Goldstar MA-972MW is a microwave oven with 1000 Watts of power and 13.5 Amps of current, featuring a 2M246 magnetron and a 0-99 minute 99 second digital timer. It offers variable cooking power levels, ranging from full power to simmer and warm, and includes a defrost function. With its 20-inch width, 11.75-inch height, and 14.75-inch depth, it accommodates a 13.25 x 8 x 14.5-inch oven cavity and a glass turntable. It also includes an owner's manual and a cooking guide for user convenience.
Goldstar MA-972MW is a microwave oven with 1000 Watts of power and 13.5 Amps of current, featuring a 2M246 magnetron and a 0-99 minute 99 second digital timer. It offers variable cooking power levels, ranging from full power to simmer and warm, and includes a defrost function. With its 20-inch width, 11.75-inch height, and 14.75-inch depth, it accommodates a 13.25 x 8 x 14.5-inch oven cavity and a glass turntable. It also includes an owner's manual and a cooking guide for user convenience.
MICROWAVE OVEN
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT, READ THE
SAFETY PRECAUTIONS IN THIS MANUAL.
MODEL: MA-972M
MA-972MW
SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be
taken to avoid possible exposure to excessive microwave energy.
PRECAUTIONS TO BE OBSERVED BEFORE
AND DURING SERVICING TO AVOID
POSSIBLE EXPOSURE TO EXCESSIVE
MICROWAVE ENERGY
A) Do not operate or allow the oven to be operated with the door open.
B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary; (1) Interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
C) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation
and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.
E) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
TABLE OF CONTENTS
(Page)
SAFETY PRECAUTIONS
-----------------------------------------------------------------------------------
Inside front cover
SPECIFICATIONS
------------------------------------------------------------------------------------------------------------------
1-1
CAUTIONS
----------------------------------------------------------------------------------------------------------------------------
2-1
INSTALLATIONS
-------------------------------------------------------------------------------------------------------------------
3-1
OPERATING INSTRUCTIONS
-------------------------------------------------------------------------------------------------
4-1
FEATURES
-----------------------------------------------------------------------------------------------------------------------
4-1
CONTROL PANEL
-------------------------------------------------------------------------------------------------------------
4-1
OPERATING SEQUENCE
---------------------------------------------------------------------------------------------------
4-2
SCHEMATIC DIAGRAM
------------------------------------------------------------------------------------------------------
4-3
CIRCUIT DESCRIPTION
-----------------------------------------------------------------------------------------------------
4-4
SERVICE INFORMATION
-------------------------------------------------------------------------------------------------------
5-1
TOOLS AND MEASURING INSTRUMENTS
--------------------------------------------------------------------------
5-1
MICROWAVE LEAKAGE TEST
--------------------------------------------------------------------------------------------
5-1
MEASUREMENT OF MICROWAVE POWER OUTPUT
-----------------------------------------------------------
5-3
DISASSEMBLY AND ADJUSTMENT
------------------------------------------------------------------------------------
5-3
INTERLOCK CONTINUITY TEST
-----------------------------------------------------------------------------------------
5-7
COMPONENT TEST PROCEDURE
--------------------------------------------------------------------------------------
5-8
TROUBLE SHOOTING
-----------------------------------------------------------------------------------------------------
5-11
EXPLODED VIEW
------------------------------------------------------------------------------------------------------------------
6-1
REPLACEMENT PARTS LIST
-------------------------------------------------------------------------------------------------
7-1
SCHEMATIC DIAGRAM OF P.C.B.
-------------------------------------------------------------------------------------------
8-1
PRINTED CIRCUIT BOARD
------------------------------------------------------------------------------------------------
8-2
P.C.B. PARTS LIST
----------------------------------------------------------------------------------------------------------------
9-1
SPECIFICATION
1-1
This microwave oven is designed for household use only.
It is not recommended for commercial purpose.
ITEM
MODEL
Power Requirement
Power Output
Microwave Frequency
Magnetron
Timer
Outside Dimensions
Cavity Dimensions
Net Weight
Shipping weight
Control Complement
Nameplate Location
Accessories
DESCRIPTIONS
MA-972M, MA-972MW
120 V AC, 60Hz
1,500 W (13.5A)
Single phase, 3 wire grounded
1000 Watts full microwave power (IEC705)
2,450MHz
2M246
0 - 99min. 99sec.
20"(W) x 11
3
/4"(H) x 14
3
/4"(D)
13
1
/4"(W) x 8"(H) x 14
1
/2"(D)
38 lbs (approx.)
41 lbs (approx.)
Touch Control System
Clock : 1:00 - 12:59
Microwave Power for Variable Cooking
Power level
HIGH
-------------------------------
Full power throughout the cooking time
9(Sauté)
------
approx. 90% of Full power, 8(Reheat)
--------
approx. 80%
7(Med.-High)
--------------
approx. 70%, 6(Medium)
--------
approx. 60%
5(Med.-Low)
---------------
approx. 50%, 4(Defrost)
---------
approx. 40%
3(Low)
--------------------
approx. 30%, 2(Simmer)
---------
approx. 20%
1(Warm)
------------------
approx. 10%
Owner's manual & cooking guide
Glass turntable
Rotating ring
Back Side
• DO NOT operate on a 2-wire extension cord during
repair and use.
• NEVER TOUCH any oven components or wiring during
operation.
• BEFORE TOUCHING any parts of the oven, always
remove the power plug from the outlet.
• For about 30 seconds after the oven stops, an electric
charge remains in the high voltage capacitor. When
replacing or checking, you must be discharge the high
voltage capacitor by shorting across the two terminals
with an insulated screwdriver.
•
Remove your watches
whenever working close to or replacing the Magnetron.
• DO NOT touch any parts of the control panel circuit. A
resulting static electric discharge may damage this
P.C.B.
• NEVER operate the oven with no load.
• NEVER injure the door seal and front plate of the oven
cavity.
• NEVER put iron tools on the magnetron.
• NEVER put anything into the latch hole and the
interlock switches area.
• Proper operation of the microwave oven requires that
the magnetron be assembled to the waveguide and
cavity. Never operate the magnetron unless it is
properly installed.
• Be sure that the magnetron gasket is properly
installed around the dome of the tube whenever
installing the magnetron.
2-1
CAUTIONS
Unlike other appliances, the microwave oven is
high-voltage and high-current equipment.
Though it is free from danger in ordinary use,
extreme care should be taken during repair.
THE OVEN IS TO BE SERVICED ONLY
BY PROPERLY QUALIFIED SERVICE
PERSONNEL.
MICROWAVE RADIATION
Personnel should not be exposed to the
microwave energy which may radiate from the
magnetron or other microwave generating
device if it is improperly used or connection.
All input and output microwave connections,
waveguide, flange, and gasket must be secure
never operate the device without a microwave
energy absorbing load attached.
Never look into an open waveguide or antenna
while the device is energized.
Gasket
ANTENNA
COOLING FIN
MAGNETRON
CHASSIS GROUND
FILAMENT
TERMINALS
MAGNETRON
3-1
Installing microwave oven
1. Empty the microwave oven and clean inside it with
a soft, damp cloth. Check for damage such as
misaligned door, damage around the door or dents
inside the cavity or on the exterior.
2. Put the oven on a counter, table or shelf that is
strong enough to hold the oven and the food and
utensils you put in it.(The control panel side of the
oven is the heavy side. Use care when handling.)
3. Do not block the vent and the air intake openings.
Blocking vent or air intake openings can cause
damage to the oven and poor cooking results.
Make sure the microwave oven legs are in place to
ensure proper air flow.
4. The oven should not installed in any area where
heat and steam are generated, because they may
damage the electronic or mechanical parts of the
unit.
Do not install the oven next to a conventional
surface unit or above a conventional wall oven.
5. Use microwave oven in an ambient temperature
less than 104°F(40°C).
6. Place the microwave oven on a sturdy and flat
surface, at least 10 Cm(4 inches) from the wall.
7. Place the microwave oven as far away as possible
from TV, RADIO, COMPUTER, etc., to prevent
interference.
Grounding Instructions
For personal safety, this appliance must be fully
grounded at all times.
In the event of an electrical short circuit, grounding
reduces the risk of electrical shock.
The plug must be plugged into an outlet that is
properly installed and grounded.
INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
10cm
WARNING
Improper use of the grounding plug can result in a
risk of electric shock.
Do not, under any circumstances, cut or remove
the third ground prong from the power cord plug.
PREFERRED METHOD
INSURE PROPER GROUND
EXISTS BEFORE USE
TEMPORARY METHOD
(ADAPTER PLUGS ARE NOT
PERMITTED IN CANADA)
ALIGN LARGE PRONGS/SLOTS
INSURE PROPER GROUND AND
FIRM CONNECTION BEFORE USE
Features
Control Panel
1. INDICATORS
2. ONE TOUCH CONTROL : Used to cook the foods
listed by one touch.
3. INTERNATIONAL FOODS
4. TIME : Used these pads to set the cooking time.
5. CLOCK : Use to set the time of day.
6. STOP/CLEAR :Used to stop oven and clear all
entries except time of day.
7. DISPLAY WINDOW
8. AUTO WEIGHT DEFROST : Used to select the
desired auto weight defrost programmed with weight
pad.
9. POWER : Used in selected the desired power level
for cooking.
10. EZ on : Used to set quickly and start without the
need to touch START.
11. NUMBER: Used to set for Time of day, Cooking time,
Power level or Defrost weight.
12. HOLD WARM : Used to keep the food warm after
the cooking is done.
13. START : One tap allows oven to begin functioning.
14. DOOR OPEN BUTTON : Press to open the door.
Opening the door during cooking will stop the oven.
4-1
OPERATING INSTRUCTIONS
Oven Front Plate
Window Door Screen
Door Seal
Display Window
Control Panel
Door Open Button
Safety Door Lock System
Turntable
Rotating Ring
1.
2.
3.
MEAT
POULTRY
FISH
AUTO WEIGHT
DEFROST
STOP/CLEAR
1
7
8
9
10
11
12
13
14
2
123
456
78
0
9
3
4
5
6
HOLD
WARM
START
CLOCK
PLATE OF
FOOD
POPCORN
ENTREES
ITALIAN SPANISH ORIENTAL
DINNERS
TIME POWER
EZ on
POTATO
ONE TOUCH
INTERNATIONAL FOODS
Operating Sequence
The followings are description of component functions
during oven operation.
1. Setting the clock
ex) To set 4:30, touch number key [4],[3], and [0].
NOTE: 1) This is a 12 hour clock.
2) Clock will operate as long as power is
applied to the oven.
2. Cancel function
Touch the pad whenever you need to
cancel an entry or a function currently is use.
The display will either return to the last item entered,
or return to the clock.
3. Child lock
This oven has a CHILD LOCK feature.
TO SET CHILD LOCK
Touch the pad.
• Touch and hold "0" pad "LOCK" appear on
the display.
You can't input any key except "0" key.
TO CANCEL CHILD LOCK
Touch the pad.
• Touch and hold "0" pad "LOCK" disappears.
4. Time Cooking
5. Multi Stage Cooking
6. Auto Weight Defrost
7. One Touch & International Foods
Cooking
NOTE : Heat only 1 package at a time.
4-2
STOP/CLEAR
CLOCK
STOP/CLEAR
TIME
START
TIME
NUMBER
POWER
POWER
NUMBER
NUMBER
NUMBER
STOP/CLEAR POPCORN
NUMBER
STOP/CLEAR
TIME
NUMBER
NUMBER
START
POWER
STOP/CLEAR
STOP/CLEAR
STOP/CLEAR
1st stage
2nd stage
CLOCK
STOP/CLEAR
AUTO
WEIGHT
DEFROST
1, 2 or 3
WEIGHT IN
POUNDS,
OUNCES
START
SCHEMATIC DIAGRAM
4-3
AC 120V
60Hz
FUSE
20A
L
N
GN
MICOM CONTROLLER
THERMOSTAT
BK BN
RD
RD
WH
F.M
T.T.M
WH
YL
MAGNETRON
RD
RD
FFA
H.V.
CAPACITOR
H.V. DIODE
RD
BK
BK
PK
PK
GN
BK
1
3
1
3
5
WHWH
OVEN
LAMP
FAN
MOTOR
TURNTABLE
MOTOR
O.L
TRANSFORMER
H.V.
PRIMARY
SWITCH
SECONDARY
SWITCH
MONITOR
SWITCH
NOTE : DOOR IS OPENED.
BN : BROWN BL : BLUE YL : YELLOW PK : PINK
RD : RED BK : BLACK WH : WHITE
CN.2
CN.1
PT.1
RY.1
RY.2
WH
WH
BL
IMPORTANT SAFETY NOTE: THE SHADED AREA ON THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL FEATURES
IMPORTANT FOR PROTECTION FROM MICROWAVE RADIATION, FIRE, AND ELECTRICAL SHOCK
HAZARDS. WHEN SERVICING, IT IS ESSENTIAL THAT ONLY MANUFACTURERS SPECIFIED PARTS
BE USED FOR THE CRITICAL COMPONENTS IN THE SHADED AREAS OF THE SCHEMATIC DIAGRAM.
NOTICE: SINCE THIS IS BASIC SCHEMATIC DIAGRAM, THE VALUES OF COMPONENTS AND
SOME PARTIAL CONNECTIONS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
MICROWAVE OVEN
Circuit Description
• The low voltage transformer supplies the necessary
voltage to the micom controller when power cord is
plugged in.
• When door is closed, the primary switch is ON, the
secondary switch is ON, and the monitor switch is
connect the main line(contact COM and NO).
WHEN COOKING POWER LEVEL AND
COOKING TIME SET BY SELECTING
• The micom controller memorizes the function you set.
• The time you set appears in the display window.
• Each indicator light turns on to indicate that the stage
has been set.
WHEN TOUCHING THE START PAD
• The coil of the relay is energized by micom controller.
• Power input is supplied to the high voltage transformer
through the primary switch, relay 2 and monitor switch.
• Turntable rotates.
• The fan motor rotates and cools the magnetron by
blowing the air (coming from the intake on the
backplate) over the magnetron.
• The air is also directed into the oven to exhaust the
vapor in the oven through the upper plate.
• Cooking time starts counting down.
• 3.2 volts AC is generated from the filament winding of
the high voltage transformer. This 3.2 volts is applied to
the magnetron to heat the magnetron filament through
two noise-preventing choke coils.
A high voltage of approximately 2100 volts AC is
generated in the secondary of the high voltage
transformer which is increased by the action of the high
voltage diode and charging of the high voltage
capacitor.
• The negative 4,000 Volts DC is applied to the filament
of the magnetron.
WHEN THE OVEN IS SET AT ANY LEVEL
EXCEPT MAXIMUM.
• The micom controller controls the ON-OFF time of
relay 2 by the applied signal to vary the average output
power of microwave oven as POWER LEVEL.
(refer to page 1-1)
• One complete cycle of relay 2 is 22 seconds.
WHEN THE DOOR IS OPENED DURING
COOKING
• Both primary switch and relay 2 will cut off primary
winding voltage of the high voltage transformer.
• ON-OFF of relay 2 is coupled electrically with opening
and closing of secondary switch.
• When the door is opened, secondary switch is opened
and when the door is closed, secondary switch is
closed.
• The cooking time stops counting down.
• Relay stops functioning.
• As the door is opened, if the contact of primary switch
fails to open, the fuse opens due to the large current
surge caused by the monitor switch activation which, in
turn, stops magnetron oscillation.
4-4
L
FUSE
H.V.
TRANS-
FORMER
RELAY2
MICOM CONTROLLER
SECONDARY
SWITCH
PRIMARY
SWITCH
MONITOR
SWITCH
N
L
FUSE
RELAY2
MICOM CONTROLLER
SECONDARY
SWITCH
PRIMARY
SWITCH
MONITOR
SWITCH
H.V.
TRANS-
FORMER
N
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Goldstar MA-972MW is a microwave oven with 1000 Watts of power and 13.5 Amps of current, featuring a 2M246 magnetron and a 0-99 minute 99 second digital timer. It offers variable cooking power levels, ranging from full power to simmer and warm, and includes a defrost function. With its 20-inch width, 11.75-inch height, and 14.75-inch depth, it accommodates a 13.25 x 8 x 14.5-inch oven cavity and a glass turntable. It also includes an owner's manual and a cooking guide for user convenience.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Goldstar MA-1103W Owner's manual
-
-
-
-
-
LG GMS-1121TW Owner's manual
-
-
-
-