

Exhaust

Port

Side View

Lower Firebox

Cavity

Blower

Location

Figure 26 - Attaching Speed Control to

Firebox

Switch

Bracket

Locknut

Control

Shaft

Control

Knob

Speed

Control

Blower

Plug-In

Duplex Outlet

(Located under-

neath rebox oor

against lower right

outside wall)

www.fmiproducts.com

111250-01F 19

FIREPLACE

INSTALLATION

Continued

Figure 27 - Location of Wiring Diagram

Decal (Model May Vary from Illustration)

Wiring Diagram

Decal 12" in Front

of Burner

9. Check to make sure power cord is completely

clear of blower wheel and there are no other

foreign objects in blower wheel. Turn blower

on and check for operation. Turn blower off

by turning knob fully counterclockwise before

continuing.

10. Peel off backing paper and stick supplied wiring

diagram decal on rebox bottom approximately

12" in front of blower (see Figure 27).

Model BKT Installation

Note: When installing BKT thermostatically-controlled

blower, you must rst secure thermal switch bracket

to blower if it has not already been factory installed.

1. Place green ground wire with ring terminal

between bottom hole on thermal switch bracket

and top ear hole on blower assembly. Insert

phillips screw into all three pieces and tighten

securely (see Figure 28).

2. Connect wire harness and power cord terminals.

Connect blue jumper wire to blower motor ter-

minal and right side terminal of thermal switch.

Connect black wire to left side of thermal switch

and white wire to other remaining blower motor

terminal.

Note: Power cord outer insulation sleeve may have

to be stripped slightly to allow enough wire length

to reach and make all connections. DO NOT trim

excessive length away. Just enable enough to make

all connections securely.

3. Place blower against lower rear wall of rebox

outer wrapper with exhaust port directed upward

and thermodisc positioned up near replace bot-

tom. Thermodisc must be oriented near replace

bottom as shown in Figure 28 in order to sense

temperature and properly operate. Blower will

be held in position against back wall by magnets

incorporated onto blower housing (see Figure

28).

4. Be certain that all wire terminals are securely

attached to terminals on blower motor and

thermal switch, and that screw for thermodisc

bracket and green ground wire is tight.

5. Mount speed control box against mounting plate

provided in lower replace cavity by placing

plastic control shaft forward through round hole

(see Figure 26, page 18).

6. While supporting speed control, secure control

shaft with lock nut by pushing and turning lock

nut with pliers clockwise until it is tight against

mounting plate. Place control knob provided on

shaft (see Figure 26, page 18).

7. Check to make sure power cord is completely

clear of blower wheel and that no other foreign

objects are in blower wheel. Also double check

all wire leads and make sure wire routing is not

pinched or in a precarious position. Correct ac-

cordingly.

8. Turn on power to duplex outlet if previously

turned off per warning in column 1, page 18.

9. Plug in blower power cord to duplex outlet.

10. Blower will only run when speed control knob

is in ON position and thermal switch senses

temperature after replace begins to heat up.

Blower speed can be adjusted by rotating control

knob. To turn off, turn knob fully counterclockwise

until it clicks off. If blower is ON and has been

running with replace operating, blower will

continue to run for a short time after replace

has been turned off. As thermal switch cools

down, blower shuts down automatically.

Figure 28 - Blower Model BKT

Black

Wire

Phillips

Screw

Blue Wire

Ring

Terminal on

Green Wire

White Wire

Thermal

Switch

Thermal

Switch

Bracket

Power Cord

Air Flow

Direction

Magnetic

Strips

Side View Firebox Bottom

Route BKT Blower

Through This Area

Thermodisc

Air Flow

Direction

Magnets

Blower

www.fmiproducts.com

111250-01F20

11. Peel off backing paper and stick supplied

wiring diagram decal on rebox bottom

approximately 12" in front of blower (see

Figure 27, page 19).

Blower Wiring Diagram

CAUTION: Label all wires

prior to disconnection when

servicing controls. Wiring errors

can cause improper and dan-

gerous operation. Verify proper

operation after servicing.

FIREPLACE

INSTALLATION

Continued

Figure 29 - Blower Wiring Diagram for

Thermostat-Controlled Models

Blue

V a riable

Fan Switch

(N.O.)

Green

White

1 1 0/115

V. A.C.

Blower

Motor

Black

Off

Black

INSTALLING GAS PIPING TO

FIREPLACE LOCATION

WARNING: A qualified

service person must connect

replace to gas supply. Follow

all local codes.

CAUTION: For propane/LP

units, never connect fireplace

directly to the propane/LP supply.

This heater requires an external

regulator (not supplied). Install

the external regulator between the

replace and propane/LP supply.

WARNING: For natural

gas, never connect heater to

private (non-utility) gas wells.

This gas is commonly known

as wellhead gas.

Installation Items Needed

Before installing replace, make sure you have the

items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

• approved exible gas line with gas connector

(if allowed by local codes)

* A equipment shutoff valve with 1/8" NPT tap is

an acceptable alternative to test gauge connec-

tion. Purchase the equipment shutoff valve from

your retailer.

For propane/LP connection only, the installer must

supply an external regulator. The external regula-

tor will reduce incoming gas pressure. You must

reduce incoming gas pressure to between 11" and

14" of water. If you do not reduce incoming gas

pressure, replace regulator damage could occur.

Install external regulator with the vent pointing

down as shown in Figure 30. Pointing the vent

down protects it from freezing rain or sleet.

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of

1/2" inside diameter or greater to

allow proper gas volume to re-

place. If pipe is too small, undue

loss of volume will occur.

Figure 30 - External Regulator with Vent

Pointing Down (Propane/LP Only)

Propane/LP

Supply Tank

External

Regulator

Vent

Pointing

Down

Page is loading ...

Desa Tech CTDV36NR-A Owner's manual

Brand: Desa Tech

Model: CTDV36NR-A

Category: Fireplaces

Type: Owner's manual

Download PDF

report

Desa Tech CTDV36NR-A Owner's manual

Desa Tech CTDV36NR-A Owner's manual

Related papers

Other documents