Craftsman 900745470 Owner's manual

Brand: Craftsman

Model: 900745470

Category: Power tools

Type: Owner's manual

This manual is also suitable for

C935.51850

TRIMMER/EDGER

U.S.A. Model 900.74547

Canada Model C935.51850

-&CAUTION:

Before using this product,

read this manual and follow

all its Safety Rules and

Operating Instructions.

• Safety

• Operation

• Maintenance

• EspaSol, 12

• Fran£ais, 21

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

www.sears.com/craftsman

Form No. 90529772 DEC. ' 07 Printed in China

auxiliary_, __ - trigger

handle __

nylon cutting line_b°_tversi°n

guard

[,._-] Lv;/;1:1:T;I_/ i_"d

CRAFTSMAN ONE YEAR FULL WARRANTY

If this Craftsman product fails due to a defect in material or workmanship within one

year from the date of purchase, return it to any Sears store or other Craftsman outlet in

the United States for free replacement.

This warranty does not include the cutting line, which is an expendable part.

This warranty applies for only 90 days from the date of purchase if this product is ever

used for commercial or rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using

this tool reads and understands all safety

instructions and other information

contained in this manual.

• Save these instructions and review

frequently prior to use and in instructing

others.

AWARNING: When using electric

gardening appliances, basic safety

precautions should always be followed to

reduce risk of fire, electric shock, and

personal injury, including the following:

READ ALL INSTRUCTIONS.

• ALWAYS WEAR EYE PROTECTION -

Wear safety spectacles or goggles at all

times when this tool is plugged in.

• GUARD - Do not use this tool without

guard attached.

• DRESS PROPERLY- Do not wear

loose clothing or jewelry. They can be

caught in moving parts. Rubber gloves

and substantial rubber soled footwear

are recommended when working

outdoors. Don't operate the tool when

barefoot or wearing open sandals. Wear

long pants to protect your legs. Wear

protective hair covering to contain long

hair.

• NYLONLINE- Keepface,handsand

feetclearofrotatingnylonlineatalltimes.

•THEROTATINGLINEPERFORMSA

CUTTINGFUNCTION- Usecarewhen

trimmingaroundscreensanddesirable

plantings.

• KEEPALLBYSTANDERSAWAY- ata

safedistancefromworkarea,especially

children.

• IMPORTANTWARNING- Whenbeing

usedasanEdger,stones,piecesof

metalandotherobjectscanbethrown

outathighspeedbytheline.Thetool

andguardaredesignedtoreducethe

danger.However,thefollowingspecial

precautionsshouldbetaken:

• MAKESUREthatotherpersonsand

petsareatleast100feet(30m)away.

•TOREDUCETHERISKofrebound

(ricochet)injury,workgoingawayfrom

anynearbysolidobjectsuchaswall,

steps,largestone,tree,etc.Usegreat

carewhenworkingclosetosolidobjects

andwherenecessary,doedgingor

trimmingbyhand.

•AVOIDACCIDENTALLYSTARTING-

Don'tcarryplugged-intoolwithfingeron

trigger.

• DONOTFORCETHETOOL- atarate

fasterthantherateatwhichitisableto

cuteffectively.

• USETHERIGHTTOOL-Donotusethis

toolforanyjobexceptthatforwhichitis

intended.

• DON'TOVERREACH- Keepproper

footingandbalanceatalltimes.

• DON'TABUSECORD- Don'tyankcord

frompowersupply.Keepcordfromheat,

oil,andsharpedges.

• DAMAGETOUNIT-Ifyoustrikeor

becomeentangledwithaforeignobject,

stoptoolimmediately,unplug,checkfor

damageandhaveanydamagerepaired

beforefurtheroperationisattempted.Do

notoperatewithabrokenhuborspool.

• DAMAGETOCORD- Keeppowercord

awayfromrotatingline.Ifyoudamage

thecord,unplugitfromthepowersupply

beforemovingthetoolorexaminingthe

damage.Adamagedcordmustbe

replacedbeforefurtheruse.

• DISCONNECTTOOL-whennotinuse,

whenreplacingline,orpriortocleaning.

