Kingston Technology KVR16E11/2I Datasheet

KVR16E11/2I
Kingston Technology
Brand
Kingston Technology
Model
KVR16E11/2I
Category
Memory modules
Type
Datasheet

Kingston Technology KVR16E11/2I is a 2GB DDR3-1600 CL11 SDRAM memory module designed for use in computers and servers. It features a JEDEC standard 1.5V power supply, 8 independent internal banks, programmable CAS latency, and on-DIMM thermal sensor. This memory module is compatible with Intel platforms and has been tested to meet nine electrical and mechanical specifications. It is also RoHS compliant and has an operating temperature range of 0°C to 85°C.

Kingston Technology KVR16E11/2I is a 2GB DDR3-1600 CL11 SDRAM memory module designed for use in computers and servers. It features a JEDEC standard 1.5V power supply, 8 independent internal banks, programmable CAS latency, and on-DIMM thermal sensor. This memory module is compatible with Intel platforms and has been tested to meet nine electrical and mechanical specifications. It is also RoHS compliant and has an operating temperature range of 0°C to 85°C.

KVR16E11/2I
2GB 1Rx8 256M x 72-Bit PC3-12800
CL11 ECC 240-Pin DIMM
DESCRIPTION
This document describes ValueRAM's 256M x 72-bit (2GB)
DDR3-1600 CL11 SDRAM (Synchronous DRAM)1Rx8, ECC,
Intel
®
Compatibility Tested, memory module, based on nine
256M x 8-bit FBGA components. The SPD is programmed to
JEDEC standard latency DDR3-1600 timing of 11-11-11 at
1.5V. This 240-pin DIMM uses gold contact fingers. The
electrical and mechanical specifications are as follows:
FEATURES
• JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 800MHz fCK for 1600Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB : Height 1.180” (30.00mm), single sided component
Document No. VALUERAM1101-001.A00 04/25/12 Page 1
Memory Module Specifi cations
SPECIFICATIONS
CL(IDD) 11 cycles
Row Cycle Time (tRCmin) 48.125ns (min.)
Refresh to Active/Refresh 160ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 35ns (min.)
Maximum Operating Power 2.497 W*
UL Rating 94 V - 0
Operating Temperature 0
o
C to 85
o
C
Storage Temperature -55
o
C to +100
o
C
*Power will vary depending on the SDRAM used.
Continued >>
MODULE DIMENSIONS:
Document No. VALUERAM1101-001.A00 Page 2
Units: millimeters
30.00
18.80
15.80
11.00
8.00
0.00
133.35
0.00
54.70
TECHNOLOGY
  • Page 1 1
  • Page 2 2

Kingston Technology KVR16E11/2I Datasheet

KVR16E11/2I
Kingston Technology
Brand
Kingston Technology
Model
KVR16E11/2I
Category
Memory modules
Type
Datasheet

Kingston Technology KVR16E11/2I is a 2GB DDR3-1600 CL11 SDRAM memory module designed for use in computers and servers. It features a JEDEC standard 1.5V power supply, 8 independent internal banks, programmable CAS latency, and on-DIMM thermal sensor. This memory module is compatible with Intel platforms and has been tested to meet nine electrical and mechanical specifications. It is also RoHS compliant and has an operating temperature range of 0°C to 85°C.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers