Allnet ALL02860ND User guide

Network Management Software

ALLNET Zone Controller

For ALL0558N / ALL02850N / ALL02860ND / ALL02880ND

User Manual v1.0

2

Table of Contents

1. Installation & Un-installation ........................................................................ 4

1.1. Install NMS Suite .......................................................................................................... 4

1.1.1. Step 1: Introduction ............................................................................................ 4

1.1.2. Step 2: Choose Install Folder ............................................................................. 5

1.1.3. Step 3: Choose Shortcut Folder ........................................................................ 5

1.1.4. Step 4: Pre-Installation Summary...................................................................... 6

1.1.5. Step 5: Installing .................................................................................................. 6

1.1.6. Step 6: Install Complete ..................................................................................... 7

1.2. Uninstall NMS Suite ..................................................................................................... 8

1.2.1. Step 1: Introduction ............................................................................................ 8

1.2.2. Step 2: Uninstalling ............................................................................................. 9

1.2.3. Step 3: Uninstall Complete ................................................................................ 9

2. Software Layout ............................................................................................ 10

3. Feature List ..................................................................................................... 13

3.1. User Access ................................................................................................................. 13

3.2. Log Out ....................................................................................................................... 15

3.3. User Access ................................................................................................................. 16

3.3.1. Create User ........................................................................................................ 16

3.3.2. Edit User ............................................................................................................. 18

3.3.3. Delete User ........................................................................................................ 19

3.4. Network Discovery .................................................................................................... 20

3.5. Map .............................................................................................................................. 23

3.5.1. Background Image ............................................................................................ 23

3.5.2. Transparency ..................................................................................................... 24

3.5.3. Map Zoom ......................................................................................................... 25

3.5.4. Map Scale ........................................................................................................... 26

3.5.5. Create New Map ............................................................................................... 28

3

3.5.6. Node Labels ....................................................................................................... 30

3.5.7. Node Details ...................................................................................................... 33

3.5.8. Node Coverage ................................................................................................. 34

3.6. Nodes Properties ....................................................................................................... 37

3.7. Block Node ................................................................................................................. 40

3.8. Import/Export Profile ................................................................................................ 41

3.9. STATS Tab ................................................................................................................... 42

3.10. DEVICE Tab ................................................................................................................. 44

3.11. USER Tab ..................................................................................................................... 45

3.12. Block User ................................................................................................................... 46

3.13. Unblock User .............................................................................................................. 47

3.14. Node Reboot .............................................................................................................. 48

3.15. Node Upgrade ........................................................................................................... 49

3.16. Quick Config ............................................................................................................... 50

3.17. Configure Node ......................................................................................................... 52

3.17.1. General Page ..................................................................................................... 52

3.17.2. Wireless Page .................................................................................................... 53

3.17.3. Wireless > Security Page .................................................................................. 54

4

1. Installation & Un-installation

1.1. Install NMS Suite

Obtain the installation file all_install_1_0_3(withVM).exe from the

companion CD or FTP, and execute it at the system you would like to

install. Wait for the installer to loaded completely and follow the 6 steps

of the installation wizard.

1.1.1. Step 1: Introduction

The introduction step describe briefly about the installation. Click the

Next button to proceed to the next step.

5

1.1.2. Step 2: Choose Install Folder

Select the destination for the installation. By default the wizard select the

Program Files directory for windows user. User can change the directory

by entering the path at the provided field or use the Choose button to

select the desired location. Click the Restore Default Folder button if you

wish to change the install folder back to the default folder.

Click the Next button to proceed to the next step.

1.1.3. Step 3: Choose Shortcut Folder

Choose where to create the shortcut file for the NMS suite launcher. If you

do not need the shortcut file, select the Don’t create icons option at the

bottom.

Click the Next button to proceed to the next step.

6

1.1.4. Step 4: Pre-Installation Summary

Check the summary of the installation information and if everything is

fine, click the Install button to start the installation process.

1.1.5. Step 5: Installing

The installation is in progress and it might takes about 30 seconds. It

would proceed to the final screen automatically upon completed.

7

1.1.6. Step 6: Install Complete

Installation is completed. The ALLNET NMS Suite is now successfully

installed in your system. Click the Done button to close the installation

wizard. You may now launch your NMS suite from the shortcut you

created just now.

8

1.2. Uninstall NMS Suite

In order to uninstall the NMS suite from your system, click the uninstaller

file from the short cut. Alternatively, the uninstaller can be found at the

_ALLNET Zone Controller 1.0.3_installation folder located at the NMS

install path. Run the uninstaller entitled _ALLNET Zone Controller

1.0.3_installation Wait for the uninstaller to loaded completely, and follow

the next 3 simple steps to complete this process.

