CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Op e r a t O r ’s Ma n u a l
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
Z-Force S 60
Liquid Propane Gas
Form No. 769-05905
(March 9, 2010)
Customer Support
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:
Visit us on the web at www.cubcadet.com◊
Locate your nearest Cub Cadet Dealer at (877) 282-8684◊
◊
Thank you for purchasing a Cub Cadet Zero-Turn Tractor. It was
carefully engineered to provide excellent performance when
properly operated and maintained.
It instructs you how to safely and easily set up, operate and
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.
All information in this manual is relative to the most recent
product information available at the time of printing. Review
this manual frequently to familiarize yourself with the machine,
Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. We reserve
the right to change product specifications, designs and
equipment without notice and without incurring obligation.
If you have any problems or questions concerning the machine,
phone your local Cub Cadet dealer or contact us directly. Cub
and mailing address can be found on this page. We want to
ensure your complete satisfaction at all times.
Throughout this manual, all references to right and left side of the
machine are observed from the operating position.
Thank You
Record Product Information
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by standing at the left side of the tractor, pivoting
the seat forward and looking down at the seat frame. This
information will be necessary, should you seek technical support
via our web site or with your local Cub Cadet dealer.
MO d e l nu M b e r
se r i a l nu M b e r
To The Owner
1
2
Safe Operation Practices ........................................ 3
Assembly & Set-Up .................................................. 9
Controls & Features ................................................12
Operation ................................................................15
Maintenance & Adjustment..................................19
Service .................................................................... 26
Troubleshooting .....................................................31
Replacement Parts ................................................ 32
Attachments & Accessories .................................. 34
Warranties ............................................................. 38
Table of Contents
Important Safe Operation Practices
2
3
General Operation
Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
2.
Know how to stop the machine and disengage them
quickly.
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
Never allow adults to operate this machine without proper 4.
instruction.
To help avoid blade contact or a thrown object injury, 5.
keep bystanders, helpers, children and pets at least 75 feet
anyone enters the area.
Thoroughly inspect the area where the equipment is to be 6.
used. Remove all stones, sticks, wire, bones, toys, and other
foreign objects which could be picked up and thrown by
the blade(s). Thrown objects can cause serious personal
injury.
7.
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction
which may cause discharged material to ricochet back
toward the operator.
Always wear safety glasses or safety goggles during 8.
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Loose fitting clothes and jewelry can be
caught in movable parts. Never operate this machine in
bare feet or sandals.
and do not point it at anyone. Do not operate the mower
without the discharge cover or entire grass catcher in its
proper place.
Do not put hands or feet near rotating parts or under the
cutting deck. Contact with the blade(s) can amputate
hands and feet.
A missing or damaged discharge cover can cause blade
contact or thrown object injuries.
roads and while not cutting grass.
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
DANGER! This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating hands and feet
and throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
or other reproductive harm.
WARNING!
harm. Wash hands after handling
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s
Watch for traffic when operating near or crossing
roadways. This machine is not intended for use on any
public roadway.
Do not operate the machine while under the influence of
alcohol or drugs.
Mow only in daylight or good artificial light.
Never carry passengers.
and pay attention to the safety system function that
stops power to the blades when driving in reverse. If not
fuctioning properly, contact an authorized dealer for safety
system inspection and repair.
Avoid erratic operation and excessive speed.
Disengage blade(s), set parking brake, stop engine and wait
until the blade(s) come to a complete stop before removing
grass catcher, emptying grass, unclogging chute, removing
any grass or debris, or making any adjustments.
Never leave a running machine unattended. Always turn off
blade(s), place drive control levers in neutral, set parking
brake, stop engine and remove key before dismounting.
Use extra care when loading or unloading the machine into 22.
a trailer or truck. This machine should not be driven up or
down ramp(s), because the machine could tip over, causing
serious personal injury. The machine must be pushed
manually on ramp(s) to load or unload properly.
Muffler and engine become hot and can cause a burn. Do
not touch.
Check overhead clearances carefully before driving under 24.
low hanging tree branches, wires, door openings etc.,
where the operator may be struck or pulled from the
machine, which could result in serious injury.
Disengage all attachment clutches, set the parking brake to 25.
the ‘ position.
Your machine is designed to cut normal residential grass of 26.
unusually tall, dry grass (e.g., pasture) or piles of dry leaves.
Dry grass or leaves may contact the engine exhaust and/
or build up on the mower deck presenting a potential fire
hazard.
Use only accessories and attachments approved for this 27.
machine by the machine manufacturer. Read, understand
and follow all instructions provided with the approved
accessory or attachment.
28.
involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability
to operate the riding mower safely enough to protect
themselves and others from serious injury.
If situations occur which are not covered in this manual, use
care and good judgment. Contact your customer service
representative for assistance.
Slope Operation
accidents which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not mow it.
For your safety, use the slope gauge included as part of this
manual to measure slopes before operating this machine on
shown on the slope gauge, do not operate this machine on that
area or serious injury could result.
Do:
Mow across slopes, not up and down. Exercise extreme
caution when changing direction on slopes.
Watch for holes, ruts, bumps, rocks, or other hidden 2.
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.
Use slow speed. Choose a low enough speed so that you
will not have to stop while on the slope. Avoid starting
or stopping on a slope. If the tires are unable to maintain
traction, disengage the blades and proceed slowly and
carefully straight down the slope.
4.
weights or counterweights to improve stability.
Use extra care with grass catchers or other attachments. 5.
These can change the stability of the machine.
Keep all movement on the slopes slow and gradual. Do 6.
not make sudden changes in speed or direction. Rapid
acceleration or deceleration could cause the front of the
machine to lift and rapidly flip over backwards, which
could cause serious injury.
Do Not:
Do not turn on slopes unless necessary; then turn slowly
uphill and use extra care while turning.
Do not mow near drop-offs, ditches or embankments. The 2.
mower could suddenly turn over if a wheel is over the edge
of a cliff, ditch, or if an edge caves in.
Do not try to stabilize the machine by putting your foot on
the ground.
Do not use a grass catcher on steep slopes. 4.
Do not mow on wet grass. Reduced traction could cause 5.
sliding.
Do not tow heavy pull behind attachments (e.g. loaded 6.
dump cart, lawn roller, etc.) on slopes greater than 5
degrees. When going down hill, the extra weight tends to
push the tractor and may cause you to lose control (e.g.
tractor may speed up, braking and steering ability are
reduced, attachment may jack-knife and cause tractor to
overturn).
5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s
Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. They do not understand
the dangers. Never assume that children will remain where
you last saw them.
Keep children out of the mowing area and in a.
watchful care of a responsible adult other than the
operator.
b.
area.
To avoid back-over accidents, always look behind c.
and down for small children.
Never carry children, even with the blade(s) shut off. d.
They may fall off and be seriously injured or interfere
with safe machine operation.
Use extreme care when approaching blind corners, e.
doorways, shrubs, trees or other objects that may
block your vision of a child who may run into the
path of the machine.
Keep children away from hot or running engines. f.
They can suffer burns from a hot muffler.
Remove key when machine is unattended to g.
prevent unauthorized operation.
2.
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
Towing
Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
Follow the manufacturers recommendation for weight 2.
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
4.
loss of traction and loss of control.
5.
Never allow passengers on the towed equipment.6.
7.
grade.
Travel slowly and allow extra distance to stop.8.
Use caution during turns to avoid jack-knifing.
Use extra caution when operating in reverse.
Do not modify or repair the hitch, replace the hitch if
damaged.
Travel slowly and allow extra distance to stop.
Do not shift to neutral and coast downhill.
Service
Related to Fuel:
DANGER! Never have the mower near an open
flame or spark, or allow smoking when refueling the
2.
appropriate clothing, gloves and eyewear.
