FEIN 7 1/4 in Slugger Metal Cutting Saw User manual

Brand: FEIN

Model: 7 1/4 in Slugger Metal Cutting Saw

Category: Circular saws

Type: User manual

FEIN 7 1/4 in Slugger Metal Cutting Saw: The 7 ¼" (185mm) SLUGGER METAL CUTTING SAW is designed to rapidly cut lengths or pieces of zinc coated, steel sheet metal and various metals without heating up either the blade or the material. It features a powerful motor, double insulation for safety, a laser guide for precision cutting, and a chip removal system to keep the work area clean. The cutting depth is adjustable to accommodate different material thicknesses, and the saw can be used for both straight and curved cuts.



7 ¼" (185mm) SLUGGER METAL CUTTING SAW

INSTRUCTION MANUAL

Double Insulation Slugger order number: 69908120000

Original instruction



TABLE OF CONTENTS

Safety Rule 2

Additional safety rules for metal cutting saw 6

Assembly and adjustment instruction 8

Installing a new saw blade 8

Laser 10

Cutting depth adjustment 11

Operation 11

Guide ruler 12

Chip removal 13

Replacing carbon brushes 13

Maintenance and servicing 14

Trouble shooting 14

Specifications 14

Parts diagram 16

Replacement parts 17

Manufacturer 20

Intended use

The metal cutting saw is powerful enough to cut steel sheet metal as thick as ¼” (6mm). Metal cutting

saws are designed to rapidly cut lengths or pieces of zinc coated, steel sheet metal and various

metals without heating up either the blade or the material.

WARNING: To reduce the risk of injury, read the instruction manual.

WARNING! Read all safety warnings and all instructions Failure to follow the warnings and

instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use



any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed (grounded) surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase

the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter

(GFI) protected supply. Use of GFI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before connecting

to power source and/ or battery pack, picking up or carrying the tool. Carrying power tools

with your finger on the switch or energizing power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving

parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the tool before



making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

h) Caution! The dust collect cover is very hot when cutting or after cutting.

Don’t touch it by hand!!

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Safety Instructions for Saw

DANGER:

a) Keep hands away from cutting area and the blade. Keep your second hand on auxiliary

handle. If both hands are holding the saw, they cannot be cut by the blade.

b) Do not reach underneath the workpiece. The guard cannot protect you from the blade below

the workpiece.

c) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the

blade teeth should be visible below the workpiece.

d) Never hold piece being cut in your hands or across your leg. Secure the workpiece to a

stable platform. It is important to support the work properly to minimize body exposure, blade

binding, or loss of control.

e) Hold power tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also

make exposed metal parts of the power tool "live" and shock the operator.

f) When ripping always use a rip fence or straight edge guide. This improves the accuracy of

cut and reduces the chance of blade binding.

g) Always use blades with correct size and shape (diamond versus round) of arbor holes.

Blades that do not match the mounting hardware of the saw will run ineffectively, causing loss

of control.

h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were

specially designed for your saw, for optimum performance and safety of operation.



Causes and Operator Prevention of Kickback:

 Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the workpiece toward the operator.

 When the blade is pinched or bound tightly by the cut closing down, the blade stalls and the motor

reaction drives the unit rapidly back toward the operator.

 If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can

dig into the top surface of the metal, causing the blade to climb out of the cut and jump back

toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below:

a) Maintain a firm grip with both hands on the saw and position your arms to resist

kickback forces. Position your body to either side of the blade, but not in line with the

blade. Kickback could cause the saw to jump backwards, but kickback forces can be controlled

by the operator if proper precautions are taken.

b) When blade is binding or when interrupting a cut for any reason, release the trigger and

hold the saw motionless in the material until the blade comes to a complete stop. Never

attempt to remove the saw from the work or pull the saw backward while the blade is in

motion or kickback may occur. Investigate and take corrective actions to eliminate the cause

of blade binding.

c) When restarting a saw in the workpiece, center the saw blade in the cut and check that

saw teeth are not engaged into the material. If saw blade is binding, it may walk up or

kickback from the workpiece as the saw is restarted.

d) Support large panels to minimize the risk of blade pinching and kickback. Large panels

tend to sag under their own weight. Supports must be placed under the panel on both sides

near the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow

cut causing excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be tight and secure before making

cut. If blade adjustment shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making “plunge cuts” into existing walls or other blind areas.

The protruding blade may cut objects that can cause kickback.

Lower Guard Safety Instructions

a) Check lower guard for proper closing before each use. Do not operate the saw if lower

guard does not move freely and closes instantly. Never clamp or tie the lower guard into

the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower

guard with the retracting handle and make sure it moves freely and does not touch the blade or

any other part in all angles and depths of cut.

b) Check the operation of the lower guard spring. If the guard and the spring are not

operating properly, they must be serviced before use. Lower guard may operate sluggishly

due to damaged parts, gummy deposits, or a build-up of debris.



c) Lower guard manually only for special cuts such as “plunge cuts” and “compound cuts.”

Raise lower guard by retracting handle as soon as blade enters the material, the lowerguard

must be released. For all other sawing, the lower guard should operate automatically.

d) Always observe that the lower guard is covering the blade before placing saw down on

bench or floor. An unprotected coasting blade will cause the saw to walk backwards cutting

whatever is in its path. Be aware of the time it takes for the blade to stop after switch is

released.

Additional Safety Instructions

 Use clamps or another practical way to secure and support the workpiece to a stable platform.

Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

 Keep your body positioned to either side of the blade, but not in line with the saw blade.

KICKBACK could cause the saw to jump backwards (see Causes and Operator Prevention of

KICKBACK).

 Avoid cutting nails. Inspect and remove all nails from lumber before cutting.

 Always make sure nothing interferes with the movement of the lower blade guard.

 Accessories must be rated for at least the speed recommended on the tool warning label. Wheels

and other accessories running over rated speed can fly apart and injure. Accessory ratings must

always be above tool speed as shown on tool nameplate.

 Always make sure the saw is clean before using.

 Stop using this saw and have it properly serviced if any unusual noise or abnormal operation

occcurs.

 Always be sure all components are mounted properly and securely before using tool.

 Always handle the saw blade with care when mounting or removing it or when removing the

diamond knockout.

 Always wait until the motor has reached full speed before starting a cut.

 Always keep handles dry, clean and free of oil and grease. Hold the tool firmly with both hands

when in use.

 Always be alert at all times, especially during repetitive monotonous operations. Always be sure

of position of your hands relative to the blade.

 Stay clear of end pieces that may fall after cutting off. They may be hot, sharp and/or heavy.

Serious personal injury may result.

 Replace or repair damaged cords. Make sure your extension cord is in good condition. Use only

3-wire extension cords that have 3-prong grounding-type plugs and 3-pole receptacles that

accept the tools plug.



ADDITIONAL SAFETY RULES OF

METAL CUTTING SAW

CAREFULLY READ THE FOLLOWING SAFETY WARNINGS PRIOR TO CONNECTING THE

METAL CUTTING SAW TO POWER.

1. Must keep the safety cover in the fixed position, never wedging or binding the safety cover. Before

using the metal cutting saw, please ensure the safety cover moves freely and closes instantly.

Don’t force the operation.

Caution: If the saw is accidentally dropped, the cover could be damaged.

2. The blade should be kept clean and sharp. Breakdown and rebound can be lowered to the

minimum limitation with the blade sharp.

3. Danger: The hand must depart from the sawing area when tool works. Don’t touch the blade when

blade is rotating, and don’t put the workpiece in. Don’t take the process-workpiece sawed by hand

when blade is still rotating.

Caution: The blade will rotate a period of time after turning off the switch.

4. Adjustment. Before sawing, ascertain the adjustment of saw depth is right.

5. Must select the right blade. Use the suitable saw blade within the range shown on nameplate.

6. Guide cord should be apart from sawing place and be fixed when sawing, and ensure it can not be

twined by work-piece when sawing. The tool must be held steadily when sawing, and use the

appropriate work-piece to support, and put the guide cord far away from the work-piece.

7. Do not use cutting oil while cutting.

8. Do not use blades which are deformed or cracked.

9. Always use safety glasses. Everyday eyeglasses only have impact resistant lenses; they are not

safety glasses.

10. To avoid possible hearing damage, wear ear plugs when using power tool.

Motor Specifications and Electrical Requirements

Power Supply and Motor Specifications

The AC motor used in this saw is a universal. Nonreversible type having the following specifications:

Model No.

69908120000

Maximum

Developed H.P

1.9

Voltage

120

Amps

Hertz (Cycles)

Phase

Single

RPM

3800

Power Connections

A separate electrical circuit should be used for your tools. This circuit should not be less #12 wire and



should be protected with a 20 Amp fuse. Have a certified electrician replace or repair a worn cord

immediately and connectthe motor as nameplate mentions. Running low voltage will damage the

motor.

WARNING: DO NOT EXPOSE THE TOOL TO RAIN OR OPERATE IN DAMP CONDITIONS.

ASSEMBLY AND ADJUSTMENT INSTRUCTIONS

WARNING:

For your own safety, never connect the plug to a power source outlet until all assembly steps are

complete and you have read and understood the safety and operating instructions. The safety

cover is attached to the saw for your protection. Should the safety cover become damaged, do not

use the saw until damaged cover has been replaced. If the safety cover becomes dirty, or chip

adheres to it, clean the safety cover carefully with a damp cloth.

Installing a new saw blade

WARNING: To prevent an accident or personal injury, always turn off the trigger switch and

disconnect the power plug from the receptacle before removing or installing a blade. Only use

blades designed for metal cutting saws. The use of any abrasive wheels, alternative purpose

wheels or different size blades could void the warranty. Check regularly that the blade is flat, sharp

and free of any defect or damage. Ensure the saw is disconnected from power.

1. Change blade: Loosen the lock bolt counterclockwise

(A) then take off chip shield assembly. Refer to Fig.1

2. Take out HEX wrench (A)

The size for HEX wrench is M6 (B). Refer to Fig.2



3. Push down the safety lever to lock the motor shaft.

4. Use the HEX wrench to loosen the shaft screw

(counterclockwise) then remove the shaft screw and

flange. Refer to Fig.3

5. Open the blade guard (A), ensure inner flange is installed,

install blade and check for proper rotation (B). Refer to

Fig.4

5.1 Mount chip shield assembly on metal saw housing

and tighten lock bolt (B). Refer to Fig.1

6. Place outer flange and bolt through center blade hole

and use hex wrench to tighten (B) while pushing safety

lock lever to lock motor shaft (A). Refer to Fig.5

Usage for bevel

1. Loosen the locking handle (A), move the base along

the angle plate from 0 ﾟ to 45 ﾟ(B) (or the degree that

you want), then tighten the locking handle. Refer to Fig.6



LASER

The usage of laser

1. When the saw is plugged in, turn on the laser switch.

Laser is displayed as (B) in Fig.7. The laser is a cutting guide

only.

2. Laser indication is set according to the saws angle degree.

It asists in cutting the angle.

For example:

Saws angle indicates at 0 ﾟ and laser will be 0 ﾟ(B),

Saws angle indicates at 45 ﾟ(C) Laser will be 45 ﾟ(D)

Refer to Fig.8

ALIGNING THE LASER GUIDE LINE

DANGER:Laser radiation. Avoid direct eye contact with light source.

WARNING: Use of controls, adjustments, or performance of procedures other than those specified,

may result in hazardous radiation exposures. When you adjust the laser, do not turn on the switch.

Fig.9 Accidental starting could occur.

1. 0∘line adjustment is done by tightenening and loosening of HEX screw on laser with

M2 HEX wrench (A) as Fig.10. This adjustment moves the laser side to side.

2. Adjust laser orientation by using a flat blade screwdriver on the front of the lense. (B) Fig.10.



3. Fig 11 Fig.12

Fig.10



CUTTING DEPTH ADJUSTMENT

1. Pull up & loosen the lock lever (A) first. Refer to Fig.13

2. Lift the back of the saw away from the baseplate

until the approximate depth is achieved.

3. Ensure the lock lever (A) Fig.14 is tightened securely

after the depth adjustment is made.

3.1 To adjust the lock and unlock positions (if necessary),

simply pull the lever towards the hand-grip of the saw

and rotate it slightly as required.

Warning:Cutting with a loose lock lever causes injury.

OPERATION

Operation of Switch

Press the stop button (A) first and pull the

trigger (B) at the same time to turn on saw.

To turn off saw, release trigger. Refer to Fig.15



Operation

Use right hand to hold the trigger handle (A), and

left hand to hold the front handle (B). When the blade

reaches the maximum speed rate, push the saw forward

along the surface of workpiece. Keep the saw moving

smoothly until the cut is finished. Refer to Fig.16

DIRECTION OF SAWING

Align saw blade to the right of the operator.

THE GUIDE RULER

The guide ruler can be used to cut a straight sawing line

along the workpiece and can be affixed at the front of

base with wing nut. The guide ruler (A) can be used on

the right side of the blade only, shown Fig.17. Using the

guide provides accurate cuts compared to free-hand

cutting. Locate the guide into the mounting slots at the

front of the baseplate and tighten the wing screw to lock

it at the desired cut width.

SIGHTING NOTCH FOR FREE-HAND CUTTING

Sighting notchtes (A) near the front of the baseplate provides guidance. When performing

free-hand cutting (at 90 degrees) the cutting line for the saw blade can be observed through a

u-shaped sighted notch at the front of the base plate.

Align the cutting line on the workpiece with the v-shaped

sighting notch at the front of the base plate when

cutting at 45 degree angle. (This is due to the placement

of the pivot point).

Turn saw on before contacting workpiece, wait until the

blade reaches full RPM before proceeding with cut. Apply

even pressure all of the way through cut to ensure proper

blade operation and to obtain smoother cutting.



Beware:Beware of the kickback at the instant the running blade touches the workpiece.

CHIP REMOVAL

GLASS WINDOW

The chips can be observed through a glass window. When the chip shield area is half full, remove

the cover by loosening the two bolts and empty the contents. Make sure the chips have been

removed completely.

Way to clean the cutting chips

1. Unscrew the two bolts (A) on the blade housing. Refer to Fig.19

2. Remove chip shield (B). (keeping the bolts screwed on guard.) Refer to Fig.20

3. Remove the chips.

Beware: Always keep the saw away from your body when removing the chip shield, the chips will

fall out. The chips could be very hot, be careful not to touch them when you remove the chip

shield.

REPLACING CARBON BRUSHES

► Caution: Turn off the switch and disconnect plug from power supply before checking.

REPLACE CARBON BRUSHES

Check brushes regularly, if worn down to 1/4” (6mm), replace

brushes. Carbon brushes should be clean and slide freely in

holder. Carbon brushes should be replaced in pairs. Use a

flat blade screwdriver to remove the brush cap (A), take out

the worn carbon brush (B) insert new carbon brush and

secure the brush holder cap. Refer to Fig.21



MAINTENANCE AND SERVICING

Disconnect tool from power supply before carrying out any servicing and maintenance. Keep the

machine clean. Never use a saw blade that is damaged or distorted. Replace the saw blade when it

becomes dull. For service and replacement pieces see the replacement parts list and manufacturer

website. Inspect the safety cover to assure that it is in good condition and moves smoothly. Never use

the tool unless the safety cover operates properly and it is in good operating condition. After operation

of the tool has been completed, make sure power plug has been disconnected from the receptacle

and store it in a secure place out of the reach of children. Periodically remove chips in the chip cover

and dust from the surface of the power tool with a damp cloth. Keep the tool from contact with water or

oil.

TROUBLESHOOTING

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

• Saw won’t start • Loss of power supply • Check power source

• Brushes worn or sticking • Check brushes

• Switch is faulty • Contact repair center

• Possible short circuit • Contact repair center

• Cord damaged • Contact repair center

• Unsatisfactory cuts • Dull, damaged or incorrect blade • Sharpen or replace blade

• Motor is overloaded. • Reduce pushing force

• Unusual sound • Mechanical obstruction. • Contact repair center

• Possible short circuit • Contact repair center

• Blade out of balance • Replace blade

• Heavy sparking inside

motor housing

• Brush not moving freely • Disconnect power, remove

brushes and clean or replace

• Possible short circuit/dirty

commutator

• Contact repair center

SPECIFICATONS:

Rated voltage 120V~ 50/60Hz

Rated input 1400W

No load speed 3800RPM

Arbor ¾” (20.0 mm)

Saw blade diameter 7-1/4" (185mm)

Arm-held vibration 7.20m/s2

Weight 15 lbs. (6.8kg)

Max. cutting depth at 90 ﾟ

2 7/16” (62mm)



Max. cutting depth at 45 ﾟ

1 9/16” (40mm)

Max. cutting thickness ¼” (6mm)

Sound power level 98dB(A)

Sound pressure level 88dB(A)



REPLACEMENT PARTS

REF NO. SLUGGER ORDER NUMBER DESCRIPTION

1 69908120166 LOCKBOLT

2 69908120167 OUTERCOVER

3 69908120004 GLASS

4 69908120169 CHIPSHIELD

5 69908120170 SELFTA PPINGSCREW

6 69908120171 GUARD

7 69908120172 FLATHDSCREW

8 69908120173 TABLEINSERT

9 69908120174 PANHDSCREW

10 69908120175 BLADEHOUSING

12 69908120176 CUSHION

13 69908120177 FLATWASHER

14 69908120178 PANHDSCREW+WASHER

15 69908120179 LEFTPLATE

16 69908120172 FLATHDSCREW

17 69908120181 CARRIAGESCREW

18 69908120182 FLATWASHER

19 69908120183 WAVEWASHER

20 69908120184 SECURELEVER

21 69908120185 E‐RING(ETW)

22 69908120186 SPECIALSCREW

24 69908120158 SETSCREW

25 69908120188 GRASPHANDLE

26 69908120178 PANHDSCREW+WASHER

27 69908120190 COVER

28 69908120191 CROSSRECESSEDTRUSSHEADSCREW

29 69908120192 JACKSHAFTASSEMBLY

30 69908120193 STEELPLATE

31 69908120194 FLATHDSCREW

32 69908120195 SAFETYCOVER

33 69908120196 RETURNSPRING

34 69908120197 FRONTPLATE

35 69908120172 FLATHDSCREW

36 69908120199 INSIDEBLADEFLANGE

38 69908120201 OUTERFLANGE

39 69908120012 ARBORBOLT(BladeBolt)

40 69908120130 CORDGUARD



41+50 69908120274 COMPLETEHANDLE

42 69908120205 POWERCORD

43 69908120206 SWITCH

43.1 69908120207 PANHDSCREW

44 69908120208 LOCKBUTTON

45 69908120135 SPRING

46 69908120210 SELFTA PPINGSCREW

47 69908120211 JUMPERWIRE

49 69908120153 CORDCLAMP

51 69908120214 SELFTA PPINGSCREW

52 69908120178 PANHDSCREW+WASHER

53 69908120216 GUIDERULER

54 69908120217 BASEPLATE

55 69908120111 SPRINGSHAFTLOCKBUTTON

56 69908120099 WINGSCREW

57 69908120220 SOCKETSCREW

58 69908120221 OILSEAL

60 69908120222 BAFFLE

61 69908120223 SPRING

62 69908120224 STOPLEVER

63 69908120225 BALLBEARING

64 69908120226 ARMATUREASS'YWITHBEARINGSET

65 69908120227 INSULATIONRING

66 69908120228 BALLBEARING

67 69908120229 PANHDSELF‐TAPSCREW/WASHER

68 69908120230 FIELDASSEMBLY

69 69908120231 MOTORHOUSING

70 69908120095 SCREWPANHEADM5+WASHER

71 69908120233 SETSCREW

72 69908120234 BRUSHHOLDER

73 69908120235 BRUSH

74 69908120236 BRUSHCAP

75 69908120237 JUMPERWIREA

78 69908120238 COVER

79 69908120239 TERMINALBLOCK

80 69908120240 EXTRUDEDTUBING

81 69908120241 FERRITECORE

82 69908120242 WRENCHHOLDER

83 69908120161 6MMHEXWRENCH

84 69908120244 PANHDSCREW



85 69908120245 SELFTA PPINGSCREW

86 69908120156 SELFTA PPINGSCREW

87 69908120247 LASERCOVER

90 69908120250 ACTODCTRANSFORMERMODULE

91 69908120251 LASERBUTTON

92 69908120252 BUTTONSWITCHASSEMBLY

93 69908120135 SPRING

94 69908120254 LASER

95 69908120144 O‐TYPERING

96 69908120143 LASERFIXEDRING

97 69908120257 HEIGHTADJUSTBRACKET

98 69908120098 RIVET

99 69908120259 LOCKERSUPPORT

100 69908120260 NYLONNUT

102 69908120098 RIVET

103 69908120262 FLATHDSCREW

104 69908120114 LOCKLEVER

105 69908120264 BEVELTRUNNION

106 69908120265 SPECIALNUT

107 69908120266 CARRIAGESCREW

108 69908120267 FLATWASHER

109 69908120268 SPACERRING

111 69908120269 FLATWASHER

112 69908120270 RIGHTPLATE

113 69908120244 PANHDSCREW

901 69908120272 AIRBLOWINGCASE



Please read the instructions carefully before starting the machine.

Wear ear protection!

Always wear safety glasses when using the machine.



Always keep hands away from the path of the saw blade.



Always disconnect the plug from the socket before carrying out any work on the machine.



Never expose tool to rain.



Caution



Laser radiation. Avoid direct eye contact with light source.



Caution:When cutting don’t touch the metal parts to avoid burns.



Do not dispose of electric tools with household waste material!

Caution: Laser radiation - don’t stare into beam.

FEIN Power Tools, Inc., 1030 Alcon Street, Pittsburgh, PA 15220

Tel. 412-922-8886, Toll Free: 1-800-441-9878, www.feinus.com

FEIN 7 1/4 in Slugger Metal Cutting Saw User manual

Brand: FEIN

Model: 7 1/4 in Slugger Metal Cutting Saw

Category: Circular saws

Type: User manual

Download PDF

report

FEIN 7 1/4 in Slugger Metal Cutting Saw User manual

FEIN 7 1/4 in Slugger Metal Cutting Saw User manual

Related papers

Other documents