Page is loading ...
User Manual
User Manual - RevEAL Profile Junior – Prism Projection, Inc.
Product Specifications and Warnings
Please read this manual prior to use.
• This product is intended for professional use only.
• This product is designed for damp conditions, but is not suitable for wet locations.
• Due to risk of injury the safety cable MUST be attached while the product is suspended.
• The product requires the appropriate power supply. (90-264 VAC, 47-63 Hz)
• It is not intended for use on dimming circuits.
• Contact Prism Projection Service and Support prior to any service work or the product warranty may be
voided.
Basic Installation
Before installing this product please make sure that you have read all warnings and safety information provided in this
manual.
The product must be installed in a suitable manner to support the product weight and with the safety cable attached in such
a way that it cannot be removed without releasing the clip. The safety cable should be attached at all times during both
installation and removal of the product.
Safe Mounting
Always install the safety cable provided when mounting the product overhead. To install, loop the safety cable through the
yoke and the support structure and clip the carabineer to the safety cable. Make sure that the loop cannot slip off the support
structure.
Attaching Data and Power Cables
Note: This lighting fixture can be used individually or modules can be daisy chained. In a chain of fixtures each
module can be individually addressed, or each can have its own address wherein each fixture is independent of
the others.
Step 1: If needed attach an appropriate connector to the end of the power cord included with the product. Any connector
you attach to the end of the product must be rated for 15 Amperes and 250VAC, and of the grounding type. The conductors
in the power cable are color coded for ease of assembly.
Wire Color Conductor Function
Green or Green with Yellow Stripe GROUND
Blue or White NEUTRAL
Brown or Black LINE
User Manual - RevEAL Profile Junior – Prism Projection, Inc.
Step 2: After attaching the appropriate connector to the power cord you can attach the power cord to the fixture. The power
cord will go into the power-in port. Slide the connector into the port and twist the connector clockwise.
Step 3: Now that the unit has power you need to provide data to the unit. This is done by plugging in an approved 5 pin
DMX cable. The data-in port is found on the rear of the fixture. If you have daisy chained your units, data-in from your
second unit should come from the data-out port of the first unit. Continue attaching cables in this fashion, 1 to 2, 2 to 3, and
so on. Follow best practices for DMX wiring. Do not exceed recommended cable lengths or number of receivers on a chain.
Care and Maintenance
It is recommended that care always be exercised when handling the fixture. It contains electronic components and is
susceptible to damage if dropped or exposed to excessive heat (above 105° F/40° C) or water. The fixture is not
recommended for outdoor locations unless in an approved outdoor protective enclosure. Periodically check and clean the air
filter at the base of the fixture. To clean the front lens on the fixture body, wipe down with a clean soft cloth. Periodically
check the fixture yoke hex bolts to make sure they are securely fastened. The air vents located around the top portion of the
fixture body should be clear of obstructions.
.
Product Overview
User Manual - RevEAL Profile Junior – Prism Projection, Inc.
AccessorySlot
LensBarrelLockScrew
Lens Barrel
YokePosition
AdjustmentScrew(2)
MountingHole
Yoke Handle Lock Knob
User Interface
All connections, settings and control options are located on the rear of the fixture, as illustrated below. The Navigation
Buttons can be used to access control settings and display fixture status on the Navigation Screen.
User Manual - RevEAL Profile Junior – Prism Projection, Inc.
PowerIn
/
Out EthernetPort
DMXIn
/
Out
IntensityControlKnob
Navi
g
ationScreen
Navi
g
ationButtons
FirmwareU
p
date Port
PowerOnOff
Switch(Connector)
User Manual - RevEAL Profile Junior – Prism Projection, Inc.
Home Screen
The Home Screen displays the current fixture status including color
temperature, intensity, DMX address, and number of DMX channels in use. The
rotating fan symbol at the top right indicates the fan is working properly.
Menu Screen
The Menu Screen offers four options for control. Select Fixture Address,
Channel Personality, Standalone Control, or TrueSource to advance to the
desired control feature set.
Fixture Address Screen
Use this screen to select either DMX address (1-512) or Art-Net universe (0-0
to 15-15) and to choose either 8 or 16 bit encoding. The screen displays the
fixture IP and MAC address at the bottom.
Channel Personality Screen
Use this screen to select color personality (CCT or Full White), Intensity
(Standard or Linear), Advanced Settings (Eco or Full Power, Algorithm,
Refresh Rate) or Factory Reset. Eco Mode under Advanced Settings puts the
fixture in a low power fan-less state. Light output is reduced by approximately
40%. Set Refresh Rate to Medium for most applications. High is intended for
high frame rate uses. Fixture options will vary depending on model number.
Standalone Control Screen
For operation without DMX or Art-Net in a standalone setting. Use this screen
to adjust the intensity and in some fixture models the CCT value. Powering off
the fixture from this screen will save the last fixture settings including intensity
and color.
TrueSource Screen
This screen displays the CIE value of the color of the light being produced by
the fixture. The screen shows both the target and actual color value in X,Y
coordinate values to assure TrueSource active color calibration is active and
monitoring performance.
Modes and DMX Channels
Operating modes are set by using the button pad to navigate to the Personality and Fixture Address Menus. The menu allows the user to adjust; Color Mode, Color
Temperature, Intensity (dimmer curve) and select Advanced Features such as power control. Remote power setting permits the user to control ECO and FULL power setting
via DMX.
NOTE: If the advanced feature power mode is set to REMOTE the first DMX channel on the instrument will be assigned to it and all the channels listed below will be shifted
up by one channel.
ColorModes
RevEAL Profile Junior offers a calibrated color mode and the option to only use white (CCT). Use the up and down buttons to select “Color” then use the left and right buttons
to choose between no color and XY mode.
While RevEAL instruments contain 5 base colors of LEDs, they are controlled within calibrated color systems. This ensures that the TrueSource optical sensor is
actively monitoring and calibrates color.
Color Mode - CIE x,y
CIE x,y allows the user to select color from the CIE 1931 2° Observer color space.
To determine the DMX decimal values for a given coordinate, simply multiply the coordinate by 255. For example 3200K white light has an x value of 0.4254 and a y of
0.4044.
x value: 0.4254 x 255 = 108 (42%)
y value: 0.4044 x 255 = 103 (40%)
In 16 bit mode, the multiplier is 65535;
x value: 0.4254 x 65535 = 27878 (42%)
y value: 0.4044 x 65535 = 26502 (40%)
If the Color Temperature channel is enabled, the color temperature channel will “take over” color control from the color channels. Generating white light in the Kelvin value
specified by the Color Temperature channel.
CIE x,y DMX Map (8 bit control):
1st Color Channel 2nd Color Channel
x coordinate y coordinate
CIE x,y DMX Map (16 bit control):
10
1st Color Channel 2nd Color Channel 3rd Color Channel 4th Color Channel
x course x fine y course y fine
White(CCT)
Available Options: Enabled, Disabled, Correction
When enabled the White setting creates a Correlated Color Temperature (CCT)Channel. If the CCT channel is at any value other than 0, white colors will be produced by the
instrument. At full the color generated will be 8000K white, at 11% the color generated will be ~3200K white. As the channel value is raised the color temperature will go up.
If CCT is at any value other than 0 and the Color Mode is any setting other than None, the instrument will ignore the color channels and only create white light. Moving the
CCT channel to 0 will bump the instrument to wherever the color channels are set.
If the Correction option is selected, a channel will be added following the CCT channel that allows for the adjustment of green and magenta in the CCT output. The
Correction channel should be defaulted to 50% (127) for no correction. Raising the Correction channel will add up to 5 units of green. While lowering the Correction
channel will add up to 5 units of magenta. This feature is important of the user is attempting to balance to sources that may have color shift towards green or magenta, such has
fluorescents or only white LED devices.
If using the Correction option, ensure that Color is selected for the Algorithm found in Advanced Settings.
If enabled, in 8 bit mode 1 channel will be added after the color channels, 2 channels will be added if 16 bit control is being used.
If Correction is selected, in 8 bit mode 2 channels will be added after the color channels, 4 channels will be added if 16 bit control is being used. CCT channel(s) then
Correction channel(s).
Intensity
Available Options: Linear, Standard
Users may select either from a linear dimming curve or square law dimming. Square law dimming is frequently used in television production with the low end and top end of
the dimming curve are smoothed out.
RevEAL instruments always use an intensity channel, in 16 bit operation 2 channels are used.
11
RevEAL Profile Junior
DMX Chart
Variable White
Menu Settings:
Channel Personality> White (Full White, Variable White)
Channel Personality> Intensity (Linear, Standard)
Channel Personality> Advanced Settings > Energy (Full, Eco)
Channel Personality> Advanced Settings > Refresh Rate
Advanced Settings > Algorithm
Advanced Settings > Algorithm
8 Bit Chan Control
Item Default
Range Function
1 n CCT 0 0, 255 2800K-5600K
2 n+1 Intensity 0 0, 255 0% - 100%
16 Bit Chan Control
Item Default
Range Function
1 n CCT 0 0, 255 2800K-5600K Course Adj.
2 n+1 CCT 0 0, 255 2800K-5600K Fine Adj.
3 n+2 Intensity 0 0, 255 0% - 100%
7
RevEAL Profile Junior
DMX Chart
Fixed White
Menu Settings:
Channel Personality> White (Full White)
Channel Personality> Intensity (Linear, Standard)
Channel Personality> Advanced Settings > Energy (Full, Eco)
Channel Personality> Advanced Settings > Refresh Rate
Advanced Settings > Algorithm
8 Bit Chan Control
Item Default
Range Function
1 n Intensity 0 0, 255 0% - 100%
RevEAL Profile Junior
DMX Chart
Variable White + Correction
Menu Settings:
Channel Personality> White (Variable CCT, CCT + Correction)
Channel Personality> Intensity (Linear, Standard)
Channel Personality> Advanced Settings > Energy (Full, Eco)
Channel Personality> Advanced Settings > Refresh Rate
Advanced Settings > Algorithm
8 Bit Chan Control
Item Default
Range Function
1 n CCT 0 0, 255 2800K-5600K
2 n+1 Correction 127 0, 255
+10 Magenta, +10 Green,
127 – No Correction
3 n+2 Intensity 0 0, 255 0% - 100%
16 Bit Chan Control
Item Default
Range Function
1 n CCT 0 0, 255 2800K-5600K Course Adj.
2 n+1 CCT 0 0, 255 2800K-5600K Fine Adj.
3 n+2 Correction 127 0, 255
+10 Magenta, +10 Green,
Course Adj.
4 n+3 Correction 127 0, 255
+10 Magenta, +10 Green,
Fine Adj.
5 n+4 Intensity 0 0, 255 0% - 100%
8
9
RevEAL Profile Junior
DMX Chart
Color + Variable White + Correction
Menu Settings:
Channel Personality> Color (X,Y)
Channel Personality> White (Variable CCT, CCT + Correction)
Channel Personality> Intensity (Linear, Standard)
Channel Personality> Advanced Settings > Energy (Full, Eco)
Channel Personality> Advanced Settings > Refresh Rate
Advanced Settings > Algorithm
8 Bit Chan Control
Item Default
Range Function
1 n X 0 0, 255 X coordinate color value
2 n+1 Y 0 0, 255 Y coordinate color value
3 n+2 CCT 0 0, 255 2800K-5600K
4 n+3 Correction 127 0, 255
+10 Magenta, +10 Green,
127 – No Correction
5 n+4 Intensity 0 0, 255 0% - 100%
16 Bit Chan Control
Item Default
Range Function
1 n X 0 0, 255 X color value, coarse adj.
2 n+1 X 0 0, 255 X color value, fine adj.
3 n+2 Y 0 0, 255 Y color value, coarse adj.
4 n+3 Y 0 0, 255 Y color value, fine adj.
5 n+4 CCT 0 0, 255 2800K-5600K Course Adj.
6 n+5 CCT 0 0, 255 2800K-5600K Fine Adj.
7 n+6 Correction 127 0, 255
+10 Magenta, +10 Green,
Course Adj.
4 n+7 Correction 127 0, 255
+10 Magenta, +10 Green,
Fine Adj.
8 n+8 Intensity 0 0, 255 0% - 100%
12
PrismProjection,Inc.
8228East124thStreetSouth
Sully,IA50251
+1(641)594‐3356
Toreceiveanelectroniccopyofthisusermanual,
pleasescantheQRcodebelow.
/
