Sansui HDPDP4200 Owner's manual

Brand: Sansui

Model: HDPDP4200

Category: Plasma TVs

Type: Owner's manual

This manual is also suitable for

HDPDP4200A

42” WIDE PLASMA DISPLAY

HDPDP4200

OWNER’S MANUAL

Before operating the unit, please read this manual thoroughly.

ATTENTION

If you purchase a universal remote control from your local retailer, please contact the remote

manufacturer for the required programming code.

IF CONTACT WITH CUSTOMER SERVICE IS REQUIRED

PLEASE HAVE THE MODEL NUMBER READY PRIOR TO THE CALL

CUSTOMER SERVICE – 1-800-289-0980

ORION WEBSITE

FOR INFORMATION ON OUR OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE AT

www.orionsalesinc.com

3V00101A_En_cover 6/2/05, 4:40 PM1

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

The lightning flash with arrowhead

symbol, within an equilateral triangle

is intended to alert the user to the

presence of uninsulated dangerous

voltage within the product's enclosure

that may be of sufficient magnitude to

constitute a risk of electric shock.

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servic-

ing) instructions in the literature

accompanying the appliance.

CAUTION:TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

FCC Declaration of Conformity Compliance Statement (Part 15):

The Sansui HDPDP4200, WIDE PLASMA DISPLAY complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

The party responsible for compliance to these rules is:

ORION SALES, INC

HIGHWAY 41 ORION PLACE, PRINCE, PRINCETON, INDIANA 47670

Ph: 1-800-289-0980

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with

the FCC Rules could void the user's authority to operate this equipment.

3V00101A_En_p02-11 6/2/05, 4:40 PM2

1) Read these instructions.

2) Keep these instruction.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two blades and a

third grounding prong. The third prong are provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

15) Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such a vases,

shall be placed on the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

S3126A

PORTABLE CART WARNING

(symbol provided by RETAC)

3V00101A_En_p02-11 6/2/05, 4:40 PM3

SAFETY PRECAUTIONS

The unit emits heat when in operation. Do not place any covers or blankets on the unit, this may cause

overheating. Do not block ventilation holes, or set up near radiators. Do not place in direct sunshine. When

placing on a shelf leave 10 cm (4 inches) free space around the entire unit.

Notes when mounting the Plasma Display on a wall

•When installing the unit on a wall, allow at least 6 cm (2 1/2 inches) clearance between the rear of the Plasma

Display and the wall. Clearance of less than 6 cm (2 1/2 inches) will obstruct the vents and may cause the

interior of the unit to overheat, resulting in damage to the unit.

•If the unit is to be mounted on the wall, contact the retailer where you purchased the Plasma Display for

advice, and have the equipment professionally installed. Incomplete or improper installation may cause injury

to you and/or the Plasma Display.

•Bracket holes: To attach a wall mounting bracket (not supplied) here, remove the screws.

IMPORTANT NOTICE

Possible Adverse Effects on Plasma Screen: If a fixed (non-moving) pattern remains on the plasma screen

for long periods of time, the image can become permanently engrained in the plasma display panel and cause

subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never

leave your plasma display on for long periods of time while it is displaying the following formats or images:

•Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.

•Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on a

normal (4:3) display (gray bars at top and bottom of screen); or viewing normal style (4:3) media on a

widescreen (16:9) display (gray bars on left and right sides of screen).

To avoid the engraining, we recommend that you use the screen saver function. (see P.34)

The following symptoms are not signs of malfunction but technical limitation. Therefore we disclaim

any responsibility for these symptoms.

•Plasma display panels are manufactured using an extremely high level of precision technology,

however sometimes parts of the screen may be missing picture elements or have luminous spots.

This is not a sign of a malfunction.

•Do not install the Plasma Display near electronic equipment that is susceptible to electromagnetic waves.

Some equipment placed too near this unit may cause interference.

• Effect on infrared devices – There may be interference while using infrared devices such as infrared

cordless headphones.

10cm

Bracket holes

3V00101A_En_p02-11 6/2/05, 4:40 PM4

Troubleshooting .......................................................................... 37

Specifications .............................................................................. 38

LIMITED WARRANTY ................................................................ 39

Display operation ........................................................................ 18

Selecting the video input source ................................................. 19

Labeling the video input source .................................................. 19

Closed Caption............................................................................ 20

Setting the V-Chip ....................................................................... 21

Setting the panel lock .................................................................. 24

Setting the picture size ................................................................ 25

Setting the picture scroll .............................................................. 27

Selecting the cinema mode ......................................................... 28

Adjusting the picture preference ................................................. 29

Picture control adjustment........................................................... 30

Selecting the color temperature .................................................. 31

Resetting your picture adjustment............................................... 31

Sound control adjustment ........................................................... 32

Selecting the HDMI audio input source ....................................... 32

Selecting the BBE ....................................................................... 33

Resetting your audio adjustment................................................. 33

Screen Saver function ................................................................. 34

Picture control adjustment in the PC mode ................................. 35

Sound control adjustment in the PC mode.................................. 36

IMPORTANT SAFETY INSTRUCTIONS ...................................... 3

SAFETY PRECAUTIONS ............................................................. 4

IMPORTANT NOTICE .................................................................. 4

Contents ........................................................................................ 5

Features ........................................................................................ 6

Power source ................................................................................ 6

Parts and functions ....................................................................... 7

Remote control .............................................................................. 8

Connections to other equipment ................................................. 12

Setting the language ................................................................... 17

PREPARATIONS

OTHERS

OPERATION

Contents

3V00101A_En_p02-11 6/2/05, 4:40 PM5

Features

•Picture Adjustments Using The Remote Control - The On-Screen display allows precise remote control

adjustment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.

•Programmable Display Sleep Timer - Operable from the remote control, the Plasma Display can be

programmed up to 120 minutes to turn off automatically.

•V-Chip - The V-Chip function can read the rating of a broadcast program or movie content if the program is

encoded with this information. V-chip will allow you to set a restriction level.

•BBE - BBE gives you vivid sound with incredible presence.

•S-Video/Component Video Jacks - A VCR, DVD player, satellite receiver or other audio/video component

can be connected to this unit.

•Video Input Jacks - This unit is equipped 3 types of video input jacks. The component video in jacks and

S-video in jack enable you to watch the DVD player or the video devices with high quality picture.

•On-Screen 3 Language Display - You can select one of 3 languages, English, Spanish or French for on-

screen programming.

NOTES:

•Please make sure to insert the cord securely at both the Plasma Display and the wall outlet.

•The AC Cord has a grounding-type AC line plug. If the supplied AC cord does not match you AC outlet,

contact a qualified electrician, do not defeat the purpose of a grounding plug.

WARNING:

•DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC

CORD. THIS COULD CAUSE FIRE, ELECTRICAL SHOCK, OR DAMAGE.

• DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE DISPLAYED. THIS COULD

CAUSE FIRE, ELECTRICAL SHOCK, OR DAMAGE.

CAUTION:

•WHEN THIS UNIT IS NOT USED FOR A LONG TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF

SAFETY, BE SURE TO UNPLUG IT FROM THE AC OUTLET.

•DO NOT PLUG/UNPLUG THE PLUG WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRICAL

SHOCK.

•IF YOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED ONE IS

RECOMMENDED. CONTACT CUSTOMER SERVICE AT 1-800-289-0980.

Power source

TO USE AC POWER

1. Connect the AC cord plug into this unit's AC IN jack.

2. Connect the AC cord into an AC outlet.

AC cord (supplied)

AC 120V, 60Hz

3V00101A_En_p02-11 6/2/05, 4:40 PM6

Parts and functions

Front

Rear

Side

PHONE jack

AUDIO (L/R)

VIDEO IN jacks

S-Video IN jack

*VOLUME

▲/▼

buttons

POWER

button

*CURSOR ▲/▼ buttons

Remote sensor

INPUT button STANDBY/ON

indicator

S-VIDEO 2 IN jack

S-VIDEO 1 IN jack

AUDIO (L/R)/VIDEO OUT jacks

COMPONENT2 IN jacks

COMPONENT1 IN jacks

AUDIO (L/R)/VIDEO IN jacks (VIDEO1)

AC power cord socket

HDMI IN jack

HDMI AUDIO (L/R) IN jacks

PC IN jack

PC AUDIO (L/R) IN jacks

AUDIO (L/R)/VIDEO IN jacks (VIDEO2)

*To display the menu screen.

Press both

VOLUME

▲/▼

buttons

at the same time to display the menu screen.

CURSOR ▲/▼ buttons and

VOLUME

▲/▼

buttons can be used to select the desired setting during the menu

screen operations.

3V00101A_En_p02-11 6/2/05, 4:40 PM7

Remote control

10. VCR Operation Buttons* - Press to operate your

VCR if programmed properly using a code listed on

page 10.

11. DISPLAY Button - When you press this button, the

input source will appear on the lower right corner of

the screen. Press the button again to remove display

from the screen.

12. MUTE Button - To turn off the sound, press this

button once. The Plasma Display will be silenced and

the symbol "MUTE" will appear on the screen. The

muting feature can be released by pressing the

MUTE button again or one of the VOL (VOLUME) +

or – buttons.

13. QUICK VIEW Button - This button allows you to go

back to the previous input source selected by just

pressing the QUICK VIEW button. Press this button

again to return to the channel you were watching.

14. +10/CH ENTER Button* - Some connected equip-

ment such as a Cable/Satellite box, VCR, or DVD

may require this button to input selected channels.

15. VOL (VOLUME) + / – Buttons - Press the button

to increase, or the button to decrease the sound

level.

16. ENTER Button - Use to enter or select information

for On-Screen operations.

17. EXIT Button - Press to remove setup menu.

18. INPUT SELECT Button - Press to display SOURCE

SELECTION menu.

19. PICTURE SIZE Button - Press to display PICTURE

SIZE menu.

20. DVD Operation Buttons* - Press to operate your

DVD if programmed properly using a code listed on

page 10.

1. PLASMA DISPLAY, VCR, CABLE, DVD POWER

Button* - Used to turn the Plasma Display, VCR,

Cable/Satellite box or DVD on or off after you select

the operating mode on step 9.

2. SLEEP Button - To set the Plasma Display to turn

off after a preset amount of time, use the SLEEP

button on the remote control.

3. Direct Channel Selection Buttons (0-9)* - Allows

direct access to any channel of the VCR, Cable/

Satellite box or DVD.

4. CH (CHANNEL)/CURSOR ▲ / ▼ Buttons* - Used to

operate the menu functions of the Plasma Display,

and to change the channels of a Cable/Satellite box.

5. MENU Button - Use to display the On-Screen menu

function.

6. RESET Button - Press to reset the On-Screen

picture adjustments to their factory preset positions.

7. CLOSED CAPTION Button - Press this button to

switch between normal mode and the two Closed

Caption modes (captions and 1/2 of full screen text).

Closed Captioning will display text on screen for

hearing impaired viewers.

8. CODE SET Button - Used to register the 2-digit

codes to operate your VCR or Cable/Satellite box.

Press this button and the VCR button or the CABLE

button simultaneously to start a registration (See

page 10).

9. TV, VCR, CABLE, DVD Selector Buttons - Press to

select the Plasma Display, VCR, Cable/Satellite box

or DVD to be operated.

*You can use these buttons to operate

your VCR, Cable/Satellite box or DVD

after you have programmed the re-

mote control for the code that oper-

ates your VCR, Cable/Satellite box or

DVD (see page 10 and 11).

820

3V00101A_En_p02-11 6/2/05, 4:40 PM8

A, B, C, D

B, C, D

B, D

1. Open the battery compartment cover.

2. Install two "AAA" batteries (supplied).

HOW TO INSTALL BATTERIES

Before using the remote control, batteries must first be installed.

3. Replace the battery compartment cover.

BATTERY PRECAUTIONS

These precautions should be followed when using batteries

in this device:

• Use only the size and type of batteries specified.

•Be sure to follow the correct polarity when installing the

batteries as indicated in the battery compartment.

Reversed batteries may cause damage to the device.

•Do not mix different types of batteries together (e.g.

Alkaline and Carbon-zinc) or old batteries with fresh ones.

•If the device is not to be used for a long period of time,

remove the batteries to prevent damage or injury from

possible battery leakage.

•

Do not try to recharge batteries not intended to be recharged;

they can overheat and rupture. (Follow battery manufacturer's

directions.)

Use two "AAA" size batteries. The batteries may last approximately

one year depending on how much the remote control is used. For

best performance, it is recommended that batteries should be

replaced on a yearly basis, or when the remote operation becomes

erratic. Do not mix old and new batteries or different types.

HOW TO USE THE REMOTE CONTROL

You may be able to use the remote control to operate

your VCR and Cable/Satellite box along with the Plasma

Display after the batteries are installed and you have

registered the codes that operate your products.

Some buttons are used exclusively for each product and

some buttons are used in common with each product.

To operate your products correctly using this universal

remote control follow each step below.

A. For PLASMA DISPLAY

Press the TV button first.

B. For VCR

Press the VCR button first.

C. For CABLE/SATELLITE box

Press the CABLE button first.

Aim remote at CABLE/SATELLITE box.

NOTES:

•Some buttons that have same functions are called different

names according to the brand and model of the product. For

example, RESET may be called "CANCEL".

•The buttons A, B, C and D are used exclusively for each

product. You can use these buttons whenever you want.

Press other buttons to operate the features of your

Plasma Display. You can use the VOL + and – buttons,

the 0-9 buttons.

Press other buttons to operate the features of your VCR.

You can use the VCR CH ▲ and ▼ buttons, the 0-9

buttons, the CH ENTER button.

Aim remote at VCR.

Press the POWER button.

Aim remote at Plasma Display.

Press other buttons to operate the features of your

CABLE/SATELLITE box. You can use the CH ▲ and ▼

buttons, the 0-9 buttons, the CH ENTER button.

Press the POWER button to turn on your CABLE/SATELLITE box.

D. For DVD

Press the DVD button first.

Aim remote at DVD.

Press other buttons to operate the features of your DVD.

You can use the DVD SKIP 6 and 7 buttons, the

TOP MENU button, the DVD CLEAR button, the DVD

MENU button, the 0-9 buttons, the CH ENTER button.

Press the POWER button to turn on DVD.

Press the POWER button to turn on VCR.

Remote control

3V00101A_En_p02-11 6/2/05, 4:40 PM9

Allegro

Allegro A/B Switch

Gemini

General Electric

General Instrument

Hamlin

Jerrold

Kale Vision

Macom

Magnavox

NSC

Oak

Panasonic

Paragon

Philips

Pioneer

58, 62

05, 31, 38

05, 06

02, 03, 45, 65, 66

04, 07, 08, 09, 10, 18, 60, 63

14, 21

35, 39, 68, 69, 70

11, 32, 42

13, 20

47, 50, 52, 54, 55

15, 43

CABLE/SATELLITE

RCA DSS

Regency

Samsung

Sprucer

Scientic Atlanta

Standard Comp

Texscan

Tocom

Unika

United Satellite

Universal

Vid Tech

Video Way

Viewstar

Zenith

Zenith Satellite

16, 23, 36, 64

39, 56, 71

17, 18, 46

48, 62

58, 62

54, 55, 72

01, 53, 74

12, 28, 30, 51

Akai 23, 38, 41

VCR

Panasonic

Admiral 08, 61 Multi Tech 39

Adventura 31 NEC 02, 18

Aiwa 31 Orion 33, 50

14, 51, 59

Audio Dynamics 02, 18 Pentax 15

Bell & Howell 06, 47 Philco 07, 14

Broksonic 21, 26, 33, 50, 55 Philips 07, 14, 27

Canon 14 Pioneer 10, 15

Citizen 09 Portland 46

Craig 12 Pro Scan 16, 60

Curtis Mathes 14, 59 Quasar 14, 59

Daewoo 44, 46, 48, 54 RCA 15, 16, 20, 27, 40, 42, 60

Daytron 36, 46 Realistic 06, 08, 12, 14, 31

DBX 02, 18 Samsung 20, 30

Emerson 03, 21 23, 26, 33, 35, 43, 50 Sansui 39

Fisher 11, 12, 13, 47 Sanyo 06, 12, 47

Funai 31 Scott 04, 05, 33, 43

General Electric 14, 16, 20 Sears 06, 09, 11, 12, 15

Goldstar 09 Sharp 08, 61

Go Video 56, 62, 63 Shintom 39

Hitachi 15, 57 Signature 2000 08, 14, 16, 19, 31, 49

Instant Replay 14, 27 Sony 17, 32, 37

J.C. Penney 14, 15, 18, 27 Sylvania 07, 14, 27

JVC 02, 25, 58 Symphonic 31

Kenwood 02 Tashiko 09

Logik 39 Tatung 02

LXI 09, 31 Teac 02, 31

Magnavox 07, 14, 31 Teknika 34

Marantz 07, 18 Toshiba 05, 15

Marta 09 XR1000 39

Memorex 06, 12, 14, 31, 33 Vector Research 04, 18

Mitsubishi 04, 22, 52, 64 Yamaha 02, 18

Montgomery Ward

08, 14, 16, 19, 31, 49

Zenith

01, 24, 25, 29, 37

REGISTRATION CODES BY PRODUCT AND BRAND NAME

Press CODE SET and VCR, CABLE or DVD you want to register at the same time.

Enter the 2-digit code listed below using the Direct Channel Selection buttons (0-9) within 10 seconds.

TO REGISTER YOUR VCR, CABLE/SATELLITE BOX OR DVD WITH THE REMOTE CONTROL

NOTES: •When shipped from the factory, the remote control is set to operate your Plasma Display .

•If you do not enter the code within 10 seconds from step 1 or enter the non-listed code below, this operation

is canceled.

• When you install or replace batteries, you may need to register the codes again for the products you want to

control.

Remote control

3V00101A_En_p02-11 6/2/05, 4:40 PM10

Remote control

Ferguson 01

DVD

Sampo

Aiwa 23 Raite 13

Apex 20 RCA 01, 06

Denon 00, 17 Saba 01

Funai 18, 32 Samsung 10

Hitachi 11 Sharp 08

JVC 09 Silvania 18, 32

Kenwood 15, 29 SMC 25

Konka 19 Sony 04, 26, 27, 28

Mitsubishi 05 Technics 00

Nordmende 01 Thomson 01

Onkyo 21 Toshiba 03

Orion 33 Vialta 31

Oritron 24 Wave 22

Panasonic 00 Yamaha 00, 30

Philips 03, 16 Zenith 07, 12

Pioneer 02

3V00101A_En_p02-11 6/2/05, 4:40 PM11

Connections to other equipment

The exact arrangement you use to interconnect various video and audio components to the Plasma Display is

dependent on the model and features of each component. Check the Owner's Manual provided with each

component for the location of video and audio inputs and outputs.

The connection diagrams below are offered as suggestions. You may need to modify them to accommodate

your particular assortment of components. The diagrams are intended to show component video and audio

interconnections only.

To connect the Plasma Display to a VCR with an S-Video cord

If you connect a VCR with a S-VIDEO cord to the S-VIDEO IN jack on the rear of the

Plasma Display

, you must

also connect

the audio cords to the AUDIO IN jacks on the rear of the Plasma Display. The S-VIDEO cord only

carries the video signal. The audio signal is separate.

NOTE:

When the S-video cord and the video cord are connected to each jack at the same time, the S-video cord takes

precedence over the video cord.

To S-Video OUT

To Audio OUT

Audio cord (not supplied)

S-Video cord (not supplied)

To S-VIDEO IN 1 (or 2)

To connect the Plasma Display to a VCR

Rear lower of the Plasma Display

To Audio/Video OUT

Audio/Video cord (not supplied)

To AUDIO/VIDEO IN 1 (or 2)

To AUDIO

IN 1 (or 2)

Rear lower of the Plasma Display

3V00101A_En_p12-16 6/2/05, 4:40 PM12

Rear lower of the Plasma Display

To connect the Plasma Display to a DVD player/Satellite receiver

If your DVD player or Satellite receiver has a S-Video out jack, connect cords as shown.

Rear lower of the Plasma Display

To S-Video OUT

Audio cord (not supplied)

To Audio OUT

S-Video cord (not supplied)

To S-VIDEO IN 1 (or 2)

To connect the Plasma Display to a DVD player with component video

If your DVD player has component video out jacks, connect your Plasma Display to a DVD player using a

component video cord. It can greatly enhance picture quality and performance.

To Component OUT

To Audio OUT

Audio cord (not supplied)

Video cord (not supplied)

To AUDIO

IN 1 (or 2)

To COMPONENT IN 1 (or 2)

NOTE:

Component Video input of this unit are for use of device which output 480i/1080i interlaced signals and 480p/

720p progressive signals.

Connections to other equipment

3V00101A_En_p12-16 6/2/05, 4:40 PM13

Using an Audio Amplifier

To connect the Plasma Display to an Audio Amplifier, connect the unit to the amplifier using an Audio Cable (not

supplied).

To Audio (L) Input To Audio (R) Input

Audio cord (not supplied)

Amplifier

Rear lower of the Plasma Display

AUDIO (R) OUTPUT

AUDIO (L) OUTPUT

Connections to other equipment

To connect the Plasma Display to a DTV receiver/set-top box

If you connect a DTV receiver/set-top box, connect your Plasma Display to a DTV receiver/set-top box using a

component video cord.

Rear lower of the Plasma Display

To Component OUT

To Audio OUT

Video cord (not supplied)

Audio cord (not supplied)

To COMPONENT IN 1 (or 2)

3V00101A_En_p12-16 6/2/05, 4:40 PM14

Connections to other equipment

Audio cord (not supplied)

VGA cable (not supplied)

To connect the Plasma Display to a PC (Personal Computer)

Before you connect this Plasma Display to your PC, change the adjustment of your PC’s Resolution and

Refresh rate (60 Hz).

Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the

VGA connector PC MONITOR on the back of the

Plasma Display

. Attach the connectors firmly with the screws

on the plug.

In case of a Multimedia computer, connect the audio cables to the audio outputs of your

Multimedia computer and to the AUDIO L and R connectors of the PC AUDIO (L/R) IN jacks of the Plasma

Display.

Press INPUT SELECT on the remote control to select PC mode.

Switch on the computer. The Plasma Display can operate as the computer monitor.

Monitor Display modes

MODE Resolution Refresh rate

VGA 640x480 60Hz

SVGA 800x600 56.3Hz

SVGA 800x600 60.3Hz

XGA 1024x768 60Hz

To return to normal mode

Press INPUT SELECT again.

Rear lower of the Plasma Display

To connect the Plasma Display to a HDMI or a DVI device

Rear lower of the Plasma Display

HDMI - to - DVI adapter cable

(HDMI type A connector)

(not supplied)

Audio cord (not supplied)

HDMI cable (type A connector)

(not supplied)

To DVI output

To HDMI out

The HDMI input receives digital audio and uncompressed video from a HDMI device or uncompressed digital

video from a DVI device.

When you connect to a DVI device with a HDMI-to-DVI adapter cable, it transfers only the video signal. Separate

analog audio cords are required.

NOTE:

You must choose an appropriate setting for each connection (see page 32. “Selecting the HDMI audio input

source”).

To PC AUDIO

IN jacks

To PC IN

3V00101A_En_p12-16 6/2/05, 4:40 PM15

To connect the Plasma Display to a camcorder

To connect the Plasma Display to a Game

The Plasma Display can also be used as a display device for many video games. However, due to the wide

variety of signals generated by these devices and subsequent hook-up variations required, they have not all

been included in the suggested connection diagrams. You'll need to consult each component's Owner's Manual

for additional information.

To playback from a camcorder, connect the camcorder to the Plasma Display as shown.

Side of the Plasma Display

Audio/Video cord (not supplied)

To Audio/Video OUT

Side of the Plasma Display

To Audio/Video OUT

Audio/Video cord (not supplied)

Connections to other equipment

3V00101A_En_p12-16 6/2/05, 4:40 PM16

Press or to select

SETUP menu.

Press or to select the desired language: English (ENGLISH),

French (FRANÇAIS) or Spanish (ESPAÑOL).

Press ▲ or ▼ to select

“LANGUAGE”.

Press EXIT to return to the normal screen.

Press MENU. The menu screen will appear.

Setting the language

You can choose from three different

languages (English, French and

Spanish) for the on-screen displays.

NOTE:

If no buttons are pressed for more than

about 60 seconds, the MENU screen

will return to normal operation automati-

cally.

3V00101A_En_p17-23 6/2/05, 4:40 PM17

SLEEP

To set the unit to turn off after a preset

amount of time, press SLEEP on the

remote control. The clock will count up 10

minutes for each press of the SLEEP

button (0h00m, 0h10m, ...1h50m, 2h00m).

After the sleep time is programmed, the

display will appear briefly every ten

minutes to remind you that the sleep timer is operating. To confirm

the sleep timer setting, press SLEEP and the remaining time will be

displayed for a few seconds. To cancel the sleep timer, press SLEEP

repeatedly until the display turns to 0h00m.

VOLUME

Adjust the volume level by pressing

VOL + or – . The volume level will be

indicated on the screen by white bars.

As the volume level increases, so do

the number of bars. If the volume

decreases, the number of white bars

also decreases.

QUICK VIEW

This button allows you to go back to the

last input source selected by pressing

QUICK VIEW. Press QUICK VIEW

again to return to the last input source

you were watching.

MUTE

Press MUTE to switch off the sound.

The unit’s sound will be silenced and

“MUTE” will appear on the screen. The

sound can be switched back on by pressing

this button again or VOL + or –.

Display operation

DISPLAY

Press DISPLAY to display the current information on the screen.

•VIDEO mode selected

•Video label (if preset)

•Content rating

•Sleep time (if preset)

•Picture size

Press DISPLAY again to clear the call display.

VOLUME 32

VIDE01

MUTE

SLEEP

2h00m

3V00101A_En_p17-23 6/2/05, 4:40 PM18

Selecting the video input source/Labeling the video input source

Press MENU. Then press

or to select OPTION

menu.

Press ▲ or ▼ to select

“VIDEO LABEL”.

Press or . The VIDEO

LABEL menu will appear.

Press ▲ or ▼ to select the

video source you want to

label.

Press

to select the

desired

label for that input

source.

– :Uses the default

label name

VCR :Video cassette

recorder

DVD :DVD video

DTV :

Digital TV set-top box

SAT :Satellite box

CBL :Cable box

HD :HDMI device (only HDMI)

Press EXIT to return to the normal screen.

Selecting the video input source

ress INPUT SELECT to view

a signal from another device

connected to your Plasma

Display, such as a VCR or DVD

player. You can select VIDEO1,

VIDEO2, VIDEO3 (left side of

the unit), COMPONENT1,

COMPONENT2, HDMI, or PC

depending on which input jacks

you used to connect your

devices.

Pressing INPUT SELECT on the remote control displays the current

signal source. To change the video input source, press INPUT

SELECT again or 0-6.

Labeling the video input source

The video label feature allows you to label each input source for

your unit.

3V00101A_En_p17-23 6/2/05, 4:40 PM19

NOTES:

• If the program or video you selected is not closed-captioned, no captions will display on-screen.

•If text is not available in your viewing area, a black rectangle may appear on-screen. If this happens, set the

Closed Caption feature to “OFF”.

• When selecting Closed Captions, the captioning will be delayed approx. 10 seconds.

•If no caption signal is received, no captions will appear, but the plasma Display will remain in the Caption Mode.

•Misspellings or unusual characters may occasionally appear during Closed Captioning. This is normal with

Closed Captioning, especially with live programs. This is because during live programs, captions are also

entered live. These transmissions do not allow time for editing.

•When Captions are being displayed, on-screen displays, such as volume and mute may be seen but may

interfere with Closed Captions.

•Some Cable TV systems and copy protection systems may interfere with the Closed Captioned signal.

Closed Caption

WHAT IS CLOSED CAPTIONING?

This Plasma Display has the capability to decode and display Closed Captioned television programs. Closed

Captioning will display text on the screen for hearing impaired viewers and may translate and display text in

another language if broadcast.

Select desired video source for the Plasma Display.

Press MENU, then press or to display the SETUP menu.

4Press or to select the desired Closed Caption mode.

3Press ▲ or ▼ to select “CLOSED CAPTION”.

NOTE:

This screen can be displayed by pressing the CLOSED

CAPTION button on the Remote control.

NOTE:

To turn the Closed Caption feature off, select “OFF”.

Captions: This Closed Caption Mode will display text on the screen

in English or another language if broadcast. Generally, Closed

Captions in English are transmitted on C1 and Closed Captions in

other languages are transmitted on C2.

Text: The Text Closed Caption Mode will usually fill 1/2 of the screen

with a programming schedule or other information.

5Press EXIT to return to the normal screen.

3V00101A_En_p17-23 6/2/05, 4:40 PM20

Page is loading ...

Sansui HDPDP4200 Owner's manual

Brand: Sansui

Model: HDPDP4200

Category: Plasma TVs

Type: Owner's manual

This manual is also suitable for

HDPDP4200A

Download PDF

report

Sansui HDPDP4200 Owner's manual

This manual is also suitable for

Sansui HDPDP4200 Owner's manual

Other documents