Christie FHD552-X User manual

Brand: Christie

Model: FHD552-X

Category: TVs & monitors

Type: User manual

FHD552-X LCD Panel

User Manual

020-000741-04

FHD552-X LCD Panel

User Manual

020-000741-04

NOTICES

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this

document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary

depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based

on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied

warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection

with the performance or use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie.

In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the

warranty does not cover:

a. Problems or damage occurring during shipment, in either direction.

b. Projector lamps (See Christie’s separate lamp program policy).

c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a Christie lamp supplied by

Christie or an authorized distributor of Christie lamps.

d. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or

use of a product with any non-Christie interface device.

e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an unauthorized distributor of

Christie lamps, replacement parts or components including, without limitation, any distributor offering Christie lamps, replacement parts or

components through the internet (confirmation of authorized distributors may be obtained from Christie).

f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other natural disaster.

g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christie

authorized repair service provider.

h. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified

or approved by Christie for such use.

i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is unrelated to the projector.

j. For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use” which means the LCD

projector is not used more than 8 hours a day, 5 days a week.

k. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected

from precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient

temperature set forth in the specifications for such product.

l. Image retention on LCD flat panels.

m.Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product

sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is

located or (ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance section for specific

maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance with the maintenance schedule specified

by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at the user’s own expense.

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적

으로 합니다 .

Environmental

Theproductisdesignedandmanufacturedwithhigh‐qualitymaterialsandcomponentsthatcanberecycledandreused.

This symbol meansthatelectricaland

electronicequipment,attheirend‐of‐life,shouldbedisposedofseparatelyfromregularwaste.Pleasedisposeoftheproductappropriatelyandaccordingtolocal

regulations.IntheEuropeanUnion,thereareseparatecollectionsystemsforusedelectricalandelectronicproducts.Pleasehelpustoconservetheen

vironmentwe

livein!

FHD552-X LCD Panel User Manual 5

020-000741-04 Rev. 1 (07-2016)

Table of Contents

Package Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Handling and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Target Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Textual and Graphic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Description, Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Key Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Display at a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Input Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Notes on Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Notes on Remote Control Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Locking and Unlocking the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Handling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Ambient Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Mounting the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Connections to the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Connecting a Control System or PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

IR Extender Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Connecting Source Components to the Display . . . . . . . . . . . . . . . . . . . . . . . . .23

Setting Up a Video Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

FHD552-X LCD Panel User Manual 6

020-000741-04 Rev. 1 (07-2016)

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Turning on the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Changing the OSD Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Avoiding Image Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Using the On-Screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Using the Picture-in-Picture (PIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Maintenance and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

RS232 Connection and Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Command and Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Command and Response Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Serial Command List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Power control and input sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Display adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Other controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Using Video Wall Toolbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Using Discrete IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

IR Command Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

IR Control Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Supported Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Overall Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

FHD552-X LCD Panel User Manual 7

020-000741-04 Rev. 1 (07-2016)

Package Handling

Unpacking

Each LCD panel is packed inside a box carton. To protect the panel during transportation, additional

packing material has been placed within the carton.

1. Before unpacking, prepare a stable, level and clean surface near a wall outlet for your LCD

panel.

2. Set the box in an upright position and pull out the white carton locks.

3. Lift up the top cover carton.

4. Remove the ESD bag before removing the display from the bottom tray carton.

Failure to comply with the

following could result in death

or serious injury:

• Do not drop the panel (even

a short distance), or apply

pressure to the sides of the

bezel. The small size of the

bezel, which enables

minimal image-to-image

gaps, means there is

reduced protection of the

LCD glass and components.

Dropping the panel or

applying unnecessary force

to the sides of the bezel will

result in permanent

damage.

• To avoid serious injury and/

or serious damage to the

LCD panel, moving the

panel requires at least two

people. Hold the white

handles on the shipping

package when moving/

shipping.

• Extreme care must be taken

when pushing the mounted

display into its locked

position. Always handle the

display on the opposing

corners of the frame to

avoid direct contact with

the LCD glass.

Due to the delicate nature of the display, we strongly recommend that you use the

provided packing materials and secure the package onto a pallet during shipment.

Package Handling

FHD552-X LCD Panel User Manual 8

020-000741-04 Rev. 1 (07-2016)

Handling and Care

To avoid damaging your LCD panel, follow these guidelines when

handling or moving the panel:

• Always use the handles on the back of the LCD panel. Do not

hold onto the frame when transporting.

• Two people are required when moving or raising the LCD

panel. Use both hands, one positioned on the top handle and

the other on the bottom handle.