1.2.1. Step 1: Introduction

A brief description about the process. Click the Uninstall button to start

the uninstallation.

9

1.2.2. Step 2: Uninstalling

The uninstallation in progress. This could take about 30 seconds.

1.2.3. Step 3: Uninstall Complete

The uninstall process is completed. The NMS Suite is now removed

successfully from your system. Please note that the files created after

installation such as profiles and data files, will not be removed by the

uninstall process.

10

2. Software Layout

As overall, the NMS Suite software is divided to four different panels. User can switch

to each panel by selecting the tab button at the top of the suite. The four panels are

Map, Stats, Device and User.

The MAP panel is to display the live status of the managed network graphically. The

discovered unit will be plotted on the map area at the left panel. All new located

devices will be added to the Unplaced APs columns before dragged to the map by

the user.

The STATS tab is to monitor the statistic of the node unit that managed by the

software. User can view the record of the upload or download data bytes of the node

by utilizing the available options.

11

The DEVICE list, meanwhile, listed the discovered node units with their current data.

User can reboot or upgrade firmware of the selected unit at this panel.

The USER list tabulates the information of the clients that currently connected to the

node units which are monitored by the NMS.

12

13

3. Feature List

3.1. User Access

After installation, user can start the NMS suite via the launcher or shortcut

created during installation process. User is required to enter the correct

username/password in order to use access to the NMS. A window would popup

to prompt user for the login details, and by default, the username and password

are “admin” and “admin”.

User is strongly advised to change the default password upon first-time log in to

prevent unauthorized user to access to the system. To change the default admin

password, click the SETTINGS button at the top right corner to initiate the

editor.

14

Select the Admin tab, and click the Change button of the Password field.

Another popup dialog would appear to prompt user for the new password. Enter

the current password and the new password you would like to change and hit

the OK button upon completed.

15

3.2. Log Out

To log out from the system, click the Logout link at the top corner of the NMS

suite.

16

3.3. User Access

The admin can create user to co-manage the NMS suite. The only difference

between the admin and normal level user is the ability to manage user. The

admin has the privilege to create, change and delete a user. The user list is

located at the admin setting panel and this table can only be viewed by the

admin. To view the table, click the SETTINGS button at the top right corner to

launch the popup window, and you can find the table at the Admin tab.

3.3.1. Create User

In order to create a new user, click the Add button at the top of the User

List, a dialog box would popup to prompt user for the relevant information.

Enter the new username and provide a password.

17

At the Status field, option “Active” and “Inactive” are available. Select

“Active” would activate the user account and the user can log in

immediately. By choosing “Inactive” on the other hand, the user account will

be created but the user is not able to log in, until the admin switch the

status to “Active”.

Click OK button upon completing the process and the new user will be

generated.

18

3.3.2. Edit User

To edit a user account, select the desired user from the user list, and click

the Edit button. A popup dialog would appear to prompt user for the

following action.

Admin can change the status of the selected user by selecting the

appropriate option from the drop down list. If admin wish to update the

password for the user, enable the password fields by checking the Change

Password checkbox. Then, enter the new password at the Password and

Confirm fields and click the Edit button. The change would take place

instantly.

19

3.3.3. Delete User

In order to delete a user, select the desired user from the User List, and then

hit the Delete button. Confirm your action before proceed because the

change are not reversible.

20

3.4. Network Discovery

The main purpose of the NMS Suite is to monitor and manage the network.

Therefore it is vital for the system to be able to provide updated data recursively.

By the ALLNET NMS Suite, the system discovers the node unit by broadcasting

the SNMP packet. Active device around the network would respond to the NMS

to report their availability so that the NMS can locate them. Hence in other

words, to be able to be monitored by the NMS, these node units must have

SNMP running all the time.

In order to initiate a discovery loop, click the Start button at the top of the map.

The scanning process would begin to search for the active node unit. The

responding unit will be added to the UNPLACED APs area initially. User can then

drag and drop these unplaced units to the map with the appropriate

background map loaded. The discovery process would run recursively by the

interval set at the top right corner of the map. User can select the desired refresh

interval by selecting from the drop down list.

If you wish to stop the discovery process, click the Stop button at the top of the

map and the discovery loop will be stopped.

Page is loading ...

Allnet ALL02860ND User guide

This manual is also suitable for

Allnet ALL02860ND User guide

Related papers

Other documents