Graco ISPC054BA User manual

Instruction

Manual

ISPC054BA 06/03 US

Avoid injury or death -

Read and understand this manual!

TABLE OF CONTENTS

Important Information.....................................1

Warnings.......................................................2

Basic Information.............................................4

What is LATCH?...............................................5

LATCH System..................................................6

Vehicle Seat Belts........................................... 26

• Locking Clip........................................ 31

Additional Information ...................................32

• Tether Storage

• Cup Holder

• Body Pillow

• Care and Cleaning

• Aircraft Use

• Second Hand Child Restraint

Replacement Parts.........................................

38

Storage.....................................Back Cover

• Locking Clip

• Instruction Manual

Help Information.......................

Back Cover

Instruction manual is for:

• ComfortSport5-Point Newborn/Toddler Child Restraint

• ComfortSport Overhead Shield Newborn/Toddler

Child Restraint

Instructions for these models are the same unless

otherwise noted.

❃

Before You Begin

❃

Use

❃

Special Information

Height & Weight Limits....................................7

Rear-facing Installation With LATCH..................8

Forward-facing Installation With LATCH.........10

Rear-facing Installation With

Vehicle Seat Belts............................................

12

Forward-facing Installation With

Vehicle Seat Belts............................................

14

Placing Child in Child Restraint.......................16

Operations and Adjustments..........................18

• Harness Straps

• Harness Tie

• Buckle

• Recline / Upright Positions

• 5-Point Crotch Strap Adjustment

• Overhead Shield Adjustment

• Changing Harness Strap Slots

• LATCH Belt Routing

• Removing LATCH from Vehicle Anchor Points

• LATCH Storage

IMPORTANT INFORMATION

No child restraint can guarantee protection

from injury in every situation, but proper use

helps reduce the risk of serious injury or death.

READ THIS MANUAL CAREFULLY.

Child restraints could be recalled for safety

reasons. You must register this restraint

to be reached in a recall. Fill out the

registration card attached to child restraint and

mail today or send your name, address, and the

restraint’s model number and manufacturing

date to:

Graco Children’s Products, Inc.

150 Oaklands Blvd.

Exton, PA 19341

or call 1-800-345-4109

www.gracobaby.com

For recall information:

• Call the U.S Government’s Auto Safety

Hotline at 1-800-424-9393

(202-366-0123 in D.C. area)

• www.nhtsa.dot.gov

• Call Graco Children’s Products Inc. at

1-800-345-4109

www.gracobaby.com

✔ Read and understand instruction manual

and child restraint labels.

✔ Infants less than 20 lbs. (9 kg) must use

child restraint rear-facing.

✔ Do not use child restraint rear-facing in

vehicle seat with air bag.

✔ Secure children in rear seat of vehicle

whenever possible.

✔ Never leave child unattended.

✔ Install child restraint securely with vehicle seat

belt or LATCH belt.

✔ Do not use after date shown on back of

child restraint.

✔ Do not allow anyone (babysitter, relatives,

etc.) to use child restraint without first

understanding all instructions.

1

❃

Registration Information

❃

Safety First Check List

❃

LATCH

This child restraint may be installed in a vehicle

using either the vehicle seat belt or the

LATCH system (for vehicles equipped with

LATCH).

WARNINGS - Prevent serious injury or death:

Failure to follow these instructions

and child restraint labels can result

in child striking the vehicle’s interior

during a sudden stop or crash.

Secure child restraint with a vehicle

seat belt or LATCH that is properly

routed as shown in this manual.

Select a suitable location for the

child restraint in your vehicle.

Choose the correct mode of use for

the child restraint depending on

your child’s size. Infants less than

20 lbs. (9 kg) must use this child

restraint rear-facing. Serious

crippling injury or death can result

if infant faces front of vehicle. The

American Academy of Pediatrics

recommends that children should be

at least one year of age before being

positioned forward facing.

2

Vehicle seat belt system MUST hold

child restraint securely. Not all

vehicle seat belts can be used with

a child restraint.

If vehicle seat belt does not hold

child restraint securely, read

“Vehicle Seat Belts” section.

Never put a child restraint in a front

vehicle seat unless recommended

by vehicle owner’s manual.

National Highway Traffic Safety

Administration (NHTSA) alerts

vehicle owners that according to

accident statistics, children up to

age 12 are safer in the back seat.

For vehicles with air bags, refer to

vehicle owner’s manual for child

restraint installation information.

3

If child restraint is in a crash, it

must be replaced. DO NOT use it

again! A crash can cause unseen

damage and using it again could

result in serious injury or death.

DO NOT use child restraint if it is

damaged or missing parts.

DO NOT use accessories or parts

other than those provided by

Graco. Their use could alter the

performance of the child restraint.

Rear-facing child restraint must be

properly leveled:

• Too reclined can result in injury

or ejection.

• Too upright can result in

breathing difficulties.

Insert the harness straps in the

proper slots for your child. Never

leave child unattended, even when

sleeping. Child may become tangled

in harness straps and suffocate or

strangle.

DO NOT remove LATCH system from

child restraint. If using vehicle seat

belt to secure child restraint, LATCH

connectors must be stored. (see

section “LATCH storage”)

Never attach two

LATCH connectors

to one vehicle lower

anchor point unless

specifically allowed

by the vehicle

manufacturer.

WARNINGS - Prevent serious injury or death (continued):

BASIC INFORMATION

This child restraint meets or exceeds all

applicable requirements of Federal Motor

Vehicle Safety Standard 213 for use in motor

vehicles and aircraft.

Always secure child restraint with LATCH or a

vehicle seat belt, even when unoccupied.

In a crash, an unsecured child restraint can

injure passengers.

Protect vehicle seat. Use a child restraint mat,

towel or thin blanket under and behind child

restraint.

Child restraint parts can get very hot in the sun

or warm weather.

To avoid burns, always check before putting

child in child restraint.

4

Do not use child restraint on rear-facing or

side-facing vehicle seats.

❃

Certification

❃

Unoccupied Child Restraint

STOP using child restraint and throw it away

after the date molded into the back of

the child restraint.

Look for:

Do not use this car

seat after December

Year

❃

Child Restraint Useful Life

❃

Dangerous Vehicle Seats

❃

Vehicle Seat Protection

❃

Warm Weather

DO NOT place this

child restraint in

a vehicle seating

location that has a

front air bag. If an

air bag inflates, it

can hit the child and

child restraint with great force

and cause serious injury or death

to your child. Check vehicle owner’s

manual for information about

side air bags and child restraint

installation.

WARNING

5

Vehicle

Top Tether Anchor

Points

Vehicle

Lower Anchor

Points

Vehicle

Seat Crease

Typical seat in a

passenger vehicle.

Other vehicle types

may have different

LATCH locations.

United States Federal Motor Vehicle Safety

Standards have defined a new system for

installing child restraints in vehicles. The

system is called LATCH. LATCH stands for:

L

ower Anchorage and Tether for CHildren.

LATCH System for Vehicles:

LATCH in the vehicle consists of a top tether

anchor point and two lower anchor points.

Some vehicle owner manuals use the term

ISOFIX to identify the new child restraint

anchorage system. This child restraint with

LATCH can also be used in vehicle seating

positions equipped with ISOFIX.

Newer vehicles may have one or more seating

positions equipped with LATCH anchor points.

If vehicle is equipped with LATCH, the vehicle

lower anchor points may be visible at the vehicle

seat crease. If not visible, they may be marked

with a symbol (Fig. a) or a colored dot.

See your vehicle owner’s manual for exact

locations, anchor identification, and

requirements for use with a child restraint.

Check vehicle owner’s manual for vehicle top

tether anchor locations. They may be identified

using one of the anchor symbols (Fig. b or Fig. c).

(Fig. a)

(Fig. b)

(Fig. c)

WHAT IS LATCH?

6

LATCH System:

LATCH consists of a permanently attached

lower anchorage belt and a top tether strap

(Fig. a).

ONLY use LATCH in a seating

position recommended

by vehicle manufacturer.

Vehicle

Lower

Anchor

Points

Child Restraint

Lower Anchorage

Belt

(Fig. a)

LATCH SYSTEM

Child Restraint

Top Tether

Vehicle

Top Tether

Anchor

Point

Thank you for contacting

Graco. LATCH is defined

as anchorages 280mm

(11.02 inches) on center.

As a manufacturer, we do

not recommend using the

LATCH system in the center

position if it exceeds this

length. If you have further

questions regarding LATCH

usage, please contact

NHTSA at 1-800-326-4236

or www.nhtsa.dot.gov.

HEIGHT & WEIGHT LIMITS

A preterm infant or low birth weight infant may

be at special risk in a vehicle or aircraft.

According to the American Academy of

Pediatrics, these infants may suffer breathing

difficulties if improperly reclined in a child

restraint.

Graco advises that you have your physician or

hospital staff evaluate your infant and recommend

the proper child restraint or car bed before you

and your infant leave the hospital.

7

❃

Preterm or Low Birth Weight

Infants

❃

Outgrowing Child Restraint

Prevent serious injury or death:

• Top of child’s ears must be below top

edge of child restraint.

• Child’s shoulders MUST not be above

top harness slots.

WARNING

Rear-facing: 5 to 30 lbs. (2.2-13.6 kg)

• Infants who weigh less than 20 lbs.

(9 kg) MUST be rear-facing.

• Infants or toddlers 20 to 30 lbs.

(9 to 13.6 kg) may be rear-facing.

Forward-facing: 20 to 40 lbs. (9 to 18 kg)

• Toddlers 20 to 30 lbs. (9 to 13.6 kg)

who are capable of sitting upright

unassisted may be forward-facing

*

.

If unable to sit unassisted, use

rear-facing.

• Toddlers 30 to 40 lbs.

(13.6 to 18 kg) and up to

40 inches (101.6 cm) tall MUST

be forward-facing.

IMPORTANT: This child restraint is

certified for use rear-facing with children

up to 30 lbs. (13.6 kg). However, some

children approaching 30 lbs. (13.6 kg) may be

too tall to fit comfortably rear-facing. When

child can no longer comfortably fit and knees

remain bent, child should use car seat

forward-facing only if child is over 20 lbs.

(9 kg) and can sit upright unassisted.

*

The American Academy of Pediatrics

recommends that children should be at least one

year of age before being positioned forward facing.

Forward-facing

Rear-facing

40 lbs.

(18 kg)

5 lbs.

(2.2 kg)

30 lbs.

(13.6 kg)

20 lbs.

(9 kg)

LATCH belt must be routed through

opening in child restraint for rear-facing mode.

(see page 23, fig. k).

Belt must lay flat and not be twisted.

Adjust child restraint to recline position

(see pages 18 and 19, fig. b) and place

rear-facing on vehicle seat equipped with

LATCH anchors.

For ease of installation, extend LATCH belt

to its maximum length.

Hook connectors to vehicle lower anchors

(fig. a). Pull connectors to be sure they are

securely attached to the anchor points. (fig. b).

Press down firmly in center of child restraint

while pulling LATCH adjustment belt. (fig. c).

REAR-FACING INSTALLATION WITH LATCH

1

3

4

5

2

8

Pull front to back and left to right to check for

secure installation (fig. d).

Check that the lower anchorage belt stays

tight and does not slip from the tightened

position. If it does not stay tight, try another

seating position or contact Customer Service

(see back cover).

Check level indicator on child restraint.

Vehicle must be on level ground and child in

child restraint when checking level indicator.

Ball MUST be entirely in green zone (fig. e). If

necessary, place rolled towels under child

restraint, at vehicle seat crease, until entire ball

is in green zone. Then re-check level indicator.

DO NOT use tether rear-facing. Tether must

be stored (see “Tether Storage” page 32).

Periodically check that child restraint is

securely installed and properly leveled; adjust

if necessary.

6

7

(fig. b)

(fig. c)

Openings

Towels

9

REAR-FACING INSTALLATION WITH LATCH

(continued):

(fig. a)

LAPC0110A

(fig. e)

(fig. d)

Tether

LATCH

LATCH belt must be routed through

opening in child restraint for forward-facing

(see page 23, fig. l).

Belt must lay flat and not be twisted.

Adjust child restraint to upright position

(see pages 18 and 19, fig. b) and place

forward-facing on vehicle seat equipped

with LATCH anchors.

For ease of installation, extend LATCH belt

to its maximum length.

Hook connectors to vehicle lower anchors

(fig. a). Pull connectors to be sure they are

securely attached (fig. b).

Press down firmly in center of child restraint to

compress vehicle seat cushion while tightening

LATCH belt by pulling adjustment belt (fig. c).

Use your knee to press down in center of

child restraint (fig. c).

FORWARD-FACING INSTALLATION WITH LATCH

1

3

4

5

2

10

Pull front to back and left to right to check for

secure installation (fig. d).

Check that the lower anchorage belt stays

tight and does not slip from the tightened

position. If it does not stay tight, try another

seating position or contact Customer Service

(see back cover).

Attach tether strap hook (A) to anchor

hardware (B) and tighten adjustment belt to

remove any slack (fig. e).

Periodically check that child restraint is securely

installed; adjust if necessary.

6

7

Openings

(fig. b)

(fig. c)

11

FORWARD-FACING INSTALLATION WITH LATCH

(continued):

(fig. a)

(fig. e)

(fig. d)

(B)

(A)

Pull to

tighten

Tether

LATCH

Pull front to back and left to right to check for

secure installation (fig. b). Vehicle lap belt

MUST stay tight.

If not secure, see “Vehicle Seat Belts” page 26.

Check level indicator on child restraint.

Vehicle must be on level ground and child in

child restraint when checking level indicator.

Ball MUST be entirely in green zone (fig. c).

If necessary, place rolled towels under child

restraint, at vehicle seat crease, until entire ball

is in green zone. Then re-check level indicator.

DO NOT use tether rear-facing. Tether must

be stored (see “Tether Storage” page 32).

Periodically check that child restraint is

securely installed and properly leveled;

adjust if necessary.

Store LATCH see page 25, fig. q.

Adjust child restraint to recline position

(see page 18 and 19, fig. b) and place

rear-facing on vehicle seat.

Thread vehicle seat belt through openings and

buckle belt.

Press down firmly in center of child restraint to

compress vehicle seat cushion while tightening

vehicle seat belt (fig. a).

REAR-FACING INSTALLATION WITH VEHICLE SEAT BELTS

1

3

4

5

2

12

LATCH belt MUST be stored when

using vehicle seat belt to install child

restraint.

WARNING

6

REAR-FACING INSTALLATION WITH VEHICLE SEAT BELTS

(continued):

Openings

Towels

13

LAPC0110A

(fig. c)

(fig. a) (fig. b)

Tether

LATCH (stored)

Installation with

Lap belt only

Installation with

Lap/shoulder belt

Store LATCH see page 25, fig. r.

Adjust child restraint to upright position (see

pages 18 and 19, fig. b) and place

forward-facing on vehicle seat.

Lift seat pad flap (available on some models).

Thread vehicle seat belt through openings.

Buckle belt (fig. a).

Press down firmly in center of child restraint to

compress vehicle seat cushion while tightening

vehicle seat belt.

Use your knee to press down in center of

child restraint (fig. b).

FORWARD-FACING INSTALLATION WITH VEHICLE SEAT BELTS

1

2

3

4

14

LATCH belt MUST be stored when

using vehicle seat belt to install

child restraint.

WARNING

Pull front to back and left to right to check for

secure installation (fig. c). Vehicle lap belt

MUST stay tight.

If not secure, see “Vehicle Seat Belts” page 26.

Attach tether strap hook (A) to anchor

hardware (B) and tighten adjustment belt to

remove any slack (fig. d). If vehicle does not

have anchor points to attach tether hook,

tether hook should be stored, see “Tether

Storage”, page 32.

Periodically check that child restraint is securely

installed; adjust if necessary.

5

6

FORWARD-FACING INSTALLATION WITH VEHICLE SEAT BELTS

(continued):

(fig. a)

(fig. b) (fig. c)

Openings

Stand

15

(fig. d)

(B)

(A)

Pull to

tighten

LATCH (stored)

Tether

Installation with

Lap belt only

Installation with

Lap/shoulder belt

Check harness system:

• Rear-facing - 5-30 lbs (2.2-13.6 kg)

Harness straps must be

through bottom or middle

slots at or below shoulders.

• Forward-facing - 20-30 lbs (9-13.6 kg)

and are at least one year old.

Harness straps must be

through middle or top slots

at or above shoulders.

• Forward-facing - 30-40 lbs (13.6-18 kg)

Harness straps must be

through top slots only.

DO NOT use middle slots

for child over 30 lbs. (13.6 kg).

Place child in child restraint with child’s back flat

against back of child restraint.

Place harness straps over child’s shoulders and

insert tongue(s) into buckle.

Pull up on tongue(s) to be sure they are locked.

Close harness tie:

Position harness tie at arm pit level.

Adjust harness straps to be snug. A snug strap

should not allow any slack. It lies in a relatively

straight line without sagging. It does not press

on the child’s flesh or push the child’s body into

an unnatural position (fig. a).

Check that harness straps on chest and thighs

are snug.

A rolled towel can be used on each side to

support small children (fig. b). Be sure towels

do not interfere with harness system. Towels

should NOT be placed under child.

To prevent serious injury or death:

• Keep harness straps snug and

positioned on shoulders with harness

tie at arm pit level.

• Do not use strap covers, blankets,

cushions, or padding under harness

straps or child unless provided by Graco.

• Child should be dressed in clothing

that does not interfere with buckling

the harness.

1

2

3

4

5

16

PLACING CHILD IN CHILD RESTRAINT

WARNING

5-Point Models Only:

• Crotch strap must be in opening closest to

but not under child.

Overhead Shield Models Only:

• Harness tongue must be in opening

closest to but not under child.

17

2

3

5-Point

Models

Overhead

Shield

Models

(fig. a)

2

(fig. b)

PLACING CHILD IN CHILD RESTRAINT (continued)

4

OPERATIONS and ADJUSTMENTS

18

Recline / Upright Positions (fig. b):

Rear-facing - MUST use Recline position.

Forward-facing - MUST use Upright position

Upright Position: Rotate stand out and push

into child restraint (fig. b).

Recline Position: Pull stand out and rotate

into child restraint.

Harness straps MUST move freely. Make sure

harness straps are not pinched by recline stand.

5-Point Crotch Strap Adjustment (fig. c):

• From bottom of child restraint, pull crotch

strap clip out and remove clip from crotch

strap loop.

• From top of child restraint, pull crotch strap

out and thread through desired slot. Make

sure red button is facing away from child.

• From bottom of child restraint, re-attach clip

to crotch strap loop exactly as shown.

Overhead Shield Adjustment (fig. d):

• To adjust: Press button down and slide

shield to desired position closest to child.

Release button to lock shield into one of

multiple positions.

NOTE: Shield does not need to contact

child when in closest position; harness

system restrains child.

Harness Straps (fig. a):

• To tighten: Pull lower belt tab.

• To loosen: Pull and hold upper belt tab

while pulling shoulder harness straps.

Harness Tie:

• To open: Press tabs and pull apart.

• To close: Snap halves together. Make

sure harness tie is locked by pulling out

on each half.

Buckle:

MUST be in opening closest to but not under

child.

5-Point Models

• To buckle: Insert both tongues into

buckle. Pull up on tongues to be sure

they are locked.

• To unbuckle: Press red button and pull

tongues out of buckle.

Overhead Shield Models

• To buckle: Push tongue into opening.

Pull up on tongue to be sure it is locked.

• To unbuckle: Press red button, pull

tongue out of opening and lift shield

over top of child restraint.

1

2

4

3

5

6

Page is loading ...

Graco ISPC054BA User manual

Graco ISPC054BA User manual

in other languages

Related papers

Other documents