American Standard Tendence T086.500 User manual

American Standard
Brand
American Standard
Model
Tendence T086.500
Category
Sanitary ware
Type
User manual

American Standard Tendence T086.500 is a bath/shower trim kit with EverClean™ finish found only on American Standard faucets. EverClean Finish effortlessly removes spots, eliminates the need for cleaners and scrubbing, and remains beautiful for the life of the faucet. This finish is available on Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes). The trim kit is certified to comply with ANSI A112.18.1 and U.S. Patent No. D403,750.

American Standard Tendence T086.500 is a bath/shower trim kit with EverClean™ finish found only on American Standard faucets. EverClean Finish effortlessly removes spots, eliminates the need for cleaners and scrubbing, and remains beautiful for the life of the faucet. This finish is available on Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes). The trim kit is certified to comply with ANSI A112.18.1 and U.S. Patent No. D403,750.

U.S. Patent No. D403,750
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
To assure proper positioning in relation to wall,
note roughing-in dimensions.
T086.502
T086.501
T086.500
TENDENCE
BATH/SHOWER TRIM KIT
FINISHED WALL
4"
TOP OF TUB RIM
BOTTOM OF TUB
74" FOR HEAD CLEARANCE
1-5/8"" TO 3-1/4"
5" REF.
1/2" NPT
7-5/8"
7"
1/2" NPT
48"
(OPTIONAL)
1/2" REF.
1-1/2" MIN.
1-1/2" REF.
M968388 Rev. 1.1
with EverClean™ Finish
Congratulations on purchasing your American Standard faucet with
EverClean finish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Installation
Instructions
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 80''
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
INSTALL TRIM
1
Remove PLASTER GUARD (1).
Push CAP (2) on valve, place ESCUTCHEON HOLDER
(3) and attach with LONG SCREWS (4).
Place ESCUTCHEON (5) and attach with SHORT
SCREWS (6).
Choose one of the DECORATIVE RINGS (7)
and push it onto CAP (2).
Push HANDLE (11) onto cartridge stem
and tighten SET SCREW (12) from below.
NOTE: Lift handle to access SET
SCREW (12)
Install SHOWER ARM (8), SHOWER HEAD (9)
and DIVERTER SPOUT (10).
Check proper operation of HANDLE (11)
and DIVERTER SPOUT (10).
10
2
3
5
6
7
11
12
4
9
8
6
1
M968388 Rev. 1.1
3
EverClean™ Finish Care Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
2
ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to
adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING FORWARD AND ROTATE
COUNTER-CLOCKWISE ONE CLICK
PRY RED RING FORWARD AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN WATER IS TOO HOT
"A"
"B"
"B"
ADJUSTMENT WHEN WATER IS TOO COLD
"RED RING"- HOT LIMIT SAFETY STOP
TEMPERATURE SETTING NUMBERS
0
1
2
3
4
5
6
1
  • Page 1 1
  • Page 2 2

American Standard Tendence T086.500 User manual

American Standard
Brand
American Standard
Model
Tendence T086.500
Category
Sanitary ware
Type
User manual

American Standard Tendence T086.500 is a bath/shower trim kit with EverClean™ finish found only on American Standard faucets. EverClean Finish effortlessly removes spots, eliminates the need for cleaners and scrubbing, and remains beautiful for the life of the faucet. This finish is available on Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes). The trim kit is certified to comply with ANSI A112.18.1 and U.S. Patent No. D403,750.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers