Cross Technologies 3115-72 Owner's manual
- Category
- Video converters
- Type
- Owner's manual
This manual is also suitable for
Cross Technologies 3115-72 is a block upconverter that converts 0.95 - 1.45 GHz to 7.25 - 7.75 GHz with a 6.3 GHz local oscillator. It features a maximum gain of +30 dB, adjustable in 0.5 dB steps, and a gain adjustment range of 30 dB. The device has a front panel LCD display for direct readout of gain and reference frequency, as well as pushbutton switches for easy control. It also includes a remote interface for monitoring and control via RS-232C/485 or Ethernet (optional).
Cross Technologies 3115-72 is a block upconverter that converts 0.95 - 1.45 GHz to 7.25 - 7.75 GHz with a 6.3 GHz local oscillator. It features a maximum gain of +30 dB, adjustable in 0.5 dB steps, and a gain adjustment range of 30 dB. The device has a front panel LCD display for direct readout of gain and reference frequency, as well as pushbutton switches for easy control. It also includes a remote interface for monitoring and control via RS-232C/485 or Ethernet (optional).
Instruction Manual
Model 3115-72
Block Upconverter
December 2013, Rev. 0
MENU
EXECUTE
MODEL 3115
CROSS TECHNOLOGIES INC.
1.20 - 7.50 GHZ
G=+10.0 REF AUTO-I
POWERREMOTE ALARM
UPCONVERTER
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment. Printed in USA.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
INSTRUCTION MANUAL
MODEL 3115-72 Block Upconverter
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
1.3 Monitor & Control Interface 5
2.0 Installation 8
2.1 Mechanical 8
2.2 Rear I/O’s 9
2.3 Front Panel Controls, Indicators 9
2.4 Operation 10
2.5 Menu Settings 11
3.0 Environmental Use Information 16
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies,
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s
option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall
not be liable for any special, indirect, or consequential damages. This warranty does not
cover parts or equipment which have been subject to misuse, negligence, or accident by the
customer during use. All shipping costs for warranty repairs will be prepaid by the
customer. There are not other warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
3115-72 Manual, Rev. 0 Page 2 12/09/13
MODEL 3115-72 Block Upconverter
1.0 General
1.1 Equipment Description
The 3115-72 Upconverter converts 0.95 - 1.45 GHz to 7.25 - 7.75 GHz (non-inverted) with a 6.3 GHz local
oscillator. The gain is +30 dB maximum and is adjustable in 0.5 ± 0.5 dB steps. Front panel LEDs provide
indication of Remote operation, PLL Alarm and DC Power. Gain and internal/external/Auto reference
frequency selection are controlled by front panel switches or remote selection (via RS-232C/485, standard;
Ethernet Optional) and are viewable on the LCD Display. Connectors are Type N female for the RF and BNC
female for the L-Band and external reference input and reference output. In AUTO, the 10 MHz reference stays
in external if the external level is +3 dBm, ±3 dB. The 3115 is powered by a 100-240 ± 10% VAC power
supply, and housed in a 1 3/4” X 19” X 14” rack mount chassis.
MENU
EXECUTE
MODEL 3115
CROSS TECHNOLOGIES INC.
1.20 - 7.50 GHZ
G=+10.0 REF AUTO-I
POWERREMOTE ALARM
UPCONVERTER
FRONT PANEL - 3115-72
AC
RF OUTPUT
GND
J101
J8
10 MHZ REF
OUTPUT
J11
ALARM
15 234
6789
J2
EXT 10 MHZ
INPUT
L-BAND
INTPUT
J1
J14
AUTO
INT
EXT
S1
REAR PANEL - 3115-72 (Shown with optional RJ45 Ethernet Connector)
FIGURE 1.1 3115-72 Front and Rear Panels
7.25
to
7.75
GHz
OUT
0.95
to
1.45
GHz
IN
1.5 GHz LP
CONTROLLER
G=+10.0 REF AUTO
6.3
GHz
EXT
10MHz
var
atten
INT
10MHz
3115-72 Block Diagram
AUTO
7.25-7.75 GHz
BP
FIGURE 1.2 3115-72 Block Diagram
3115-72 Manual, Rev. 0 Page 3 12/09/13
1.2 Technical Characteristics
*+0 to +50 degrees C; Specifications subject to change without notice.
