Echo SRM-280T User manual

WARNING

You must install a Barrier Bar or U-Handle Kit and all Blade Conversion parts shown in the following instructions

before operating this unit with blades, otherwise serious injury may result.

SRM/PAS/SB BLADE SET-UP GUIDE*

TO USE

THESE BLADES

Pro Maxi-Cut

Grass/Weed

Plastic Cutters

Rigid Plastic

Tri-Cut

Grass/Weed Blade

Metal

Tri-Cut/8 Tooth

Grass/Weed Blade

Metal 80T Brush Blade

Metal 22T Clearing Saw Blade

Handle

Loop Handle, w/or

w/o Barrier Bar

Loop Handle

w/Barrier Bar,

or U-Handle

Loop Handle

w/Barrier Bar,

or U-Handle

U-Handle

Debris Shield Metal Shield Metal Shield Metal Shield Metal Shield

Harness Shoulder Harness Shoulder Harness Shoulder Harness Shoulder Harness****

Upper Plate &

Flat Washer

Upper Plate

& Glide Cup

Upper/Lower

Blade Plates**

Upper/Lower

Blade Plates**

Hex Nut Hex Nut Hex Nut Hex Nut

You

must

install

these

parts!

Blade

Mounting

Hardware

New Cotter Pin*** New Cotter Pin*** New Cotter Pin*** New Cotter Pin***

* WARNING! DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS

** Arbor diameter of Upper Blade Plate must match arbor diameter of metal blades.

*** New cotter pin required each time blade is installed.

**** Brushcutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness

U-Ha n d l e Ki t in s t a l l a t i o n

i

n s t r U c t i o n s P/N 99944200689

For Models: SRM-280/280S/280T S/N ALL

co n t e n t s

1 U-handle assembly

1 Lower u-handle bracket (2 halves)

1 Harness clamp w/ring

1 5 x 12 mm bolt

1 8 x 55 mm bolt

1 Circular washer

1 Square nut

2 Throttle cable clips

3 5 x 30 mm bolts w/washers

1 Shoulder harness

1 Hip pad

IMPORTANT

If non-standard monolament heads, METAL/PLASTIC blades or cultivators etc., are used, THE CARBURETOR

MUST BE RESET or serious engine damage can occur. See "Carburetor Adjustment" in the unit Operator's Manual.

X7502234701

X750011731

10/09

2

U-Ha n d l e Ki t in s t a l l a t i o n in s t r U c t i o n s

A

B

A

B

D

C

F

E

in s t a l l a t i o n

Tools Required: 8mm x 10mm Open End Wrench, 19 mm wrench

4 mm hex wrench, screwdriver

1. Close choke and remove air lter and cover.

2. Disconnect ignition stop leads (A) and (B).

3. Loosen nuts (C) and remove throttle linkage from carburetor

bracket.

4. Remove inner throttle cable from carburetor swivel (D).

5. Loosen the two (2) drive shaft clamp bolts (E) at engine drive

shaft clamp, and remove center drive shaft location bolt (F).

6. Pull drive shaft assembly from clutch case.

7. Loosen two (2) rear handle screws (G) and pull rear handle from

the drive shaft assembly.

8. Loosen two (2) screws (H) and remove front handle.

H

G

9. Insert square nut (I) in lower handle bracket (J) and place bracket

on drive shaft 400mm (15 3/4 in.) from engine end of drive shaft.

10. Secure with lower handle bracket clamp (K) and three (3) 5mm x

30mm hex socket bolts.

11. Position harness clamp (L) 220 mm (8-5/8 in.) from engine end of

drive shaft assembly. Install 5x12 mm bolt, but DO NOT tighten

at this time.

12. Carefully t drive shaft assembly to engine making sure inner

drive shaft engages into clutch socket.

13. Turn drive shaft housing until locating hole lines up with location

hole in clamp and install center drive shaft location bolt (F).

NOTE

Gear Housing must be aligned properly with engine. Aligning cen-

ter locating hole in driveshaft housing with center drive shaft bolt

(F) provides correct alignment.

14. Tighten two (2) drive shaft clamp bolts (E) securely.

15. Install upper U-Handle and bracket on lower bracket and secure

with one (1) 8 mm x 55 mm bolt (M) and large circular washer.

16. Route throttle linkage and ignition lead assembly behind U-Han-

dle bracket and clip to drive shaft as shown.

I

J

K

400 mm

(15-3/4 in.)

220 mm

(8-5/8 in.)

ENGINE

END

K

J

M

L

E

F

E

U-Ha n d l e Ki t in s t a l l a t i o n in s t r U c t i o n s

3

U-Ha n d l e Ki t in s t a l l a t i o n in s t r U c t i o n s

17. Place inner throttle cable in large hole of carburetor swivel (D).

18. Loosen nuts (C) and place threaded end of throttle linkage in

bracket slot. Finger tighten nuts (C).

19. Check throttle for freedom of movement and that wide open

throttle / low idle extremes are adjusted properly. If adjustment

cannot be achieved with adjusting nuts (C), consult with your

Echo Dealer for correct adjustment procedure. Tighten nuts (C).

20. Connect 2 ignition stop leads (A,B) from throttle cable tubing to 2

ignition leads (A,B) on engine.

21. Gather ignition wires and position behind air lter case.

22. Install air lter and cover

Install Hip Pad (Optional)

1. Attach hip pad to harness as shown.

A

B

A

B

4

D

C

U-Ha n d l e Ki t in s t a l l a t i o n in s t r U c t i o n s

e c H o c o n s U m e r p r o d U c t s U p p o r t

If you require assistance or have questions concerning the application, operation or maintenance of this product you may

call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to 4:30 pm (Central Standard

Time) Monday through Friday. Before calling, please know the model and serial number of your unit to help your Con-

sumer Product Support Representative.

ECHO, INCORPORATED

400 OAKWOOD ROAD

LAKE ZURICH, IL 60047 USA

PHONE: 1-800-673-1558

www.echo-usa.com

L

N

Balance and Adjust Unit

1. Loosen harness clamp screw.

2. Put on harness and attach unit to harness.

3. Slide harness clamp (L) up or down until unit balances with head

approximately 50-75 mm (2 -3 in.) from the ground.

4. Tighten harness clamp screw.

5. Loosen upper U-Handle clamp screws (N), and position U-Handle

for comfortable operation.

6. Tighten U-Handle clamp screws and 8 mm clamp bolt securely.

NOTE

In case of Emergency, the trimmer/brushcutter can be released from

the harness by pulling up on the quick-release collar.

5

Page is loading ...

ECHO, INCORPORATED

400 OAKWOOD ROAD

LAKE ZURICH, IL 60047 USA

PHONE: 1-800-673-1558

www.echo-usa.com

Echo SRM-280T User manual

Echo SRM-280T User manual

in other languages

Related papers

Other documents