Force10 CH-C300 Datasheet

Category
Power supply units
Type
Datasheet

This manual is also suitable for

C-Series Resilient Switches
The Force10 Networks C-Series are resilient chassis-based switches that deliver reliability, network control
and scalability. The C-Series is designed to support mission critical applications with very low latency
across converged networks. Comprehensive management capabilities make the C-Series a cost-effective
and flexible deployment option.
Key Applications
Low cost 100/1000 Mbps server aggregation for small- to medium-sized data centers
(100s to 1,000s of servers)
Cost-effective LAN core switch for small- and medium-campuses (100s to 1,000s of PCs)
High density GbE aggregation for distribution into a multiple Gbps or 10 GbE backbone
Cost-effective PoE-enabled 10/100/1000Base-T wiring closet aggregation of VoIP phones, wireless
access points, video cameras or other IEEE 802.3af-compliant devices
Key Features
The Force10 C-Series is designed to provide inherent reliability,
network control, and scalability for high performance Ethernet
environments.
Up to 384 line-rate 10/100/1000Base-T ports with full 15.4 W
Class 3 PoE support in a 13-RU chassis
Up to 64 line-rate 10 GbE ports with pluggable XFP modules
Suite of security, access control and wiring closet edge features for enterprise networks
VirtualView real-time network and application traffic monitoring for virtualized data centers
PowerSmart intelligent power management features provide automatic sensing, provisioning and
management of PoE power
Full complement of standards-based Layer 2, IPv4 and IPv6 features for unicast and multicast applications
5 microsecond switching latency under full load for 64 byte frames
Switch fabric capacity of up to 1.536 Tbps and up to 952 Mpps L2/L3 packet forwarding capacity
High availability architecture
1+1 Route Processor Module (RPM) design
Continuous runtime data plane monitoring and
advanced in-service CLI diagnostic functions
Power supply redundancy with load sharing
power bus enabling uninterrupted VoIP calls
during a power supply failure
Modular Force10 Operating System (FTOS)
software delivers inherent stability
In-service diagnostics and traffic visibility
tools increase control of network
Line-rate, non-blocking GbE and 10 GbE
performance
C-SERIES
C150
C300 Resilient Switches
© 2009 Force10 Networks, Inc. All rights reserved. Force10 Networks, Adit,
E-Series, Traverse, and TraverseEdge are registered trademarks and Axxius,
C-Series, ExaScale, FTOS, MASTERseries, P-Series, S-Series, TeraScale, and
TransAccess are trademarks of Force10 Networks, Inc. All other company names
are trademarks of their respective holders. Information in this document is subject
to change without notice. Certain features may not yet be generally available.
Force10 Networks, Inc. assumes no responsibility for any errors that may appear
in this document.
CSDS02 809 v3.4
Force10 Networks, Inc.
350 Holger Way
San Jose, CA 95134 USA
www.force10networks.com
408-571-3500 PHONE
408-571-3550 FACSIMILE
Chassis
C300 – 8 line card slots
2 Route processor module with integrated switch fabric slots
8 Power supply module slots and 1 fan tray slot
Size: 13 RU, 22.7 h x 17.4 w x 14.4" d (57.66 h x 44.2 w x 37.58 cm d)
Weight with factory-installed components: 55 lbs (24.95 kg)
Weight fully loaded: 152.27 lbs (69.07 kg)
ISO 7779 A-weighted sound pressure level: 73.8 dBA at 73.4°F (23°C)
AC power
Nominal input voltage: 100–240 VAC 50/60 Hz
Maximum thermal output: 4,978 BTU/h (1,498 W) at 100/120 VAC
4,864 BTU/h (1,459 W) at 200/220 VAC
Maximum input current per module:
14 A at 100 VAC, 12 A at 120 VAC, 7 A at 200 VAC, 6 A at 240 VAC
Maximum system power input:
8.7 KVA at 100/120 VAC, 8.5 KVA at 200/240 VAC
Maximum power consumption:
8,675 W at 100/120 VAC, 8,476 W at 200/240 VAC
DC power
Nominal input voltage: –44 to –55 VDC
Maximum thermal output: 4,231 BTU/h (1,240 W)
Maximum current draw per DC PEM: 32 A
Maximum power consumption: 1,460 W
C150 – 4 line card slots
2 Route processor module with integrated switch fabric slots
6 Power supply module slots and 1 fan tray slot
Size: 9 RU, 15.7 h x 17.5 w x 15.3" d (39.88 h x 44.45 w x 38.86 cm d)
Weight with factory-installed components: 38 lbs (17.24 kg)
Weight fully loaded: 86.63 lbs (39.29 kg)
ISO 7779 A-weighted sound pressure level: 69.3 dBA at 73.4°F (23°C)
AC power
Nominal input voltage: 100–240 VAC 50/60 Hz
Maximum thermal output: 2,891 BTU/h (862 W) at 100/120 VAC
2,824 BTU/h (840 W) at 200/220 VAC
Maximum input current per module:
14 A at 100 VAC, 12 A at 120 VAC, 7 A at 200 VAC, 6 A at 240 VAC
Maximum system power input:
4.5 KVA at 100/120 VAC, 4.4 KVA at 200/240 VAC
Maximum power consumption:
4,420 W at 100/120 VAC, 4,319 W at 200/240 VAC
DC power
Nominal input voltage:
44 to –55 VDC
Maximum thermal output: 2,457 BTU/h (720 W)
Maximum current draw per DC PEM: 32 A
Maximum power consumption: 800 W
Common
19" front rack mountable
Maximum operating specifications:
Temperature: 32° to 104°F (0° to 40°C)
Altitude: no performance degradation to 10,000 feet (3,048 meters)
Relative humidity: 5 to 85% (RH), non-condensing
Maximum non-operating specifications:
Temperature: -40° to 158°F (-40° to 70°C)
Maximum altitude: 15,000 feet (4,572 meters)
Relative humidity: 5 to 95% (RH), non-condensing
Redundancy/Availability
1+1 redundant Switch Fabric & Route Processor Modules (RPM)
C300: 2+1 redundant system AC Power Supply Modules
1+1 redundant system DC Power Entry Modules
4+1 redundant PoE Power Supply Modules supporting up to
384 PoE ports at 15.4 W with deterministic failure mode
C150: 1+1 redundant system AC Power Supply Modules
1+1 redundant system DC Power Entry Modules
2+2 redundant PoE Power Supply Modules supporting up to
192 PoE ports at 15.4 W with deterministic failure mode
Online insertion and removal of all components
Environmental self-monitoring
Performance
MAC addresses: C150: 256K, C300: 512K
IPv4 routes: 12K
IPv6 routes: 6K
Switching fabric capacity: C150: 768 Gbps (476 Mpps)
C300: 1,536 Tbps (952 Mpps)
Link aggregation: 8 links per group, 128 groups per chassis
Queues per port: 4 queues
VLANs: 1024 VLANs with 4096 tag value support
Line-rate Layer 2 switching: all protocols, including IPv4 and IPv6
Line-rate Layer 3 routing: IPv4 and IPv6
LAG load balancing: based on Layer 2, IPv4 or IPv6 headers
Switching latency: <5 µs for 64 byte frames
IEEE Compliance
802.1AB LLDP
802.1D Bridging, STP
802.1p L2 Prioritization
802.1Q VLAN Tagging, Double VLAN Tagging, GVRP
802.1s MSTP
802.1w RSTP
802.1X Network Access Control
802.3ab Gigabit Ethernet (1000BASE-T)
802.3ac Frame Extensions for VLAN Tagging
802.3ad Link Aggregation with LACP
802.3ae 10 Gigabit Ethernet (10GBASE-X)
802.3af Power over Ethernet
802.3ak 10 Gigabit Ethernet (10GBASE-CX4)
802.3i Ethernet (10BASE-T)
802.3u Fast Ethernet (100BASE-FX, 100BASE-TX)
802.3x Flow Control
802.3z Gigabit Ethernet (1000BASE-X)
ANSI/TIA-1057 LLDP-MED
Force10 FRRP (Force10 Redundant Ring Protocol)
Force10 PVST+
MTU 9,252 bytes
RFC and I-D Compliance
General Internet Protocols
768 UDP
793 TCP
854 Telnet
959 FTP
1321 MD5
General IPv4 Protocols
791 IPv4
792 ICMP
826 ARP
1027 Proxy ARP
1035 DNS (client)
1042 Ethernet Transmission
1191 Path MTU Discovery
1305 NTPv3
1519 CIDR
1542 BOOTP (relay)
General IPv6 Protocols
1981
Path MTU Discovery (partial)
2460 IPv6
2461
Neighbor Discovery (partial)
2462 Stateless Address
Autoconfiguration (partial)
2463 ICMPv6
RIP
1058 RIPv1
OSPF
1587 NSSA
2154 MD5
2328 OSPFv2
2370 Opaque LSA
BGP
1997 Communities
2385 MD5
2439 Route Flap Damping
2545 Multiprotocol Extensions
for IPv6
2796 Route Reflection
2842 Capabilities
draft-ietf-idr-bgp4-20 BGPv4
draft-ietf-idr-restart-06 Graceful Restart
Multicast
1112 IGMPv1
2236 IGMPv2
3376 IGMPv3
3569 SSM for IPv4
Network Management
1155 SMIv1
1156 Internet MIB
1157 SNMPv1
1212 Concise MIB Definitions
1215 SNMP Traps
1493 Bridges MIB
1850 OSPFv2 MIB
1901 Community-based
SNMPv2
2011 IP MIB
2012 TCP MIB
2013 UDP MIB
2024 DLSw MIB
2096 IP Forwarding Table MIB
2570 SNMPv3
2571 Management Frameworks
2572 Message Processing and
Dispatching
2574 SNMPv3 USM
2575 SNMPv3 VACM
2576 Coexistence Between
SNMPv1/v2/v3
2578 SMIv2
2579 Textual Conventions for
SMIv2
2580 Conformance Statements
for SMIv2
2618 RADIUS Authentication MIB
2665 Ethernet-like Interfaces MIB
2674 Extended Bridge MIB
2787 VRRP MIB
2819 RMON MIB
(groups 1, 2, 3, 9)
2863 Interfaces MIB
Regulatory Compliance
Safety
UL/CSA 60950-1, 1st Edition
EN 60950-1, 1st Edition
IEC 60950-1, 1st Edition Including all National Deviations
and Group Differences
EN 60825-1 Safety of Laser Products Part 1:
Equipment Classification Requirements and User's Guide
EN 60825-2 Safety of Laser Products Part 2:
Safety of Optical Fibre Communication Systems
FDA Regulation 21 CFR 1040.10 and 1040.11
Emissions
Australia/New Zealand: AS/NZS CISPR 22: 2006, Class A
Canada: ICES-003, Issue-4, Class A
Europe: EN 55022: 2006 (CISPR 22: 2006), Class A
Japan: VCCI V3/2007.04 Class A
USA: FCC CFR 47 Part 15, Subpart B, Class A
Immunity
EN 300 386 V1.3.3: 2005 EMC for Network Equipment
EN 55024: 1998 + A1: 2001 + A2: 2003
EN 61000-3-2: Harmonic Current Emissions
EN 61000-3-3:Voltage Fluctuations and Flicker
EN 61000-4-2: ESD
EN 61000-4-3: Radiated Immunity
EN 61000-4-4: EFT
EN 61000-4-5: Surge
EN 61000-4-6: Low Frequency Conducted Immunity
RoHS
All C-Series components are EU RoHS compliant.