•AVOIDDANGEROUS

ENVIRONMENTALCONDITIONS-Do

notuseelectrictoolsindamporwet

locations.Followallinstructionsinthis

InstructionManualforproperoperation

ofyourtool.Don'tusethetoolintherain.

• DONOTOPERATEportableelectric

toolsingaseousorexplosive

atmospheres.Motorsinthesetools

normallyspark,andthesparksmight

ignitefumes.

• STOREIDLE TOOLS INDOORS -

When not in use, tools should be stored

indoors in a dry, locked-up place out of

reach of children.

• GROUND FAULT CIRCUIT

INTERRUPTER (GFCI) protection

should be provided on the circuits or

outlets to be used for the gardening

appliance. Receptacles are available

having built in GFCI protection and may

be used for this measure of protection.

• SECURE EXTENSION CORD using the

cord retainer shown in Figure 7.

• STAY ALERT - Watch what you are

doing. Use common sense. Do not

operate tool when you are tired.

• MAINTAIN APPLIANCES WITH CARE

- Follow instructions in maintenance

section. Inspect extension cords

periodically and replace if damaged.

Keep handles dry, clean and free from oil

and grease.

• CHECK DAMAGED PARTS - Before

further use of the appliance, a guard or

other part that is damaged should be

carefully checked to determine that it will

operate properly and perform its

intended function. Check for alignment of

moving parts, binding of moving parts,

breakage of parts, mounting, and any

other condition that may affect its

operation. A guard or other part that is

damaged should be properly repaired or

replaced by an authorized service center

unless otherwise indicated elsewhere in

this manual.

_,WARNING: When servicing double

insulated tools, USE ONLY IDENTICAL

REPLACEMENT PARTS. Replace or

repair damaged cords.

AWARNING: Toprevent electrical shock

hazard, use only with an extension cord

suitable for outdoor use. Always connect

extension cords to a fused line or one

_protected by a circuit breaker.

WARNING: To reduce the risk of electric

shock use only with an extension cord

intended for outdoor use, such as SW-A,

SOW-A, STW-A, STOW-A, SJW-A,

SJOW-A, SJTW-A or SJTOW-A.

• EXTENSION CORD. Make sure your

extension cord is in good condition.

When using an extension cord be sure it

is heavy enough to carry the current your

product will draw. An undersized

extension cord will cause a drop in line

voltage resulting in loss of power and

overheating. The following table shows

thecorrectsizetousedependingon

cordlengthandnameplateampere

rating.Ifindoubt,usethenextheavier

gage.Thesmallerthegagenumber,the

heavierthecord.

_,ADDITIONAL WARNINGS FOR

STRING TRIMMERS

1. DO NOT immerse tool in water or

squirt it with a hose. DO NOT allow

any liquid to get inside it.

2. Do not store the tool on or adjacent to

fertilizers or chemicals.

3. DO NOT clean with a pressure

washer.

Minimum Gage for Extension Cords (AWG) 120

VAC Tools

TotalCord Length 0-25 26-50 51-100 105-150

Amp Rating AWG AWG AWG AWG

More than 0 18 16 16 14

Not More than 6

More than 6 18 16 14 12

Not More than 10

More than 10 16 16 14 12

Not more than 12

More than 12 14 12 Not

Not more than 16 Recommended

Double insulated tools are constructed

throughout with two separate layers of

electrical insulation or one double

thickness of insulation between you and

the tool's electrical system. Tools built

with this insulation system are not

intended to be grounded. As a result,

your tool is equipped with a two prong

plug which permits you to use extension

cords without concern for maintaining a

ground connection.

NOTE: Double insulation does not take

the place of normal safety precautions

when operating this tool. The insulation

system is for added protection against

injury resulting from a possible electrical

insulation failure within the tool.

Replacement parts: When servicing all

tools, USE IDENTICAL REPLACEMENT

PARTS. Repair or replace damaged

cords.

To reduce the risk of electric shock, this

equipment has a polarized plug (one

blade is wider than the other). This

equipment must be used with a suitable

polarized 2 wire or 3 wire extension cord.

Polarized connections will fit together

only one way. Make sure that the

receptacle end of the extension cord has

large and small blade slot widths. Ifthe

plug does not fit fully into the extension

cord, reverse the plug. If it still does not

fit, obtain a suitable extension cord. Ifthe

extension cord does not fit fully into the

outlet, contact a qualified electrician to

install the proper outlet. Do not change

the tool plug or extension cord in any

way.

_e]]_[_ [-%1=q'L'Akv,vl:1:t_II_[€]

_,WARNING: Some dust created when

using lawn and garden power tools

contains chemicals known to cause

cancer, birth defects and other

reproductive harm.

Some examples of these chemicals are:

• crystalline silica from sand, bricks and

other masonry dust

• arsenic and chromium from chemically

treated lumber (CCA)

• compounds in fertilizers

• compounds in insecticides, herbicides

and pesticides

Health risk from these chemical

exposures varies, depending on the

environment in which you are working and

how often you do this type of work. To

reduce your exposure to these chemicals,

follow product label instructions to apply

chemicals such as fertilizers, insecticides,

herbicides or pesticides. When using

these tools, wear safety equipment such

as gloves and dust masks which are

especially designed to filter out

microscopic particles.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE.

ASSEMBLY TOOLS REQUIRED (NOT

SUPPLIED):

- Phillips Screwdriver

ATTACHING THE TWO PIECE

GUARD

_t,WARNING: UNPLUG THE TOOL

BEFORE ATTEMPTING TO ATTACH

THE GUARD. NEVER OPERATE TOOL

WITHOUT GUARD FIRMLY IN PLACE.

THE GUARD MUST ALWAYS BE ON

THE TOOL TO PROTECT THE USER.

• Remove the two guard sections from

the carton.

• Attach the first guard section with side

tab into the groove around the housing

as shown in figure 1. Align the hole in

the guard with the post on the trimmer

housing.

• Insert the side tab from the first guard

section into the slot of the second guard

section until you hear them "snap"

together (figure 3).

Tab

Remove the screw from the second

guard section.

• Insert the top tab from the second

guard section into the first guard

section as shown in figure 2. NOTE:

The rib behind the tab should be

hooked over the rib of the first guard

section. (See inset figure 2).

Rib

• Insert the 3/4inch (19mm) screw as

shown in figure 4 to complete the guard

assembly.

• Once the guard is installed, remove the

covering from the line cut-off blade,

located on the edge of the second guard

section.

ATTACHING THE AUXILIARY

HANDLE

• Attach the handle to the metal shaft of

the trimmer by pushing it onto the shaft

from the side. Once it is pushed onto

the metal shaft, the handle can be

turned into the correct orientation.

• Insert the 2-1/2 inch (63.5mm) bolt

throughtheholesinthehandleand

threadontheplasticknobasshownin

figure 5.

ATTACHING EXTENSION CORD

• An extension cord retainer (figure 7) is

built into the switch handle that

prevents the cord from coming

unplugged. To use this feature, simply

double the extension cord about 8

inches (203mm) from the end, and

insert it into the slot in the bottom of

the handle area. Hook the loop formed

by doubling the cord over the tab.

Gently tug on the cord to insure that it

is firmly retained in the trimmer's

handle. Plug the receptacle end of the

extension cord into the plug blades in

the trimmer.

For maximum comfort and control,

adjust the auxiliary handle to suit your

height. Shorter users adjust handle to a

lower position (away from you) and

taller users, adjust handle to an upper

position (towards you). The handle

should be adjusted so that your front

arm is straight when the trimmer is in

the working position.

HEIG HT ADJ USTM ENT

• The overall height of the trimmer can

be adjusted by pressing the conversion

button shown in figure 6 and moving

the metal tube up or down into one of

the three rectangular recesses in the

tube until you hear it "snap" into place.

_, CAUTION: Confirm that the tube is

locked in place by releasing the button

and pushing down on the tube.

AWARNING: Always use proper eye

protection that conforms toANSI Z87. 1

(CAN/CSA Z94.3) while operating this

power tooL

ACAUTION: Inspect area to be trimmed

and remove any wire, cord, or string-like

objects which could become entangled

in the rotating line or spool. Be particularly

careful to avoid any wire which might be

bent outwardly into the path of the tool,

such as barbs at the base of a chain link

fence.

SWITCHING ON AND OFF

• To switch the tool on, squeeze the

trigger lever.

• To switch the tool off, release the

trigger lever.