• Hold and support the LCD panel at each side and keep at an

even height above the ground.

• Do not twist or bend the panel.

• Use a cart to move several panels at one time.

• When the panel is sitting on a surface, do not tilt it more than

10° to avoid damaging the screen.

Cleaning

Use a cloth dampened with water or methyl alcohol to clean the screen surface. We recommend

that you keep the protective plastic sheet shipped with the panel to replace it each time the panels

are packed and shipped.

Make sure the power connector and any other cables are unplugged before moving the

product. Failure to comply could result in minor or moderate injury.

Unplug the power cord before cleaning the LCD panel. Do not use a liquid, spray cleaners,

or any abrasive cleaners to clean the LCD panel. Failure to comply may result in equipment

damage.

FHD552-X LCD Panel User Manual 9

020-000741-04 Rev. 1 (07-2016)

Introduction

About This Manual

This User Manual describes how to install, set up and operate the FHD651-P and FHD651-T LCD

Panels.

Target Audience

The manufacturer has prepared this manual to help end users get the most out of the display.

The manufacturer has made every effort to ensure that this manual is accurate as of the date it was

printed. However, because of ongoing product improvements and customer feedback, it may

require updating from time to time.

Textual and Graphic Conventions

Text Conventions

The following conventions are used in this manual, in order to clarify the information and

instructions provided:

• Remote and built-in keypad button identifiers are set in upper-case bold type; for example,

“Press EXIT to return to the previous menu.”

• Computer input (commands you type) and output (responses that appear on-screen) is shown

in monospace (fixed-width) type; for example: “To change the aspect ratio to Letterbox, type

07 00 02 41 53 50 03 08 <Enter>.”

• All keys with functional names are initial-capped, set in bold type and enclosed in angle

brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc> and <Tab>.

• <Enter> indicates that you may press either the RETURN or ENTER key on your keyboard if it

has both keys.

In addition to these conventions, underlining, boldface and/or italics are occasionally used to

highlight important information, as in this example:

A carriage return must be used after each command or string.

Introduction

FHD552-X LCD Panel User Manual 10

020-000741-04 Rev. 1 (07-2016)

Graphic Conventions

These symbols appear in numerous places throughout the manual, to emphasize points that you must

keep in mind to avoid problems with your equipment or injury:

TIPS highlight time-saving short cuts and helpful guidelines for using certain features.

NOTICE emphasize text with unusual importance or special significance. They also provide

supplemental information.

CAUTIONS alert users that a given action or omitted action can degrade performance or

cause a malfunction.

WARNINGS appear when a given action or omitted action can result in damage to the

equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or death.

Using This Manual

Use the following table to locate the specific information you need in this manual.

If you need... ... Turn to page:

General information about the FHD651-P and

FHD651-T LCD Panels

Installation instructions 18

First-time configuration instructions 31

Advanced configuration instructions 40

Troubleshooting tips 46

Product specifications 63

Introduction

FHD552-X LCD Panel User Manual 11

020-000741-04 Rev. 1 (07-2016)

Description, Features and Benefits

The FHD651-P and FHD651-T LCD Panels is a cutting-edge direct-view LCD that, when tiled with

multiple units, can create enormous images in multiple configurations. The display combines a

simple and slim design with unparalleled image quality with configurable I/O to provide a perfect

building block for large-format video walls, which are idea in digital signage and control-room

applications.

Key Features and Benefits

The display offers these key features and benefits:

• Full-HD Native Resolution: 1920 x 1080 (16:9 Native Aspect Ratio)

• High Brightness: Up to 500 nits

• 178-degree Viewing Angle

• DisplayPort 1.1a, HDMI and DVI Inputs with High-bandwidth Digital Content Protection (HDCP)

• Video Signal Looping

• Direct LED Backlight

• Video Wall Toolbox software [included] simplifies setting up a large video wall, with up to 25

displays, using a Windows PC

• Portrait- and Landscape-Mode Compatible

Parts List

Your display is shipped with the following items. If any items are missing or damaged, please

contact your dealer.

• FHD552-X LCD Panel

• Remote Control Unit and batteries

• AC Power cord

•DVI Cable

• RS232 Communications Cable

• RS485 Communications Cable

•IR Extender Cable

• Video Wall ToolBox Installation CD

FHD552-X LCD Panel User Manual 12

020-000741-04 Rev. 1 (07-2016)

Controls and Functions

Display at a Glance

The illustration below shows the key display components, and the paragraphs that follow describe

them.

1. HANDLES

Always use the handles when carrying the display. DO NOT touch or hold the screen face.

2. MAIN POWER SWITCH

Connects or disconnects the display panel from the AC power source.

3. STATUS LED

Lights orange to indicate that the display is in standby mode; blinks orange if no input signal is

present; off if the main power switch is set to off.

Controls and Functions

FHD552-X LCD Panel User Manual 13

020-000741-04 Rev. 1 (07-2016)

4. KEYPAD

You can use the keypad instead of the remote control unit to operate the

on-screen display (OSD) controls. The keypad operates as follows:



On/Standby ( )



Press once to toggle from standby mode to on mode. Press it again to

return to standby mode. 



SOURCE

To select a source, press the SOURCE button repeatedly (with no menus

visible on-screen). 



When a menu is visible on-screen, this button operates identically to the

right-arrow (or ENTER) button on the display remote control unit. 



When a menu is visible on-screen, this button operates identically to the

left-arrow button on the display remote control unit.



/ 

When a menu is visible on-screen, these buttons operate identically to the

up- and down-arrow buttons on the display remote control unit.



MENU/EXIT

Press this button to access the on-screen display (OSD) controls, or to exit

the current menu and return to the previous one.

SOURCE

MENU/EXIT

Controls and Functions

FHD552-X LCD Panel User Manual 14

020-000741-04 Rev. 1 (07-2016)

Input Panel

The illustration below shows the display input panel.

1. Power Input (100 to 240 VAC)

Connect the display to power here.

2. DVI-D Out (HDCP-compliant)

VESA-standard digital video output from the display to the next display in a video wall.

3. VGA Out (15-pin D-Sub)

VESA-standard analog video output from the display to the next display in a video wall.

4. DisplayPort

DisplayPort 1.1a and DisplayPort-HDCP 1.1 compliant, SD/HD input for connecting SDTV, EDTV

or HDTV component video sources.

5. HDMI 1, HDMI 2

Two (2) HDCP-compliant digital video inputs for connecting HDMI or DVI sources.

SOURCE

MENU/EXIT

Controls and Functions

FHD552-X LCD Panel User Manual 15

020-000741-04 Rev. 1 (07-2016)

6. DVI-D In (HDCP-compliant)

VESA-standard digital video input from a personal computer, or digital video from a DVD player

or HD set-top box.

7. VGA In (15-pin D-Sub)

For connecting components that have RGB or component output jacks such as a personal

computer or external DTV decoder (a break-out cable is needed for BNC-type connection).

8. PC Audio In 

Connect the audio output from a personal computer here.

9. IR Extender

Connect the IR Extender cable provided with the display to this input.

10. Audio Out 

For connecting external, powered speakers or an external audio receiver/amplifier.

11. Component

Standard- or high definition (up to 1080p), YPrPb component video input.

12. Comp. Audio

Stereo audio input from the Component video source.

13. S-Video

Standard S-video input for connecting a VCR, camcorder, gaming console, Super VHS (S-VHS)

VCR or other S-video source.

14. Video

Standard composite input for connecting a VCR, camcorder, gaming console or other composite

video source.

15. Video / S-V Audio

Stereo audio input from the Composite or S-video source.

16. RS232C In

A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control

system.

17. RS485 In

A female, 8-pin RJ-45 connector that connects to the previous display in a video wall.

18. RS485 Out

A female, 8-pin RJ-45 connector that connects to the next display in a video wall.

If both the Composite and S-video inputs are connected to sources, the S-video input takes

precedence.

Controls and Functions

FHD552-X LCD Panel User Manual 16

020-000741-04 Rev. 1 (07-2016)

Remote Control Unit

The illustration below shows the display remote control, and the table that follows describes its

functionality.

Controls and Functions

FHD552-X LCD Panel User Manual 17

020-000741-04 Rev. 1 (07-2016)

Label Description

1 Turns the monitor on and off

2 INFO Provides source and resolution information

3 VGA Selects the PC RGB source

DVI Selects the PC DVI source

HDMI1 Selects the HDMI source 1

COMP Selects the Component source

AV Selects the Composite Video source

HDMI2 Selects the HDMI source 2

4 P-POSITION Selects the PIP position

DISPLAYPORT Select the DisplayPort source

PIP Turns the PIP feature on and off

S-V Selects the S-video source

5 P-SOURCE Selects the secondary sub-source

6 SWAP Swaps the main and PIP source

7 MENU Opens the monitor’s on-screen menu system. When

the menu system is already open, pressing this

button will select the previous submenu

, , ,

Navigates through submenus and settings

8 ENTER Selects highlighted menu choices

9 EXIT Closes the menu system

10 SCALING Selects each aspect ratio, in sequence: Full Screen,

Native, Letter Box and Pillar Box

FREEZE Freezes the current source image

MUTE Turns off the sound

BRIGHT Adjusts the brightness

CONTRAST Adjusts the contrast

AUTO Auto adjustment of VGA source

SOURCE Selects each source, in sequence

VOLUME- Decreases the sound volume

VOLUME+ Increases the sound volume

FHD552-X LCD Panel User Manual 18

020-000741-04 Rev. 1 (07-2016)

Installation

Remote Control

To install batteries in the remote control:

1. Press down the tab on the cover and pull the cover up.

2. Insert the included batteries. Ensure that the polarities correctly match the and markings

inside the battery compartment.

3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in

place.

Notes on Batteries

• Make sure that the battery polarities are correct when installing the batteries.

• Do not mix an old battery with a new one or different types of batteries.

• If you will not use the remote control for a long time, remove the batteries to avoid damage

from battery leakage.

• Do not expose batteries to excessive heat such as from sunshine, fire or the like.

Notes on Remote Control Operation

• Make sure that there is nothing obstructing the infrared beam between the remote control and

the IR receiver on the display.

• If the effective range of the remote control decreases, or it stops working, replace the batteries

with new ones.

• The remote control may fail to operate if the infrared remote sensor is exposed to bright

sunlight or fluorescent lighting.

• Ambient conditions may possibly impede the operation of the remote control. If this happens,

point the remote control at the display, and repeat the operation.

Installation must be performed by a qualified custom video installation specialist.

Installation

FHD552-X LCD Panel User Manual 19

020-000741-04 Rev. 1 (07-2016)

Locking and Unlocking the Remote Control

You can lock the remote control buttons to prevent unauthorized persons from changing settings on

the display. To do this, press ENTER, ENTER, EXIT, EXIT, ENTER and EXIT, in sequence. To

unlock a locked remote control unit, use the same sequence of button presses.

Quick Setup

Here is a quick overview of the display installation process. The sections following this one provide

detailed instructions.

Installation Considerations

Proper installation of your display will ensure a satisfying viewing experience. Whether you are

installing a display temporarily or permanently, you should take the following into account to ensure

your display performs optimally.

Handling Guidelines

Super-narrow bezel displays are inherently very fragile devices. To avoid damaging your LCD panel,

follow these guidelines when handling or moving the panel. Please note that damage die to

improper handling is not covered under warranty.

• Always use the handles on the back of the LCD panel. Do not hold the display by its edges

(outer bezel).

• Two people are required when moving or raising the LCD panel. Use both hands, one positioned

on the top handle and the other on the bottom handle.

Step Procedure For Details, Refer to

page...

1 Mount the display(s) on a wall (optional) 20

2 Connect other external equipment to the display (optional):

• Automation/control system (RS232 or Ethernet)

• IR extender

3 Connect signal sources to the display 23

4 For video wall installations, connect video cables and control cables to each

display in a series (optional)

5 Apply power to the display 26

6 Change the OSD language (optional) 28

7 Display calibration: adjust the following for each input:

• Aspect ratio • Color level

• Brightness • Tint

• Contrast • Input position

• Color temperature and white balance

Installation

FHD552-X LCD Panel User Manual 20

020-000741-04 Rev. 1 (07-2016)

• Do not twist or bend the panel.

• Hold and support the LCD panel at each side and keep at an even height above the ground.

• Use a cart to move multiple panels at one time.

• When the panel is sitting on a surface, do not tilt it more than 10° to avoid damaging the

screen.

Ambient Heat

Keep the ambient temperature constant and below 40°C (104°F). Keep the display away from

heating and/or air conditioning vents.

Ventilation

If you are mounting the display in an enclosure, leave sufficient space on all sides between it and

surrounding objects, as shown below. This allows heat to disperse, maintaining the proper

operating temperature. For very thin installations, to mount the display close to a wall it may be

necessary to remove the handles prior to installation.

Mounting the Display

You can mount the display on a wall.

If you do decide to wall-mount the display, ensure that the wall-mount bracket is installed

according to the instructions included with it. The wall must be capable of supporting a redundant

weight factor three (3) times the weight of the display, or be reinforced.

Wall

15 mm

(0.59

)

Page is loading ...

Christie FHD552-X User manual

Brand: Christie

Model: FHD552-X

Category: TVs & monitors

Type: User manual

Download PDF

report

Christie FHD552-X User manual

Christie FHD552-X User manual

Related papers

Other documents