Hitachi Koki USA H30PV User manual

Brand: Hitachi Koki USA

Model: H30PV

Category: Power tools

Type: User manual

This manual is also suitable for

H 30PV

H 30PV

Hammer

Piqueur

Martello

Hakhamer

Martillo

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich, F. R. Germany

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo prodotto è

conforme agli standard o ai documenti standardizzati EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 e/o

EN61000-3-11 conforme alle direttive 73/23/CEE, 89/336/CEE, 98/

37/CE e/o 2000/14/CE del concilio.

2000/14/CE

• Procedimento di valutazione conformità: ALLEGATO VI

• Ente notificato: BSI Product Services, Maylands Avenue Hemel

Hempstead Herts HP2 4SQ UK

• Livello di potenza sonora misurato: 97,65 dB

• Livello di potenza sonora garantito: 99 dB

Questa dichiarazione è applicabile ai prodotti cui sono applicati

i marchi CE.

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit produkt

conform de richtlijnen of gestandardiseerde documenten

EN50144, HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-

3-3 en/of EN61000-3-11 voldoet aan de eisen van EEG Bepalingen

73/23/EEG, 89/336/EEG, 98/37/EC en/of 2000/14/EC.

2000/14/EC

• Conformiteit vaststellingsprocedure: ANNEX VI

• In kennis gesteld instituut: BSI Product Services, Maylands

Avenue, Hemel Hempstead, Herts. HP2 4SQ UK

• Gemeten geluidsdruk: 97,65 dB

• Gegarandeerde geluidsdruk: 99 dB

Deze verklaring is van toepassing op produkten voorzien van de

CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que este

producto está de acuerdo con las normas o con los documentos

de normalización EN50144, HD400, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3 y/o EN61000-3-11, según indican las

Directrices del Consejo 73/23/CEE, 89/336/CEE, 98/37/CE y/o 2000/

14/CE.

2000/14/CE

• Procedimiento de evaluación de conformidad: ANEXO VI

• Entidad notificada: BSI Product Services, Maylands Avenue

Hemel Hempstead Herts HP2 4SQ Reino Unido

• Nivel de potencia acústica medida: 97,65 dB

• Nivel de potencia acústica garantizada: 99 dB

Esta declaración se aplica a los productos con marcas de la CE.

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in

conformity with standards or standardized documents EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 and/

or EN61000-3-11 in accordance with Council Directives 73/23/

EEC, 89/336/EEC, 98/37/EC and/or 2000/14/EC.

2000/14/EC

• Conformity assessment procedure: ANNEX VI

• Notified body: BSI Product Services, Maylands Avenue Hemel

Hempstead Herts HP2 4SQ UK

• Measured sound power lever: 97.65 dB

• Guaranteed sound power level: 99 dB

This declaration is applicable to the product affixed CE marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses Produkt

den Standards oder standardisierten Dokumenten EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 und/

oder EN61000-3-11 in Übereinstimmung mit den Direktiven des

Europarats 73/23/EWG, 89/336/EWG, 98/37/CE und/order 2000/

14/CE entspricht.

2000/14/CE

• Übereinstimmungsbeurteilungsverfahren: ANNEX VI

• Informierte Körperschaft: BSI Product Services, Maylands

Avenue Hemel Hempstead Herts HP2 4SQ UK

• Gemessener Schallleistungspegel: 97,65 dB

• Garantierter Schallleistungspegel: 99 dB

Diese Erklärung gilt für Produkte, die die CE-Markierung tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière respon-sabilité que

ce produit est conforme aux normes ou documents normalisés

EN50144, HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-

3-3 et/ou EN61000-3-11 en accord avec les Directives 73/23/CEE,

89/336/CEE, 98/37/CE et/ou 2000/14/CE du Conseil.

2000/14/CE

• Procédure d’évaluation de conformité : ANNEXE VI

• Organisme notifié : BSI Product Services, Maylands Avenue

Hemel Hempstead Herts HP2 4SQ R-U

• Niveau de puissance sonore mesuré : 97,65 dB

• Niveau de puissance sonore garanti : 99 dB

Cette déclaration s’applique aux produits désignés CE.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Instruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste instruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer cuidadosamente y comprender estas instrucciones antes del uso.

207

Code No. C99104673 N

Printed in Japan

28. 11. 2001

Y. Hirano (EMO)

H 30PV

Hammer

Piqueur

Martello

Hakhamer

Martillo

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich, F. R. Germany

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo prodotto è

conforme agli standard o ai documenti standardizzati EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 e/o

EN61000-3-11 conforme alle direttive 73/23/CEE, 89/336/CEE, 98/

37/CE e/o 2000/14/CE del concilio.

2000/14/CE

• Procedimento di valutazione conformità: ALLEGATO VI

• Ente notificato: BSI Product Services, Maylands Avenue Hemel

Hempstead Herts HP2 4SQ UK

• Livello di potenza sonora misurato: 97,65 dB

• Livello di potenza sonora garantito: 99 dB

Questa dichiarazione è applicabile ai prodotti cui sono applicati

i marchi CE.

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit produkt

conform de richtlijnen of gestandardiseerde documenten

EN50144, HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-

3-3 en/of EN61000-3-11 voldoet aan de eisen van EEG Bepalingen

73/23/EEG, 89/336/EEG, 98/37/EC en/of 2000/14/EC.

2000/14/EC

• Conformiteit vaststellingsprocedure: ANNEX VI

• In kennis gesteld instituut: BSI Product Services, Maylands

Avenue, Hemel Hempstead, Herts. HP2 4SQ UK

• Gemeten geluidsdruk: 97,65 dB

• Gegarandeerde geluidsdruk: 99 dB

Deze verklaring is van toepassing op produkten voorzien van de

CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que este

producto está de acuerdo con las normas o con los documentos

de normalización EN50144, HD400, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3 y/o EN61000-3-11, según indican las

Directrices del Consejo 73/23/CEE, 89/336/CEE, 98/37/CE y/o 2000/

14/CE.

2000/14/CE

• Procedimiento de evaluación de conformidad: ANEXO VI

• Entidad notificada: BSI Product Services, Maylands Avenue

Hemel Hempstead Herts HP2 4SQ Reino Unido

• Nivel de potencia acústica medida: 97,65 dB

• Nivel de potencia acústica garantizada: 99 dB

Esta declaración se aplica a los productos con marcas de la CE.

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in

conformity with standards or standardized documents EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 and/

or EN61000-3-11 in accordance with Council Directives 73/23/

EEC, 89/336/EEC, 98/37/EC and/or 2000/14/EC.

2000/14/EC

• Conformity assessment procedure: ANNEX VI

• Notified body: BSI Product Services, Maylands Avenue Hemel

Hempstead Herts HP2 4SQ UK

• Measured sound power lever: 97.65 dB

• Guaranteed sound power level: 99 dB

This declaration is applicable to the product affixed CE marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses Produkt

den Standards oder standardisierten Dokumenten EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 und/

oder EN61000-3-11 in Übereinstimmung mit den Direktiven des

Europarats 73/23/EWG, 89/336/EWG, 98/37/CE und/order 2000/

14/CE entspricht.

2000/14/CE

• Übereinstimmungsbeurteilungsverfahren: ANNEX VI

• Informierte Körperschaft: BSI Product Services, Maylands

Avenue Hemel Hempstead Herts HP2 4SQ UK

• Gemessener Schallleistungspegel: 97,65 dB

• Garantierter Schallleistungspegel: 99 dB

Diese Erklärung gilt für Produkte, die die CE-Markierung tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière respon-sabilité que

ce produit est conforme aux normes ou documents normalisés

EN50144, HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-

3-3 et/ou EN61000-3-11 en accord avec les Directives 73/23/CEE,

89/336/CEE, 98/37/CE et/ou 2000/14/CE du Conseil.

2000/14/CE

• Procédure d’évaluation de conformité : ANNEXE VI

• Organisme notifié : BSI Product Services, Maylands Avenue

Hemel Hempstead Herts HP2 4SQ R-U

• Niveau de puissance sonore mesuré : 97,65 dB

• Niveau de puissance sonore garanti : 99 dB

Cette déclaration s’applique aux produits désignés CE.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Instruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste instruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer cuidadosamente y comprender estas instrucciones antes del uso.

207

Code No. C99104673 N

Printed in Japan

28. 11. 2001

Y. Hirano (EMO)

1 2

3 4

5 6

7 8

9 10

English Deutsch Français

Tool shank Werkzeugschaft Queue d’outil

Front cap Frontkappe Capuchon avant

Grip (A) Griff (A) Poignée (A)

Grip (B) Griff (B) Poignée (B)

Crank cover Kurbeldeckel Couvercle de manivelle

Wear limit Verschleißgrenze Limite d’usure

No. of carbon brush Nr. der kohlebürste No. de balai en carbone

Usual carbon brush Gewöhnliche Kohlebürste Balai en carbone ordinaire

Auto-stop carbon brush Auto-Stop Kohlebürest

Balai en carbone à arrêt

automatique

Italiano Nederlands Español

Gambo dell’utensile Boorschacht Barrena

Tappo anteriore Voorkap Tapa frontal

Impugnatura (A) Greep (A) Empuñadura (A)

Impugnatura (B) Greep (B) Empuñadura (B)

Coperchio dell’incastellatura Bedekking Cubierta del motor

Limite d’usura Slijtage-limiet Límite de desgaste

Numero delle spazzole di carbone Nr. van koolborstel No. de contacto de carbón

Spazzola di carbonecomune Normale koolborstel Escobilla de carbón usual

Spazzola di carbone ad

Auto-stop koolborstel

Escobilla de carbón de parada

arresto automatico automática

1 2

17 mm

▼

7 a

8 43 6 mm

9 73 7 mm

1 2

3 4

5 6

7 8

9 10

English Deutsch Français

Tool shank Werkzeugschaft Queue d’outil

Front cap Frontkappe Capuchon avant

Grip (A) Griff (A) Poignée (A)

Grip (B) Griff (B) Poignée (B)

Crank cover Kurbeldeckel Couvercle de manivelle

Wear limit Verschleißgrenze Limite d’usure

No. of carbon brush Nr. der kohlebürste No. de balai en carbone

Usual carbon brush Gewöhnliche Kohlebürste Balai en carbone ordinaire

Auto-stop carbon brush Auto-Stop Kohlebürest

Balai en carbone à arrêt

automatique

Italiano Nederlands Español

Gambo dell’utensile Boorschacht Barrena

Tappo anteriore Voorkap Tapa frontal

Impugnatura (A) Greep (A) Empuñadura (A)

Impugnatura (B) Greep (B) Empuñadura (B)

Coperchio dell’incastellatura Bedekking Cubierta del motor

Limite d’usura Slijtage-limiet Límite de desgaste

Numero delle spazzole di carbone Nr. van koolborstel No. de contacto de carbón

Spazzola di carbonecomune Normale koolborstel Escobilla de carbón usual

Spazzola di carbone ad

Auto-stop koolborstel

Escobilla de carbón de parada

arresto automatico automática

1 2

17 mm

▼

7 a

8 43 6 mm

9 73 7 mm

English

GENERAL OPERATIONAL PRECAUTIONS

WARNING! When using electric tools, basic safety

precautions should always be followed to reduce the

risk of fire, electric shock and personal injury, including

the following.

Read all these instructions before operating this product

and save these instructions.

For safe operations:

1. Keep work area clean. Cluttered areas and benches

invite injuries.

2. Consider work area environment. Do not expose

power tools to rain. Do not use power tools in

damp or wet locations. Keep work area well lit.

Do not use power tools where there is risk to

cause fire or explosion.

3. Guard against electric shock. Avoid body contact

with earthed or grounded surfaces. (e.g. pipes,

radiators, ranges, refrigerators).

4. Keep children away. Do not let visitors touch the

tool or extension cord. All visitors should be kept

away from work area.

5. Store idle tools. When not in use, tools should

be stored in a dry, high or locked up place, out

of reach of children.

6. Do not force the tool. It will do the job better and

safer at the rate for which it was intended.

7. Use the right tool. Do not force small tools or

attachments to do the job of a heavy duty tool.

Do not use tools for purposes not intended; for

example, do not use circular saw to cut tree limbs

or logs.

8. Dress properly. Do not wear loose clothing or

jewelry, they can be caught in moving parts.

Rubber gloves and non-skid footwears are

recommended when working outdoors. Wear

protecting hair covering to contain long hair.

9. Use eye protection. Also use face or dust mask

if the cutting operation is dusty.

10. Connect dust extraction equipment.

If devices are provided for the connection of dust

extraction and collection facilities ensure these are

connected and properly used.

11. Do not abuse the cord. Never carry the tool by

the cord or yank it to disconnect it from the

receptacle. Keep the cord away from heat, oil and

sharp edges.

12. Secure work. Use clamps or a vise to hold the

work. It is safer than using your hand and it frees

both hands to operate tool.

13. Do not overreach. Keep proper footing and balance

at all times.

14. Maintain tools with care. Keep cutting tools sharp

and clean for better and safer performance. Follow

instructions for lubrication and changing

accessories. Inspect tool cords periodically and if

damaged, have it repaired by an authorized service

center. Inspect extension cords periodically and

replace, if damaged. Keep handles dry, clean, and

free from oil and grease.

15. Disconnect tools. When not in use, before servicing,

and when changing accessories such as blades,

bits and cutters.

16. Remove adjusting keys and wrenches. Form the

habit of checking to see that keys and adjusting

wrenches are removed from the tool before turning

it on.

17. Avoid unintentional starting. Do not carry a

plugged-in tool with a finger on the switch. Ensure

switch is off when plugging in.

18. Use outdoor extension leads. When tool is used

outdoors, use only extension cords intended for

outdoor use.

19. Stay alert. Watch what you are doing. Use common

sense. Do not operate tool when you are tired.

20. Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should

be carefully checked to determine that it will

operate properly and perform its intended function.

Check for alignment of moving parts, free running

of moving parts, breakage of parts, mounting and

any other conditions that may affect its operation.

A guard or other part that is damaged should be

properly repaired or replaced by an authorized

service center unless otherwise indicated in this

handling instructions. Have defective switches

replaced by an authorized service center. Do not

use the tool if the switch does not turn it on and

off.

21. Warning

The use of any accessory or attachment, other

than those recommended in this handling

instructions, may present a risk of personal injury.

22. Have your tool repaired by a qualified person.

This electric tool is in accordance with the relevant

safety requirements. Repairs should only be carried

out by qualified persons using original spare parts.

Otherwise this may result in considerable danger

to the user.

PRECAUTIONS ON USING HAMMER

1. Wear earplugs to protect your ears during

operation.

2. Do not touch the tool during or immediately after

operation. The tool becomes very hot during

operation and could cause serious burns.

3. Before starting to break, chip or drill into a wall,

floor or ceiling, thoroughly confirm that such items

as electric cables or conduits are not buried inside.

4. Wear a mask when turning your head upward.

5. Properly set the bit holder.

6. At the start of work, confirm screw tihghtening.

7. When working at a highly elevated location, pay

attention to articles and persons below.

8. Wear portective shoes to protect your feet.

9. Make positively certain that you wear gloves when

engaged in work for a long time since the grip

can become very hot.

10. There is also a risk for a tool to be damaged, and

therefore exercise utmost caution for any possible

fall of the tool when you work at an elevated

place.

English

STANDARD ACCESSORIES

(1) Case ........................................................................... 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES (sold separately)

䡬 Demolishing

Bull point (Round type)

(SDS-plus shank)

Bull point (Square type)

(SDS-plus shank)

䡬 Groove digging and edging

Cold chisel (SDS-plus shank)

Cutter (SDS-plus shank)

䡬 Grooving

Grooving chisel (SDS-plus shank)

䡬 Hammer Grease A

500g (in a can)

70g (in a tube)

30g (in a tube)

Optional accessories are subject to change without

notice.

APPLICATIONS

Demolishing concrete, chiseling concrete, grooving, bar

cutting, and driving piles.

Application examples:

Installation of piping and wiring, sanitary facility

installation, machinery installation, water supply and

drainage work, interior jobs, harbor facilities and other

civil engineering work.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Installing Tools

CAUTION

To prevent accidents, make sure to turn the switch

off and disconnect the plug from the receptacle.

NOTE:

When using tools such as bull points, cutters, etc.,

make sure to use the genuine parts designated by

our company.

(1) Clean the shank portion of the tool.

(2) Insert the tool in a twisting manner into the tool

holder until it latches itself. (Fig. 1, 2)

(3) Check the latching by pulling on the tool. (Fig. 3)

5. Deciding Working Position of Tool

The tool can be turned every 30 degrees and can

be fixed at the position of 12 steps.

(1) As shown in Fig. 4, grip (B) is turned 60 degrees

in the direction of A, the blade angle can be changed

freely to any desired position. (Fig. 5)

(2) As shown in Fig. 6, return grip (B) in the direction

of A, and make sure that it is locked completely.

6. Removing Tool

As shown in Fig. 7, pull front cap in the direction

of A, and pull out the tool. (Fig. 8)

SPECIFICATIONS

Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)

Power Input 720W*

Full-load Impact Rate 0–3800/min.

Weight (without cord, side handle) 4.2 kg

* Be sure to check the nameplate on product as it is subject to change by areas.

English

HOW TO USE THE HAMMER (Fig. 9)

1. After placing the tip of the tool on concrete surface,

switch ON.

The switch can be turned ON if the trigger is pulled

and OFF when it is released.

Impact rate of the tool can be controlled steplessly

by varying the amount that the trigger switch is

pulled.

2. By utilizing the empty weight of the machine and

by firmly holding the hammer by both hands, you

can effectively control the subsequent recoil motion.

Proceed at a moderate work-rate, the use of too

much pushing force will impair efficiency.

GREASE REPLACEMENT

This machine is of fully oil sealed construction to

protect against dust incursion and to prevent lubricant

leakage. This machine can be used without grease

replenishment for an extended period of time. However,

perform the grease replacement to extend the service

life. Replace the grease as described below.

1. Grease Replacement Period

You should look at the grease when you change

the carbon brush. (See item 4 in the section

MAINTENANCE AND INSPECTION.)

Ask for grease replacement at the nearest authorized

Hitachi Service Center.

In the case that you are forced to change the grease

by yourself, please follow the following points.

2. How to replace grease

CAUTION:

Before replacing the grease, turn the power off and

pull out the plug from the receptacle.

(1) Disassemble the crank cover and thoroughly wipe

off the old grease inside. (Fig. 10)

(2) Supply 30g (the standard volume to cover the

connecting rod) of Hitachi Electric Hammer Grease

A in the crank case.

(3) After replacing the grease, reassemble the crank

cover securely. At this time, do not damage or lose

the oil seal.

NOTE:

The Hitachi Electric Hammer Grease A is of the low

viscosity type. When the grease is consumed,

purchase from the authorized Hitachi Service

Center.

MAINTENANCE AND INSPECTION

CAUTION

To prevent accidents, make sure to turn the switch off

and disconnect the plug from the receptacle.

1. Inspecting the tool

Since use of a dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or

replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws:

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

4. Inspecting the carbon brushes (Fig. 11)

The Motor employs carbon brushes which are

consumable parts. When they become worn to or

near the “wear limit”, it could result in motor trouble.

When an auto-stop carbon brush is equipped, the

motor will stop automatically. At that time, replace

both carbon brushes with new ones which have the

same carbon brush Number shown in the figure.

In addition, always keep carbon brushes clean and

ensure that they slide freely within the brush holders.

5. Replacing carbon brushes:

Loosen the set screw and remove the tail cover.

Remove the brush caps and carbon brushes. After

replacing the carbon brushes, do not forget to tighten

the brush caps properly and install the tail cover.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this

tool may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the

terminal marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the each terminal.

English

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning and vibration

The measured values were determined according to

EN50144.

The typical weighted root mean square acceleration

value: 8.6 m/s

Page is loading ...

1 2

3 4

5 6

7 8

9 10

English Deutsch Français

Tool shank Werkzeugschaft Queue d’outil

Front cap Frontkappe Capuchon avant

Grip (A) Griff (A) Poignée (A)

Grip (B) Griff (B) Poignée (B)

Crank cover Kurbeldeckel Couvercle de manivelle

Wear limit Verschleißgrenze Limite d’usure

No. of carbon brush Nr. der kohlebürste No. de balai en carbone

Usual carbon brush Gewöhnliche Kohlebürste Balai en carbone ordinaire

Auto-stop carbon brush Auto-Stop Kohlebürest

Balai en carbone à arrêt

automatique

Italiano Nederlands Español

Gambo dell’utensile Boorschacht Barrena

Tappo anteriore Voorkap Tapa frontal

Impugnatura (A) Greep (A) Empuñadura (A)

Impugnatura (B) Greep (B) Empuñadura (B)

Coperchio dell’incastellatura Bedekking Cubierta del motor

Limite d’usura Slijtage-limiet Límite de desgaste

Numero delle spazzole di carbone Nr. van koolborstel No. de contacto de carbón

Spazzola di carbonecomune Normale koolborstel Escobilla de carbón usual

Spazzola di carbone ad

Auto-stop koolborstel

Escobilla de carbón de parada

arresto automatico automática

1 2

17 mm

▼

7 a

8 43 6 mm

9 73 7 mm

H 30PV

Hammer

Piqueur

Martello

Hakhamer

Martillo

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich, F. R. Germany

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo prodotto è

conforme agli standard o ai documenti standardizzati EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 e/o

EN61000-3-11 conforme alle direttive 73/23/CEE, 89/336/CEE, 98/

37/CE e/o 2000/14/CE del concilio.

2000/14/CE

• Procedimento di valutazione conformità: ALLEGATO VI

• Ente notificato: BSI Product Services, Maylands Avenue Hemel

Hempstead Herts HP2 4SQ UK

• Livello di potenza sonora misurato: 97,65 dB

• Livello di potenza sonora garantito: 99 dB

Questa dichiarazione è applicabile ai prodotti cui sono applicati

i marchi CE.

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit produkt

conform de richtlijnen of gestandardiseerde documenten

EN50144, HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-

3-3 en/of EN61000-3-11 voldoet aan de eisen van EEG Bepalingen

73/23/EEG, 89/336/EEG, 98/37/EC en/of 2000/14/EC.

2000/14/EC

• Conformiteit vaststellingsprocedure: ANNEX VI

• In kennis gesteld instituut: BSI Product Services, Maylands

Avenue, Hemel Hempstead, Herts. HP2 4SQ UK

• Gemeten geluidsdruk: 97,65 dB

• Gegarandeerde geluidsdruk: 99 dB

Deze verklaring is van toepassing op produkten voorzien van de

CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que este

producto está de acuerdo con las normas o con los documentos

de normalización EN50144, HD400, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3 y/o EN61000-3-11, según indican las

Directrices del Consejo 73/23/CEE, 89/336/CEE, 98/37/CE y/o 2000/

14/CE.

2000/14/CE

• Procedimiento de evaluación de conformidad: ANEXO VI

• Entidad notificada: BSI Product Services, Maylands Avenue

Hemel Hempstead Herts HP2 4SQ Reino Unido

• Nivel de potencia acústica medida: 97,65 dB

• Nivel de potencia acústica garantizada: 99 dB

Esta declaración se aplica a los productos con marcas de la CE.

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in

conformity with standards or standardized documents EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 and/

or EN61000-3-11 in accordance with Council Directives 73/23/

EEC, 89/336/EEC, 98/37/EC and/or 2000/14/EC.

2000/14/EC

• Conformity assessment procedure: ANNEX VI

• Notified body: BSI Product Services, Maylands Avenue Hemel

Hempstead Herts HP2 4SQ UK

• Measured sound power lever: 97.65 dB

• Guaranteed sound power level: 99 dB

This declaration is applicable to the product affixed CE marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses Produkt

den Standards oder standardisierten Dokumenten EN50144,

HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3 und/

oder EN61000-3-11 in Übereinstimmung mit den Direktiven des

Europarats 73/23/EWG, 89/336/EWG, 98/37/CE und/order 2000/

14/CE entspricht.

2000/14/CE

• Übereinstimmungsbeurteilungsverfahren: ANNEX VI

• Informierte Körperschaft: BSI Product Services, Maylands

Avenue Hemel Hempstead Herts HP2 4SQ UK

• Gemessener Schallleistungspegel: 97,65 dB

• Garantierter Schallleistungspegel: 99 dB

Diese Erklärung gilt für Produkte, die die CE-Markierung tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière respon-sabilité que

ce produit est conforme aux normes ou documents normalisés

EN50144, HD400, EN55014-1, EN55014-2, EN61000-3-2, EN61000-

3-3 et/ou EN61000-3-11 en accord avec les Directives 73/23/CEE,

89/336/CEE, 98/37/CE et/ou 2000/14/CE du Conseil.

2000/14/CE

• Procédure d’évaluation de conformité : ANNEXE VI

• Organisme notifié : BSI Product Services, Maylands Avenue

Hemel Hempstead Herts HP2 4SQ R-U

• Niveau de puissance sonore mesuré : 97,65 dB

• Niveau de puissance sonore garanti : 99 dB

Cette déclaration s’applique aux produits désignés CE.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Instruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste instruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer cuidadosamente y comprender estas instrucciones antes del uso.

207

Code No. C99104673 N

Printed in Japan

28. 11. 2001

Y. Hirano (EMO)

Hitachi Koki USA H30PV User manual

Brand: Hitachi Koki USA

Model: H30PV

Category: Power tools

Type: User manual

This manual is also suitable for

H 30PV

Download PDF

report

in other languages

italiano: Hitachi Koki USA H30PV Manuale utente
français: Hitachi Koki USA H30PV Manuel utilisateur
español: Hitachi Koki USA H30PV Manual de usuario
Deutsch: Hitachi Koki USA H30PV Benutzerhandbuch
Nederlands: Hitachi Koki USA H30PV Handleiding

Hitachi Koki USA H30PV User manual

This manual is also suitable for

Hitachi Koki USA H30PV User manual

in other languages

Related papers

Other documents