3115-72 Manual, Rev. 0 Page 4 12/09/13
-50 dBm, FL -2 GHz to FL -0.9 GHz and FH +0.9 GHz to FH +2 GHz
S
p
urious
,
Out of Band
±1.0 dB
,
7.9 -8.4 GHz out
;
± 0.5 dB
,
40 MHz BW Fre
q
uenc
y
Re
p
onse
Channel Characteristics
LO Characteristics
±0.01
pp
m maximum oven tem
p
erature internal reference; external reference in
p
ut Fre
q
uenc
y
Accurac
y
Non-invertin
g
Fre
q
uenc
y
Sense
<-55 dBC for two carriers each at -10 dBm out, GAIN = +30 dB
Intermodulation
-55 dBC, FL -0.9 GHz to FL and FH to FH +0.9 GHz; FL= 7.9 GHz and FH = 8.4 GHz
S
p
urious
,
Out of Band
-55 dBC in band, -20 to -5 dBm out
S
p
urious, Inband
3 dBm, ± 3 dB, with Auto-detect
10 MHz Level In/Out
6.3 GHz LO Fre
q
uenc
y
> 60 dB, minimum Ima
g
e Re
j
ection
+30 dB ±1 dB, max.
g
ain; 30 dB ad
j
ustment in 0.5 ±0.5 Ste
p
s Gain, Max.
(
ad
j
ustment
)
BNC
(
female
),
50Ω L-Band Connector
19 inch
,
Standard Chassis
,
1.75” hi
g
h X 14.0” dee
p
Size
DB9 - NO or NC Contact Closure on Alarm Alarm / Remote Connector
BNC
(
female
),
75Ω works with 50 or 75 ohms 10 MHz Connectors
Other
100-24 ±10% VAC
,
47-63 Hz
,
45 watts maximum
Power
N-T
yp
e
(
female
),
50Ω RF Connector
Controls
,
Indicators
RS232C/RS485/422, 9600 baud
(
Ethernet O
p
tional
)
Remote
Direct Readout LCD;
p
ushbutton switches or remote Gain; Ext. Reference Selection
Green LED
,
Red LED
,
Yellow LED
,
Yellow LED Power
,
Alarm
,
Remote
,
Mute
TABLE 1.0 3115-72 Block Upconverter Specifications*
12 dB maximum
g
ain Noise Fi
g
ure, Maximum
-40 to -20 dBm In
p
ut Level Ran
g
e
0.95 to 1.45 GHz Fre
q
uenc
y
+5 dBm at maximum
g
ain Out
p
ut 1 dB Com
p
ression
-20 to -5 dBm Out
p
ut Level Ran
g
e
Out
p
ut Characteristics
In
p
ut Characteristics
7.25 to 7.75 GHz Fre
q
uenc
y
50Ω / 18 dB Im
p
edance / Return Loss
50Ω / 14 dB Im
p
edance / Return Loss
-110 -100 -85 -80 -70 -55
1M 100K 10K 1K 100 10
Standard dBC/
(
Hz
)
Phase Noise @ F
(
Hz
)
>
Available Connector O
p
tions, See Table 2.2, PG 9
Available O
p
tions
0 to +50 de
g
rees C O
p
eration
W31 -
L-Band / RF front
p
anel Monitors
(
-20 dBC
)
W7 -
Remote M&C Ethernet O
p
tions
Ethernet with SNMP
(
and MIB
)
Interface - W18
Ethernet
;
with Direct TCP/IP Interface
Ethernet with Web Browser Interface
- W28
- W8
1.3 Monitor and Control Interface
A) Remote Serial Interface
Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.
(RS-232C, RS-422, or RS-485 - option Q)
Connector: Rear panel, DB-9 male
J10 Pinouts (RS-232C/422/485)
Pinouts (RS-232C/422/485)
Pin Function
1 Rx-
2 Rx+ (RS-232C)
3 Tx+ (RS-232C)
4Tx-
5GND
6 Alarm Relay: Common
7 Alarm Relay: Normally Open
8 Not Used
9 Alarm Relay: Normally Closed
3115-72 Manual, Rev. 0 Page 5 12/09/13
Female DB-9
PC Com Port
Male DB-9
2
1
3
4
5
6
7
8
9
2
1
3
4
5
6
7
8
9
M&C Cable Diagram - Cross Technologies Frequency Converters and
Frequency Sources
B) Status Requests - Table 1.1 lists the status requests for the 3115-72 and briefly describes them.
* PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,
should be used ONLY when
RS-485, (OPTION-Q), is selected.
TABLE 1.1 3115-72 Status RRequests
Status Requests
Command Syntax * Description
Get Gain {aaSG} returns {aaSGxxx} where:
• xxx = Converter gain in 0.5 dB steps.
Get Internal 10 MHz Reference Offset {aaSO} Returns {aaSOxxxxx} where:
• xxxxxx = Internal 10 MHz reference frequency offset.
Get 10 MHz Reference Mode {aaSE} Returns {aaSEx} where:
• x = 0 if the converter's 10 MHz reference mode is set to Internal
• x = 1 if the converter's 10 MHz reference mode is set to External
• x = 2 if the converter's 10 MHz reference mode is set to Auto
Get Mute {aaSM} Returns {aaSMx} where:
• x = 0 if the converter's RF output is NOT muted (RF output is ON)
• x = 1 if the converter's RF output is muted (RF output is OFF)
Get 10 MHz Reference Status {aaSB} Returns {aaSBx} where:
• x = 0 if the currently selected 10 MHz reference is Internal
• x = 1 if the currently selected 10 MHz reference is External
Get IP Address {Si} Returns {Sixxx.xxx.xxx.xxx} where:
Options W8, W18, W28 only) • xxx.xxx.xxx.xxx = IP address
Get Subnet Mask {Ss} Returns {Ssxxx.xxx.xxx.xxx} where:
Options W8, W18, W28 only) • xxx.xxx.xxx.xxx = subnet mask
Get Product/Model info {Sv} Returns {Sv3115-72y..yverZZZZ} where:
• 3115-xx is the product model number
• y..y = list of options, if any
• '"ver" = separates model & options from firmware version
• ZZZZ = firmware version (e.g., 4.00)
Get Alarm Status {aaSA} Returns {aaSAx}where:
• x = 0 if alarm is off
• x = 1 if alarm is on
3115-72 Manual, Rev. 0 Page 6 12/09/13
C) Commands
Table 1.2 lists the commands for the 3115-72 and briefly describes them.
After a command is sent the 3115 sends a return “>” indicating the command has been received and executed.
General Command Format - The general command format is {CND...}, where:
{ = start byte
C = 1 character, either C (command) or S (status)
N = 1 character command or status request
D = 1 character or more of data (depends on command)
} = stop byte
* PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,
should be used ONLY when R
S-485, (OPTION-Q), is selected.
3115-72 Manual, Rev. 0 Page 7 12/09/13
TABLE 1.2 3115-72 Commannds
Commands
Command Syntax * Description
Set Gain {aaCGxxx} where:
• xxx = Converter gain in 0.5 dB steps.
Range: 000 to 300 where 300 = 30.0 dB
Example: {CG155} sets the converter's gain to +15.5dB
Set Internal 10 MHz Reference Offset {aaCOxxxxx} where:
• xxxxxx = Internal 10 MHz reference frequency offset.
Range: -2000 to +2000
Set 10 MHz Reference Mode {aaCEx} where:
• x = 0 if the converter's 10 MHz reference mode is set to Internal
• x = 1 if the converter's 10 MHz reference mode is set to External
• x = 2 if the converter's 10 MHz reference mode is set to Auto
Set Mute {aaCMx} where:
• x = 0 if the converter's RF output is NOT muted (RF output is ON)
• x = 1 if the converter's RF output is muted (RF output is OFF)
2.0 Installation
2.1 Mechanical
The 3115 is powered by a 100-240 ± 10% VAC power supply, and housed in a 1 3/4” X 19” X 14” rack mount
chassis. The 3115-72 can be secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the
3115-72 is assembled.
POWER
SUPPLY
FIGURE 2.0 3115-72 Mechanical Assembly
3115-72 Manual, Rev. 0 Page 8 12/09/13
2.2 Rear Panel Input/Output Signals
Figure 2.1 shows the input and output connectors on the rear panel.
J1 - INPUT
0.95 - 1.45 GHz,
-40 to -20 dBm
BNC Female Connector.
See Table 2.2
AC1 - POWER IN
AC input for switching power supply.
100-240 ±10% VAC, 47-63 Hz.
J101 - OUTPUT
7.25 -7.75 GHz,
-20 to 0 dBm
N-Type Female
See Table 2.2
J11 - ALARM
DB9 female connector.
See Table 2.1.
J8 - 10 MHz EXT REF OUTPUT
+3 ±3 dBm,
BNC Female Connector.
AC
GND
J2 - 10 MHz EXT REF INPUT
10 MHz external reference input,
+3 ±3 dBm, BNC Female Connector.
RF OUTPUT
J101
J8
10 MHZ REF
OUTPUT
J11
ALARM
15
234
6789
J2
EXT 10 MHZ
INPUT
L-BAND
INPUT
J1
J14
J14 - Ethernet Connector
RJ45 Ethernet Connector.
S1
S1 - SWITCH
NOT USED
EXTINT
AUTO
FIGURE 2.1 3115-72 Rear Panel I/Oʼs
TABLE 2.1 JJ10
TABLE 2.1 J10 Pinouts*
Pin Function
1 Rx-
2 Rx+ (RS-232C)
3 Tx+ (RS-232C)
4Tx-
5GND
6 Alarm Relay: Common
7 Alarm Relay: Normally Open
8 Not Used
9 Alarm Relay: Normally Closed
TABLE 2.22
2.2 Connector Optioons
Options
Option RF L-Band
-N 50Ω Type N 75Ω BNC
-NF 50Ω Type N 75Ω Type F
-NN 50Ω Type N 50Ω Type N
-S7 50Ω SMA 75Ω BNC
-SF 50Ω SMA 75Ω Type F
-SN 50Ω SMA 50Ω Type N
-SS 50Ω SMA 50Ω SMA
*Remote Serial Interface
Interface: DB-9 Male Protocol: RS-232C (RS-232C/422/485, Option Q),
9600 baud rate, no parity, 8 data bits, 1 start bit, 1 stop bit.
2.3 Front Panel Controls and Indicators
Figure 2.2 shows the front panel controls and indicators.
MENU
EXECUTE
1.20 > 7.50 GHZ
G=+10.0 REF AUTO-I
POWERALARM
S3 - MENU/EXECUTE BUTTON
Press this to get into Program mode
and to execute any changes.
DS6 - ALARM LED
Red LED indicates an
alarm condition.
S2 - VERT. TOGGLE
Vertical toggle switch that controls
values in the Menu items when in
program mode. Does not function in
the normal display mode.
S1 - HORIZ. TOGGLE
Horizontal toggle switch that
controls which values are being
adjusted. Does not function in the
normal display mode.
REMOTE
DS2 - POWER LED
Green LED indicates
presence of DC power
from power supply.
DS3 - REMOTE LED
Yellow LED indicates
remote operation.
LCD DISPLAY
Display shows current
mode and output level
in dBm or gain in dB.
FIGURE 2.2 3115-72 Front Panel Controls and Indicators
3115-72 Manual, Rev. 0 Page 9 12/09/13
2.4 Installation / Operation
2.4.1 Installing and Operating the 3115-72
1. Connect a -40 dBm to -20 dBm signal to L-Band IN, J1 (Figure 2.1).
2. Connect the RF OUT, J101, to the external equipment.
3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC connector on the back panel.
4. Set the gain (from 0 to +30, 0.5 ± 0.5 dB steps) for the desired output level.
Make sure the output stays within -20 to -5 dBm with the gain selected and the
input level provided. (See Section 2.5 Menu Settings).
5. Be sure DS2 (green, DC Power) is on and DS6 (red, Alarm) is off (Figure 2.2).
6.
AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot
in the drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot.
If a fuse continues to open, the power supply is most likely defective.
AC Fuse - 2 amp slow blow (Type T),
5 mm X 20 mm
FUSE DRAWER
SPARE FUSE
~
INPUT
100-240±
47-63 Hz
2A
FUSE
TYPE T 2A GDC
250
FOR 100 - 240 V~
~
FIGURE 2.3 Fuse Location and Spare Fuse
3115-72 Manual, Rev. 0 Page 10 12/09/13
2.5 Menu Settings
2.5.1 Functions
This section describes operation of the front panel controls. There are three operator switches, the LCD display
and alarm indicator LEDs. All functions for the equipment are controlled by these components. The functions
are (See Figure 2.4):
Power Up
Normal Display
Menu 1 Set Gain
Menu 2 Set Mute
Menu 3 Set Reference Mode
Menu 4 Set Reference Offset
Menu 5 Set Remote
Menu 6 Set Remote Interface
Menu 7 Set RS-485 Address
Save Menu When “R” is selected from any above menu or at the end.
Alarm indications appear on the LEDs (see Figure 2.2).
All program changes must start with the operation of the Menu/Execute switch and must also end with the
operation of the Menu/Execute switch verified by the “Save Settings?” Menu. If this sequence is not followed,
none of the changes will take effect. If programming is initiated and no operator action takes place for
approximately 30 seconds (before the final press of the Menu/Execute switch) the display will revert to its
previous status and you will need to start over.
3115-72 Manual, Rev. 0 Page 11 12/09/13
2.5.2. Power On Settings
NOTE: THE LAST OPERATING PARAMETERS OF A UNIT ARE RETAINED EVEN WHEN
POWER IS REMOVED. WHEN POWER IS RESTORED, THE UNIT WILL RETURN TO IT'S
PREVIOUS SETTINGS.
When power is first applied, the LCD display goes through three steps.
1. The LCD goes black to show all segments are functioning.
2. The Model and Software version will be displayed.
3115-72W18
Rev. 4.00
3. The present frequency and gain of the upconverter is shown.
1.20 - 7.50 GHz
G = +10.0 REF AUTO-I
The unit is now operational and ready for any changes the operator may desire.
2.5.3 Control Switches
1. Menu/Execute - Any change to the programming of the unit must be initiated by pressing the
Menu/Execute switch and completed by pressing the Menu/Execute switch.
2. Horizontal Switch - This switch is mounted so its movement is horizontal and moves the
display cursor left or right.
3. Vertical Switch - This switch is mounted so its movement is vertical and has two functions:
a. During gain changes, the vertical movement will raise or lower the number
in the direction of the arrows.
b. For other functions such Remote on/off, the vertical switch will alternately turn the function
on or off regardless of the direction operated.
3115-72 Manual, Rev. 0 Page 12 12/09/13
2.5.4 Gain Changes
When you get to this menu note that gain changes will be made as you make them but if you do not wish to
save the changes you have made, scroll to “R” and push the menu/Execute switch and select “NO” in the
“SAVE SETTINGS?” window or do not press the Menu/Execute switch; simply do nothing for
approximately 30 seconds, and the system will return to the normal operating mode.
NOTE: THE GAIN WILL CHANGE AS YOU ADJUST THE NUMBERS. HOWEVER, THE
VALUE WILL NOT BE STORED UNTIL YOU INDICATE YES IN THE SAVE SETTINGS
WINDOW. DO NOT SET A GAIN THAT WOULD EXCEED 0 dBm OR HAVE LESS
THAN -20 dBm OUTPUT LEVEL.
Press the Up/Down switch to change the gain in 0.5, 1, or 10 dB steps and then push the
Menu/Execute switch to get to the Save Settings Menu:
GAIN = +17.5
R
When the display indicates the value desired you can push the Menu/Execute switch to the next item
OR you can scroll to “R”, push the Menu/Execute switch to get to:
SAVE SETTINGS?
Y N
Selecting Y will save the new settings. Selecting N will revert to the previous settings.
Figure 2.4 (page 15) gives the menu items and how to make changes.
3115-72 Manual, Rev. 0 Page 13 12/09/13
2.5.5 Alarm Indications
An alarm condition will occur if any local oscillator phase lock loop (PLL) comes out of lock.
The Remote LED will light when you select the Remote mode.
2.5.6 10 MHz Reference Mode Operation
Internal Mode: The unit uses its own built-in 10 MHz OCXO. The Internal Reference is present on the
Reference Output Connector, J8. REF = INT appears on the front panel display.
External Mode: The unit uses a 10 MHz Reference that is connected to the External Reference Input, J2.
REF = EXT appears on the front panel display. The External 10 MHz Reference level
must be +3dBm, ±3dB. If the External 10 MHz signal does not meet the unit’s
specified parameters then the unit will not function properly. The External Reference
is present on the Reference Output connector, J8.
Auto Mode: The unit defaults to the External 10 MHz Reference as long as the level meets the +3dBm,
±3dB specification. REF = AUTO - E appears on the front panel display where the -E
indicates that the unit is using the External 10 MHz Reference. The External Reference is
present on the Reference Output connector, J8.
If the external 10 MHz Reference signal level is less than -1dBm, the unit switches to
Internal 10 MHz Reference. REF = AUTO -I appears on the front panel display
where -I indicates that the unit is using the Internal 10 MHz Reference. The Internal
10 MHz Reference is present on the reference output connector, J8.
3115-72 Manual, Rev. 0 Page 14 12/09/13
NORMAL DISPLAY
PUSHING MENU/EXECUTE SEQUENCE
3115-72W18
4.0
1.20 - 7.50 GHZ
G = +10.0 REF AUTO-I
SCROLL <>
SCROLL
PUSH BUTTON
PUSH BUTTON
Power Up 1:
Power Up 2:
Normal Display
Menu 1 Set Gain
Menu 2 Set Mute
Menu 3 Set Reference Mode
Menu 4 Set Reference Offset
Menu 5 Set Remote
Menu 6 Set Remote Interface
Menu 7 Set RS485 Address
Save? When go to end
SCROLL <>
SCROLL
PUSH BUTTON
SCROLL <>
SCROLL
PUSH BUTTON
R
R
R
SCROLL <>
SCROLL
PUSH BUTTON
R
SCROLL <>
SCROLL
PUSH BUTTON
GAIN = 15.5
MUTE = ON
REF MODE = AUTO
INTERNAL FREQ ADUST
OFFSET = -1225
INTERFACE = RS232
RS485 ADDRESS = 0
R
R
SAVE SETTINGS? Y N
SCROLL <>
SCROLL
PUSH BUTTON
SCROLL <>
SCROLL
PUSH BUTTON
REMOTE = ON
R
SCROLL <>
SCROLL
PUSH BUTTON
= = = IP Addr = = =
192.168.123.002
ON POWER UP (1)
ON POWER UP (2)
FIGURE 2.4 Menu Display and Sequences
3115-72 Manual, Rev. 0 Page 15 12/09/13
3.0 Environmental Use Information
A. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your equipment rack.
B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C. Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between units
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connection to the
Branch (use of power strips).
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
3115-72 Manual, Rev. 0 Page 16 12/09/13
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
Printed in USA
3115-72 Manual, Rev. 0 Page 17 12/09/13
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Cross Technologies 3115-72 Owner's manual
- Category
- Video converters
- Type
- Owner's manual
- This manual is also suitable for
Cross Technologies 3115-72 is a block upconverter that converts 0.95 - 1.45 GHz to 7.25 - 7.75 GHz with a 6.3 GHz local oscillator. It features a maximum gain of +30 dB, adjustable in 0.5 dB steps, and a gain adjustment range of 30 dB. The device has a front panel LCD display for direct readout of gain and reference frequency, as well as pushbutton switches for easy control. It also includes a remote interface for monitoring and control via RS-232C/485 or Ethernet (optional).
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Cross Technologies 3115-73 Owner's manual
-
-
-
-
-
-
-
-
-