Medion Medion Dual 10 Amp Charger Owner's manual

Page is loading ...

0668

[

m e d i o n

]

dual 10 amp

[ 1 ]

1. Exterior of the unit

2. Speciﬁcations & Features

3. Cell type charge parameters

4. Warnings and safety notes

5. Connecting the charger

6. Balance socket

7. Using the audio speakers

8. Program ﬂow chart

9. Initial Parameter set up (Users’ set up)

10. Lithium battery (LilO/LiPO/LiFe) program

10.1 Charging Lithium batteries

10.2 Charging Lithium batteries in balance mode

10.3 “FAST” Charging Lithium batteries

10.4 “STORAGE” Control Lithium batteries

10.5 Discharging Lithium batteries

10.6 Voltage balancing and monitoring during discharge

11. NiMH/NiCD battery program

11.1 Charging NiCD/NiMH batteries

11.2 Discharging NiCD/NiMH batteries

11.3 Charge-to-discharge & discharge-to-charge cycle NiMH/NiCD batteries

12. Pb (lead-sulphuric acid) battery program

12.1 Charging Pb batteries

12.2 Discharging Pb batteries

13. IR-mode™ Internal Resistance Test Program

14. Save Data Program

15. Load Data Program

16. Miscellaneous information screens

17. Warning and error messages

18. Glossary of terms

19. Maximum circuit power charts

20. Warranty and service

21. French Translations

22. Spanish Translations

23. German Translations

24. Japanese Translations

2

2-3

4

5

6

7

8

9

10-11

12-15

12

13

14

15

16-17

16

17

17-18

17

18

19

20

21

22-23

24

25

26

27-52

53-78

79-104

105-130

CONTENTS

0668

[

m e d i o n

]

dual 10 amp

[ 2 ]

SPECIFICATIONS

SPECIFICATIONS:

Input Voltage: 11.0-18.0V

Circuit Power: 200W max charge x 2, 25W max discharge x 2

Charge Current: 0.1-10.0A x 2

Discharge Current: 0.1-5.0A x 2

Current Drain for LiPO Balance: 200mAh/cell

NiCD/NiMH Cell Count: 1-18 Series

Lithium Cell Count: 1-6 Series

Pb Voltage: 2-20V

Alarm Voltage: Lower than 10V or greater than 18V

Weight: 3lbs 10oz (1650g)

Dimensions: 11.8x5.9x3.35 in (300x150x85mm)

Input power cable

(DC 11V - 18V)

CH1/CH2

(To select Output)

LCD screen

(16chr. x 2 lines)

Batt type / Stop

To select main program

To stop the operation

Dec / Inc

To select sub program

To alter the value

Start / Enter

To resume or

start the operation

Charging lead connector

(4 mm banana female)

Temperature Sensor Port

Balance Port

USB Output

(DC 5V/1A)

Audio Input

0668

[

m e d i o n

]

dual 10 amp

[ 3 ]

[Operating Software]

The microprocessor controlled CPU has software with multiple levels of battery monitoring for

maximum safety. Error warnings include: input voltage warning, reverse polarity protection and

Lithium cell count input error warning.

[High Power Charge Circuit]

Dual 200-watt charge circuits can charge up to 18 NiCD/NiMH or 6 Lithium cells with a maximum

current of 10A. A temperature controlled internal cooling system keeps the whole operating

system working at maximum efﬁciency in a wide variety of conditions.

[Dual Audio Speakers]

The Medion Dual 10 Amp Charger has two integrated speakers with a standard audio input

allowing the user to play music from their MP3 player, or smart phone right in their pit area or

workshop.

[USB Power Output]

5V 1A USB power outlets for charging smart phones, MP3 player, or included LED light.

[Cell Balancer for Lithium Batteries]

A built-in monitoring circuit can check and regulate the voltage of individual cells in a Lithium

battery pack. It can monitor and balance packs in charge, discharge, and storage modes.

[Supports Multiple Lithium Chemistries]

Accepts three types of Lithium battery chemistries, including LiPO, LiIo, and LiFe.

