Desa Tech VN3000TB Owner's manual

Brand: Desa Tech

Model: VN3000TB

Category: Space heaters

Type: Owner's manual

This manual is also suitable for

VN1800TB

VN1800TB

VN3000TB

Save this manual for future reference.

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result

causing property damage, personal injury, or loss

of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by

a qualified installer, service agency, or the gas

supplier.

INFRARED VENT-FREE NATURAL GAS HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

WARNING: Improper in-

stallation, adjustment, al-

teration, service, or mainte-

nance can cause injury or

property damage. Refer to

this manual for correct in-

stallation and operational

procedures. For assis-

tance or additional infor-

mation consult a qualified

installer, service agency,

or the gas supplier.

WARNING: This is an

unvented gas-fired heater.

It uses air (oxygen) from

the room in which it is in-

stalled. Provisions for ad-

equate combustion and

ventilation air must be pro-

vided. Refer to

Air for Com-

bustion and Ventilation

page 4 of this manual.

This appliance may be installed in an aftermarket* manufactured (mobile) home, where not

prohibited by state or local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

104820

INFRARED NATURAL GAS HEATER

1. This appliance is only for use with the

type of gas indicated on the rating plate.

This appliance is not convertible for use

with other gases.

2. If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department

3. This heater shall not be installed in a

bedroom or bathroom.

4. Never install the heater

• in a recreational vehicle

• where curtains, furniture, clothing, or

other flammable objects are less than

36 inches from the front, top, or sides

of the heater

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

5. Before using furniture polish, wax, car-

pet cleaner, or similar products, turn

heater off. If heated, the vapors from

these products may create a white pow-

der residue within burner box or on

adjacent walls or furniture.

6. This heater needs fresh, outside air ven-

tilation to run properly. This heater has

an oxygen depletion sensor (ODS) pilot

light safety system. The ODS shuts

down the heater if not enough fresh air

is available. See Fresh Air for Combus-

tion and Ventilation, pages 4 through 6.

7. Keep all air openings in front and

bottom of heater clear and free of de-

bris. This will insure enough air for

proper combustion.

8. If heater shuts off, do not relight until

you provide fresh, outside air. If heater

keeps shutting off, have it serviced.

9. Do not run heater

• where flammable liquids or vapors

are used or stored

• under dusty conditions

10. Never place any objects on the heater.

SAFETY

INFORMATION

Carbon Monoxide Poisoning: Early

signs of carbon monoxide poisoning re-

semble the flu, with headaches, dizziness,

or nausea. If you have these signs, the heater

may not be working properly. Get fresh air

at once! Have heater serviced. Some people

are more affected by carbon monoxide than

others. These include pregnant women, per-

sons with heart or lung disease or anemia,

those under the influence of alcohol, and

those at high altitudes.

Natural Gas: Natural gas is odorless. An

odor-making agent is added to natural gas.

The odor helps you detect a natural gas leak.

However, the odor added to natural gas can

fade. Natural gas may be present even though

no odor exists.

Make certain you read and understand all

Warnings. Keep this manual for reference.

It is your guide to safe and proper operation

of this heater.

IMPORTANT: Read this Owner’s

Manual carefully and completely

before trying to assemble, oper-

ate, or service this heater. Im-

proper use of this heater can cause

serious injury or death from burns,

fire, explosion, electrical shock,

and carbon monoxide poisoning.

11. Surface of heater becomes very hot

when running heater. Keep children and

adults away from hot surface to avoid

burns or clothing ignition. Heater will

remain hot for a time after shut-down.

Allow surface to cool before touching.

12. Carefully supervise young children

when they are in same room with heater.

13. Make sure grill guard is in place be-

fore running heater.

14. Do not use heater if any part has been

under water. Immediately call a quali-

fied service technician to inspect the

room heater and to replace any part of

the control system and any gas control

which has been under water.

15. Turn off and unplug heater and let

cool before servicing. Only a quali-

fied service person should service and

repair heater.

16. Operating heater above elevations of

4,500 feet could cause pilot outage.

17. Keep combustible materials, gasoline,

and other flammable liquids and vapors

away from the appliance area.

WARNINGS

DANGER: Carbon monoxide

poisoning may lead to death!

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger

insert, or other accessory not

approved for use with this heater.

104820

OWNER’S MANUAL

PRODUCT

IDENTIFICATION

LOCAL CODES

Install and use heater with care. Follow all

local codes. In the absence of local codes, use

the latest edition of National Fuel Gas Code

ANS Z223.1, also known as NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Figure 1 - Vent-Free Natural Gas Heater (Model VN3000TB Shown)

Control Knob

PRODUCT

FEATURES

SAFETY DEVICE

This heater has a pilot with an Oxygen

Depletion Sensor Shutoff System (ODS).

The ODS/pilot is a required feature for vent-

free room heaters. The ODS/pilot shuts off

the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system

requires no matches, batteries, or other

sources to light heater.

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging ap-

plied to heater for shipment.

3. Check heater for any shipping damage.

If heater is damaged, promptly inform

dealer where you bought heater.

Grill

Guard

Burners

Piezo Ignitor

Heater

Cabinet

Front

Panel

104820

INFRARED NATURAL GAS HEATER

AIR FOR

COMBUSTION AND

VENTILATION

Today’s homes are built more energy effi-

cient than ever. New materials, increased

insulation, and new construction methods

help reduce heat loss in homes. Home owners

weather strip and caulk around windows and

doors to keep the cold air out and the warm air

in. During heating months, home owners

want their homes as airtight as possible.

While it is good to make your home energy

efficient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

PRODUCING ADEQUATE

VENTILATION

The following are excerpts from National

Fuel Gas Code. NFPA 54/ANS Z2233.1, Sec-

tion 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will

help you classify your space and provide

adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and win-

dows may provide enough fresh air for

combustion and ventilation. However, in

buildings of unusually tight construction,

you must provide additional fresh air.

Unusually tight construction is de-

fined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6 x 10

-11

per pa-sec-m

) or less with open-

ings gasketed or sealed

and

b. weather stripping has been

added on openable windows and

doors

and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors, be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tions for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See

Ventilation Air

From Outdoors

, page 6

If your home does not meet all of the

three criteria above, see

Determining

Fresh-Air Flow for Heater Location,

page 5

Confined and Unconfined Space

The National Fuel Gas Code ANS Z223.1

defines a confined space as a space whose

volume is less than 50 cubic feet per 1,000

Btu per hour (4.8 m

per kw) of the aggre-

gate input rating of all appliances installed

in that space and an unconfining space as a

space whose volume is not less than 50

cubic feet per 1,000 Btu per hour (4.8 m

per

kw) of the aggregate input rating of all

appliances installed in that space. Rooms

communicating directly with the space in

which the appliances are installed*, through

openings not furnished with doors, are con-

sidered a part of the unconfined space.

This heater shall not be installed in a con-

fined space or unusually tight construction

unless provisions are provided for adequate

combustion and ventilation air.

* Adjoining rooms are communicating only

if there are doorless passageways or ventila-

tion grills between them.

WARNING: This heater shall

not be installed in a confined space

or unusually tight construction

unless provisions are provided

for adequate combustion and ven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

104820

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between

the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = ____________________ cu. ft. (volume of space)

Example:

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)

Example:

2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater ________________ Btu/Hr

Gas water heater* ________________ Btu/Hr

Gas furnace ________________ Btu/Hr

Vented gas heater ________________ Btu/Hr

Gas fireplace logs ________________ Btu/Hr

Other gas appliances* + ________________ Btu/Hr

Total = ________________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

____________Btu/Hr (maximum the space can support)

____________Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space can support)

58,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

Continued

Example:

Gas water heater 40,000 Btu/Hr

Vent-free heater + 18,000 Btu/Hr

Total = 58,000 Btu/Hr

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space

or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of

the methods described in the

National Fuel Gas Code, ANS Z223.1,

or applicable local codes.

104820

INFRARED NATURAL GAS HEATER

Figure 3 - Ventilation Air from Outdoors

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connect these items directly to the outdoors

or spaces open to the outdoors. These spaces

include attics and crawl spaces. Follow the

National Fuel Gas Code NFPA 54/ANS

Z223.1, Section 5.3, Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

IMPORTANT:

Do not provide openings for

inlet or outlet air into attic if attic has a

thermostat-controlled power vent. Heated air

entering the attic will activate the power vent.

Outlet

Air

Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

AIR FOR

COMBUSTION AND

VENTILATION

Continued

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

VENTILATION AIR

Ventilation Air From Inside

Building

This fresh air would come from an adjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(see options 1 and 2, Figure 2). You can also

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

Figure 2 - Ventilation Air from Inside Building

WARNING: Rework work-

sheet, adding the space of the

adjoining unconfined space. The

combined spaces must have

enough fresh air to supply all

appliances in both spaces.

104820

OWNER’S MANUAL

INSTALLATION

WARNING ICON G 001

WARNING: A qualified ser-

vice person must install heater.

Follow all local codes.

CHECK GAS TYPE

Use only natural gas. If your gas supply is

not natural, do not install heater. Call dealer

where you bought heater for proper type

heater.

INSTALLATION ITEMS

Before installing heater, make sure you have

the items listed below.

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• manual shutoff valve *

• ground joint union

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

* An A.G.A. design-certified manual shutoff

valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Pur-

chase the optional A.G.A. design-certified

manual shutoff valve from your dealer. See

Accessories, page 22.

LOCATING HEATER

This heater is designed to be mounted on

a wall.

WARNING ICON G 001

WARNING: Maintain the mini-

mum clearances shown in Figure

4. If you can, provide greater clear-

ances from floor, ceiling, and

joining wall.

You can locate heater on floor, away from a

wall. An optional floor mounting stand is

needed. Purchase the floor mounting stand

from your dealer. See Accessories, page 22.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objects are less than 36 inches

from the front, top, or sides of

the heater

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

IMPORTANT:

Vent-free heaters add mois-

ture to the air. Although this is beneficial,

installing heater in rooms without enough

ventilation air may cause mildew to form from

too much moisture. See Fresh Air for Com-

bustion and Ventilation, pages 4 through 6.

Continued

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must be

at least 18 inches above floor

• locate heater where moving ve-

hicle will not hit it

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as to-

bacco smoke, aromatic candles,

cleaning fluids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls.

NOTICE: This heater is intended

for use as supplemental heat. Use

this heater along with your pri-

mary heating system. Do not in-

stall this heater as your primary

heat source. If you have a central

heating system, you may run

system’s circulating blower while

using heater . This will help circu-

late the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

For convenience and efficiency, install heater

• where there is easy access for operation,

inspection, and service

• in coldest part of room

An optional fan kit is available from your

dealer. See Accessories, page 22. If plan-

ning to use fan, locate heater near an electri-

cal outlet.

36"

FLOOR

CEILING

Minimum

Of Carpe

Combust

Minimum

From

Sides Of

Heater

Left

Side

Right

Side

Figure 4 - Mounting Clearances As Viewed

From Front of Heater

Minimum To

Top Surface

Of Carpeting,

Tile Or Other

Combustible

Material

104820

INFRARED NATURAL GAS HEATER

Methods For Attaching

Mounting Bracket To Wall

Only use last hole on each end of mounting

bracket to attach bracket to wall. These two

holes are 16 inches apart from their centers.

Attach mounting bracket to wall in one of

two ways.

1. Attaching to wall stud

2. Attaching to wall anchor

Attaching To Wall Stud: This method

provides the strongest hold. Insert mounting

screws through mounting bracket and into

wall studs.

Attaching To Wall Anchor: This method

allows you to attach mounting bracket to

hollow walls (wall areas between studs) or

to solid walls (concrete or masonry).

Decide which method better suits your needs.

Either method will provide a secure hold for

the mounting bracket.

Marking Screw Locations

1. Tape mounting bracket to wall where

heater will be located. Make sure

mounting bracket is level.

Model VN3000TB

Model VN1800TB

Figure 7 - Mounting Bracket Clearances

2. Mark screw locations on wall (see Fig-

ure 7).

Note:

Only mark last hole on each end

of mounting bracket. Insert mounting

screws through these holes only.

3. Remove tape and mounting bracket

from wall.

18 3/4"

Min.

13"

Min.

16"

Adjoining Wall

Only Insert Mounting

Screws Through Last

Hole On Each End

Floor

WARNING: Maintain minimum

clearances shown in Figure 7. If

you can, provide greater clear-

ances from floor and joining wall.

INSTALLING HEATER TO

WALL

Mounting Bracket

Locate mounting bracket in heater car-

ton. Remove mounting bracket from

heater carton.

Figure 6 - Removing Front Panel Of Heater

Removing Front Panel Of Heater

1. Remove two screws near bottom cor-

ners of front panel.

2. Lift straight up on grill guard until it stops.

Grill guard will slide up about 1/4".

3. Pull bottom of front panel forward,

then down.

Figure 5 - Mounting Bracket Location

Mounting

Bracket

INSTALLATION

Continued

16"

18 3/4"

Min.

9 1/4"

Min.

Adjoining Wall

Only Insert Mounting

Screws Through Last

Hole On Each End

Floor

104820

OWNER’S MANUAL

Installing Bottom Mounting

Screws

1. Locate two bottom mounting holes.

These holes are near bottom on back

panel of heater (see Figure 11).

2. Mark screw locations on wall.

3. Remove heater from mounting bracket.

4. If installing bottom mounting screws

into hollow or solid wall, install wall

anchors. Follow steps 1 through 4 un-

der Attaching To Wall Anchor Method.

If installing bottom mounting screw

into wall stud, drill holes at marked lo-

cations using 9/64" drill bit.

5. Replace heater onto mounting bracket.

6. Place spacers between bottom mount-

ing holes and wall anchor or drilled hole

(see Figure 11).

7. Hold spacer in place with one hand.

With other hand, insert mounting screw

through bottom mounting hole and

spacer. Place tip of screw in opening

of wall anchor or drilled hole.

8. Tighten both screws until heater is firmly

secured to wall. Do not over tighten.

Note:

Do not replace front panel at this

time. Replace front panel after making

gas connections and checking for leaks

(see pages 10 and 11).

Figure 9 - Popping Open Anchor Wings

For Thin Walls

Attaching Mounting Bracket To

Wall

Note:

Wall anchors, mounting screws, and

spacers are in hardware package. The hard-

ware package is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1. Drill holes at marked locations using

9/64" drill bit.

2. Place mounting bracket onto wall. Line

up last hole on each end of bracket with

holes drilled in wall.

3. Insert mounting screws through bracket

and into wall studs.

4. Tighten screws until mounting bracket

is firmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow

walls (wall areas between studs) or solid

walls (concrete or masonry)

1. Drill holes at marked locations using

5/16" drill bit. For solid walls (concrete

or masonry), drill at least 1" deep.

2. Fold wall anchor as shown in Figure 8.

3. Insert wall anchor (wings first) into

hole. Tap anchor flush to wall.

4. For thin walls (1/2" or less), insert red

key into wall anchor. Push red key to

“pop” open anchor wings.

IMPORTANT:

Do not hammer key!

For thick walls (over 1/2" thick) or solid

walls, do not pop open wings.

5. Place mounting bracket onto wall. Line

up last hole on each end of bracket with

wall anchors.

6. Insert mounting screws through bracket

and into wall anchors.

7. Tighten screws until mounting bracket

is firmly fastened to wall.

Placing Heater On Mounting

Bracket

1. Locate two horizontal slots on back

panel of heater.

2. Place heater onto mounting bracket.

Slide horizontal slots onto stand-out

tabs on mounting bracket.

Figure 8 - Folding Anchor

INSTALLATION

Continued

Figure 10 - Mounting Heater Onto

Mounting Bracket

Stand-Out Tab

Mounting Bracket

(attached to wall)

Horizontal Slots

Figure 11 - Installing Bottom Mounting

Screws

Continued

Screw

Spacer

Wall

104820

INFRARED NATURAL GAS HEATER

IMPORTANT:

Hold pressure regulator

with wrench when connecting it to gas pip-

ing and/or fittings.

Figure 12 - Gas Connection

* An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Purchase the optional A.G.A. design-certified manual

shutoff valve from your dealer. See Accessories, page 22.

Inlet Pipe From Gas

Meter (7" W.C. to

10.5" W.C. Pressure)

CONNECTING TO GAS

SUPPLY

WARNING: A qualified service

person must connect heater to

gas supply. Follow all local codes.

Typical Inlet Pipe Diameters

VN1800TB 3/8" or greater

VN3000TB 1/2" or greater

Installation must include a manual shutoff

valve, union, and plugged 1/8" NPT tap.

Locate NPT tap within reach for test gauge

hook up. NPT tap must be upstream from

heater (see Figure 12). An appliance main

gas valve (manual shutoff valve) shall be

provided in an accessible location for turning

on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male

threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe

could result in clogged heater valves.

Install sediment trap in supply line as shown

in Figure 12. Locate sediment trap where it

is within reach for cleaning. Locate sedi-

ment trap where trapped matter is not likely

to freeze. A sediment trap traps moisture

and contaminants. This keeps them from

going into heater controls. If sediment trap

is not installed or is installed wrong, heater

may not run properly.

CAUTION: Use pipe joint seal-

ant that is resistant to liquid pe-

troleum (LP) gas.

IMPORTANT:

Check gas line pressure be-

fore connecting heater to gas line. Gas line

pressure must be no greater than 14 inches

of water. If gas line pressure is higher,

heater regulator damage could occur.

WARNING: Never connect

heater to private (non-utility) gas

wells. This gas is commonly

known as well-head gas.

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of large

enough diameter to allow proper

gas volume to heater. If pipe is

too small, undue loss of pres-

sure will occur.

INSTALLATION

Continued

Tee Joint

Reducer

Bushing to

1/8" NPT

Plug Tap

Test

Gauge

Connection *

Sediment

Trap

Tee Joint

Pipe Nipple

Cap

Manual Shutoff Valve *

3/8" NPT

Pipe Nipple

Ground Joint

Union

Heater

Cabinet

3" Minimum

Pressure Regulator

104820

OWNER’S MANUAL

CHECKING GAS

CONNECTIONS

Pressure Testing Gas Supply

Piping System

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPA)

1. Disconnect heater and its individual

manual shutoff valve from gas supply

piping system. Pressures in excess of

1/2 PSIG will damage heater regulator.

2. Cap off open end of gas pipe where

manual shutoff valve was connected.

3. Pressurize supply piping system by

either using compressed air or open-

ing main gas valve located on or near

gas meter.

4. Check all joints of gas supply piping

system. Apply mixture of liquid soap

and water to gas joints. Bubbles form-

ing show a leak.

5. Correct all leaks at once.

6. Reconnect heater and manual shutoff

valve to gas supply. Check reconnected

fittings for leaks.

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPA)

1. Close manual shutoff valve (see

Figure 13).

2. Pressurize supply piping system by either

using compressed air or opening main gas

valve located on or near gas meter.

3. Check all joints from gas meter to manual

shutoff valve (see Figure 14). Apply mix-

ture of liquid soap and water to gas joints.

Bubbles forming show a leak.

4. Correct all leaks at once.

WARNING: Never use an open

flame to check for a leak. Apply a

mixture of liquid soap and water

to all joints. Bubbles forming

show a leak. Correct all leaks at

once.

WARNING: Test all gas pip-

ing and connections for leaks

after installing or servicing. Cor-

rect all leaks at once.

Pressure Testing Heater Gas

Connections

1. Open manual shutoff valve (see Figure 13).

2. Open main gas valve located on or near

gas meter.

3. Make sure control knob of heater is in

the OFF position.

4. Check all joints from manual shutoff

valve to control valve (see Figure 14).

Apply mixture of liquid soap and wa-

ter to gas joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater,

pages ll through 13). Check the rest of

the internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to

Appliance, page 12).

8. Replace front panel.

Figure 13 - Manual Shutoff Valve

Manual

Shutoff

Valve

Closed

Figure 14 - Checking Gas Joints

Manual

Shutoff

Valve

Gas Meter

Control Valve Location

Open

OPERATING

HEATER

FOR YOUR SAFETY

READ BEFORE

LIGHTING

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be

sure to smell next to the floor because

some gas is heavier than air and will

settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas sup-

plier, call the fire department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn

by hand, don’t try to repair it, call a

qualified service technician or gas

supplier. Force or attempted repair

may result in a fire or explosion.

D. Do not use this appliance if any part

has been under water. Immediately

call a qualified service technician

to inspect the appliance and to re-

place any part of the control sys-

tem and any gas control which has

been under water.

WARNING: If you do not fol-

low these instructions exactly, a

fire or explosion may result caus-

ing property damage, personal

injury or loss of life.

INSTALLATION

Continued

104820

INFRARED NATURAL GAS HEATER

TO TURN OFF GAS TO

APPLIANCE

Shutting Off Heater

1. Turn control knob clockwise

to the OFF position.

2. Turn off all electric power to the ap-

pliance if service is to be performed.

Shutting Off Burner Only (pilot

stays lit)

Turn control knob clockwise to

the PILOT position.

CAUTION: Do not try to adjust

heating levels by using the

manual shutoff valve.

OPERATING

HEATER

Continued

Ignitor Electrode

Pilot Burner

Thermocouple

Figure 16 - Pilot

IGNITOR

PILOT

OFF

LIGHTING

INSTRUCTIONS

Figure 15 - Control Knob In The OFF

Position

Control Knob

Ignitor Button

1. STOP! Read the safety information

on page 11, column 3.

2. Make sure manual shutoff valve is

fully open.

3. Turn control knob clockwise

to the OFF position.

4. Wait five (5) minutes to clear out any

gas. Then smell for gas, including

near the floor. If you smell gas,

STOP! Follow “B” in the safety in-

formation page 11, column 3. If you

don’t smell gas, go to the next step.

5. Turn control knob counterclockwise

to the PILOT position. Press

in control knob for five (5) seconds

(see Figure 15).

Note:

You may be running this

heater for the first time after hook-

ing up to gas supply. If so, the con-

trol knob may need to be pressed in

for 30 seconds. This will allow air to

bleed from the gas system.

• If control knob does not pop up

when released, contact a quali-

fied service person or gas sup-

plier for repairs.

6. With control knob pressed in, push

down and release ignitor button.

This will light pilot. The pilot is at-

tached to the front of burner. If

needed, keep pressing ignitor but-

ton until pilot lights.

Note:

If pilot does not stay lit, refer to

Troubleshooting, pages 14 through 16.

Also contact a qualified service person

or gas supplier for repairs. Until re-

pairs are made, light pilot with match.

To light pilot with match, see Manual

Lighting Procedure on page 13.

7. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob.

Note:

If pilot goes out, repeat steps

3 through 7. This heater has a safety

interlock system. Wait one (1) minute

before lighting pilot again.

8. Turn control knob counterclockwise

to desired heating level. The

main burner should light. Set control

knob to any heat level between HI

and LOW (see Figure 17).

THERMOSTAT

CONTROL

OPERATION

The thermostatic control used on these

models differs from standard thermostats.

Standard thermostats simply turn on and

off the burner. The thermostat used on

this heater senses the room temperature.

At times the room may exceed the set

temperature. If so, the burner will shut off.

The burner will cycle back on when room

temperature drops below the set tempera-

ture. The control knob can be set to any 2

comfort level between HI and LO.

Note:

The thermostat sensing bulb mea-

sures the temperature of air near the

heater cabinet. This may not always agree

with room temperature (depending on

housing construction, installation loca-

tion, room size, open air temperatures,

etc.) Frequent use of your heater will let

you determine your own comfort levels.

Figure 17 - Burner Patterns

OFF

PILOT

OFF

PILOT

Control Knob

VN1800TB

VN3000TB

104820

OWNER’S MANUAL

INSPECTING

BURNER

Check pilot flame pattern and burner flame

pattern often.

PILOT FLAME PATTERN

Figure 18 shows a correct pilot flame pattern.

Figure 19 shows an incorrect pilot flame

pattern. The incorrect pilot flame is not touch-

ing the thermocouple. This will cause the

thermocouple to cool. When the thermo-

couple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown

in Figure 19

• turn heater off (see To Turn Off Gas to

Appliance, page 12)

• see Troubleshooting, pages 14 through 16

GRH/OV 009GOOD PILOT

Figure 18 - Correct Pilot Flame Pattern

Thermocouple

GRH/OV 010BAD PILOT

Thermocouple

Figure 19 - Incorrect Pilot Flame Pattern

Pilot Burner

Figure 20 - Correct Burner Flame Pattern

Bad Burner Pattern-Plaque

GRH/OV 019

Figure 21 - Incorrect Burner Flame Pattern

BURNER FLAME PATTERN

Figure 20 shows a correct burner flame

pattern. Figure 21 shows an incorrect burner

flame pattern.

If pilot flame pattern is incorrect, as shown

in Figure 21

• turn heater off (see To Turn Off Gas to

Appliance, page 12)

• see Troubleshooting, pages 14 through 16

CLEANING AND

MAINTENANCE

ODS/PILOT AND BURNER

ORIFICE

• Use a vacuum cleaner, pressurized air, or

small, soft bristled brush to clean.

CLEANING BURNER

PILOT AIR INLET HOLE

We recommend that you clean the unit every

2,500 hours of operation or every three months.

We also recommend that you keep the burner

tube and pilot assembly clean and free of dust

and dirt. To clean these parts we recommend

using compressed air no greater than 30 PSI.

Your local computer store, hardware store, or

home center may carry compressed air in a

can. You can use a vacuum cleaner in the

blow position. If using compressed air in a

can, please follow the directions on the can. If

you don't follow directions on the can, you

could damage the pilot assembly.

1. Shut off the unit, including the pilot.

Allow the unit to cool for at least

thirty minutes.

2. Inspect burner, pilot for dust and dirt.

3. Blow air through the ports/slots and

holes in the burner.

Clean the pilot assembly also. A yellow tip

on the pilot flame indicates dust and dirt in

the pilot assembly. There is a small pilot air

inlet hole about two inches from where the

pilot flame comes out of the pilot assembly

(see Figure 23). With the unit off, lightly

blow air through the air inlet hole. You may

blow through a drinking straw if compressed

air is not available.

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized air

to clean.

Exterior

• Use a soft cloth dampened with a mild

soap and water mixture. Wipe the cabi-

net to remove dust.

CAUTION: You must keep

control areas, burner, and circu-

lating air passageways of heater

clean. Inspect these areas of

heater before each use. Have

heater inspected yearly by a quali-

fied service person. Heater may

need more frequent cleaning due

to excessive lint from carpeting,

pet hair, etc.

WARNING: Turn off heater

and let cool before cleaning.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 5 under Light-

ing Instructions on page 12.

2. With control knob pressed in, strike

match. Hold match to pilot until pi-

lot lights.

3. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob. Now

follow step 8 uner Lighting Instruc-

tions, page 12

OPERATING

HEATER

Continued

Figure 23 - Pilot Inlet Air Hole

Pilot Assembly

Pilot Air Inlet

Hole

104820

INFRARED NATURAL GAS HEATER

TROUBLESHOOTING

OBSERVED PROBLEM

When ignitor button is pressed in, there is no

spark at ODS/pilot

ODS/pilot lights but flame goes out when

control knob is released

POSSIBLE CAUSE

1. Ignitor electrode positioned wrong

2. Ignitor electrode broken

3. Ignitor electrode not connected to igni-

tor cable

4. Ignitor cable pinched or wet

5. Broken ignitor cable

6. Bad piezo ignitor

7. Piezo ignitor nut is loose

1. Gas supply turned off or manual shutoff

valve closed

2. Control knob not fully pressed in while

pressing ignitor button (non-thermostat

models only)

Thermostat control knob not fully

pressed in while pressing ignitor button

(thermostat models only)

3. Air in gas lines when installed

4. ODS/pilot is clogged

5. Gas regulator setting is not correct

6. Thermostat control knob not in pilot

position

REMEDY

1. Replace ignitor

2. Replace ignitor

3. Reconnect ignitor cable

4. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

5. Replace ignitor cable

6. Replace control valve (piezo is part of

control valve)

7. Tighten nut holding piezo ignitor. Nut

is located inside heater cabinet at top

1. Turn on gas supply or open manual

shutoff valve

2. Fully press in control knob while press-

ing ignitor button (non-thermostat mod-

els only)

Fully press in thermostat control knob

while pressing ignitor button (thermo-

stat models only)

3. Continue holding down control knob.

Repeat igniting operation until air is re-

moved

4. Clean ODS/pilot (see Cleaning and

Maintenance, page 13 ) or replace ODS/

pilot assembly

5. Replace gas regulator

6. Turn thermostat control knob to pilot

position

WARNING: Turn off and un-

plug heater and let cool before

servicing. Only a qualified ser-

vice person should service and

repair heater.

CAUTION: Never use a wire,

needle, or similar object to clean

ODS/pilot. This can damage ODS/

pilot unit.

www.desatech.com

Note:

For additional help, visit DESA

International’s Technical Service web

site at www.desatech.com.

Note:

All troubleshooting items are listed in

order of operation.

104820

OWNER’S MANUAL

OBSERVED PROBLEM

When ignitor button is pressed in, there is a

spark at ODS/pilot but no ignition

Burner(s) does not light after ODS/pilot is lit

Delayed ignition of burner(s)

Burner backfiring during combustion

Burner plaque(s) does not glow

Slight smoke or odor during initial operation

Heater produces a clicking/ticking noise

just after burner is lit or shut off

White powder residue forming within burner

box or on adjacent walls or furniture

TROUBLESHOOTING

Continued

REMEDY

1. Press in control knob fully

2. After ODS/pilot lights, keep control

knob pressed in 30 seconds

3. Fully open manual shut-off valve

4. Hand tighten until snug, then tighten

1/4 turn more

5. A) Contact local natural gas company

B) Clean ODS/pilot (see Cleaning and

Maintenance, page 13) or replace ODS/

pilot assembly

6. Replace thermocouple

7. Replace control valve

8. Wait one minute for safety interlock sys-

tem to reset. Repeat ignition operation

1. Clean burner orifice(s) (see Cleaning

and Maintenance, page 13) or replace

burner orifice(s)

2. Replace burner orifice(s)

3. Contact local natural gas company

1. Contact local natural gas company

2. Clean burner orifice(s) (see Cleaning

and Maintenance, page 13) or replace

burner orifice(s)

1. Clean burner orifice(s) (see Cleaning

and Maintenance, page 13) or replace

burner orifice(s)

2. Replace burner

3. Replace gas regulator

1. Replace burner

2. Contact local natural gas company.

3. Turn control knob until it locks at de-

sired setting

1. Problem will stop after a few hours of

operation

1. This is common with most heaters. If

noise is excessive, contact qualified ser-

vice person

1. Turn heater off when using furniture

polish, wax, carpet cleaners, or similar

products

POSSIBLE CAUSE

1. Control knob not fully pressed in

2. Control knob not pressed in long enough

3. Manual shutoff valve not fully open

4. Thermocouple connection loose at con-

trol valve

5. Pilot flame not touching thermocouple,

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

A) Low gas pressure

B) Dirty or partially clogged ODS/pilot

6. Thermocouple damaged

7. Control valve damaged

8. Safety interlock system has been trig-

gered (thermostat models only)

1. Burner orifice(s) is clogged

2. Burner orifice(s) diameter is too small

3. Inlet gas pressure is too low

1. Manifold pressure is too low

2. Burner orifice(s) is clogged

1. Burner orifice(s) is clogged or damaged

2. Burner damaged

3. Gas regulator defective

1. Plaque damaged

2. Inlet gas pressure is too low

3. Control knob set between locked

positions

1. Residues from manufacturing processes

1. Metal expanding while heating or con-

tracting while cooling

1. When heated, vapors from furniture pol-

ish, wax, carpet cleaners, etc. turn into

white powder residue

Continued

www.desatech.com

104820

INFRARED NATURAL GAS HEATER

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

POSSIBLE CAUSE

1. Heater burning vapors from paint, hair

spray, glues, etc. See

IMPORTANT

statement above

2. Gas leak. See Warning statement at

top of page

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Gas leak. See Warning statement at

top of page

2. Control valve defective

1. Foreign matter between control valve

and burner

2. Gas leak. See Warning statement at

top of page

1. Not enough combustion/ventilation air

OBSERVED PROBLEM

Heater produces unwanted odors

Heater shuts off in use (ODS operates)

Gas odor even when control knob is in OFF

position

Gas odor during combustion

Moisture/condensation noticed on windows

REMEDY

1. Ventilate room. Stop using odor caus-

ing products while heater is running

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 11)

1. Open window and/or door for ventilation.

2. Contact local natural gas company.

3. Clean ODS/pilot (see Cleaning and

Maintenance, page 13)

1. Locate and correct all leaks (see Check-

ing Gas Connections, page 11)

2. Replace control valve

1. Take apart gas tubing and remove for-

eign matter

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 11)

1. Refer to Fresh Air for Combustion and

Ventilation requirements (page 4)

IMPORTANT:

Operating heater where impurities in air exist may create odors. Cleaning

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,

etc., create fumes. These fumes may mix with combustion air and create odors.

www.desatech.com

104820

OWNER’S MANUAL

TECHNICAL

SERVICE

SPECIFICATIONS

VN1800TB VN3000TB

Btu 18,000 30,000

Type Gas Natural Only Natural Only

Ignition Piezo Piezo

Pressure Regulator Setting 6" W.C. 6" W.C.

Inlet Gas Pressure* (in. of water)

Maximum 10.5" 10.5"

Minimum 7" 7"

Dimensions, Inches (H x W x D)

Heater 23.5 x 18.5 x 8 23.5 x 25.9 x 8

Carton 25.8 x 21.3 x 10.1 25.8 x 28.7 x 10.1

Weight (pounds)

Heater 22 30

Shipping 27 36

Note

: Dimensions listed are outer most points on the heater (includes control knobs

and grill).

* For purposes of input adjustment.

SERVICE

PUBLICATIONS

You can purchase a service manual from the

address listed on the back page of this

manual. Send a check for $5.00 payable to

DESA International.

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burner(s) will have delayed ignition

• heater will not produce specified heat

When Gas Quality Is Bad

• pilot will not stay lit

• burner(s) will produce flames and soot

• heater will backfire when lit

You may feel your gas pressure is too low or

gas quality is bad. If so, contact your local

natural gas supplier.

REPLACEMENT

PARTS

Note:

Use only original replacement parts.

This will protect your warranty coverage for

parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealer from whom you

purchased this product. If they are unable to

supply original replacement part(s), call

DESA International’s Technical Service De-

partment at 1-800-323-5190 for information.

When contacting your dealer or DESA In-

ternational, have ready:

• your name

• your address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural gas)

• purchase date

Usually, we will ask you to return the defec-

tive part to the factory.

PARTS NOT UNDER

WARRANTY

Contact authorized dealers of this product.

If they can’t supply original replacement

part(s), call DESA International’s Parts

Department at 1-800-972-7879 for referral

information. When calling DESA Interna-

tional, have ready:

• model number of your heater

• the replacement part number

You may have further questions about in-

stallation, operation, or troubleshooting. If

so, contact DESA International’s Technical

Service Department at 1-800-323-5190.

You can also visit DESA International’s

Technical Service web site at

www.desatech.com.

104820

INFRARED NATURAL GAS HEATER

ILLUSTRATED

PARTS

BREAKDOWN

VN1800TB

BURNER ASSEMBLY

13-1

13-2

13-4

13-3

13-5

13-10

13-6

13-8

13-7

13-3

13-9

13-6

13-12

13-11

ODS/PILOT

104820

OWNER’S MANUAL

PARTS LIST

VN1800TB

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions

listed under Replacement Parts on page 17 of this manual.

KEY PART

NO. NUMBER DESCRIPTION QTY.

1 098304-01 Screw, #10 x 3/8" 2

2 098742-13 Front Panel 1

3 098238-06 Grill Guard 1

4 101108-01 Clip-Grill Guard 2

5 103843-02 Apron 1

6 M11084-26 Screw, #10 x 3/8" 9

7 098457-01 Reflector Assembly 1

8 098271-03 Ignitor Cable 1

9 099415-08 Regulator with Pressure Tap 1

10 098303-02 Screw, #6 x 3/8" 2

11 104617-10 Cabinet Assembly 1

12 097159-04 Piezo Ignitor, Snap-In 1

13 See Detail Burner Assembly 1

13-1 099218-06 Burner 1

13-2 099056-03 Injector-Plaque A 1

13-3 104818-01 Tubing-Valve to Burner 1

13-4 099056-24 Injector-Plaque B 1

13-5 M11084-37 Screw, #8 x 1/4" 2

13-6 099387-06 Pilot Tubing 1

13-7 103256-01 Inlet Tubing 1

13-8 103594-06 ODS/Pilot 1

13-9 098522-16 Control Valve 1

13-10 M11084-26 Screw, #10 x 3/8" 2

13-11 098514-01 Thermocouple 1

13-12 098594-01 Ignitor Electrode 1

14 099066-01 Mounting Bracket 1

15 104819-01 Regulator Bracket 1

PARTS AVAILABLE - NOT SHOWN

098305-01 Control Position Label 1

100642-01 Hardware Assembly 1

104820

INFRARED NATURAL GAS HEATER

ILLUSTRATED

PARTS

BREAKDOWN

VN3000TB

13-12

13-11

ODS/PILOT BURNER ASSEMBLY

13-1

13-4

13-2

13-5

13-3

13-8

13-4

13-6

13-9

13-10

13-7

13-5

Page is loading ...

Desa Tech VN3000TB Owner's manual

Brand: Desa Tech

Model: VN3000TB

Category: Space heaters

Type: Owner's manual

This manual is also suitable for

VN1800TB

Download PDF

report

Desa Tech VN3000TB Owner's manual

This manual is also suitable for

Desa Tech VN3000TB Owner's manual

Related papers

Other documents