Black & Decker GTC18504PC User manual

Brand: Black & Decker

Model: GTC18504PC

Category: Cordless hedge trimmers

Type: User manual

Black & Decker GTC18504PC is a powerful hedge trimmer designed for trimming hedges, shrubs, and brambles with ease. Featuring a 50 cm blade and a 1300 min-1 blade stroke rate, it delivers efficient and precise cutting performance. Its ergonomic design with a comfortable grip and lightweight construction ensures comfortable handling during extended use. Additionally, the safety features like the blade guard and the trigger switch with lock-off function provide enhanced safety while operating.

www.blackanddecker.com

English 4

繁體中文 10

32465

GTC18504PC

8 9

A B

0-15

I J

K L

ENGLISH

GTC18504PC

HEDGE TRIMMER

Technical data

GTC18504PC

Voltage

Blade

strokes

(no load)

min

-1

1300

Blade

length

Blade gap

mm 18

Weight

kg 2.4

Intended use

Your BLACK+DECKER

GTC18504PC hedge trimmer have

been designed for trimming hedges, shrubs and brambles.

This tool is intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric

shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains

operated (corded) power tool or battery operated (cordless)

power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply.

Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

ENGLISH

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. In

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

b. Use power tools only with specically designated

battery packs. Use of any other battery packs may create

a risk of injury and re.

c. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a re.

d. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, ush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for hedge

trimmers

u Keep all parts of the body away from the cutter blade.

Do not remove cut material or hold material to be cut

when blades are moving. Make sure the switch is off

when clearing jammed material. A moment of inattention

while operating the tool can result in serious personal

injury.

u Carry the hedge trimmer by the handle with the cutter

blade stopped. When transporting or storing the

hedge trimmer always t the cutting device cover.

Proper handling of the hedge trimmer will reduce possible

personal injury from the cutter blades.

u Hold the power tool by insulated gripping surfaces

only, because the cutter blade may contact hidden

wiring. Cutter blades contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give

the operator an electric shock.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those

recommended in this instruction manual can present a risk

of personal injury and/or damage to property.

u Do not carry the tool with your hands on the front handle,

switch or the trigger switch unless the battery has been

removed.

u If you have not used a hedge trimmer before, preferably

seek practical instruction by an experienced user in

addition to studying this manual.

u Never touch the blades while the tool is running.

u Never attempt to force the blades to come to a standstill.

u Do not put the tool down until the blades have come to a

complete standstill.

u Regularly check the blades for damage and wear. Do not

use the tool when the blades are damaged.

u Take care to avoid hard objects (e.g. metal wire, railings)

when trimming. Should you accidentally hit any such

object, immediately switch the tool off and check for any

damage.

u Should the tool start to vibrate abnormally, immediately

switch it off and remove the battery then check for any

damage.

u If the tool stalls, immediately switch it off. Remove the

battery before attempting to remove any obstructions.

u After use, place the blade sheath supplied over the

blades. Store the tool, making sure that the blade is not

exposed.

ENGLISH

u Always ensure that all guards are tted when using the

tool. Never attempt to use an incomplete tool or a tool with

unauthorised modications.

u Never allow children to use the tool.

u Be aware of falling debris when cutting the higher sides of

a hedge.

u Always hold the tool with both hands and by the handles

provided.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Labels on tool

The following pictograms are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Wear safety glasses or goggles when

operating this tool.

Wear ear protection when operating this tool.

Do not expose the tool to rain or high humidity.

Electrical safety

Additional safety instructions for batteries and

chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not store in locations where the temperature may

exceed 40 °C.

u Charge only at ambient temperatures between 10 °C and

40 °C.

u Charge only using the charger provided with the tool.

u When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

Do not attempt to charge damaged batteries.

Chargers

u Use your BLACK+DECKER charger only to charge

the battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Trigger switch

2. Lock off button

3. Switch handle

4. POWERCOMMAND button

5. Blade guard

ENGLISH

6. Bail handle

7. Blade

8. Battery (not include)

9. Charger (not include)

Assembly

Warning! Before assembly, remove the battery from the tool

t the blade sheath over the blades.

Warning! Before assembly, make sure that the tool is

switched off and unplugged and that the blade sheath is tted

over the blades.

Warning! Never use the tool without the guard.

Charging procedure

Black+decker chargers are designed to charge Black+decker

battery packs.

u Plug the charger into an appropriate outlet before inserting

the battery pack.

u Insert the battery pack into the charger as shown in

gure A.

u The green LED will ash indicating that the battery is

being charged.

u The completion of charge is indicated by the green LED

remaining on continuously. The pack is fully charged and

may be used at this time or left on the charger.

Note: Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished. For longest

battery life, do not discharge batteries fully. It is recommended

that the batteries be recharged after each use.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance.

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger. Never

attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a

service center for recycling.

Installing and removing the battery pack from the

tool

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack

u Insert battery (8) into tool until an audible click is heard

(Figure. B)

u Ensure battery pack is fully seated and fully latched into

position.

To remove battery pack

u Depress the battery release button as shown in gure C

and pull battery pack out of tool.

Assembly instructions

Warning! Make certain the battery is removed before

assembly or disassembly of any parts.

Assembly tools required (not supplied):- phillips

screwdriver.

Attaching guard and bail handle to trimmer

Warning! Only use with handle and guard properly assembled

to hedge trimmer. The use of the hedge trimmer without

the proper guard or handle provided may result in serious

personal injury.

ENGLISH

The trimmer is shipped with the guard and bail handle

attached with a plastic zip tie.

To assemble to trimmer:

u Cut the plastic zip tie.

u Remove the six screws that are partially run into the

trimmer housing (Figure D).

u Slide the guard (5) onto the front of the trimmer housing

as shown in gure E

u Insert two of the six screws into the openings on the sides

of the guard and tighten securely.

u Slide the bail handle (6) onto the front of the trimmer

housing behind the guard as shown in gure F.

u Insert the remaining four screws into the openings on the

sides of the bail handle and tighten securely.

Operation

u To turn the unit on, push the lock off button (2) down,

squeeze the trigger (1), as shown in gure G. Once

the unit is running, you may release the lock-off button.

In order to keep the unit running you must continue to

squeeze the trigger.

u To turn the unit off, release the trigger.

Warning! Never attempt to lock a switch in the on position.

Trimming Instructions

u Maintain proper footing and balance and do not overreach.

Wear safety goggles, non-skid footwear when trimming.

Hold the unit rmly in both hands and turn the unit ON.

Always hold the trimmer, as shown in the illustrations in

this manual, with one hand on the switch handle and one

hand on the bail handle (gure H). Never hold the unit by

the blade guard.

Trimming new growth (Fig. I)

u A wide, sweeping motion, feeding the blade teeth through

the twigs is most effective. A slight downward tilt of the

blade, in the direction of motion gives the best cutting.

Warning! Do not cut stems greater than 19mm.

Use the trimmer only for cutting normal shrubbery around

houses and buildings.

Level hedges (Fig. J)

u To obtain exceptionally level hedges a piece of string can

be stretched along the length of the hedge as a guide.

Side trimming hedges (Fig. K)

u Hold the trimmer as shown and begin at the bottom and

sweep up.

POWERCOMMAND

If you encounter a jam, depress the POWERCOMMAND

button (4) shown in gure l. The blades will move back and

forth in a slower, more forceful rhythm to help cut through

difcult branches. Release the button to return to normal

hedge trimming usage.

Note: Once the button is released, the blades will immediately

return to full speed.

Note: The blades will stop when the button is held for 15

seconds. To reengage the POWERCOMMAND feature,

release the button and depress it again. DO NOT continuously

hold the POWERCOMMAND button during normal hedge

trimming.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u After use, carefully clean the blades. After cleaning, apply

a lm of light machine oil to prevent the blades from

rusting.

The cutting blades are made from high quality, hardened steel

and with normal usage, they will not require resharpening.

However, if you accidentally hit a wire fence, stones, glass or

other hard objects, you may put a nick in the blade. There is

no need to remove this nick as long as it does not interfere

with the movement of the blade.

If it does interfere, remove the battery and use a ne toothed

le or sharpening stone to remove the nick. If you drop the

trimmer, carefully inspect it for damage. If the blade is bent,

housing cracked, or handles broken or if you see any other

condition that may affect the trimmer’s operation contact your

local BLACK+DECKER Service Center for repairs before

putting it back into use. Fertilizers and other garden chemicals

contain agents which greatly accelerate the corrosion of

metals. Do not store the unit on or adjacent to fertilizers or

chemicals. With the battery removed, use only mild soap and

a damp cloth to clean the unit. Never let any liquid get inside

the unit; never immerse any part of the unit into a liquid.

Prevent the blades from rusting by applying a lm of light

machine oil after cleaning.

ENGLISH

Troubleshooting

Problem Possible Cause Possible Solution

Slow running,

noisy or hot

blades.

Dry, corroded blades. Lubricate blades.

Blade or blade support bent. Straighten blade or blade support.

Bent or damaged teeth. Straighten teeth.

Loose blade bolts. Tighten blade bolts.

Unit will not

start.

Battery not installed properly. Check battery installation.

Battery not charged. Check battery charging requirements.

Lock off not fully operated. Check lock off is fully depressed prior to moving main trigger.

Battery won't

charge

Battery not inserted into charger. Insert battery into charger until green LED appears. Charge up

to 8 hours if battery totally drained.

Charger not plugged in. Plug charger into a working outlet. Refer to “Important Charging

Notes” for more details. Check current at receptacle by plugging

in a lamp or other appliance. Check to see if receptacle is

connected to a light switch which turns power off when you turn

out the light.

Surrounding air temperature too hot or

too cold.

Move charger and tool to a surrounding air temperature of above

40 degree F (4.5°C) or below 105 degree F (+40.5°C).

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Products and batteries contain materials that can be

recovered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries according to

local provisions.

Service Information

BLACK+DECKER offers a full network of company-owned and

authorized service locations throughtout Asia. All

BLACK+DECKER Service Centers are staffed with trained

personnel to provide customers with efcient and reliable

product service.

Whether you need technical advice, repair, or genuine factory

replacement parts, contact the BLACK+DECKER location

nearest to you.

Note

u BLACK+DECKER's policy is one of continuous

improvement to our products and, as such, we reserve the

right to change product specications without prior notice.

u Standard equipment and accessories may vary by country.

u Product specications may differ by country.

u Complete product range may not be available in all

countries. Contact your local BLACK+DECKER dealers for

range availability.

繁體中文

GTC18504PC

樹籬修剪機（籬笆剪）

技術資料

GTC18504PC

電壓

伏特

直流

刀片行程

(無負載)

轉/分

1300

刀片長度

公分

刀片間隙

公釐

重量

Kg 2.4

警告！本機不適用於直徑大於 18mm 的樹枝。

請注意！各地區上市產品/配件不盡相同，請依台灣繁

體中文說明書的內容為主。

Warning! Attachments and accessories are not the

same in each region, please only refer to Taiwan

Traditional Chinese description in this manual.

設計用途

您的 BLACK+DECKER

GTC18504PC 樹籬修剪機

設計用於對樹籬、灌木與荊棘進行修剪。本工具僅供

一般消費者 DIY 家庭使用，營業使用者不適用百得一

年保修條款。

安全說明

電動工具一般安全警告

警告！請閱讀安全警告及所有指示。不遵

循下列的這些警告和指示可能會導致觸

電、火災及 / 或嚴重傷害。

請妥善保存所有的警告和使用手冊以備將來查閱。

警告中的名詞「電動工具」是指電源驅動（插電）

電動工具，或者電池驅動（充電）電動工具。

1. 工作場地安全

a. 保持工作場地清潔明亮。混亂或黑暗的場地會引

發事故。

b. 請勿在易爆環境，如有易燃液體、氣體或粉塵的

環境中操作電動工具。電動工具產生的火花會點

燃粉塵或氣體。

c. 請等待兒童和旁觀者離開之後才操縱電動工具。

分心會導致您疏於控制。

2. 電氣安全

a. 電動工具插頭必須與插座相符。切勿以任何方式

改裝插頭。需接地的電動工具不能使用任何配接

器插頭。未經改裝的插頭和相符的插座可以減少

觸電危險。

b. 避免人體接觸接地表面，如管道、散熱片、爐灶和

冰箱。若您的身體接地，可增加觸電危險。

c. 請勿將電動工具暴露在雨中或潮濕環境中。水進

入電動工具會增加觸電危險。

d. 切勿濫用電線。請勿使用電線來搬運、拉動電動

工具或拔出插頭。讓電線遠離熱、油、銳邊和活動

部件。受損或纏繞的電線可增加觸電危險。

e. 若要在戶外使用電動工具，請使用適合戶外使用

的延長電纜。使用適合戶外使用的電線可減少觸

電危險。

f. 若必須在潮濕場合使用電動工具，請使用漏電保

護器 (RCD)。使用 RCD 可降低觸電危險。

3. 人身安全

a. 保持警覺；在操作電動工具時，請留意所執行的

操作並按照一般的常識執行。請勿在疲倦，或受

到藥物、酒精或治療的影響下操作電動工具。

操作電動工具期間注意力分散會導致嚴重人身

傷害。

b. 使用個人防護裝置。始終佩戴護目裝備。防護

裝置，例如在適當條件下可使用的防塵面具、

防滑安全鞋、安全帽或聽力保護等裝置可減少

人身傷害。

c. 避免意外啟動。連接電源及/或電池組、撿取或搬

運電動工具之前，請確定開關處於關閉位置。搬

運電動工具時若將手指放在開關上，或是在接通

開關電源時插入插頭都會引發危險。

d. 接通電動工具之前，請卸下所有的調整鑰匙或

扳手。遺留在電動工具旋轉部件上的扳手或鑰匙

會導致人身傷害。

e. 不要過度伸張雙手。時刻注意腳下和身體的平衡。

如此即可在發生意外的情況下更好地控制電動

工具。

f. 適當穿著。請勿穿寬鬆衣服或佩戴飾品。讓您的頭

髮、衣服和手套遠離活動部件。寬鬆衣服、佩飾和

長髮可能會捲入活動部件。

g. 若配備用於連接排屑裝置、集塵設備的裝置，請確

定正確連接和使用這些裝置。使用集塵設備可減

少與粉塵有關的危險。

4. 電動工具的使用與注意事項

a. 請勿超負荷使用電動工具。根據您的用途使用適

當的電動工具。使用適當的電動工具在其設計可

負荷的應用內，會讓您更有效、更安全地執行工作。

b. 若開關不能開啟或關閉電源，切勿使用該電動

工具。不能用開關來控制的電動工具將存在危險，

必須進行維修。

c. 在執行任何調整、更換配件或儲存電動工具之

前，必須從電源上拔掉插頭及/或卸下電池組。這

類防護性措施可降低電動工具意外啟動的風險。

d. 請將閒置的電動工具儲存在兒童無法接觸的地

方，並且勿讓不熟悉電動工具或對這些說明不瞭

繁體中文

解的人員操作電動工具。電動工具在未經培訓的

使用者手中會發生危險。

e. 維護電動工具。檢查活動部件是否對準或卡住、

是否存在任何破損情況，或任何能影響電動工具

運行的其他情況。若有損毀，必須在使用之前修理

電動工具。許多事故都是由於電動工具欠缺維護

所導致。

f. 保持刀具鋒利和清潔。妥善維護、切削鋒利的切

割工具不會輕易卡住並可更輕鬆控制。

g. 在使用電動工具、配件及刀頭等部件時，請遵循上

述指示，並將工作條件與要執行的工作考慮在內。

不按照設計目的使用電動工具將會導致危險。

5. 電池工具的使用與注意事項

a. 只能使用製造商指定的充電器為電池充電。使用

僅適合一種電池組的充電器為其他類型的電池組

充電會導致火災風險。

b. 請使用原廠的電動工具電池組。使用任何其他非

原廠的電池組會導致人身傷害和火災危險。

c. 不使用電池組時，請將其遠離迴紋針、硬幣、鑰匙、

釘子、螺釘等所有可連通電池兩極的金屬物品。

將電池兩極短路會導致灼傷或火災。

d. 濫用電池的情況下，液體會從電池中噴出；避免

與液體接觸。若不小心接觸液體，請用清水沖洗。

若液體噴濺到眼睛上，沖洗之後還要進行治療。

從電池噴出的液體會刺激皮膚或造成灼傷。

6. 維修

a. 電動工具之修理，僅可由認證的技術人員執行。

請勿交由非百得認證服務中心的技術人員進行修

理、維護、調整。若產品經由非百得認證的維修工

程師拆解、組裝、調整，恕無法適用百得一年家用

保修條款。為充份發揮其功能，修理、維護、調整

請務必使用原廠零件。百得認證服務中心擁有保

修條款解釋權。

電動工具之附加安全警告

警告！樹籬修剪機之附加安全警告

 請讓身體的所有部位遠離切割刀片。刀片運動時，

請勿移走切割材料或抓住要切割的材料。清除擁

塞的材料時，請確保開關已關閉。操作工具期間

注意力分散可能會導致嚴重人身傷害。

 手持樹籬修剪機時，請在切割刀片停止的狀況下

握住手柄。運送或存放樹籬修剪機時，請務必裝

好切割裝置的護蓋。正確握持樹籬修剪機會減輕

切割刀片可能產生的人身傷害。

 請僅從絕緣手柄表面握住電動工具，因為切割

刀片可能會接觸到隱藏的電線。若切割刀片接

觸到「帶電」導線，電動工具裸露的金屬部件可

能會「帶電」，從而導致操作人員觸電。

 本使用手冊對器具的設計用途進行了描述。使用

非本使用手冊所建議的任何其他配件或附件，或

使用本工具執行非本使用手冊中所建議的任何其

他操作，可導致人身傷害及/或財產損失的風險。

 除非電池已取出，否則在搬運工具時請勿將手放

在前手柄、開關或觸發開關上。

 若您此前從未使用過樹籬修剪機，除了詳閱本手

冊外，最好是請有經驗的使用者提供實踐說明。

 在工具運轉時切勿觸碰刀片。

 切勿嘗試強制刀片變為靜止狀態。

 除非刀片已完全靜止，否則請勿放下工具。

 定期檢查刀片是否有損壞及磨損。若刀片有損壞，

請勿使用本工具。

 在修剪樹籬時請小心，避免觸及硬物（例如金屬

線、欄杆）。若不慎觸及此類任何物件，請立即關

閉工具，並檢查工具是否有損壞。

 若工具開始異常震動，請立即關閉工具並取出

電池，然後檢查工具是否有損壞。

 若工具失速，請立即將其關閉。應先取出電池，

然後再嘗試清除任何障礙。

 使用後，請將提供的刀片護套套在刀片上。存放工

具時，請確保刀片並未暴露在外。

 使用工具時，請務必確保裝配所有保護裝置。

切勿嘗試使用不完備的工具或經過未授權變更的

工具。

 切勿讓兒童使用工具。

 切割較高的樹籬時，請小心落下的碎屑。

 握持工具時，請務必以雙手握住提供的手柄。

他人的安全

 生理、感覺或心理機能不健全的人員（包括兒童）

或缺乏經驗及知識的人員，除非由負責其安全的

人員提供有關使用此器具的監督或指示，否則不

得使用本工具。

 應該對兒童予以監督，以確保他們不會玩耍本

工具。

剩餘風險

使用工具時可能會出現未包括於隨附安全警告中的

其他剩餘風險。濫用、長時間使用等也會導致這些

風險。

即使應用有關的安全規定並採用安全裝置，仍然還有

一些無法避免的剩餘風險。這些風險包括：

 接觸旋轉/活動部件引起的傷害。

 更換任何部件、刀片或配件引起的傷害。

 長時間使用工具引起的傷害。若長時間使用工具，

請確保定時休息。

 聽力受損。

 吸入使用工具時產生的粉塵引起的健康危害

(譬如：在木材上使用時，尤其是櫟木、山毛櫸和中

密度纖維板 (MDF)。)

繁體中文

工具上的標籤

工具上顯示以下圖示與日期代碼：

警告！為了降低受傷的風險，使用者必須

仔細閱讀使用手冊。

操作本工具時，請佩戴安全護目鏡或防

護眼鏡。

製造年份及號碼（範例）

2016

23 BM

西元年份週數號碼

操作本工具時請佩戴聽力保護器。

請勿將工具暴露在雨中或高濕度環境中。

電氣安全

電池和充電器之附加安全指示

電池

 無論什麼原因，都不要嘗試打開電池。

 請勿將電池暴露在水中。

 不要將電池儲存在溫度可能超過 40 °C 的地方。

 只在環境溫度介於 10 °C 到 40 °C 之間的情況下

充電。

 只能使用本工具隨附的充電器為電池充電。

 處置電池時，請遵循「保護環境」部分提供的指

示執行。

切勿試圖為損毀的電池充電。

充電器

 只能使用工具隨附的 BLACK+DECKER 充電器為

工具內的電池充電。其他非原廠電池可能會爆裂，

導致人身傷害和損害。

 切勿嘗試為不可再充電的電池充電。

 立即更換損壞的電線。

 請勿將充電器暴露在水中。

 請勿打開充電器。

 請勿刺破充電器。

本充電器僅供室內使用。

使用之前請閱讀使用手冊。

您的充電器採用雙重絕緣，因此不需要使

用接地線。請務必檢查主電壓是否與銘牌

一致。切勿嘗試使用一般的電源插頭取代

充電器裝置。

 若電源線損壞，必須送往製造廠商或授權的

BLACK+DECKER 維修中心更換以避免發生

危險。

功能部件

本工具包括以下部分或全部功能部件。

 1.觸發開關

 2.安全按鈕

 3.開關手柄

 4.卡枝排除按鈕

 5.刀片防護罩

 6.弓形輔助手柄

 7.刀片

 8. 電池（需另購）

 9. 充電器（需另購）

組裝

警告！組裝之前，請卸下工具內的電池並將刀片護套

套在刀片上。

警告！組裝之前，請確定已關閉工具電源和拔出插

頭，並且已將刀片護套套在刀片上。

警告！使用本工具時，一定要使用防護罩。

充電程序

Black+decker 充電器專用於為 Black+decker 電池組

充電。

 放進電池組前，先將充電器的插頭插到適當的

插座。

 將電池組插入充電器，如圖 A 所示。

 綠色 LED 燈將會閃爍，指示電池正在充電。

 當綠色 LED 燈持續亮起時，代表充電完成。這個

時候，電池組的電力全滿，可以立即使用或是留在

充電器裡。

1. 在電池用完電量後，建議馬上充電，鋰電池請勿過

度放電，電力過度耗竭會導致鋰電池損壞。

2. 請將電池從機身卸下分開存放, 若長時間未使用

電池 (1 年以上)，請每 6 個月為電池充電一次，

以確保電池壽命。

3. 當主機突然停止動作，或無法輕鬆完成以往的作業

量時，請馬上充電。

將電池留在充電器中

充電器和電池組可以在 LED 亮起的情況下無限期地

保持連接。充電器會讓電池組保持充滿電量的狀態。

重要充電說明

 在空氣溫度介於 65 °F 至 75 °F (18 °- 24 °C) 之

間的環境中對電池組充電可以達到最長的使用

壽命和最佳的效能。請勿在空氣溫度低於 +40 °F

(+4.5 °C) 或高於 +105 °F (+40.5 °C) 的環境中對

電池組充電。這很重要，可以防止對電池組造成

嚴重損壞。

繁體中文

 充電器和電池組在充電時可能會變熱。這是正常

現象，並不代表出現任何問題。使用後，為了加速

電池組冷卻，請不要將充電器或電池組置於高溫

環境中，例如金屬貨棚或非絕緣的拖車。

 如果電池組沒有正常充電：

 在插座中插入燈具或其他電器的插頭，以檢查

插座中是否有電流。

 檢查插座是否與燈具開關相連接，如果連接，

燈具開關在關閉燈具時會切斷電源。

 將充電器和電池組移至空氣溫度約為 65 °F

- 75 °F (18 - 24 °C)

的環境中。

 如果問題仍然存在，請將工具、電池組和充電器

送到當地的維修中心。

 當電池組無法像從前一樣為作業輕鬆提供足夠的

電量時，應該對其充電。在此類情況下請勿繼續

使用。請按充電程序進行充電。如有需要，您還可

對還有餘電的電池組進行充電，這對電池組不會

有任何不良影響。

 導電的異物，包括但不限於鋼絲絨、鋁箔紙或任

何由金屬粒子組成的物件，必須要遠離充電器

範圍。充電器裡沒有電池組時，一定要拔掉充電

器的電源。請先拔掉電源插頭後再清潔充電器。

 切勿冷凍充電器，或將充電器浸在水中或任何其

他液體中。

警告！切勿讓任何液體進入充電器，不論是因為任何

理由，都不要嘗試打開電池。如果電池組的塑膠外殼

破損或裂開，請送回服務中心進行回收。

電池組安裝與拆卸

警告！卸下或安裝電池組之前，請確保安全按鈕已

接合，以防止開關啟動。

安裝電池組

 將電池 (8) 插入工具直到聽到卡嗒聲（圖 B）

 確保放好電池組並完全鎖定到位。

移除電池組

 如圖 C 所示，按下電池釋放按鈕並從工具中取下

電池組。

組裝指示

警告！在組裝或卸下任何部件前，請確定電池已取下。

需要使用的組裝工具（需另購）：

- 十字螺絲起子。

安裝防護罩和弓形輔助手柄到修剪機

警告！請僅在已正確地組裝手柄和防護罩的情況下

操作本樹籬修剪機。在未有正確地組裝防護罩和手

柄的情況下操作本樹籬修剪機，可能會導致嚴重人

身傷害。

本修剪機隨防護罩和弓形輔助手柄一同運送，並用塑

料紮帶固定。

組裝到修剪機：

 剪斷塑料紮帶。

 移除尚未完全旋入修剪機外罩的六顆螺絲

(圖 D)。

 如圖 E 所示，將防護罩 (5) 滑入修剪機外罩的前端

 將六顆螺絲的其中兩顆插入防護罩兩側的槽中，

並牢固擰緊。

 如圖 F 所示，將弓形輔助手柄 (6) 滑入修剪機外罩

的前端（防護罩的後方）。

 將餘下的四顆螺絲插入弓形輔助手柄兩側的槽中，

並牢固擰緊。

操作

 若要啟動裝置，請如圖 G 所示般將安全按鈕 (2)

向下推，並擠壓觸發開關 (1)。本裝置工作後，您便

可釋放安全按鈕。如需持續使用裝置，您必須保

持擠壓觸發開關。

 若要關閉裝置，請鬆開觸發開關。

警告！切勿嘗試將開關鎖定在開啟位置。

修剪說明

 注意腳下與身體的平衡，請勿過度伸張雙手。

修剪樹籬時，請佩帶護目鏡及穿防滑鞋。使用雙

手握緊裝置，然後將其啟動。如本使用手冊中的

插圖所示，務必按照以下方式握持修剪機：一隻

手握住開關手柄，另一隻手握住弓形輔助手柄

(圖 H)。切勿握住刀片防護罩。

修剪剛長出的樹籬（圖 I）

 最有效的操作方式是進行大範圍的橫掃動作，

用刀齒切割樹枝。沿刀片運作的方向略微向下傾

斜刀片，可提供最佳的切割效果。

警告！不要修剪長過直徑 18 公釐的莖。請僅使用本修

剪機修剪房屋和建築物周圍的一般灌木。

平均修剪樹籬頂部（圖 J）

 若要平均地修剪樹籬頂部，可以在想要的高度綁

一條細繩作為參考線。

修剪樹籬側邊（圖 K）

 如圖所示般握持修剪機，於樹籬側邊由下往上

修剪。

卡枝排除按鈕

如出現堵塞的情況，請按下卡枝排除按鈕 (4)，如圖 l

所示。刀片將更緩慢和有力地來回移動，以修剪較難

切割的樹枝。鬆開按鈕以繼續正常地修剪樹籬。

註：鬆開按鈕後，刀片將立即全速轉動。

註：按住按鈕 15 秒後，刀片就會馬上停止轉動。若要

重新啟動卡枝排除功能，請鬆開按鈕並再次按下。

在進行正常修剪時，請勿持續按住卡枝排除按鈕。

繁體中文

維護

您的 BLACK+DECKER 插電/充電器具/工具採用卓

越的設計，能夠長時間使用，並且只需最少的維護。

若要持續獲得滿意的操作效果，需進行正確的工具維

護和定期的清潔。

警告！在插電式/充電式電動工具上執行任何維護工

作之前：

 請關閉電源並拔下裝置/工具的插頭。

 或者，若裝置/工具使用獨立電池組，請關閉電源

並將電池從裝置/工具卸下。

 又或者，若電池屬於內建電池，請使電池完全放

電，然後再關閉電源。

 清潔之前請拔下充電器的插頭。您的充電器除了

定期清潔之外，並不需要執行任何維護操作。

 定期使用軟刷或乾布清潔器具/工具/充電器內的

通風槽。

 定期使用濕布清潔電動機外殼。請勿使用任何研

磨性或溶劑型清潔劑。

 使用後，請仔細地清潔刀片。完成清潔後，在刀片

塗上一層薄薄的機油，以防止刀片生鏽。

切割刀片由優質的硬化鋼製成，正常使用時不需要重

新磨利。但是，如果您不小心碰到鐵絲網、石塊、玻

璃或其他硬物，您可能會在刀片上造成缺口。只要缺

口不干擾刀片的運作，便無需把它移除。如果缺口干

擾刀片的運作，請取出電池並使用精細的帶齒銼刀或

磨刀石去除缺口。如果您不小心摔落修剪機，請仔細

檢查是否有損壞。如果刀片彎曲、外罩破裂或手柄損

壞，或者如果您發現可能影響修剪機操作的任何其他

情況，請將修剪機送到您當地的 BLACK + DECKER

維修中心，待維修完成後方可重新使用。肥料和其他

園藝用化學品含有能加速金屬腐蝕的化學劑。請勿將

裝置存放在肥料或化學品之上或附近。取出電池後，

請僅使用中性肥皂與濕布來清潔裝置。切勿讓任何

液體進入工具；切勿將工具的任何部分浸入液體中。

完成清潔後，在刀片塗上一層薄薄的機油，以防止刀

片生鏽。

疑難排解

問題可能的原因可能的解決方案

刀片運行緩慢、

發出噪音或溫度

很高。

刀片乾燥和銹蝕。潤滑刀片。

刀片或刀片支承彎曲。拉直刀片或刀片支承。

刀齒彎曲或損壞。拉直刀齒。

刀片螺絲鬆脫。擰緊刀片螺絲。

裝置不會啟動。電池的安裝不正確。檢查電池的安裝。

電池未充電。檢查電池充電要求。

安全按鈕功能未完全正確操作。確保已完全按壓安全按鈕，然後才移動主觸發開關。

電池無法充電未將電池放入充電器。

將電池放入充電器，直到綠色

LED 燈持續亮起。

充電器未插電。

將充電器插入工作插座。若需更多詳細資訊，請參閱

「重要充電說明」。在插座中插入燈具或其他電器的插

頭，以檢查插座中是否有電流。檢查插座是否與燈具

開關相連接，如果連接，燈具開關在關閉燈具時會切

斷電源。

環境空氣溫度太高或太低。

將充電器和工具移至環境空氣溫度高於華氏

40 度

(4.5°C) 或低於華氏 105 度 (+40.5°C) 的環境中。

繁體中文

保護環境

分類收集。帶有此標誌的產品和電池必須

與一般家庭廢物分開處置。

產品和電池包含可重複使用或回收的材料，可降低

對原材料的需求。請根據當地法規回收電氣產品和

電池。

維修資訊

BLACK+DECKER

提供遍佈亞洲的公司隸屬及授權服

務地點。所有的 BLACK+DECKER 服務中心都具有訓

練有素的人員，為客戶提供高效、可靠的產品服務。

不論您需要的是技術建議、維修服務還是原廠正品

替換零件，都可以聯絡距您最近的

BLACK+DECKER

服務地點。

附註

 BLACK+DECKER 的政策是持續改善我們的產

品，因此，我們保留隨時變更產品規格的權利，

恕不另行通知。

 標準裝置和配件可能會根據不同的國家/地區而

有所不同。

 產品規格可能會根據不同的國家/地區而有所

不同。

 並非所有的國家/地區都將提供完整的產品系列。

如需各產品系列的供應情況，請聯絡您當地的

BLACK+DECKER 代理商。

經銷商：特力股份有限公司

地址：台北市內湖區新湖三路

23 號 1.2.5 樓

電話：0800-008-007

進口/

委製廠商：新加坡商百得電動工具（股）公司台灣分公司

地址：台北市士林區德行西路 33 號 2 樓

電話：02-2834-1741

N552001 12/2018

Black & Decker GTC18504PC User manual

Brand: Black & Decker

Model: GTC18504PC

Category: Cordless hedge trimmers

Type: User manual

Download PDF

report

Black & Decker GTC18504PC User manual

Black & Decker GTC18504PC User manual

Related papers

Other documents