Clarion S660 User manual

MMooddeell SS666600

➤

OOwwnneerr’’ss GGuuiiddee

i

lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy

This Ungo Pro Security system is warranted against defects in material and workmanship.

The main unit is covered by this limited lifetime warranty. This Limited Lifetime

Warranty applies to Ungo Pro Security systems that have been installed by an authorized

Ungo Pro Security dealer. This warranty is to the Original Purchaser ("Owner") and to

the original vehicle in which it was installed into. This warranty is not transferable to any

subsequent owner(s) of the product(s).

WWaarrrraannttyy PPrrooggrraamm::

Main Unit Limited Lifetime

Remote Controls One year from date of purchase

Siren One year from date of purchase

Shock Sensor One year from date of purchase

LED One year from date of purchase

Override Switch One year from date of purchase

The Warranty does not cover batteries or products deemed damaged through alterations

or installation. It also does not cover products mishandled, misused, neglected, abused,

water damaged, or with removed/altered serial numbers.

PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF

THIS PRODUCT.

This warranty does not cover the costs incurred for removal or reinstallation of the main

unit and/or any damage to the vehicle or the vehicle's electrical system.

The sole responsibility of Clarion Corporation of America ("Clarion") under this

Warranty shall be limited to the repair or replacement of the product, at the sole discre-

tion of Clarion.

If it becomes necessary to send the product or any defective part to Clarion, the product

must be shipped in its original carton or equivalent carton, fully insured, with shipping

charges prepaid. Clarion will not assume any responsibility for any loss or damage

incurred in shipping.

ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY

APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE

WARRANTY PERIOD SET FORTH ABOVE. UNDER NO CIRCUMSTANCES

SHALL CLARION CORPORATION BE LIABLE FOR ANY LOSS OR DAMAGE,

DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY

TO USE OF THE PRODUCT. BECAUSE SOME STATES DO NOT ALLOW LIMI-

ii

TATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS

OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE

ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY

ALSO HAVE THE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

Should you have any difficulties with the performance of this product during warranty,

please call: 1-800-GO-CLARION or visit your local Ungo Pro Security dealer. You may

also contact the National Service Manager at the following address below for additional

service help you may need.

Clarion Corporation of America

Attn: National Service Manager

661 W. Redondo Beach Blvd.

Gardena, Ca 90247

1

ttaabbllee ooff ccoonntteennttss

lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. ii

rreemmoottee ccoonnffiigguurraattiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33

LCD 2-way configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

standard 4-button configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

wwhhaatt iiss iinncclluuddeedd.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 66

iimmppoorrttaanntt iinnffoorrmmaattiioonn .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 66

system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

rreemmoottee ffuunncctti

ioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 99

LCD 2-way remote standard configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Standard LCD 2-way icon configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4-button remote standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

LLCCDD 22--wwaayy rreemmoottee ooppeerraattiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. 1177

system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

uussiinngg yyoouurr ssyysstteemm .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1199

warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

active arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

warn away

®

response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

triggered response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

arming while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

disarming while driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

disarming without a remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

valet

®

mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

temperature check mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

nuisance prevention circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

ddiiaaggnnoossttiiccss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. 3300

arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

2

ccooddee hhooppppiinngg .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3344

hhiigghh ffrreeqquueennccyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3355

oowwnneerr rreeccooggnniittiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3355

rraappiidd rreessuummee llooggiicc .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3366

ppoowwe

err ssaavveerr mmooddee .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3366

pprrooggrraammmmiinngg ooppttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3377

sseeccuurriittyy && ccoonnvveenniieennccee eexxppaannssiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3399

gglloossssaarryy ooff tteerrmmss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4411

3

rreemmoottee ccoonnffiigguurraattiioonnss

LCD 2-way configuration

1234

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

➜

4

1 Vehicle Interior Temperature Indicator

2 Numeric Display

3 AM/PM Indicator

4 Alarm Clock Mode Indicator

5 Timer Function Indicator

6 Transmit Range Indicator

7 Transmission Indication

8 Vibrate/Beep Mode Indicator

9 Power Saver Mode Indicator

10 Remote Start Timer Mode Indicator

11 No Function

12 Vehicle Page Mode Indicator

13 Full Trigger Shock Sensor Indicator

14 Hood/Trunk Open or Trigger Indicator

15 Parking Light Indicator

16 Door Open or Trigger Indicator

17 Arm/Lock Button

18 Disarm/Unlock Button

19 Remote Start Indicator

20 Hood/Trunk Open or Trigger Indicator

21 Remote Start Button

22 Valet

®

Mode Indicator

23 Remote Start Safety Shutdown Indicator

24 Battery Level Indicator

25 Auxiliary Button

26 Temperature-Controlled Remote Start Indicator

27 Silent Arm/Disarm Mode Indicator

28 Full Trigger Alert Indicator

29 Arm/Disarm Indicator

30 Function Button

31 Celsius/Fahrenheit Indicator

5

standard 4-button configuration

controls the

AArrmm

and

PPaanniicc

On/Off function.