If you smell or see gas, or hear the hiss of escaping gas,
immediately get away from the cylinder and contact your
local fire department.
Do not smoke or permit others to smoke while handling 4.
5.
Always close the valves on the cylinders when not in use.6.
7.
8.
is running.
Cylinders must be filled by trained personnel only.
away from sparks and flames.
Always shut off the engine and permit it to cool before
tanks, make sure that the nozzles are free of any debris
that might clog or damage the nozzle. Debris in the nozzle
or damage to the nozzle may cause a failure of the check
valve, which may compromise the seal and become a fire
hazard.
General Service
DANGER! Never modify or tamper with the
cylinder, hoses, check valves, shut-off valve, or
regulator as this could result in poor system
performance, leakage, and a fire hazard.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless,
and deadly gas.
2.
blade(s) and all moving parts have stopped. Disconnect the
spark plug wires and remove the key from the ignition to
prevent unintended starting.
complete stop within approximately (7) seven seconds
after operating the blade disengagement control. If
the blades do not stop within the this time frame, your
machine should be serviced.
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s
Regularly check the safety interlock system for proper 4.
function, as described later in this manual. If the safety
interlock system does not function properly, have your
machine serviced.
Check the blade(s) and engine mounting bolts at frequent 5.
intervals for proper tightness. Also, visually inspect blade(s)
for damage (e.g., excessive wear, bent, cracked). Replace
which do not meet the original equipment specifications
may lead to improper performance and compromise
Mower blades are sharp. Wrap the blade or wear gloves, 6.
and use extra caution when servicing them.
Keep all nuts, bolts, and screws tight to be sure the 7.
equipment is in safe working condition.
Never tamper with the safety interlock system or other 8.
safety devices. Check their proper operation regularly.
After striking a foreign object, stop the engine, disconnect
the spark plug wire(s) and ground against the engine.
Thoroughly inspect the machine for any damage. Repair
the damage before starting and operating.
Never attempt to make adjustments or repairs to the
machine while the engine is running.
subject to wear and damage which could expose moving
parts or allow objects to be thrown. For safety protection,
frequently check components and replace immediately
listed in this manual. Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!
Do not change the engine governor settings or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
Do not tamper with or adjust the regulator since the
the exhaust emissions compromised — this could result
damage to the engine and exhaust system with possible
set to provide optimal performance in regard to power and
emissions.
Maintain or replace safety and instruction labels, as
necessary.
etc. to protect the environment.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
and may include the following emission control systems: Engine
Modification (EM) and Three Way Catalyst (TWC) if so equipped.
Spark Arrestor
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush-
exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in
Federal laws apply on federal lands.
A spark arrester for the muffler is available through your
nearest engine authorized service dealer or contact the service
7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s
WARNING! Your Responsibility — Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol Description
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
Do not put hands or feet near rotating parts or under the cutting deck. Contact with the
blade(s) can amputate hands and feet.
This machine may pick up and throw and objects which can cause serious personal injury.
This machine may pick up and throw and objects which can cause serious personal injury.
Keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in
operation.
To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover
or grass catcher is in its proper place. If damaged, replace immediately.
This cylinder is designed to contain a liquified petroleum gas under pressure that is
requirements.
8 se c t i O n 2 — sa f e Op e r a t i O n pr a c t i c e s
Sight and hold this level with a vertical tree...
or a corner of a building...
or a fence post
Fold along dotted line (represents a 15° slope)
15°
Use this page as a guide to determine slopes where you may not operate safely.
WARNING!
bottom of the slope and turn uphill at the end of each pass whenever possible.
Assembly & Set-Up
3
9
Contents of Crate
Manual
Tractor Preparation
Unpacking the Tractor
Remove the upper crating material from the shipping pallet,
and cut any bands or tie straps securing the tractor to the
pallet.
If the deck is not in the highest mowing position (pushed all 2.
the way forward), use the deck lift pedal to raise the deck to
for instructions on raising and lowering the deck.
Disengage the parking brake.
Engage the transmission bypass rods on each side of the 4.
tractor; then carefully roll the tractor off the shipping pallet.
transmission) are located on the rear of the tractor, just
Remove the deck wash system nozzle adapter and oil drain 5.
tube from the manual bag and store for future use.
Initial LPG Tank Fill-Up
NOTE: The vapor withdrawal service valve of the Aluminum
threaded safety coupler. Typical forklift cylinders withdraw liquid
propane and have right-handed safety couplers. The different
safety couplers prevent users from installing cylinders on the
wrong equipment.
before the initial fill-up.
It is important to properly purge new propane cylinders before
Installing the LPG Tank Straps
The tank straps need to be installed before the tank can be
installed. To install the tank proceed as follows:
Remove the strap assemblies, alignment pin and two bolts
from the box. Then remove the four hex screws and flange
lock nuts from the manual bag.
Mount the alignment pin to the strap assembly using the 2.
flange lock nuts mount the strap assemblies to the mount
Keyhole Slot
Transmission
Bypass Rods
Figure 3-1
Strap Assemblies
Hex Screws
Flange Lock Nuts
Mount Plate
Figure 3-2
10 se c t i O n 2— as s e M b l y & se t -up
Installing the LPG Tank
sure that the alignment pin fits into the slot on the bottom
When the tank is in place, secure it by locking down the 2.
NOTE: The hose has left-handed threads to prevent
improper usage.
Steering Wheel Column
The steering wheel column is tilted all the way back for shipping
purposes. To tilt the column forward, press the steering tilt pedal.
Release the steering tilt pedal when the column is in the desired
position.
Steering Wheel
Remove the hardware for attaching the steering wheel
from beneath the steering wheel cap. Carefully pry off the
steering wheel cover to remove the hardware.
With the wheels of the tractor pointing straight forward, 2.
place the steering wheel over the steering shaft.
4.
place.
Steering Wheel Cover
Hex Screw
Flat Washer
Steering Wheel
Steering Wheel
Column
Belleville Washer
Figure 3-5
Cylinder Valve Guard
Alignment Pin
Slot
Figure 3-3
A
A
B
C
Figure 3-4
11se c t i O n 2 — as s e M b l y & se t -up
Install Operator’s Seat
To install the seat proceed as follows:
NOTE: The seat is shipped with the seat switch and seat pan
attached. A second person may be needed to hold the seat.
Cut any straps securing the seat assembly to the tractor.
Remove any packing material.
NOTE:
seat and the seat switch in the bottom of the seat.
Remove the two shoulder bolts and lock nuts in the seat 2.
Rotate the seat into position and secure the seat into place
with the previously removed shoulder bolts and lock nuts.
Figure 3-8
Figure 3-6
Figure 3-7
Connecting the Battery Cables
CALIFORNIA PROPOSITION 65 WARNING!
contain lead and lead compounds, chemicals known
reproductive harm. Wash hands after handling.
CAUTION: When attaching battery cables, always
For shipping reasons, both battery cables on your equipment
may have been left disconnected from the terminals at the
factory. To connect the battery cables, proceed as follows:
NOTE:
negative battery terminal is marked Neg. (–).
NOTE: If the positive battery cable is already attached, skip
ahead to step 2.
Remove the plastic cover, if present, from the positive
battery terminal and attach the red cable to the positive
Remove the plastic cover, if present, from the negative 2.
battery terminal and attach the black cable to the negative
terminal to help protect it from corrosion.
NOTE: If the battery is put into service after the date shown
on top/side of battery, charge the battery as instructed in the
the tractor.
Controls & Features
4
12
Ignition
Switch
Module
Hour Meter/
Indicator Panel
PTO Switch
Index Plate
Deck Lift Pedal
Drive Pedal
Reverse Pedal
Throttle Control
Seat Adjustment Lever
Parking Break
Engagement Lever
LPG Tank
E
F
1/4
1/2
L.P .
GAS
FUEL
OK
OK
D
D
A
V
E
R
T
I
C
A
L
H
O
R
I
Z
O
N
T
A
L
Fuel
Valve
Fuel
Gauge
Relief
Valve
Valve
Fill
Figure 4-1
NOTE:
position on the tractor when facing forward while seated in the
Deck Lift Pedal
2
L
4
5
6
7
8
4
5
The deck lift pedal is located near the front of the tractor on the
left of the foot platform and is used to raise and lower the mower
position.
position, locking behind the notch on the front of the index
plate. Remove and replace the lock pin into the desired height
index hole, then push pedal forward and rock forward to unlock
and slowly allow the pedal to move back until it reaches the lock
pin.
Ignition Switch Module
WARNING! Never
leave a running
machine unattended.
Always disengage
brake, stop engine
and remove key to
prevent unintended
starting.
To start the engine, insert the key
into the ignition switch and turn
clockwise to the position.
Release the key into the position once
the engine has fired.
To stop the engine, turn the ignition key counter-clockwise to the
CAUTION:
Module and operating the tractor in
.
13se c t i O n 4 — cO n t r O l s & fe a t u r e s
PTO (Power Take-Off ) Switch
clutch mounted on the bottom of the engine
downward to disengage the clutch.
position when starting the engine.
Transmission Bypass Rods (Not Visible)
transmission) are located on the rear of the tractor, just inside
each rear wheel, below the storage trays.
When engaged, the two rods open a bypass within the
hydrostatic transmissions, which allows the tractor to be pushed
short distances by hand.
CAUTION: Never tow your tractor. Towing the
tractor with the rear wheels on the ground may
cause severe damage to the transmissions.
Cup Holder
Storage Tray
Seat Adjustment Lever
The seat adjustment lever is located below the front/left of the
seat. The lever allows for adjustment of the fore to aft position
section for instructions on adjusting the seat position.
Fuel Valve
turned in a clockwise direction until it stops, it will shut off the
flow of fuel to the engine. When turned in a counter-clockwise
direction it will open and allow fuel to flow to the engine.
Fuel Gauge
tank, the fuel gauge measures the
fuel level in each tank.
E
F
1/4
1/2
L.P .
GAS
FUEL
OK
OK
D
D
A
V
E
R
T
I
C
A
L
H
O
R
I
Z
O
N
T
A
L
Hour Meter/Indicator Panel
The hour meter/indicator panel is
Hour Meter Features
The hour meter records the hours that
the tractor has been operated in the
digital display (tenths of an hour - right
most digit).
NOTE: The hour meter is activated whenever the ignition switch
of operation to assure all maintenance procedures are completed
according to the instructions in this manual and the engine
manual.
light briefly illuminates and the battery voltage is briefly
displayed. The display then changes to the accumulated hours.
The Indicator Monitor will also remind the operator of
maintenance intervals for changing the engine oil. The LCD
interval. Follow the oil change intervals provided in the engine
manual.
Throttle Control
given position, a uniform engine speed will be
maintained.
the engine speed. The tractor is designed to operate
with the throttle control in the fast position (full
throttle) when the tractor is being driven and the
mower deck is engaged.
speed.
Parking Brake Engagement Lever
The parking brake engagement lever is located on the left
of the seat box frame, and is used to engage the parking
brake.
completely forward to disengage the parking brake.
HOURS 1/10
PTO
/
B
L
A
D
E
PA
R
K
B
R
A
K
E
O
I
L
BATT.
FA ST
S W
14 se c t i O n 4— cO n t r O l s & fe a t u r e s
Indicator Panel Features
Battery Indicator
Illuminates and the battery voltage is displayed briefly when the
Illuminates to indicate the battery voltage has dropped below
the hour meter. If this indicator and display come on during
operation, check the battery and charging system for possible
causes and/or contact your Cub Cadet dealer.
Oil Pressure Indicator (If Engine So Equipped)
This warning lamp indicates low engine oil pressure. If the
indicator comes on while the engine is running, stop the engine
immediately and check for possible causes. Do not run the
engine while this indicator is illuminated. Contact your Cub
Cadet dealer to have the tractor and engine inspected.
NOTE: The oil pressure indicator may illuminate when the
the engine is started.
PTO Engaged Indicator
Parking Brake Engaged Indicator
This indicator illuminates when the parking brake is in the
This indicator also illuminates when the ignition switch is turned
are in a position other than the fully out in neutral position. Move
the control levers fully outward.
Drive Pedal
The drive pedal is located on the right side
the drive pedal forward to cause the tractor to
with the drive pedal. The further forward the
pedal is pivoted, the faster the tractor will travel. The pedal will
Reverse Pedal
The reverse pedal is located on the right
side of the tractor along the running board.
reverse pedal. The further downward the
pedal is pivoted, the faster the tractor will
travel. The pedal will return to its original
Transmission Oil Expansion Reservoir (Not Shown)
The transmission oil expansion reservoir is connected by hoses
the seat box. The function of the reservoir is to hold the natural
expansion of transmission oil that occurs as the transmission
Under normal operating conditions, no oil should be added
approximately ⁄
NOTE:
the reservoir may be slightly higher than the maximum due to air
air from the lines and the oil level will settle to the maximum.
Full Cold Line
Figure 4-2
Operation
5
15
General Safety
competent in its usage to operate this tractor.
familiar with the controls. The operator should be in the
position and the parking brake engaged.
Keep all shields in place. Keep away from moving parts.
Look behind and down to both sides of the tractor before
and while backing up.
Avoid slopes where possible. Never operate on slopes
dangerous operating conditions. Tractors can be rolled
over.
engage the parking brake, shut off the engine and remove
the ignition key. Wait for all movement to stop before
servicing or cleaning.
Avoid any sudden movements of the steering wheel when
starting and stopping. Keep a firm grip on the steering
wheel.
motion and wait for vehicles to pass before operating
along the road.
Do not operate the tractor with the mower deck removed.
Removal of the deck will change the balance of the tractor,
and could contribute to a tractor rollover.
Avoid operation on traction surfaces that are unstable; use
extreme caution if the surface is slippery.
before any zero turn maneuver.
Do not stop the tractor or park the tractor over
combustible materials such as dry grass, leaves, debris, etc.
Before Operating Your Tractor
to familiarize yourself with the operation of all the
instruments and controls. It has been prepared to help you
operate and maintain your tractor efficiently.
Check the engine oil level.
Clean the air cleaner element if necessary.
Check the tire inflation pressures.
and for maintaining complete control of the tractor.
Safety Interlock Switches
This tractor is equipped with a safety interlock system for the
protection of the operator. If the interlock system should ever
malfunction, do not operate the tractor. Contact your Cub Cadet
dealer.
The safety interlock system prevents the engine from
cranking or starting unless the parking brake is engaged,
The engine will automatically shut off if the operator leaves
the seat before engaging the parking brake.
WARNING! Do not operate the tractor if the
interlock system is malfunctioning. This system was
designed for your safety and protection.
16 se c t i O n 5— Op e r a t i O n
Starting the Engine
WARNING! This tractor is equipped with a safety
interlock system designed for the protection of the
operator. Do not operate the tractor if any part of
check the functions of the interlock system for
proper operation.
WARNING! For personal safety, the operator must
be sitting in the tractor seat when starting the
engine.
2.
control pedals in the neutral/start position.
4.
position.
5.
temperatures).
6.
and release it as soon as the engine starts; however, do not
at a time. If the engine does not start within this time, turn
Cold Weather Starting
When starting the engine at temperatures near or below
freezing, ensure the correct viscosity motor oil is used in the
follows:
has much more starting capacity than a cold battery.
NOTE:
for shut-off valve to function correctly. This also provides
desired engine cranking speed.
2.
Crank engine for about 5 seconds and stop.
4.
starts running.
Repeat if necessary.5.
Using Jumper Cables To Start Engine
WARNING!
produce explosive gasses. Make certain the area is
well ventilated, wear gloves and eye protection, and
avoid sparks or flames near the battery.
If the battery charge is not sufficient to crank the engine,
recharge the battery. If a battery charger is unavailable and
the tractor must be started, the aid of a booster battery will be
necessary. Connect the booster battery as follows:
Connect the end of one cable to the disabled tractor
Connect one end of the other cable to the booster 2.
that cable to the frame of the disabled tractor, as far from
the battery as possible.
instructions previously provided; then disconnect
the jumper cables in the exact reverse order of their
connection.
4.
as soon as possible to eliminate the need for jump starting.
Stopping the Engine
Move the speed control pedals to the neutral position. 2.
Engage the parking brake.
Move t4.
ositions.
Turn t5.
key from the ignition switch.
NOTE: Always remove the key from the ignition switch
to prevent accidental starting or battery discharge if the
equipment is left unattended.
Close the fuel supply valve.6.
Engage the Parking Brake
Figure 5-1
17se c t i O n 5 — Op e r a t i O n
Driving The Tractor
WARNING! Avoid sudden starts, excessive speed
and sudden stops.
Release the parking brake. Move the throttle lever into the
2.
To stop or slow down the tractor, take your foot off of the
forward or reverse drive pedal. To lock the parking brake,
pull the lever fully rearward and to the right; then into the
disengage the parking brake.
NOTE: The forward and reverse pedals must not be used when
the brake is partially engaged. When the brake is locked in the
back then the brakes are engaged but so is the drive belt so
transmission damage will occur if you push forward or reverse.
4.
CAUTION:
direction of travel when the tractor is in motion.
Always bring the tractor to a complete stop before
moving the tractor from forward to reverse or vice
versa.
WARNING! Do not leave the seat of the tractor
parking brake. If leaving the tractor unattended, also
turn the engine off and remove the ignition key.
Reverse Caution Mode
engaged.
NOTE: Mowing in reverse is not recommended.
WARNING! Use extreme caution while operating
look down and behind before and while backing. Do
not operate the tractor when children or others are
enters the area.
NOTE:
page.
2.
The red indicator light at the top, left corner of the key
4.
Always look down and behind before and while backing to 5.
make sure no children are around. After resuming forward
a.
The operator leaves the seat.b.
Travel Forward
Travel in Reverse
Figure 5-2
Indicator
Light
Reverse
Push Button
Stop
Position
Start
Position
Reverse
Caution Mode
Position
Figure 5-3
18 se c t i O n 5— Op e r a t i O n
Driving On Slopes
where you may operate the tractor safely.
WARNING! Do not mow on inclines with a slope in
⁄
cause serious injury.
Mow across slopes, not up and down.
Exercise extreme caution when changing direction on
slopes.
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.
Do not turn on slopes unless necessary; then turn slowly
uphill and use extra care while turning. Turning up a slope
greatly increases the chance of a rollover.
Avoid stopping when driving up a slope. If it is necessary
to stop while driving up a slope, start up smoothly and
carefully to reduce the possibility of flipping the tractor
over backward.
Mowing
WARNING! To help avoid blade contact or a
thrown object injury, keep bystanders, helpers,
children and pets at least 75 feet from the machine
enters the area.
The following information will be helpful when using the cutting
deck with your tractor.
WARNING!
discharge of materials toward roads, sidewalks,
bystanders and the like. Also, avoid discharging
material against a wall or obstruction which may
cause discharged material to ricochet back toward
the operator.
Do not mow at high ground speed, especially if a mulch kit
or grass collector is installed.
growth and yellows quickly in dry weather.
Always operate the tractor with the throttle lever in the
For best results it is recommended that the first two laps be
cut with the discharge thrown towards the center. After the
first two laps, reverse the direction to throw the discharge
to the outside for the balance of cutting. This will give a
better appearance to the lawn.
extremely tall grass. Your tractor is designed to mow lawns,
Keep the blades sharp and replace the blades when worn.
Using the Deck Lift Pedal
locking behind the notch on the front of the index plate. Remove
and replace the lock pin into the desired height index hole, then
press down on the lift pedal and slowly allow the pedal to move
back until it reaches the lock pin.
Engaging the PTO
position.
2.
NOTE: Always operate the tractor with the throttle lever in the
deck or other (separately available) attachments.
ON
OFF
Figure 5-4
Maintenance & Adjustments
6
19
Maintenance Schedule
Before
Each use
Every
10 Hours
Every
25 Hours
Every
50 Hours
Every
100 Hours
After
Mowing
Prior to
Storing
Check engine oil/LPG level
P P
Check Air Filter for Dirty, Loose or Damaged Parts
P P
Check LPG valve, hoses and seals
P
Check hydraulic hoses for leaks
P
Check tires & tire pressure
P
Check deck, mower and hydro drive belts
P
Check blades and blade bolt tightness
P
Check safety switches for proper operation
P
Check fluid level in transaxle expansion reservoir
P
Check engine intake screen/cover
P
Clean mower
P
Lube Front Caster Wheels and Wheel Spindles
P P
Clean and Re-oil Air Filter’s Foam Precleaner *
P
Grease three spindle bearings
P
Replace air filter element *
P
Change engine oil † and replace oil filter
P
Clean Battery Terminals
P P
Clean engine cooling fins & external surfaces *
P P
Lubricate deck spindles
P P
Lube Pedal Pivot Points
P P
Check spark plug condition & gap
P
20 se c t i O n 6— Ma i n t e n a n c e & ad j u s t M e n t s
Maintenance
WARNING!
engine and remove key to prevent unintended
starting.
Engine
page 2 for more information.
procedures and instructions.
NOTE: Maintenance, repair, or replacement of the emission
expense may be performed by any engine repair establishment
or individual. Warranty repairs must be performed by a Cub
Cadet Dealer.
Changing the Engine Oil
WARNING! If the engine has been recently run, the
engine, muffler and surrounding metal surfaces will
be hot and can cause burns to the skin. Exercise
caution to avoid burns.
NOTE: The oil filter should be changed at every oil change interval.
To complete an oil change, proceed as follows:
Run the engine for a short time to warm the engine oil. The
oil will flow more freely and carry away more impurities.
Use care to avoid burns from hot oil.
Locate the oil drain port on the right side of the engine.2.
the oil fill cap/dipstick from the oil fill tube.
4.
oil drain port. Route the opposite end of the hose into an
capacity, to collect the used oil.
Turn the oil drain valve 5. ⁄-turn, then pull outward to begin
draining oil. After the oil has finished draining, push the
end of the oil drain valve back in and turn ⁄turn to secure
it back in place Re-cap the end of the oil drain valve to
keep debris from entering the drain port.
After the oil has finished draining, push the end of the oil 6.
drain valve back in, until the tabs click into place. Re-cap
the end of the oil drain valve to keep debris from entering
the drain port.
Replace the oil filter, and refill the engine with new oil as 7.
Changing the LPG Tank
WARNING ! If the engine has been recently run, the
engine, muffler and surrounding metal surfaces will
be hot and can cause burns to the skin. Exercise
caution to avoid burns.
Make sure the tractor is off and the key is removed from the
ignition.
Ensure that the fuel supply valve is turned off.2.
NOTE: The hose has left-handed threads to prevent
improper usage.
Release the two (2) straps that secure the cylinder to the 4.
Carefully lift cylinder straight up to remove from machine. 5.
6.
refueling.
DANGER! An overfilled cylinder can cause a fire or
explosion.
Figure 6-1
A
A
B
B
Figure 6-2
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/