• With the unit on, angle unit and slowly

swing the trimmer side to side as

shown in figure 8.

• To operate as a maintenance edger,

unplug the unit from the power source.

Push the conversion button and rotate

the tube 180° as shown in figure 6.

The tool will lock in position. Gently pull

the wire edge guide down into place as

shown in figure 9 and position the

trimmer above the surface as shown in

figure 9.

• Return to the trimming position by

unplugging the unit from the power

source, pushing the conversion button

and rotating the tube back 180°. The

tool will lock in the trimmer position.

When using the tool return the wire

edge guide to the original position, out

of the way.

BLOWER FUNCTION

(FIGURE 10)

The air flow created by the motor funnels

up through the guard to provide a built-in

blower. This feature can be used to blow

grass clippings off of sidewalks and other

hard surface areas.

CUTTING LINE / LINE FEEDING

Your trimmer uses .065 inch (1.65

mm) diameter, ROUND nylon line.

During use, the tips of the nylon lines

will become frayed and worn and the

special self feeding line hub will

automatically feed and trim a fresh

length of line. Cutting line will wear

faster and require more feeding if the

cutting or edging is done along

sidewalks or other abrasive surfaces

or heavier weeds are being cut. The

advancedautomaticlinefeeding

mechanismsenseswhenmorecutting

lineisneededandfeedsandtrimsthe

correctlengthoflinewheneverit's

required.DONOTBUMPuniton

groundinattempttofeedlineorfor

anyotherpurposes.

FITTING A NEW SPOOL OF AFS

CU'I-I'ING LINE (FIGURES 11 & 12)

• Unplug the tool.

• Depress the tabs (a) and remove the

cassette (b) from the cassette housing

• Grasp empty spool (d) with one hand

and cassette with other hand and pull

spool out from cassette. If lever (e) in

base of cassette becomes dislodged,

replace in correct position before

inserting new spool into cassette.

• Remove any dirt and grass from the

cassette and housing.

• Take the new spool and push it onto

the boss (f) (figure 12) in the cassette.

Rotate the spool slightly until it is seated.

• Unfasten the end of one of the cutting

lines and guide the line into one of the

eyelets (g) (figure 12}. The line should

protrude approximately 4-3/8 inches

(111mm) from the cassette.

• Unfasten the end of the other cutting

line and guide the line into the other

eyelet. The line should protrude

approximately 4-3/8 inches (111mm)

from the cassette.

• Align the cassette tabs (a) with the slots

(h) in the housing (figure 11).

• Push the cassette onto the housing

until it snaps securely into place.

CAUTION: To avoid tool damage, If the

cutting lines protrude beyond the

trimming blade (i), cut them off so that

they just reach the blade (figure 11).

WINDING NEW LINE ONTO AN

EMPTY SPOOL (FIGURES 13 &14)

You may wind new cutting line onto an

empty spool. Replacement packs of .065

inch (1.65 mm) cutting line are available

from your Sears store.

• Remove the empty spool from the tool

as described in "FITTING A NEW

SPOOL OF AFS CUTTING LINE".

• Remove any remaining cutting line

from the spool.

• First wind new line onto the uppermost

part of the spool.

- Feed 3/4 inch (19mm) of cutting line

into one of the line anchoring slots.

- Wind the cutting line onto the spool in

the direction of the arrow on the spool.

Make sure to wind the line neatly and in

layers. Do not crisscross (figure 13).

- When the wound cutting line reaches

the recesses (j), cut the line. (figure 14).

- Temporarily park the line in the holding

slots (k)on one side of the spool as

shown inthe inset in figure 14.

• Repeattheaboveprocedureforthe

secondcuttinglineonthelowersection

ofthespool.

• Fitthespoolontothetoolasdescribed

in"FITTINGANEWSPOOLOF

CUTTINGLINE".

_CAUTION:Beforeyoubegintrimming,

onlyusetheappropriatetypeofcutting

line.Ensurethatcuttinglineispresentin

bothsectionsofthespool(figure12).

2.Yourtrimmerlinecandryoutover

time.Tokeepyourlineintopcondition,

storesparepre-woundspoolsorbulk

lineinaplastic,sealablebagwitha

tablespoonofwater.

