Omnitron Systems Technology FlexCeiver 10B2 User manual

Brand: Omnitron Systems Technology

Model: FlexCeiver 10B2

Category: Network media converters

Type: User manual

This manual is also suitable for

4220

Omnitron Systems Technology FlexCeiver 10B2 can be used to enhance networking media connectivity using 10BaseFL with single-mode (SM) and multimode (MM) fiber, 10Base-2 thin coax and 10Base-T twisted pair (UTP). It can be attached to a PC (or a workstation), a hub, or a switch, and provides a switch selectable coax line termination mode that allows an RG58 type coax cable to be terminated using an internal 50 ohm termination element.

DOC No. 040-04220-001 FlexCiever 10B2, Page 1/2

FlexCeiver

10B2 User Instructions

Description:

The FlexCeiver

family of transceivers are compatible

with IEEE 802.3 and Ethernet Versions 1.0 / 2.0. They

enhance networking media connectivity using 10Base-

FL with single-mode (SM) and multimode (MM) fiber,

10Base-2 thin coax and 10Base-T twisted pair (UTP).

All FlexCeivers have a 15-pin AUI connector that attaches

to a mating AUI connector mounted on hosting Ethernet

DTE equipment such as a workstation or a PC, or on a

repeater such as a hub or a switch.

This FlexCeiver 10B2 model is described here:

Model Maximum Distance Station Count

4220 185 meters / 606 ft. 30 maximum

The 4220 model provides a switch selectable coax line

termination mode that allows a RG58 type coax cable to

be terminated using an internal 50 ohm termination ele-

ment. This should be used only when connecting the

FlexCeiver at the end of a coax segment. It eliminates

the need for an external “T” connector and a termination

element. Note that this termination must be disabled

when the FlexCeiver is not at the end of the cable.

Mounting:

Insert the Omnitron FlexCeiver 10B2 into the 15-pin AUI

port on a PC, workstation, hub or switch; slide the con-

nector latch locking it into place. If an AUI cable is used,

it is limited to 50 meters (164 ft.). If connecting the

FlexCeiver at the end of a coax segment, attach the coax

cable directly into the FlexCeiver’s BNC coax connector.

If connecting along the coax line (not at the end), use a

“T” connector to tap into the cable. Note that the total

length of the cable must not exceed 185 meters (606 ft.)

and the number of stations on the coax segment must

not exceed 30 stations (per IEEE 802.3 specification).

Switch Settings:

“SQE” switch: When attaching to a PC (or a worksta-

tion), the SQE switch should be set to “SQE Enable”

(factory setting). When connecting to a hub or a switch,

it should be set to “SQE Disable.”

“Termination” switch: When attaching anywhere along

a coax cable except at the end, the Termination switch

should be set to “Termination Disabled” (factory setting).

When attaching to the end of a cable, it can be set to

“Termination Enabled.” Note that when the switch is set

to “Termination Enabled,” an external termination ele-

ment must not be attached.

LED indicators:

LED Color Description

Power On Green Power applied from attached unit

SQE Enable Yellow “SQE Enable” indicator

Technical Support:

If you encounter problems in installing or maintaining

this product, contact Omnitron Technical Support:

Phone: (949) 250-6510

Fax: (949) 250-6514

Email: [email protected]

Address: Omnitron Systems Technology, Inc.

27 Mauchly #201

Irvine, CA 92618 USA

User Warranty Registration

Please complete both sides and mail or fax this registration form to:

Omnitron Systems Technology, Inc.

27 Mauchly #201

Irvine, CA 92618 USA

Fax: (949) 250-6514

Name: _________________________________________________

Company: ______________________________________________

Address: ______________________________________________

______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Phone: ____________________ Fax: _______________________

E-mail: _________________________________________________

Please complete both sides of this form

FlexCeiver

10B2 User Instructions

Description:

The FlexCeiver

family of transceivers are compatible

with IEEE 802.3 and Ethernet Versions 1.0 / 2.0. They

enhance networking media connectivity using 10Base-

FL with single-mode (SM) and multimode (MM) fiber,

10Base-2 thin coax and 10Base-T twisted pair (UTP).

All FlexCeivers have a 15-pin AUI connector that attaches

to a mating AUI connector mounted on hosting Ethernet

DTE equipment such as a workstation or a PC, or on a

repeater such as a hub or a switch.

This FlexCeiver 10B2 model is described here:

Model Maximum Distance Station Count

4220 185 meters / 606 ft. 30 maximum

The 4220 model provides a switch selectable coax line

termination mode that allows a RG58 type coax cable to

be terminated using an internal 50 ohm termination ele-

ment. This should be used only when connecting the

FlexCeiver at the end of a coax segment. It eliminates

the need for an external “T” connector and a termination

element. Note that this termination must be disabled

when the FlexCeiver is not at the end of the cable.

Mounting:

Insert the Omnitron FlexCeiver 10B2 into the 15-pin AUI

port on a PC, workstation, hub or switch; slide the con-

nector latch locking it into place. If an AUI cable is used,

it is limited to 50 meters (164 ft.). If connecting the

FlexCeiver at the end of a coax segment, attach the coax

cable directly into the FlexCeiver’s BNC coax connector.

If connecting along the coax line (not at the end), use a

“T” connector to tap into the cable. Note that the total

length of the cable must not exceed 185 meters (606 ft.)

and the number of stations on the coax segment must

not exceed 30 stations (per IEEE 802.3 specification).

Switch Settings:

“SQE” switch: When attaching to a PC (or a worksta-

tion), the SQE switch should be set to “SQE Enable”

(factory setting). When connecting to a hub or a switch,

it should be set to “SQE Disable.”

“Termination” switch: When attaching anywhere along

a coax cable except at the end, the Termination switch

should be set to “Termination Disabled” (factory setting).

When attaching to the end of a cable, it can be set to

“Termination Enabled.” Note that when the switch is set

to “Termination Enabled,” an external termination ele-

ment must not be attached.

LED indicators:

LED Color Description

Power On Green Power applied from attached unit

SQE Enable Yellow “SQE Enable” indicator

Technical Support:

If you encounter problems in installing or maintaining

this product, contact Omnitron Technical Support:

Phone: (949) 250-6510

Fax: (949) 250-6514

Email: [email protected]

Address: Omnitron Systems Technology, Inc.

27 Mauchly #201

Irvine, CA 92618 USA

User Warranty Registration

Please complete both sides and mail or fax this registration form to:

Omnitron Systems Technology, Inc.

27 Mauchly #201

Irvine, CA 92618 USA

Fax: (949) 250-6514

Name: _________________________________________________

Company: ______________________________________________

Address: ______________________________________________

______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Phone: ____________________ Fax: _______________________

E-mail: _________________________________________________

Please complete both sides of this form

DOC No. 040-04220-001 FlexCiever 10B2, Page 2/2

Warning

The operating description in this Instruction Manual is

for use by qualified personnel only. To avoid electrical

shock, do not perform any servicing of this unit other

than that contained in the operating instructions, unless

you are qualified and certified to do so by Omnitron Sys-

tems Technology, Inc.

Caution

All user-required operations can be performed without

opening the unit. Never attempt to open or remove the

cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser

against defects in material and workmanship for a pe-

riod of TWO YEARS from the date of shipment. A LIFE-

TIME warranty may be obtained by the original purchaser

by REGISTERING this product with Omnitron within 90

days from the date of shipment. TO REGISTER, COM-

PLETE AND MAIL OR FAX THE REGISTRATION POR-

TION OF THIS INSTRUCTION MANUAL TO THE INDI-

CATED ADDRESS. During the warranty period,

Omnitron will, at its option, repair or replace a product

which is proven to be defective.

For warranty service, the product must be sent to an

Omnitron designated facility, at Buyer’s expense. Omni-

tron will pay the shipping charge to return the product to

Buyer’s designated US address using Omnitron’s stan-

dard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects result-

ing from improper or inadequate use and/or maintenance

of the equipment by Buyer, Buyer-supplied equipment,

Buyer-supplied interfacing, unauthorized modifications

or tampering with equipment (including removal of equip-

ment cover by personnel not specifically authorized and

certified by Omnitron), or misuse, or operating outside

the environmental specification of the product (includ-

ing but not limited to voltage, ambient temperature, ra-

diation, unusual dust, etc.), or improper site preparation

or maintenance.

No other warranty is expressed or implied. Omnitron

specifically disclaims the implied warranties of merchant-

ability and fitness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and

exclusive remedies. Omnitron shall not be liable for any

direct, indirect, special, incidental, or consequential dam-

ages, whether based on contract, tort, or any legal theory.

Form:040-04220-001 6/99

Notes:

____________________________

_____________________________

____________________________

User Warranty Registration

Please complete both sides and mail or fax this form to the address indicated on

the other side.

FlexCeiver Type: p 10FL p 10T p 10B2 p Other _________

Model: _________________________________________________

Serial Number: ______________ Purchase Date: ______________

Purchased From: _________________________________________

Address: ______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Comments and Suggestions: _______________________________

______________________________________________________

Please complete both sides of this form

Warning

The operating description in this Instruction Manual is

for use by qualified personnel only. To avoid electrical

shock, do not perform any servicing of this unit other

than that contained in the operating instructions, unless

you are qualified and certified to do so by Omnitron Sys-

tems Technology, Inc.

Caution

All user-required operations can be performed without

opening the unit. Never attempt to open or remove the

cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser

against defects in material and workmanship for a pe-

riod of TWO YEARS from the date of shipment. A LIFE-

TIME warranty may be obtained by the original purchaser

by REGISTERING this product with Omnitron within 90

days from the date of shipment. TO REGISTER, COM-

PLETE AND MAIL OR FAX THE REGISTRATION POR-

TION OF THIS INSTRUCTION MANUAL TO THE INDI-

CATED ADDRESS. During the warranty period,

Omnitron will, at its option, repair or replace a product

which is proven to be defective.

For warranty service, the product must be sent to an

Omnitron designated facility, at Buyer’s expense. Omni-

tron will pay the shipping charge to return the product to

Buyer’s designated US address using Omnitron’s stan-

dard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects result-

ing from improper or inadequate use and/or maintenance

of the equipment by Buyer, Buyer-supplied equipment,

Buyer-supplied interfacing, unauthorized modifications

or tampering with equipment (including removal of equip-

ment cover by personnel not specifically authorized and

certified by Omnitron), or misuse, or operating outside

the environmental specification of the product (includ-

ing but not limited to voltage, ambient temperature, ra-

diation, unusual dust, etc.), or improper site preparation

or maintenance.

No other warranty is expressed or implied. Omnitron

specifically disclaims the implied warranties of merchant-

ability and fitness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and

exclusive remedies. Omnitron shall not be liable for any

direct, indirect, special, incidental, or consequential dam-

ages, whether based on contract, tort, or any legal theory.

Form:040-04220-001 6/99

Notes:

____________________________

_____________________________

____________________________

User Warranty Registration

Please complete both sides and mail or fax this form to the address indicated on

the other side.

FlexCeiver Type: p 10FL p 10T p 10B2 p Other _________

Model: _________________________________________________

Serial Number: ______________ Purchase Date: ______________

Purchased From: _________________________________________

Address: ______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Comments and Suggestions: _______________________________

______________________________________________________

Please complete both sides of this form

Omnitron Systems Technology FlexCeiver 10B2 User manual

Brand: Omnitron Systems Technology

Model: FlexCeiver 10B2

Category: Network media converters

Type: User manual

This manual is also suitable for

4220

Download PDF

report

Omnitron Systems Technology FlexCeiver 10B2 User manual

This manual is also suitable for

Omnitron Systems Technology FlexCeiver 10B2 User manual

Related papers

Other documents