controls the

DDiissaarrmm

and

PPaanniicc

Off function.

controls

SSiilleenntt MMooddee™™

and

AAuuxxiilliiaarryy

channel

22

output.

no function.

and pressed together control channel

44

output.

and pressed together control channel

55

output

➜

6

wwhhaatt iiss iinncclluuddeedd

➤ Control module

➤ ASK transceiver/antenna

➤ One 4-button remote

➤ One 2-way LCD remote

➤ Stinger™ DoubleGuard

®

2-stage shock sensor

➤ Revenger™ Soft Chirp™ 6-tone programmable siren

➤ Status LED indicator light

➤ Push-button Valet

®

switch

iimmppoorrttaanntt iinnffoorrmmaattiioonn

Congratulations on the purchase of your remote alarm system.

Due to the complexity of this system, it must be installed by an

authorized dealer only. Installation of this product by anyone

other than an authorized dealer voids the warranty. All dealers

are provided with a preprinted dealer certificate to verify autho-

rization.

By carefully reading this Owner's Guide prior to using your

system, you will maximize the use of this system and its features.

You can print additional or replacement copies of this manual by

accessing our web site at www.clarion.com.

7

system maintenance

The system requires no specific maintenance other than battery

replacement for the remotes.

LCD 2-Way Remote Battery Replacement

The 2-way remote is powered by a 1.5V AAA battery. The

Battery Level indicator has three level indicators that serve as a

visual indication of battery charge. When the battery reaches a

low charge level that requires replacement, the transceiver will

generate a single notification chirp, and the Battery Level indi-

cator will flash continuously.

To replace the battery, gently pull the battery cover release tab, then

slide the door down to expose the battery and remove the expired

battery. Place the new battery into the transceiver observing the

correct polarity. When power is returned the transceiver will light

all icons in the LCD and generate all beeper tones once.

4-Button Remote Battery Replacement

Your remote is powered by a small, lightweight 3-volt lithium

battery (CR2032) that will last approximately one year under

normal use. When the battery begins to weaken, operating range

will be reduced and the LED on the remote will dim.

➜

8

fcc/id notice

This device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesirable operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

Tested to Comply

with FCC Standards

Directed Electronics, Inc. 474V/P/S Series

Tested to Comply

with FCC Standards

Directed Electronics, Inc. 477T Series

Tested to Comply

with FCC Standards

Directed Electronics, Inc. 544 Series

➜

9

rreemmoottee ffuunnccttiioonnss

The remote buttons are used to send commands to the system.

The descriptions below reflect the standard configuration for this

system. The buttons can be custom configured for the user’s

specific needs by the installer.

LCD 2-way remote standard configuration

LCD 2-way button configuration

Button

The System Arm/Lock and Multi-Level Security Arming func-

tions are controlled by pressing this button.

Button

The System Disarm/Unlock and High Security Disarm functions

are controlled by pressing this button.

Button

Channel 2 output is controlled by pressing and holding this

button for two seconds.

Button

The panic feature is controlled by pressing and holding this

button for three seconds. Press again to disable panic mode.

Button

The LCD backlighting will turn on when pressed for less than one

second; when held for more than five seconds the transceiver will

enter adjustment mode allowing the setting of the clock, timer

mode, and audible melody selection. For more information, please

refer to the

Function Button Configurations

section of this guide.

➜

10

Button

When pressed and held this button activates the second unlock

or other accessory.

and Buttons

The numeric display toggles between the time of the day and the

alarm clock when these buttons are pressed simultaneously.

and Buttons

Press these buttons simultaneously to activate the parking timer.

Each additional press will toggle through the available options

(10 min., 20 min., 30 min., 1 hour, 1.5 hours, 2 hours, and off).

and Buttons

When pressed simultaneously these buttons toggle between beep

notification and vibrate notification.

11

and Buttons

When pressed simultaneously these buttons activate battery saver

mode, which will drop power consumption on the transceiver

battery to zero when the alarm is inactive or disarmed.

Standard LCD 2-way icon configuration

Icon

The numeric display icon will show the hours and minutes.

Icon

The AM/PM icon indicates the time before or after noon.

Icon

The alarm clock mode icon indicates that the alarm clock mode

is active.

Icon

The timer function icon flashes during timed functions including

parking timer.

Icon

The transmit range indicator icon stays visible as long as the

system is within operating range.

➜

12

Icon

The remote transmission indicator icon displays when the trans-

ceiver is transmitting a signal.

Icon

The vibrate/beep mode icon appears when the transceiver is set

to vibrate mode.

Icon

The power saver mode can be turned on or off with the trans-

ceiver. This icon displays the status.

Icon

No function.

Icon

The vehicle page mode icon displays when the alarm module is

paging the transceiver.

Icon

The full trigger shock sensor icon indicates that the shock sensor

has been triggered by a hard shock.

and Icons

The hood/trunk open or trigger icon illuminates when the hood

or trunk trigger has been activated or the hood or trunk is open,

and bypasses those zones until it is closed.

13

Icon

The parking light icon will flash twice when armed or disarmed.

The icon also flashes during WarnAway and at the beginning and

end of remote start cycles.

Icon

The door open or trigger icon illuminates when the door trigger

has been activated or the door is open, and bypasses that zone

until it is closed.

Icon

No function.

Icon

The Valet

®

mode icon appears when the system is in Valet

®

mode.

Icon

The remote start safety shut down icon indicates the vehicle may be

in gear or other unsafe condition inhibiting remote start operation.

Icon

The battery level icon indicates the level of power remaining in

the battery.

Icon

The silent arm/disarm icon appears when the system has been

armed or disarmed in the silent mode.

Icon

The full trigger alert icon illuminates when the security system

has been triggered by a heavy impact, door trigger violation,

14

optional sensor violation, or a hood/trunk trigger.

Icon

The arm icon appears when the vehicle is armed and locked. The

disarm icon appears when the vehicle is disarmed and unlocked.

Standard LCD 2-way button functions

AAuuddiibbllee

FFuunnccttiioonn BBuuttttoonn IIccoonn IInnddiiccaattiioonn

Lamp On

(10 sec)

Power-Saver Mode*

+

Melody

Beep/Vibrate Mode

+

4 Vibrations/

1 Beep

Time Adjust for 5 Seconds 2 Beeps

Mode (hour)**

Time Adjust 1 Time***

Mode (min)**

Alarm Clock 2 Times***

Set Mode (hour)**

Alarm Clock 3 Times***

Set Mode (min)**

Alarm Clock Music 4 Times*** 5 Selections

or Power on Music 1/2/3/4/5

Selection**

Alarm Clock Adjust 5 Times***

Mode (on/off)**

Timer Count Down 6 Times***

Adjust Mode

(hour)**

Timer Count Down 7 Times***

Adjust Mode

(min)**

15

Timer Count 8 Times*** 5 Selections

Down Ending Melody 1/2/3/4/5

Selection 1**

RS Timer Count 9 Times***

Down Mode (on/off)*

Remote Start On 10 times*** 5 Selections

Melody Selection 2 1/2/3/4/5

10 Min Parking

+

1 Time Melody

Count Down Mode

20 Min Parking

+

2 Times Melody

Count Down Mode

30 Min Parking

+

3 Times Melody

Count Down Mode

60 Min Parking

+

4 Times Melody

Count Down Mode

90 Min Parking

+

5 Times Melody

Count Down Mode

120 Min Parking

+

6 Times Melody

Count Down Mode

Parking Count Down

+

7 Times Melody

Off Mode

Alarm Clock Mode

+

Melody

On/Off****

Celsius/Fahrenheit

+ +

or

Melody

Select Mode

* This function will operate in the disarmed state only.

** The button will advance the selection upward. The

button will advance the selection downward or select the off set-

ting.

*** Be sure to hold down for five seconds prior to entering

timer clock adjust mode operation.

**** Press once to have the alarm clock on. Press twice to have the

16

alarm clock off.

The remote will revert to normal operation from the set mode

when 15-seconds has elapsed without a button entry.

4-button remote standard configuration

Button

The arming is controlled by pressing this button. The panic

alarm is triggered by pressing and holding this button. Press this

button again to cancel the panic alarm.

Button

The disarming function is controlled by pressing this button.

Button

Silent Mode™ and an optional auxiliary function are controlled

by this button. (Silent Mode works by pressing this button for

less than one second before arming or disarming. An optional

auxiliary function, such as trunk release, can be controlled by

pressing and holding this button for 1.5 seconds.)

The auxiliary output controls __________________________.

➜

17

and Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and Buttons

No function.

LLCCDD 22--wwaayy rreemmoottee ooppeerraattiioonn

The remote start system operates at 434 MHz and incorporates

Directed’s proprietary A.S.K. out-board two-way transceiver. The

high frequency combined with Binary Data communication

achieves superior range with two-way communication.

system signal paging features

A page is the signal the control module sends to the transceiver as

confirmation of receipt of a command or alarm system status.

When the transceiver receives a page it will generate a page notifi-

➜

Page is loading ...

Clarion S660 User manual

Clarion S660 User manual

Related papers

Other documents