3.Plasticpartsmaybecleanedbyusing

amildsoapandadamprag.

4.Thelinecutterontheedgeoftheguard

candullovertime.Itisrecommended

youperiodicallytouch-upthe

sharpnessofthebladewithafile.

UseCraftsmanreplacementspoolModel

No.85942.

Reloadnylonline(eitherbulkorprewound

replacementspool)asdescribedinthis

manual.

• USEONLY.065 inch (1.65 mm)

DIAMETER NYLON MONOFILAMENT

LINE. Do not use serrated or heavier

gauge line, as they will overload the

motor and cause overheating. The unit

only functions properly with .065 inch

(1.65 mm) diameter nylon monofilament

line. This line is available at your local

Sears store or other Craftsman outlet.

_,WARNING: The use of any accessory

not recommended by Sears for use with

this tool could be hazardous.

IMPORTANT: To assure product SAFETY

and RELIABILITY, repairs, maintenance

and adjustment should be performed by a

Sears or other qualified service dealer,

always using identical replacement parts.

-4,WARNING: To avoid serious injury,

switch off and unplug the tool before

performing any maintenance.

1. Keep the air intake slots (figure 15)

clean to avoid overheating.

_t,WARNING: To avoid serious injury,

switch off and unplug the tool before

performing any maintenance.

Tool runs slowly

• Check that the cassette housing can

rotate freely. Carefully clean it if necessary.

• Check that the cutting line does not

protrude more than approximately 4-3/8

inches (111mm) from the cassette. If it

does, cut it off so that it just reaches the

line trimming blade.

Automatic line feed does not work

• Keep the tabs depressed and remove

the cassette from the cassette housing

in the trimmer head.

• Pull the cutting line until it protrudes

approximately 4-3/8 inches (111mm)

from the cassette. If insufficient cutting

line is left on the spool, install a new

spool of cutting line.

• Align the tabs on the cassette with the

cut outs in the housing.

• Push the cassette onto the housing

until it snaps securely into place.

• If the cutting line protrudes beyond the

trimming blade, cut it off so that it just

reaches the blade.

Iftheautomaticlinefeedstilldoesnot

workorthespoolisjammed,trythe

followingsuggestions:

• Carefullycleanthecassetteand

housing.

• Removethespoolandcheckifthe

leverinthecassettecanmovefreely.

• Removethespoolandunwindthe

cuttingline,thenwinditonneatly

again.Replacethespoolintothe

cassette.

NEED MORE HELP?

You'll find the answer and more on managemyhome.com - for free!

oFindthis and all your other product manuals online.

Getanswersfrom our team of home experts.

Geta personalized maintenance plan foryour home.

Findinformation and tools to help with home projects.

b:ought to yo::by Sea:s

Page is loading ...

Your Home

For expert troubleshooting and home solutions advice:

manage home

www.managemyhome.com

For repair - in your home - of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it !

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1=800=4=MY=HOME ® call anytime, day or night

(1=800-469-4663) (U.S.A. and Canada)

WWW,SeaFs=com www=seaFs=ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call anytime for the location of the nearest

Sears Parts & Repair Service Center

1=800=488=1222 (U.S.A.) 1=800=469=4663 (Canada)

www.seats=com www.sears,ca

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparacbn Au Canada pour service en fran£ais:

a domicilio, y para ordenar piezas: 1.800.LE.FOYERMC

l=888=SU=HOGAR® (1-800-533_937)

(1-888-784-6427) www.sears.ca

@Sears Brands, LLC

@ Registered Trademark / r_ Trademark / SMService Mark of Sears Brands, LLC

@ Marca Registrsda / T'_tMarca de Fabrica / SMMarca de Servicio de Sears Brands, LLC

_c Marque de commerce / MD Marque depos6e de Sears Brands, LLC

Craftsman 900745470 Owner's manual

Brand: Craftsman

Model: 900745470

Category: Power tools

Type: Owner's manual

This manual is also suitable for

C935.51850

Download PDF

report

in other languages

français: Craftsman 900745470 Le manuel du propriétaire
español: Craftsman 900745470 El manual del propietario

Craftsman 900745470 Owner's manual

This manual is also suitable for

Craftsman 900745470 Owner's manual

in other languages

Related papers

Other documents