[Lithium Storage and Fast Charge Modes]

Storage mode conditions Lithium batteries for long-term storage. Fast charge mode safely charges

Lithium batteries at high rates without risk of damage to the pack.

[Temperature Limit]

Using the included external temperature probe, a thermal shut down temperature can be set. This

will stop the charge or discharge process should a battery exceed the temperature limit to prevent

overcharging, ﬁre, or other damage.

[Safety Timer]

This will stop the charge or discharge process if the charger cannot detect a peak, or if the

capacity limit is not tripped.

[Input Power Monitor]

Charging or discharging processes will stop if the input voltage is too low. This is to protect the

input source, usually a 12V car battery.

[Data Store/Load]

For ease-of-charging or discharging on frequently used packs, 5 different programmable battery

proﬁles are available.

FEATURES

0668

[

m e d i o n

]

dual 10 amp

[ 4 ]

The chart below has all the basic charge parameters for different cell types. Actual

charge and discharge rates or voltages may vary by manufacturer or recommended cell

performance. Always consult with the manufacturer instructions for your speciﬁc battery

for proper charge parameters.

NiCD / NiMH

Lilo

LiPO

LiFe

Pb

Voltage Level: 1.2V/cell

Allowable fast charge current: 1C~2C

(Depends on the performance of the cell)

Discharge voltage cut-off level: 0.85V/cell (NiCD), 1.0V/cell (NiMH)

Voltage Level: 3.6V/cell

Max charge voltage: 4.1V/cell

Allowable fast charge current: 1C or less

Minimum discharge voltage cut-off level: 2.5V/cell or higher

Voltage Level: 3.7V/cell

Max charge voltage: 4.2V/cell

Allowable fast charge current: 1C or less

Discharge voltage cut-off level: 3.0V/cell or higher

Voltage Level: 3.3V/cell

Max charge voltage: 3.7V/cell

Allowable fast charge current: 4C or less (e.g. A123M1)

Discharge voltage cut-off level: 2.0V/cell or higher

Voltage Level: 2.0V/cell (Lead-acid)

Max charge voltage: 2.46V/cell

Allowable fast charge current: 0.4C or less

Discharge voltage cut-off level: 1.50V/cell or higher

CELL TYPE CHARGE PARAMETERS

0668

[

m e d i o n

]

dual 10 amp

[ 5 ]

WARNING

1. Always use a charger speciﬁcally designed for the chemistry of the battery to be charged.

Never use NiCD or NiMH type chargers to charge LiPO batteries. Never use a LiPO type

charger to charge NiCD or NiMH batteries. Failure to do so will damage the batteries and

may cause ﬁre and personal injury. When charging NiMH batteries, you must use a linear

charger with peak detection. Do not use a timer charger. Charge battery at no higher than a

1C charge rate. To calculate your battery’s 1C charge rate, divide the battery capacity (mAh)

by 1000.

Example: 3000mah ÷ 1000 = 3amps, 4200mah ÷ 1000 = 4.2amps, etc.

2. Always charge batteries in a ﬁre proof container. Do not charge batteries on or near wood,

cloth, carpet, in your model, or on or near any other ﬂammable material. Keep a chemical ﬁre

extinguisher near by in case of ﬁre.

3. Never leave batteries unattended while charging. Always observe batteries when charging

so that you may react quickly to any problems that may occur.

4. If a battery is deformed, swollen or appears damaged, DO NOT CHARGE. Follow the disposal

instructions below to properly and safely dispose the battery.

5.

Any time you have an accident with your model or if the battery swells “balloons” or if the

battery exceeds temperature guidelines, follow these safety steps:

a. Immediately remove the battery pack from your model or charger.

b. Place the battery in a non-ﬂammable, well ventilated area.

c. Observe the battery for 30 minutes from a safe distance.

d. After 30 minutes, if the pack appears stable, is not swollen and does not show any signs of

damage, return the battery pack to normal use with caution.

6. Do not let exposed battery wires touch each other. This may cause the battery to short and

potentially cause a ﬁre.

7. Store your batteries in a cool, dry place between 40-80 Fº / 4-26 Cº. Batteries must be stored

at 3.75-3.80 volts per cell to maintain capacity and pack life. Do not store fully charged for

longer than one week to prevent damage.

8. Do not assemble unmatched or dissimilar LiPO cells.

9. Store battery packs out of the reach of children and pets.

CHARGING WARNINGS

BATTERY DISPOSAL INSTRUCTIONS

1. Discharge battery pack to 2.5 Volts per cell or less.

2. Fill a bucket with enough water to submerge the battery pack completely.

3. Add salt to the water until no more salt will dissolve; the water is nowsaturated with salt.

4. Place the battery pack in the bucket and leave submerged in the salt water solution for 24 hours.

5. Remove the battery pack from the salt water and test the voltage.

6. If the voltage does not read 0.0 Volts, re-submerge and re-test untilthe voltage reads 0.0 Volts.

7. Once the battery pack has been discharged to 0.0 Volts, it is safe to dispose of in the trash.

0668

[

m e d i o n

]

dual 10 amp

[ 6 ]

The Venom™ Medion Dual 10 Amp Charger comes with male 4mm

bullet connectors attached to the power input cables. These cables are

appropriate for attaching directly to most high quality AC to DC power

supply units. Also included are large alligator clips with matching 4mm

female bullet connectors for attaching directly to 12V car batteries. It is

critically important that you use either a fully charged 13.8V car battery

or a high quality AC to DC power supply in the range of 11-18V.

Using Alligator

Clips attached

to car battery.

IMPORTANT

CONNECTING THE BATTERY

Before connecting a battery, it is absolutely essential to check one last time

that you have set the parameters correctly. If the settings are incorrect, the

battery may be damaged, and could even burst into ﬂames or explode. To avoid

short-circuits between the banana plugs, always connect the charge leads

to the charger ﬁrst, and only then to the battery. Reverse the sequence when

disconnecting the pack.

CONNECTING THE CHARGER

0668

[

m e d i o n

]

dual 10 amp

[ 7 ]

The balance wire attached to the battery must be connected to the charger’s

balancing port. Take care to maintain correct polarity!

(Wiring diagram: see below.)

This photo shows the correct way to connect your battery to the Medion Dual 10

Amp Charger while charging in the balance charge program mode only.

NOTE:

The balance socket is a diagnostic connection only. Battery discharge leads

must be connected to allow for a proper charge connection.

WARNING

Failure to connect as shown in this photo will damage this charger.

To avoid short circuit between the charge lead, always connect the charge

cable to the charger ﬁrst, then connect the battery. Reverse the sequence when

disconnecting.

Balance socket connection left

Balance socket connection right

BALANCE SOCKET

0668

[

m e d i o n

]

dual 10 amp

[ 8 ]

Your Venom™ Medion Dual 10 Amp Charger is equipped with twin speakers

to play music from your MP3, iDevice, or smart phone.

Plug the included audio cable into the Audio port on the left side of the

charger.

Connect the other end of the audio cable to your device.

Audio In

Start the music. Volume of the music is controlled through the internal

volume control in your music device.

USING THE AUDIO SPEAKERS

0668

[

m e d i o n

]

dual 10 amp

[ 9 ]

PROGRAM FLOW CHART

0668

[

m e d i o n

]

dual 10 amp

[ 10 ]

The Venom™ Medion Dual 10 Amp Charger has default settings in the User Set

menu that can be adjusted in this ﬁrst step. The screen displays the following

information in sequence and the user can change the value of the parameter

on each screen. When you want to alter the

parameter value in the program, press the Start/

Enter button once. The value will start ﬂashing. It

can be changed by using the INC or DEC buttons,

and ﬁnally saved by pressing the Start/Enter

button once.

The screen displays the nominal voltage of a

Lithium battery. There are three kinds of Lithium

batteries: LiFe (3.3V), LiIO (3.6V) or LiPO (3.7V). It

is very important to check the battery and set up

correctly for the chemistry type. If it is different

from the correct value, the battery may explode

during the charge process.

The Venom™ Medion Dual 10 Amp Charger

recognizes the cell count of Lithium batteries

automatically at the beginning of the charge or

discharge process to avoid erroneous settings

by the user. A deeply discharged battery can be

recognized incorrectly by the charger. To prevent

the error, you can set the time term to verify the

cell count by the processor. Normally, 10 minutes

is enough to perceive the cell count correctly.

For a battery of larger capacity, you may

extend the time term. If you set the time term too long for a battery of smaller

capacity, the charge or discharge process may ﬁnish within the time term

with the erroneous cell count. This may cause lethal results. If the processor

recognizes the cell count incorrectly at the beginning of the charge or

discharge process, you may extend the time. Otherwise use the default value.

Delta peak of NiCD and NiMH battery

This is the setting to set the sensitivity for the charger to detect the peak on a

NiCD or NiMH battery. The effective value ranges from 5 to 20 mV per cell. If the

trigger voltage is set higher, there is a danger of overcharging the battery. If it

is set lower, there is a possibility of premature termination. Please refer to the

technical speciﬁcation of the battery. (NiCD default: 12mV, NiMH default: 7mV).

USER SETUP PROGRAMMING MENU

0668

[

m e d i o n

]

dual 10 amp

[ 11 ]

An optional feature to protect the battery is the

external temperature probe. The temperature cut-

off can be On or Off. If it is On, set the maximum

temperature at which the charger should allow

battery to reach during charge. Once a battery

reaches this temperature during charge, the process

will be terminated to protect the battery.

When using the battery cycle feature of charging

and discharging, a battery will become warm after

the charge or discharge period. This program can

insert a time delay to occur after each charge and

discharge process to allow the battery adequate

time to cool down before being subjected to the next

process. The value ranges from 1-60 minutes.

Trickle charge mode for NiMH, NiCD, and PB

batteries. This can be set to On or Off. With this

mode turned On, the charger will automatically

supply a trickle current to the battery after fast

charging has ended. This trickle will be enough to

maintain full charge without overheating.

Note: Trickle charging a NiMH battery may damage the pack

When you start a charge process, the integral

safety timer automatically starts running at the same

time. This is to prevent overcharging the battery if

it proves faulty, or if the termination circuit cannot

detect that the battery is full. The value for the safety

timer should be generous enough to allow a full

charge of the battery.

This program sets the maximum charge capacity that will be supplied to the battery

during charge. If the delta peak voltage is not detected nor the safety timer expired

for some reason, this feature will automatically stop the process at the selected

capacity value.

The beep sounds every time a button is pressed to conﬁrm your action. The beep or

melody sounds at various times during operation to alert different mode changes.

These audible sounds can be On or Off.

USER SETUP PROGRAMMING MENU (CONTINUED)

0668

[

m e d i o n

]

dual 10 amp

[ 12 ]

This program monitors the input voltage of the

source. If the voltage drops below the value you

set, the operation forcibly terminates to protect

the input source.

The backlight intensity of the LCD screen can be

adjusted to suit different conditions.

These programs are only suitable for charging and discharging Lithium batteries

with a nominal voltage of 3.3V, 3.6V and 3.7V per cell. Lithium batteries use a

charge technique termed constant voltage (CV) and constant current (CC). The

charge current varies according to the battery capacity and performance. The

ﬁnal voltage of the charge process is also very important. It should be precisely

matched to the charge voltage of the battery. They are 4.2V for LiPO, 4.1V for LiIo,

and 3.7V for LiFe. The charge current and nominal voltage as for cell count set on

the charge program must always be correct for the battery to be charged.

To alter a parameter value in the program, press Start/Enter button to make it

ﬂash, then change the value with INC or DEC button. The value will be stored by

pressing Start/Enter button once.

CHARGING LITHIUM BATTERY

The left side of the ﬁrst line shows the type of

battery you select in the User Set menu. The

value on the left side of second line sets the

charge current and the value on the right side of

second line sets the voltage of the battery pack.

After setting the current and voltage press Start/Enter button for more than 3

seconds to start the process.

Charge current : 0.1-10A, Voltage: 1-6 Series

LITHIUM BATTERY PROGRAM

0668

[

m e d i o n

]

dual 10 amp

[ 13 ]

After pressing start, the charger will display the

number of cells you set up and the processor

detects. “R” shows the number of cells recognized

by the charger and “S” is the number of cells

selected by the user on the previous screen. If both

numbers are identical, you can start charging by

pressing Star/Enter button. If not, press the Batt

Type/Stop button to go back to previous screen.

Carefully check the number of cells of the battery

pack and then press Start/Enter to charge again.

The screen shows the real-time progress during charge process. To stop

charging, press Batt Type/Stop button once.

BALANCE CHARGING LITHIUM BATTERY

This feature will charge while equalizing all the individual cell voltages within

the pack. This differs from the regular charge mode, which only looks at the total

battery pack voltage. The battery pack to be charged should be connected to

the suitable balance port of the cell balance block. You also need to connect the

main battery output plug to the output of the charger.

The left side of the ﬁrst line shows the type of battery you select at the users

setting. The value on the left side of second line sets a charge current and the

value on the right side of second line sets the voltage of the battery pack.

After setting the current and voltage press Start/

Enter button for more than 3 seconds to start the

process.

Charge current: 0.1-10A, Voltage: 1-6 Series

After pressing start, the charger will display the

number of cells you set up and the processor

detects. “R” shows the number of cells

recognized by the charger and “S” is the number

of cells selected by the user on the previous

screen. If both numbers are identical you can

start charging by pressing Star/Enter button. If not, press the Batt Type/Stop

button to go back to previous screen. Carefully check the number of cells of the

battery pack and then press Start/Enter to charge again.

LITHIUM BATTERY PROGRAM (CONTINUED)

0668

[

m e d i o n

]

dual 10 amp

[ 14 ]

The screen shows the real-time progress during charge process. To stop

charging press Batt Type/Stop button once.

FAST CHARGING LITHIUM BATTERY

Lithium charge proﬁles are set so the feeding

current gradually reduces near the end of the

charge to maintain the constant voltage. (CV)

To ﬁnish the charging process faster, this program

shortens the amount of time for the CV process

and ends earlier. The charging current will go to 1/5 from the initial value to end

the process while the normal Lithium charge process reduces to 1/10 during the

CV term. The ﬁnal charged capacity will be slightly less than if using the regular

charge feature, and charge time is greatly reduced.

You can set up the charging current and the

voltage of the battery pack being charged. As you

press Start/Enter button, the voltage conﬁrmation

will be displayed. Then if you conﬁrm the voltage

and current, press Start/Enter button again to

start charging.

The screen shows the real-time progress during

fast charge process. To stop charging press Batt

Type/Stop button once.

STORAGE MODE FOR LITHIUM BATTERY

Lithium batteries, if they are to be stored for a long time, need to be conditioned

and have their voltage set to a prescribed level to maintain long life. If stored

fully charged for a long period of time, packs will increase in internal resistance,

and lose power, or capacity. Use the storage feature for batteries that will be

stored for more than 30 days.

This program will determine to charge or discharge the battery to the storage

voltage depending on the battery at its initial stage. They are different from the

type of Lithium battery. 3.75V for LiIo, 3.85V for LiPO, and 3.3V for LiFe per cell. If

the voltage of battery at the start is over the storage voltage, the program will

start to discharge.

LITHIUM BATTERY PROGRAM (CONTINUED)

0668

[

m e d i o n

]

dual 10 amp

[ 15 ]

You can set up the current and the voltage of the

battery pack to be charged. The current will be used

to charge or discharge the battery to reach the

storage voltage.

The screen shows the real-time progress during

storage process. To stop charging, press Batt Type/

Stop button once.

DISCHARGING LITHIUM BATTERIES

The value of discharge current on the left side of

screen may not exceed 1C for a maximum safety

and the ﬁnal voltage on the right should not be

under the voltage level that is recommended by the

battery manufacturer to avoid deep discharging.

To start the discharge, press Start/Enter button for

more than 3 seconds.

Discharge current: 0.1-5A

The screen shows the real-time progress during

discharge. To stop charging, press Batt Type/Stop

button once.

VOLTAGE BALANCING AND MONITORING DURING DISCHARGE

The processor monitors the voltage of individual cells during storage mode

and discharge of a lithium battery pack. With the balance block attached to the

balance plug of the battery, it will equalize the voltage of each cell during the

storage and discharge function.

If the voltage of any one or more cells varies abnormally during the procedure, it

terminates the process automatically with the error message “Battery Voltage Cell

Low Vol”. If this happens, the battery pack contains

the bad cell, or the bad connection of the cable

plug. You can easily know which one cell is bad by

pressing INC button at time of the error message.

The processor detected the voltage of one cell in

the Lithium pack is too low.

In this case, the 4th cell is bad. If there is a

connection break in the cable or plug the voltage

value may show zero.

LITHIUM BATTERY PROGRAM (CONTINUED)

0668

[

m e d i o n

]

dual 10 amp

[ 16 ]

NiMH/NiCD BATTERIES

These battery charge proﬁles for NiMH (Nickel Metal Hydride) or NiCD (Nickel

Cadmium) batteries are commonly used in R/C vehicle applications. To alter the

value on the display, press Start/Enter button to make it ﬂash then change the

value using INC or DEC button. The value will be stored by pressing the Start/

Enter button once.

To start the charge process, press Start/Enter button for more than 3 seconds.

CHARGING NiCD/NiMH BATTERY

For this program, only the charge current needs to

be set. In “Aut” mode, you need to set the upper

limit charge current to avoid too high of charge

current that may damage the battery. Some

batteries of low impedance and small capacity can

lead to the higher charge current by the processor

at the automatic charge mod. In “Man” mode, it

will charge the battery with the charge current set

by the user in the display screen. Each mode can

be switched by pressing the INC and DEC button

simultaneously when the current ﬁeld is blinking.

The screen shows the real-time progress during charge. To stop charging, press

Batt Type/Stop button once.

DISCHARGING NiCD/NiMH BATTERY

Set discharge current on the left and the ﬁnal

voltage on the right. The discharge current ranges

from 0.1-5A and the ﬁnal voltage ranges from 0.1-

25V. To start the process, press Start/Enter button

more than 3 seconds.

Typical discharge voltage for NiCD/NiMH batteries

is .85V per cell for NiCD, and 1.0V per cell for NiMH.

For 6 cell NiCD’s it is .85 x 6 = 5.1V ﬁnal voltage.

The screen shows the real-time progress during

discharge. You can alter the discharge current by pressing Start/Enter button

during the process. Once you change the current value with the INC or DEC

button, store it by pressing the Start/Enter button again. To stop discharging,

press Batt type/Stop button once.

NiMH / NiCD BATTERY PROGRAMS

0668

[

m e d i o n

]

dual 10 amp

[ 17 ]

CYCLING NiCD/NiMH BATTERIES

This program can be used to charge then discharge, or discharge and then charge

NiCD/NiMH batteries. Set the sequence on the left

and the number of cycles on the right. You can use

this function for balancing, refreshing or breaking in

a battery. To avoid excess heat build up in the battery

during each charge or discharge sequence, there is a

“waste time” that can be set in the User Set program

menu, which is a brief cool off period. Cycle sequences

can range from 1-5.

To stop the process, press Batt type/Stop button once.

You can alter the discharge or charge current by

pressing Start/Enter button once during the process,

using the INC or DEC to change the setting, and the

Start/Enter button to save the setting. An audible alarm

will sound indicating the end of the cycle sequence.

At the end of the process you can view the charged or discharged capacity of the

battery. Press the INC or DEC button and the screen will display the results of each

cycle.

CHARGING PB (LEAD ACID) BATTERY

This program is for charging Pb (lead acid)

batteries with a nominal voltage from 2-24V.

Pb batteries are totally different from NiCD

or NiMH batteries. They can only deliver

relatively low current compared to their

capacity, and similar restrictions apply to

charging. The optimal charge current will be

1/10 of the capacity. Pb batteries must not be

charged rapidly. Always follow the instructions

supplied by the battery manufacturer.

Change the parameters of charging by pressing the Start/Enter button to make it

ﬂash. Then change the value with the INC or DEC button. The value will be stored

by pressing Start/Enter button once.

NiMH / NiCD BATTERY PROGRAMS (CONTINUED)

PB (LEAD ACID) BATTERY PROGRAM

1.)

2.)

0668

[

m e d i o n

]

dual 10 amp

[ 18 ]

(screen 1 Previous page) Set up the charge current on the left and the nominal voltage

of the battery on the right. The charge current ranges from 0.1-10.0A. The voltage

should match the battery being charged. Start the charge process by pressing

Start/Enter button for more than 3 seconds.

(screen 2 Previous page) The screen shows the real-time progress during charge. To

stop charging, press Batt Type/Stop button once.

DISCHARGING PB (LEAD ACID) BATTERY

Set discharge current on the left and the ﬁnal

voltage on the right. The discharge current ranges

from 0.1-5.0A. To start the process, press Start/

Enter button for more than 3 seconds.

The screen shows the real-time progress during

discharge. You can alter the discharge current

by pressing Start/Enter button once during the

process, using the INC or DEC to change the

setting, and the Start/Enter button to save the

setting.

This function allows the user to check the internal

resistance of lithium batteries. This is helpful as it

allows the user to track the health of the battery

by checking for increased pack resistance as the

battery ages. Attach the cell balance block to the

balance plug on the battery and the main pack

leads to the charger for this test.

Interface of the Internal Resistance Testing.

Press Start/Enter button to start the test.

Displays individual cell Internal Resistance (IR)

Press INC button to view total battery pack IR.

Pressing INC again will return to the individual cell IR.

PB (LEAD ACID) BATTERY PROGRAM (CONTINUED)

BATTERY INTERNAL RESISTANCE TEST MENU

Tes

tLixx Internal

Resistance

MeasuringI R

WaitDlease

1:0260 50 044M

1:0390 42 044 M

Batter

y

PackIR

231m

0668

[

m e d i o n

]

dual 10 amp

[ 19 ]

SAVE DATA PROGRAM

The data storage feature allows the user to store and load battery proﬁles for

frequently used batteries instead of always reprogramming the charger. This

feature will store up to 5 different battery proﬁles. To set up the parameter

value in the program, press Start/Enter button to make it blink, then change the

value with the INC or DEC button.

The proﬁle value set in the proﬁle screen does not

affect the charge or discharge process. They only

represent the speciﬁcations of the battery. The

following screens will automatically be displayed

exactly matched to the battery type you set up.

The example shows a NiMH battery, 12 cells and

3000mAh capacity.

Set up the charge current for manual charge

mode, or current limit for automatic charge mode.

Each mode can be switched by pressing the INC

and DEC button simultaneously when the current

ﬁeld is ﬂashing.

Set up discharge current and ﬁnal voltage.

Setting the cycle type and the number of cycles.

Press the Start/Enter button for more than 3

seconds to save the proﬁle. The above process is

similar for LiPO and Pb Batteries.

PROGRAM SELECT

0668

[

m e d i o n

]

dual 10 amp

[ 20 ]

This program recalls the data proﬁle that was saved in the “Save Data” program.

To load the proﬁle, press Start/Enter button once

to make the proﬁle number ﬂash and select the

proﬁle number using the INC or DEC button, then

pressing the Start/Enter button for more than 3

seconds.

Program Select

Select the Battery proﬁle number to be loaded.

Loading the data.

LOAD DATA

Page is loading ...

Medion Medion Dual 10 Amp Charger Owner's manual

This manual is also suitable for

Medion Medion Dual 10 Amp Charger Owner's manual

in other languages

Related papers

Other documents