Ordering Information
O
RDER
N
UMBER
D
ESCRIPTION
CH-C150 C150 4-slot chassis with backplane
CH-C300 C300 8-slot chassis with backplane
CC-C150-FAN2 C150 enhanced fan subsystem
CC-C300-FAN2 C300 enhanced fan subsystem
LC-CB-RPM Switch Fabric and Route Processor
Module (series CB)
LC-CB-10GE-4P 4-port 10 Gigabit Ethernet line card,
XFP modules required (series CB)
LC-CB-10GE-8P 8-port 10 Gigabit Ethernet line card,
XFP modules required (series CB)
LC-CB-GE-48P 48-port Gigabit Ethernet line card,
SFP modules required (series CB)
LC-CB-GE-48T 48-port 10/100/1000Base-T line card
with RJ45 interfaces (series CB)
LC-CB-GE-48V 48-port 10/100/1000Base-T line card
with RJ45 interfaces and PoE (series CB)
LC-CB-10G-1G-36T FlexMedia line card with 36
10/100/1000Base-T RJ45 interfaces,
eight GbE interfaces – SFP modules
required, and two 10 GbE interfaces –
SFP+ modules required (series CB)
LC-CB-10G-1G-36V FlexMedia line card with 36
10/100/1000Base-T RJ45 interfaces with
PoE, eight GbE interfaces – SFP modules
required, and two 10 GbE interfaces –
SFP+ modules required (series CB)
CC-C-1200W-AC 1200 W AC Power Supply Module
CC-C-PWR-DC 1400 W DC Power Entry Module
SW-CB-LATEST FTOS software
Specifications: C-Series Resilient Switches
1350 TFTP
2474 Differentiated Services
3164 Syslog
draft-ietf-bfd-base-03 BFD
2858 Multiprotocol Extensions
2918 Route Refresh
3065 Confederations
4360 Extended Communities
4893 4-byte ASN
5396 4-byte ASN Representation
4541 IGMPv1/v2 Snooping
draft-ietf-pim-sm-v2-new-05
PIM-SM for IPv4
2865 RADIUS
3273 RMON High Capacity MIB
3376 IGMPv3
3416 SNMPv2
3418 SNMP MIB
3434 RMON High Capacity
Alarm MIB
3580 802.1X with RADIUS
5060 PIM MIB
ANSI/TIA-1057
LLDP-MED MIB
draft-grant-tacacs-02
TACACS+
draft-ietf-idr-bgp4-mib-06
BGP MIBv1
IEEE 802.1AB
LLDP MIB, LLDP DOT1
MIB, LLDP DOT3 MIB
ruzin-mstp-mib-02
MSTP MIB (traps)
sFlow.org sFlowv5
sFlow.org sFlowv5 MIB
(version 1.3)
FORCE10-BGP4-V2-MIB
FORCE10-CS-CHASSIS-MIB
FORCE10-IF-EXTENSION-MIB
FORCE10-LINKAGG-MIB
FORCE10-COPY-CONFIG-MIB
FORCE10-MON-MIB
FORCE10-PRODUCTS-MIB
FORCE10-SMI
FORCE10-SYSTEM-COMPONENT-MIB
FORCE10-TC-MIB
FORCE10-TRAP-ALARM-MIB
1812 Routers
1858 IP Fragment Filtering
2131 DHCP (server and relay)
2338 VRRP
3021 31-bit Prefixes
3046 DHCP Option 82
3069 Private VLAN
3128 Tiny Fragment Attack
Protection
2464 Ethernet Transmission
2675 Jumbograms
3587 Global Unicast Address
Format
4291 Addressing
2453 RIPv2
2740 OSPFv3
3623 Graceful Restart
4222 Prioritization and
Congestion Avoidance
  • Page 1 1
  • Page 2 2

Force10 CH-C300 Datasheet

Category
Power supply units
Type
Datasheet
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI