Kathrein UFS 913sw Operating Instructions Manual

Operating instructions – Part 2 UFS 913

Basic functions and operation English

Receivers Part no. Operating manual valid as of software version:

UFS 913si 20210184

1.00

UFS 913sw 20210185

2

Dear customer,

this operating manual are intended to help you make the fullest use of the extensive range of functions

offered by your new receiver.

We have tried to make the operating instructions as easy as possible to understand, and to keep them

as concise as possible. To help you understand particular specialist terms that cannot be translated,

we have added a short glossary at the end of the manual.

The power switch is an environmentally friendly feature. If you will not be using your receiver for an

extended period, you should use the on/off switch to disconnect it from the power supply and save energy.

For shorter breaks, you can use the remote control to switch the receiver to standby, which uses only

a minimal amount of energy.

We hope your reception will always be brilliant and you will enjoy using your new HDTV receiver.

Your

KATHREIN team

Preface

3

Information on Audio MPEG Inc. and S.I.SV.EL, S.P.A:

This unit makes use of legally protected technologies, which are protected by patents in the USA and also

by other intellectual property rights in other countries.

KATHREIN-Werke KG has obtained licences from Audio MPEG Inc. and Societa‘ Italiana per lo sviluppo

dell‘elettronica, S.I.SV.EL, S.P.A to use these technologies. These licences carry certain restrictions, which

apply also to you as the customer. Accordingly this unit may only be used by the end customer for private

non-commercial purposes and for the licensed content. It may not be used for commercial purposes. The

use of products or processes that are sold or used with this unit is not included in this statement. The use of

reverse engineering is not permitted in respect of the licensed technologies, nor is disassembly.

Note on DiSEqC™:

The term DiSEqC™ used in this operating manual is a registered trade mark of the European

Telecommunication Satellite Organisation (EUTELSAT).

Legal information

Manufactured under licence from Dolby Laboratories. “Dolby” and the double D

symbol are registered trademarks of Dolby Laboratories.

The terms HDMI and HDMI High-Deﬁ nition Multimedia Interface, and the HDMI

logo are trademarks or registered trademarks of HDMI Licensing LLC in the USA

and other countries.

®

Included in the software for this receiver is software that is licensed under the GNU (General Public

Licence). The source code of the program is available at: http://www.kathrein.de/linux/receiver/ufs913

Software changes/use of applications

Any modiﬁ cations to the receiver software, or the use of applications not provided by Kathrein will

invalidate the warranty! You will have to bear the costs yourself for shipping and repairing any receiver that

requires attention due to modiﬁ cations to the software and use of applications other than those provided

by Kathrein!

Therefore exclusively use only software and applications provided by Kathrein for your receiver. These are

available by downloading from the satellite or from our Internet pages (www.kathrein.de).

Kathrein assumes no liability for the loss of recordings/data on external storage media.

The software installed on the device/product before dispatch from the factory is suitable for its function and

is of the quality usual for this type of software. It has not been technically possible to fully eliminate all bugs

during the software development process. However the software as delivered is defective only if it fails to

perform the functions usual for the device/product. A shortcoming that causes only an insigniﬁ cant reduction

in quality does not rank as a defect. Functional shortcomings in the software or program that result from

hardware defects, ambient conditions, incorrect operation or the like do not rank as software defects.

YouTube and the YouTube logo are trademarks or registered trademarks of

YouTube, LLC.

SHOUTcast™Radio and the SHOUTcast™Radio logo are trademarks or

registered trademarks of Nullsoft Inc.

4

List of Contents

Preface............................................................... 2

Legal information ............................................. 3

List of Contents ................................................ 4

Safety instructions - Important notes ............. 6

Basic functions ............................................... 10

Remote control in live mode (TV/radio) .......... 11

I want to watch TV ... ...................................... 12

I want to listen to the radio ... ......................... 13

I want to access teletext ... ............................. 14

I want to watch time-shift TV ... ...................... 15

I want to record a programme immediately ... 16

I want to record a programme that is scheduled

for later (timer list) .......................................... 17

I want to play back a recording ... .................. 18

I want to delete a recording ... ........................ 19

Editing and selection options in the menus .... 20

Alphanumeric entries ..................................... 21

Switching between TV and radio operation .... 23

Setting the volume ......................................... 23

Channel selection ........................................... 23

... direct .................................................................. 23

... from channel list ................................................ 23

Channel banners (information) ....................... 26

Calling up the channel options ....................... 28

Audio selection ............................................... 29

Subtitle selection ............................................ 30

Teletext ........................................................... 31

Automatic Timeshift ........................................ 32

One Touch Recording (OTR) - recording direct

to hard disk ..................................................... 33

Picture-in-picture ............................................ 35

Explanation of symbols in receiver display .... 36

Electronic Programme Guide (EPG) ............. 37

General information on the programme guide 37

Calling up the EPG ......................................... 38

Navigation (remote control buttons in the EPG)

....................................................................... 39

EPG views ...................................................... 40

“Current” view ........................................................ 40

"Current" view ........................................................ 40

“Preview” view (channel guide) ............................. 41

Categories view ..................................................... 42

Timer list view ........................................................ 43

Timer recording .............................................. 43

Programme present in the EPG ............................ 44

Specifying a target (recording location) ................. 44

Programme not present in the EPG ...................... 44

Specifying a recording mode ................................. 45

Reminder function ................................................. 49

Timer list view ........................................................ 50

Editing a recording ................................................ 51

Timer overlap ......................................................... 52

Search function .............................................. 53

More episodes ....................................................... 53

Presenter - Actor ................................................... 54

Key word search in detailed information ............... 54

Full text search ...................................................... 55

Extras menu ................................................... 56

My hints ................................................................. 56

Actors list ............................................................... 57

Recording archive (playing back/editing recor-

dings) ............................................................... 58

Calling up the recording archive (My recordings)

....................................................................... 58

Navigation (remote control buttons in the recor-

ding archive) ................................................... 59

Recording archive views (sorting the recordings)

....................................................................... 60

Playing back a recording ................................ 61

Editing recordings .......................................... 63

Delete .................................................................... 64

Lock ....................................................................... 64

Rename ................................................................. 64

Change category ................................................... 65

Create new folder .................................................. 66

Move to folder ........................................................ 66

Decrypt in standby ................................................. 66

Copy to external data carrier (such as NAS) ......... 67

Start Blockselection ............................................... 68

Folders in the recording archive ..................... 69

Create new folder ... .............................................. 69

Move to folder ... .................................................... 70

Editing folders (delete/rename) ............................. 71

Chapter view .................................................. 72

Creating chapters .................................................. 72

Opening a chapter ................................................. 72

5

List of Contents

Deleting chapters .................................................. 73

Kathrein portal (Media centre) ....................... 74

Main Menu ....................................................... 75

Calling up the main menu and introduction .... 75

Overview of the main menu submenus .......... 76

Main Menu – Edit Channel List ...................... 77

Calling up the menu ....................................... 77

Navigation (remote control buttons in “Edit TV-

Channellist” menu) ......................................... 79

Views (sort orders) ......................................... 80

Selection of the channel(s) to be edited ......... 81

Edit channels (channel lists) .......................... 81

Move ...................................................................... 82

Delete .................................................................... 82

Skip ....................................................................... 82

Lock ....................................................................... 83

Adding to favourites list ......................................... 83

tvtv on/off ............................................................... 84

Start Blockselection ............................................... 85

Editing favourites lists .................................... 86

Move ...................................................................... 86

Remove from favoritelist ........................................ 86

Lock ....................................................................... 86

Start Blockselection ............................................... 86

Rename favourites list ........................................... 87

Main menu - Search Channels ...................... 88

Calling up the menu ....................................... 88

Automatic Channel Search ............................ 89

Manual Channel Search ................................. 91

Search with service ID ................................... 93

Main menu - Service menu ............................ 95

Calling up the menu ....................................... 95

Automatic software update ............................. 96

Software update (by satellite) ......................... 98

Software Update by USB ............................. 100

Update software .................................................. 100

Update Channel Lists .......................................... 101

Save Channel list to USB .................................... 101

Factory Reset ............................................... 101

Main Menu - Settings .................................... 102

Calling up the menu ..................................... 102

First installation ............................................ 103

Basic Settings .............................................. 103

Video Settings ..................................................... 104

Audio settings ...................................................... 106

Time Setting ........................................................ 107

Remote control code ........................................... 108

User-Defined Settings .................................. 110

Parental lock ........................................................ 110

Customize Screen Menu ..................................... 112

EPG Setup .......................................................... 113

PVR Setup ........................................................... 114

Media centre Setup ............................................. 115

Auto. channel name update ................................ 115

Antenna & Satellites ..................................... 116

Sat Finder ............................................................ 116

Tuner Configuration ............................................. 117

Edit satellites ....................................................... 118

Edit Transponder ................................................. 120

Main menu - Interfaces................................. 124

Calling up the menu ..................................... 124

Common Interface (CI) ................................. 125

Multi-decryption ................................................... 125

Automatic Decryption in standby mode ............... 126

HDD Management ....................................... 126

Format a recording/media archive ....................... 126

Create archive hard disk ..................................... 127

Ethernet Settings .......................................... 129

Main menu - Applications ............................ 130

Calling up the menu ..................................... 130

Main menu - Language Selection ................ 131

Calling up the menu ..................................... 131

Operation from the front panel (without remo-

te control) ...................................................... 132

Backup operation ......................................... 132

Software update via the front USB port ........ 133

Brief technical glossary ............................... 134

Troubleshooting ........................................... 138

Service ........................................................... 139

Subject Index ................................................ 140

6

Safety instructions - Important notes

These two pages contain important information about the operation, installation location and connection of

the unit. Read these instructions carefully before setting up the unit.

Mains cable

Make sure that the mains cable

(power supply cable) is not damaged.

Units with a damaged mains cable

must be disconnected from the mains

(unplugged at the mains power

socket) and repaired by an electrical

specialist before being used. Only

use the power supply unit supplied

(if available)!

Risk of fatal injury due to electric

shock!

Danger!

Cleaning

Disconnect the mains plug before

cleaning the unit. Only use a dry cloth

for cleaning and only clean the outer

surface. Never open the casing of the

unit.

Touching the parts inside the unit

carries a risk of death due to electric

shock!

Playing children

Make sure that children do not push

any objects into the ventilation slots.

Risk of fatal injury due to electric

shock!

Earthing

The antenna system must be

earthed as speciﬁ ed or equipotentially

bonded.

EN 60728/11 and any national

regulations must be complied with.

Risk of voltage surges due to lightning

strikes!

Power supply voltage

Operate the unit only at the speciﬁ ed

mains voltage (indicated on the rear

of the unit or on the external power

supply unit). The unit may only be

connected to the mains and turned

on once it has been connected to the

Moisture, direct sunlight, heat,

naked ﬂ ames

Protect the unit against moisture,

dripping and splashed water (do

not place any ﬁ lled objects such

as vases on top of the unit). Do not

place the unit close to a heater or

expose it to direct sunlight and do

not operate it in damp locations. Only

use the unit in a moderate climate,

not in tropical conditions! Do not

place naked ﬂ ames such as candles

on top of the unit!

There is a risk of ﬁ re!

Ventilation

The heat generated in this unit is

adequately dissipated. However,

the unit should never be installed

in a cupboard or on shelves with

inadequate ventilation. Never cover

the cooling slots on the unit (e.g.

with other equipment, magazines,

tablecloths, clothing or curtains)!

Batteries

If your unit was supplied with

batteries (e.g. for the remote control),

take care that the batteries are

not exposed to excessively high

temperatures, direct sunshine or

ﬁ re. Exchange the batteries only

with types that are identical or

equivalent. Otherwise the batteries

and also the remote control may be

damaged. Also comply with the safety

instructions stated on the batteries:

There is a risk of explosion!

Warning!

antenna and to the TV set or the cable

network and PC.

If the mains voltage is too high, there

is a risk of ﬁ re!

Do not

cover

7

Safety Instructions - Important Notes

Periods of extended absence,

thunderstorms, mains socket

accessibility

In order to disconnect the unit from

the mains completely, the mains

plug must be unplugged from the

wall socket! Therefore install the unit

close to a mains socket and make

sure this socket is accessible at all

times, so that you can disconnect the

unit from the mains if necessary.

If you are away for an extended

period, and during thunderstorms,

always switch the unit off at the

mains and unplug it from the socket.

This also applies to the other

equipment connected to the unit.

Isolation from the cable network is

also recommended. Note any timer

programming (receiver) and turn the

unit on again promptly before the

recording time.

Installation location

All electronic equipment generates

heat. The temperature rise of this

unit does however lie within the

permissible range. Sensitive furniture

surfaces and veneers may become

discoloured by the effects of constant

heat over time. The feet of the unit can

also cause colour changes to treated

furniture surfaces. If necessary, place

the unit on a suitable stable and ﬂ at

base!

Repairs

Ensure that any repairs to your unit

are carried out by qualiﬁ ed personnel.

Opening the unit and attempting to

repair it yourself will void all warranty

claims!

Improper work on the unit may

jeopardise the electrical safety of the

unit.

The manufacturer accepts no liabil-

ity for accidents caused by the user

opening the casing of the unit!

Connections

Incorrect wiring of the connections

can lead to malfunctions or defects on

the unit!

Caution!

Do not place any objects on top of

the unit. Unless stated to the contrary

in the “Connection and set-up” and

“Installation” sections in the manual

supplied, maintain a clearance of at

least 10 cm above the unit, 2 cm to

either side and 5 cm behind the unit,

to allow the unobstructed dissipation

of the heat generated.

There is a risk of ﬁ re!

Electronic equipment is not domestic

waste - it must be disposed of

properly in accordance with directive

2002/96/EC OF THE EUROPEAN

PARLIAMENT AND THE COUNCIL

dated 27

th

January 2003 concerning

used electrical and electronic

appliances.

At the end of its service life, take

this device to a designated public

collection point for disposal.

Spent batteries are special waste!

Do not throw spent batteries into

your domestic waste; take them to a

collection point for spent batteries!

8

Product return/original packaging

Make sure that the ventilation slots on the unit are not blocked or covered in any way.

otherwise the unit may overheat.

There is a risk of ﬁ re!

You must not disconnect the receiver from the mains while it is in operation!

This can lead to a loss of data and corruption of the software.

Safety Instructions - Important Notes

Please keep the original packaging in case you need to return the product at any time! The receivers

are fragile due to their construction and are only adequately protected by the original packaging. If the

receiver is not shipped correctly the guarantee/warranty on it will be voided.

Before you disconnect the receiver from the mains, you must switch it to the standby mode by pressing

the standby button (on/off) on the remote control. In standby mode, any changed or new data that

are broadcast will be saved by the receiver. As soon as the receiver is in the standby mode, it can be

disconnected from the mains at any time.

Ventilation slots on the unit

Switching the receiver off

Warning!

Channel assignment

The channels available on the satellites and transponders are subject to continual change. If changes

do occur, the new channels have to be set on the receiver because the factory pre-programming

corresponds to the status on the date of manufacture. The information for these settings can be found

on the Internet or in relevant magazines.

Updating the receiver software

Your receiver was equipped in the factory with the latest software version available at that time. We

are, however, constantly working on adapting the software to the wishes of our customers and to

developments in technology. Further information on this can be found in the sections “Main Menu - Service

Menu”, “Update Firmware”.

9

The information in this operating manual was correct at the time of going to print. We reserve the right

however to make changes at any time and without prior notice. If new software is released for your

receiver, and this affects the information in the operating instructions (e.g. changes to the menus and/or

functions), if we believe it necessary we will make available new operating instructions for download at

“www.kathrein.de”.

Make a note of the receiver's basic settings (these are set during the ﬁ rst installation), so you can restore

them if necessary!

Please be aware of your responsibility towards your fellow human beings! Keep this manual

for any questions that arise later, and if the receiver passes to another owner, pass it on to the

new owner.

For compliance with the EMC Directives, the USB connection cable between the receiver and hard disk

must not be longer than 50 cm.

Please see the UFS 913 Operating manual – Part 1, “Connection and set-up” for details on how to

connect the receiver and carry out ﬁ rst installation.

The following description of the menus and functions assumes that the UFS 913 has been correctly

connected and installed (as detailed in the operating instructions part 1 “Connection and set-up”).

Miscellaneous

Safety Instructions - Important Notes

Network function

To connect the receiver to the network via the PC/laptop, you must have unrestricted rights (administrator

rights) for your PC/laptop and on your network. For this refer to the chapter “Main Menu”, “Interfaces”,

“Network Settings”.

Power consumption in standby mode < 0.5 W

The standby power consumption of < 0.5 W printed on the receiver packaging will only be achieved when

the receiver is in standby mode with the display switched off. You can deﬁ ne this setting in the following

menu: “Main menu”, “Settings”, “User-Deﬁ ned Settings”, “Customize Screen Menu”, “Front display

in standby” → Setting “Off”.

10

Basic functions

Following an overview of the remote control, a simple explanation will be provided of the receiver’s

most important functions (with all the required buttons on the remote control). The explanations in the

sections “I would like to ...” merely demonstrate the most simple use of the relevant receiver functions

without going into any great detail.

For more detailed explanations of the functions, refer to the relevant sections.

11

Basic functions

The coloured buttons are

reserved for certain content-

dependent functions

(e.g. teletext ...)

Volume “-” (softer)

Volume “+” (louder)

Call up teletext

Operation (on)/standby (off)

Switch between TV/radio mode

Number pad

Call up main menu

Mute

Channel selection

Calling up channel

information (info banner

and detailed information)

Calling up tvtv EPG (Electronic

Programme Guide)

Calling up recording archive



= Navigation/channel

or change channel option



= Calling up selection box/

conﬁ rmation or calling up of

selected menus, on-screen

displays ...

Calling up Media centre/

Kathrein portal



= Start timeshift

(freeze-frame)/pause



= Start recording (OTR)

= Stop playback/

timeshift/recording



= Fast rewind



= Start playback



= Fast forward

Select last channel called up,

exit on-screen displays/

menus step by step

Remote control in live mode (TV/radio)

OTR = One Touch Recording

If an external device is connected to the VCR Scart socket, the

TV signal present at the VCR Scart socket can be looped through

to the TV Scart socket. Pressing the



button more than

once toggles between the TV Scart mode and the VCR Scart

loop-through mode.

12

Basic functions

I want to watch TV ...

- Press



to increase or decrease the volume

- Press



to switch channels

- Press



to display and hide additional channel information

- Press



to mute sound

- Press



...



to enter the channel number directly

- Press



to open the selection box,



to select the channel list

and call up using



- Press



to select a channel

- Press



twice to call up a

channel and close the channel

list

13

Basic functions

- Press



to increase or decrease the volume

- Press



to switch channels

- Press



to display and hide additional channel information

- Press



to mute sound

- Press



...



to enter the channel number directly

- Press



to open the selection box,



to select the channel list

and call up using



- Press



to select a channel

- Press



twice to call up a

channel and close the channel

list

- Press



to change to radio mode

- Press



to change back to TV mode

I want to listen to the radio ...

14

Basic functions

I want to access teletext ...

- Press



...



to enter the required page directly

or

- Press



browse forward/backward page-by-page

- Press



to call up teletext

- Press



or



to return to TV

15

Basic functions

I want to watch time-shift TV ...

- Press



to start timeshift

Made a

mistake?

- Press



to cancel timeshift

- Press



to start playback

- Press



during playback to fast forward and rewind

- Press



to return to normal playback speed

- Press



to pause playback

- Press



to cancel timeshift and return to normal (live) TV

To watch time-shift TV using the UFS 913 you must connect an external hard disk

*)

to the USB port on the rear of the receiver and set it up as described in the

“Main menu - interfaces”, “Hard disk management” section.

*)

Tested only with hard disks from the Kathrein product range (see also:

www.kathrein.de → Service → FAQs)

16

I want to record a programme immediately ...

Basic functions

- Press the



(red dot) button to open the “Recording” window

- Press



to start recording the

programme

or

- Press



to change the

duration before recording

Made a

mistake?

- Press



or



to close the window without recording

- Press



and



to stop a recording that is in progress

To make recordings using the UFS 913 you must connect an external hard disk

*)

to the USB port on the rear of the receiver and set it up as described in the

“Main menu - interfaces”, “Hard disk management” section.

*)

Tested only with hard disks from the Kathrein product range (see also:

www.kathrein.de → Service → FAQs)

17

I want to record a programme that is scheduled for later (timer list)

Basic functions

- Press the



button to open the

programme guide

- Press



to select the desired programme

- Press the



button to open the

“Recording” window.

- Press



to start recording the

programme

or

- Press



to change the recording mode, date, start, end and duration

before recording

- Press



or



to return to TV

- Press the



(yellow) button to

call up the programme preview

- Press



to select the desired channel

To make recordings using the UFS 913 you must connect an external hard disk

*)

to the USB port on the rear of the receiver and set it up as described in the

“Main menu - interfaces”, “Hard disk management” section.

*)

Tested only with hard disks from the Kathrein product range (see also:

www.kathrein.de → Service → FAQs)

18

Basic functions

- Press



(or



) to open the “My Recordings” recording archive

- Press



to select a recording

- Press



to start playback and

exit the recording archive

- Press



during playback to fast forward and rewind

- Press



to return to normal playback speed

- Press



to pause playback

- Press



to cancel playback and return to the recording archive

- Press



to exit the recording archive and return to normal (live) TV

I want to play back a recording ...

To record programmes using the UFS 913 and then be able to play them back, you

must connect an external hard disk

*)

to the USB port at the rear of the receiver and

set it up as described in the “Main menu - interfaces”, “Hard disk management”

section.

*)

Tested only with hard disks from the Kathrein product range (see also:

www.kathrein.de → Service → FAQs)

19

Basic functions

I want to delete a recording ...

- Press



(or



) to open the “My Recordings” recording archive

- Press



to select a recording

- Press



to exit the recording archive and return to normal (live) TV

- Press the



button to open the

“Edit” menu

- Press



to select the “Delete” option, then



to conﬁ rm

- Press



to conﬁ rm the security question

20

Basic functions

Editing and selection options in the menus

In many menus all editing and selection options

for the respective menu will appear at the bottom

of the on-screen display. Where a speciﬁ c remote

control button is required for executing them

or calling them up, this also will be shown (see

screenshot example above).

Colour Button on the remote control

Green

Yellow

Red

Blue

In some menus/on-screen displays

this box is shown with a particular

colour gradation. Each colour gradation

represents a speciﬁ c view/selection. The

table below shows which colours are

assigned to which buttons. Where the

functions of these buttons are assigned

for the current menu/view, they are also

shown in the line at the bottom of the

on-screen display.

Always check the bar at the bottom of

the on-screen display. This provides

information on what to do next.

Tip!

Page is loading ...

Kathrein UFS 913sw Operating Instructions Manual

This manual is also suitable for

Kathrein UFS 913sw Operating Instructions Manual

Related papers

Other documents