Woodstock SHOP FOX W1738 Owner's manual

Model W1737/W1738

***IMPORTANT UPDATE***

Applies to Models Mfd. Since 1/14

and Owner's Manual Revised 11/09

Phone #: (360) 734-3482 • Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC

We made the following changes to this machine since the manual was printed:

• Obtained CSA certification meeting CSA C22.2 #105-1953 and UL 987-7th standards.

• Changed contactors, overload relays, and fuses inside electrical cabinet.

• Changed machine wiring.

• Replaced oscillation diaphragm assembly (P/N 503) with an air cylinder (P/N 503V2).

Note: At the top of each page is a note that indicates which page it replaces or adds to in the original

manual. On the parts list, the new parts are designated with a “V2”.

Aside from the information contained in this update, all other content in the owner's manual MUST be

read and understood for your own safety. IMPORTANT: Keep this update with the owner's manual for

future reference. If you have any further questions, contact our Technical Support.

New W1738 440V Conversion Kit

READ THIS FIRST

NEW W1738 440V CONVERSION KIT PARTS

38V2 X1738038V2 440V CONVERSION KIT V2.03.11

3-1V2 X1738003-1V2 OL RELAY SCHN LR3D325 17-25A V2.03.11

11-1 X1738011-1 OL RELAY SCHN LR3D07 1.6-2.5A

2V2

3V3

12-1

38V2

3-1V2

12-1

39

11-1

4V2

#13934TS Printed in Taiwan

-2-

Model W1737/W1738 (Mfd. Since 1/14)

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

This symbol is used to alert the user to useful information about

proper operation of the equipment or a situation that may cause

damage to the machinery.

NOTICE

SAFETY

OWNER’S MANUAL.

Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY.

Untrained operators

have a higher risk of being hurt or killed. Only

allow trained/supervised people to use this

machine. When machine is not being used,

disconnect power, remove switch keys, or

lock-out machine to prevent unauthorized

use—especially around children. Make

workshop kid proof!

DANGEROUS ENVIRONMENTS.

Do not use

machinery in areas that are wet, cluttered,

or have poor lighting. Operating machinery

in these areas greatly increases the risk of

accidents and injury.

MENTAL ALERTNESS REQUIRED.

Full mental

alertness is required for safe operation of

machinery. Never operate under the influence

of drugs or alcohol, when tired, or when

distracted.

ELECTRICAL EQUIPMENT INJURY RISKS. You can

be shocked, burned, or killed by touching live

electrical components or improperly grounded

machinery. To reduce this risk, only allow an

electrician or qualified service personnel to

do electrical installation or repair work, and

always disconnect power before accessing or

exposing electrical equipment.

DISCONNECT POWER FIRST. Always disconnect

machine from power supply BEFORE making

adjustments, changing tooling, or servicing

machine. This eliminates the risk of injury

from unintended startup or contact with live

electrical components.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating

or observing machinery to reduce the risk of

eye injury or blindness from flying particles.

Everyday eyeglasses are not approved safety

glasses.

Standard Machinery Safety Instructions

For Your Own Safety,

Read Manual Before Operating Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This

manual uses a series of symbols and signal words intended to convey the level of importance of the

safety messages. The progression of symbols is described below. Remember that safety messages by

themselves do not eliminate danger and are not a substitute for proper accident prevention mea-

sures—this responsibility is ultimately up to the operator!

SAFETY

Standard Machinery Safety Instructions

Replaces Page 6

-3-

Model W1737/W1738 (Mfd. Since 1/14)

WEARING PROPER APPAREL. Do not wear

clothing, apparel, or jewelry that can become

entangled in moving parts. Always tie back

or cover long hair. Wear non-slip footwear to

avoid accidental slips, which could cause loss

of workpiece control.

HAZARDOUS

DUST. Dust created while using

machinery may cause cancer, birth defects,

or long-term respiratory damage. Be aware of

dust hazards associated with each workpiece

material, and always wear a NIOSH-approved

respirator to reduce your risk.

HEARING PROTECTION.

Always wear hearing

protection when operating or observing

loud machinery. Extended exposure to this

noise without hearing protection can cause

permanent hearing loss.

REMOVE ADJUSTING TOOLS.

Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys,

wrenches, or any other tools on machine.

Always verify removal before starting!

INTENDED USAGE.

Only use machine for its

intended purpose—never make modifications

without prior approval from Woodstock

International. Modifying machine or using

it differently than intended will void the

warranty and may result in malfunction or

mechanical failure that leads to serious

personal injury or death!

AWKWARD POSITIONS.

Keep proper footing and

balance at all times when operating machine.

Do not overreach! Avoid awkward hand

positions that make workpiece control difficult

or increase the risk of accidental injury.

CHILDREN & BYSTANDERS.

Keep children and

bystanders at a safe distance from the work

area. Stop using machine if they become a

distraction.

GUARDS & COVERS.

Guards and covers reduce

accidental contact with moving parts or flying

debris—make sure they are properly installed,

undamaged, and working correctly.

FORCING MACHINERY. Do not force machine. It

will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury may

occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement during

operation greatly increases risk of injury or

loss of control. Before starting, verify machine

is stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for

recommended accessories. Using improper

accessories will increase risk of serious injury.

UNATTENDED OPERATION. To reduce the risk

of accidental injury, turn machine OFF and

ensure all moving parts completely stop

before walking away. Never leave machine

running while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to

keep machine in good working condition. A

machine that is improperly maintained could

malfunction, leading to serious personal injury

or death.

CHECK DAMAGED PARTS. Regularly inspect

machine for any condition that may affect

safe operation. Immediately repair or replace

damaged or mis-adjusted parts before

operating machine.

MAINTAIN POWER CORDS. When disconnecting

cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the

cord may damage the wires inside, resulting

in a short. Do not handle cord/plug with wet

hands. Avoid cord damage by keeping it away

from heated surfaces, high traffic areas, harsh

chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the

intended operation, stop using the machine!

Contact Technical Support at (360) 734-3482.

Replaces Page 7

-4-

Model W1737/W1738 (Mfd. Since 1/14)

Additional Safety for Wide Belt Sanders

MINIMUM STOCK DIMENSION. To avoid kickback,

never sand workpieces below minimum

specifications listed in Data Sheet.

ADJUSTMENTS/MAINTENANCE. Make sure

machine is turned OFF, disconnected from

power and air, and all moving parts are

completely stopped before doing adjustments or

maintenance.

SANDING DUST. Sanding creates large amounts

of dust and flying chips that can lead to eye

injury or respiratory illness. Reduce risk of these

hazards by wearing approved eye and respiratory

protection when using sander.

DUST COLLECTION. Never operate without

adequate dust collection system in place and

running. Proper dust collection reduces dust in

work area, which decreases risk of long-term

respiratory damage, but it is not a substitute for

using a respirator.

Serious injury or death can occur from hands getting trapped between workpiece and conveyor

table, getting entangled in rotating parts inside machine, or lacerated by sanding drum.

Workpieces thrown by sander can strike nearby operators. Long-term respiratory damage can

occur from using sander without proper use of a respirator and an adequate dust collection

system. To minimize risk of getting hurt or killed, anyone operating machine MUST completely

heed hazards and warnings below.

FEEDING WORKPIECE. DO NOT place fingers

under bottom of workpiece while feeding it into

sander. Fingers can become pinched between

workpiece and conveyor.

ENTANGLEMENT HAZARDS. DO NOT wear loose

clothing, gloves, or jewelry, and tie back long

hair. Never reach inside operating machine or try

clearing jammed workpiece. Keep all guards in

place and secure, and all doors closed.

SANDING DRUM CONTACT. Rotating sandpaper

can remove a large amount of flesh in a few

seconds. Keep hands away from rotating sanding

drum(s) during operation. Never touch moving

sandpaper on purpose.

WORKPIECE KICKBACK. A workpiece can be

ejected out the front of sander at high rate of

speed, and hit operator or bystanders. Never

stand in-line with workpiece, never feed more

than one workpiece at a time, and always adjust

pressure rollers below sanding roller.

Replaces Page 8

-5-

Model W1737/W1738 (Mfd. Since 1/14)

Replaces Page 10

Availability

Before installing the machine, consider the availability

and proximity of the required power supply circuit. If an

existing circuit does not meet the requirements for this

machine, a new circuit must be installed. To minimize

the risk of electrocution, fire, or equipment damage,

installation work and electrical wiring must be done by

a qualified electrician in accordance with all applicable

codes and standards.

Full-Load Current Rating

The full-load current rating is the amperage a machine

draws at 100% of the rated output power. On machines

with multiple motors, this is the amperage drawn by the

largest motor or sum of all motors and electrical devices

that might operate at one time during normal operations.

W1737 Full-Load Current Rating at 230V ...... 57 Amps

W1738 Full-Load Current Rating at 230V ... 39.4 Amps

W1738 Full-Load Current Rating at 460V ... 19.7 Amps

The full-load current is not the maximum amount of amps

that the machine will draw. If the machine is overloaded,

it will draw additional amps beyond the full-load rating.

If the machine is overloaded for a sufficient length of

time, damage, overheating, or fire may result—especially

if connected to an undersized circuit. To reduce the

risk of these hazards, avoid overloading the machine

during operation and make sure it is connected to a

power supply circuit that meets the requirements in the

following section.

Electrocution, fire, or equipment

damage may occur if machine is not

correctly grounded and connected to

the power supply.

For your own safety and protection of

property, consult a qualified electrician

if you are unsure about wiring practices

or electrical codes in your area.

ELECTRICAL

A power supply circuit includes all electrical equipment

between the breaker box or fuse panel in the building

and the machine. The power supply circuit used for

this machine must be sized to safely handle the full-

load current drawn from the machine for an extended

period of time. (If this machine is connected to a circuit

protected by fuses, use a time delay fuse marked D.)

Circuit Information

-6-

Model W1737/W1738 (Mfd. Since 1/14)

Note: The circuit requirements listed in this

manual apply to a dedicated circuit—where

only one machine will be running at a

time. If this machine will be connected to

a shared circuit where multiple machines

will be running at the same time, consult

a qualified electrician to ensure that the

circuit is properly sized for safe operation.

Serious injury could occur if you con-

nect the machine to power before

completing the setup process. DO NOT

connect to power until instructed later

in this manual.

Power

Source

Locking

Disconnect Switch

Machine

Ground Ground

ConduitConduit

Figure 1. Typical setup of a permanently

connected machine.

Extension Cords

W1737 Circuit Requirements for 230V

Nominal Voltage ......................... 220V, 230V, 240V

Cycle ........................................................60 Hz

Phase .............................................. Single-Phase

Circuit Rating ......................................... 70 Amps

W1738 Circuit Requirements for 230V

Nominal Voltage ......................... 220V, 230V, 240V

Cycle ........................................................60 Hz

Phase .................................................... 3-Phase

Minimum Circuit Size ............................... 50 Amps

W1738 Circuit Requirements for 460V

Nominal Voltage ......................... 440V, 460V, 480V

Cycle ........................................................60 Hz

Phase .................................................... 3-Phase

Minimum Circuit Size ............................... 30 Amps

This machine must be permanently connected the power

supply for 460V operation. A disconnecting means, such

as a locking switch (see the figure to the right), must

be provided to allow the machine to be disconnected

(isolated) from the power supply when required. This

installation must be performed by a qualified electrician

in accordance with all applicable electrical codes and

ordinances.

Grounding Instructions

This machine must be grounded! In the event of a

malfunction or breakdown, grounding provides a path of

least resistance for electrical current to reduce the risk of

electric shock. A permanently connect machine must be

connected to a grounded metal permanent wiring system;

or to a system having an equipment-grounding conductor.

All grounds must be verified and rated for the electrical

requirements of the machine. Improper grounding can

increase the risk of electric shock!

In Addition to Page 10

This machine is prewired to operate on a 230V power

supply circuit that has a verified ground and meets the

following requirements:

This machine is prewired to operate on a 230V power

supply circuit that has a verified ground and meets the

following requirements:

This machine can be converted to operate on a 460V

power supply (refer to Voltage Conversion later in this

section). The intended 460V circuit must have a verified

ground and meet the following requirements:

Since this machine must be permanently

connected to the power supply, an

extension cord cannot be used.

-7-

Model W1737/W1738 (Mfd. Since 1/14)

440V Conversion (W1738)

This machine is prewired for 230V 3-phase power but has

the capability of operating on 460V power with a minor

conversion. The conversion consists of replacing two

overload relays and rewiring each of the three motors.

All wiring changes must be inspected by a qualified

electrician or service personnel before the machine is

connected to the power source.

Contact your local Shop Fox dealer to purchase the

440V conversion kit (P/N X1738038V2) that includes the

necessary two overload relays.

To convert Model W1738 to 460V operation, do these

steps:

1. DISCONNECT SANDER FROM POWER!

2. Open electrical cabinet on back of machine.

3. Remove wire labeled "1" at 220V terminal of trans-

former and connect it to 440V terminal (see Figures

6–7).

4. Replace thermal overload relays, as shown in

Figure 6.

5. Set LR3D325 amperage dial to 18A and LR3D07

amperage dial to 1.7A.

6. Re-wire sanding, conveyor, and table elevation

motors as shown in wiring diagrams on Page 34 of

owner's manual.

Figure 6. Locations of thermal overload

relays and transformer.

Replace with

LR3D325

Replace with

LR3D07

Transformer

200V 220V0V0V 440V

0

2

3

1

Figure 7. W1738 transformer re-wired for

460V operation.

Replaces Page 11

-8-

Model W1737/W1738 (Mfd. Since 1/14)

Replaces Page 21

Jet Air Flow

The air jet located at the air fork sends a stream of

air across the air fork and into the air stream receiver

(see Figure 23). As soon as the sanding belt obstructs

this stream of air, a piston changes the direction of belt

movement to the left. Your goal is to adjust this stream

of air so the system uses the least amount of air and yet

the machine still oscillates consistently.

To adjust the jet air flow, do these steps:

1. TURN OFF and LOCK your master power switch.

2. Adjust the air regulator to 70 PSI.

3. Open both upper access doors on the sander, loosen

the sanding belt tension, and slide the belt so the

air stream is unobstructed.

4. Loosen the jam nut and turn the jet adjustment

knob (Figure 24) clockwise until the air stream is

reduced to a minimum.

5. Turn the jet adjustment knob counterclockwise, and

use a piece of cardboard to alternately block and

unblock the air stream until the upper drum just

begins to react and move left and right.

6. Turn the jet adjustment knob counterclockwise an

additional

1

⁄2 turn and tighten the jam nut.

7. Complete Belt Tracking on Page 22.

Figure 23. Air Jet and air fork assembly.

Figure 24. Air Stream adjustment knob.

Air Stream

Receiver

Air Fork

Air Jet

Air Stream

Adjustment

Knob

Lock

Lever

Height

Lever

Scale and

Pointer

Using the Platen

The platen controls (Figure 25) on your sander allow for

three basic types of sanding. Note: The platen scale is

broken down in millimeter increments, and is for only

reduced-platen sanding depth positions. For aggressive

sanding, retract the platen to the Platen Up position,

adjust the table, and let the drums make the deep cut.

Platen Up — The platen is above the level of the sanding

rollers, so the front roller removes large amounts of

material quickly, but leaves a rough finish.

Platen Even — The platen is even with the sanding

rollers, so the rollers work together with the platen to

produce intermediate/final finishing.

Platen Down — The platen is 0.2mm below the sanding

rollers, so the platen gives a smooth and feathered

finish. Avoid lowering the platen more than 0.2mm below

the sanding belt rollers.

Figure 25. Platen controls.

-9-

Model W1737/W1738 (Mfd. Since 1/14)

W1737 & W1738 Control Panel Wiring

Replaces Page 35

AMP DRAW

METER

SANDING MOTOR

START

BUTTON

SANDING MOTOR

STOP

BUTTON

DIGITAL

PANEL

FEED MOTOR

START

BUTTON

FEED MOTOR

STOP

BUTTON

EMERGENCY

SHUT-OFF

BUTTON

POWER

LAMP

-10-

Model W1737/W1738 (Mfd. Since 1/14)

W1737 General Wiring Diagram

Replaces Page 36

-11-

Model W1737/W1738 (Mfd. Since 1/14)

Replaces Page 37

W1738 General Wiring Diagram

-12-

Model W1737/W1738 (Mfd. Since 1/14)

W1738 Electrical Cabinet Wiring

Replaces Page 39

-13-

Model W1737/W1738 (Mfd. Since 1/14)

Replaces Page 40

W1737 Electrical Box Component Locations

Sanding

Motor

Contactor

Feed Motor

Contactor

Amp Meter

Current Sensor

Emergency Brake

Contactor

Sanding Belt

Overload Relay

4 Amp

Fuses

Power Supply

Terminal Bar

UP/DOWN Table Motor

Contactors

Feed Motor

Overload Relay

-14-

Model W1737/W1738 (Mfd. Since 1/14)

W1737 Electrical Cabinet Wiring

Replaces Page 41

-15-

Model W1737/W1738 (Mfd. Since 1/14)

Electrical Parts

Replaces Page 42

6

7

17

15

16

37

31

34

8

14V2

36

33

2V2

12

12-1

12

4V2

5V2 (W1738 Only)

5V2 (W1737 Only)

11-1 (W1738 440V

Conversion Only)

3V3

3-1V2 (W1738 440V

Conversion Only)

11

1

24

21

18

35

20

26

23

10

31

9

39

25

27V2 (W1738 Only)

38 (W1737 Only)

-16-

Model W1737/W1738 (Mfd. Since 1/14)

Electrical Parts List

Replaces Page 43

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 X1737001 CURRENT SENSOR 14V2 X1738014V2 TERMINAL BAR V2.10.09 (W1738)

2V2 X1737002V2 CONTACTOR SCHN LC1D50A V2.03.11 15 X1737015 PU CONNECTOR 1/2

(W1737) 16 X1737016 PU CONNECTOR 3/4

2V2 X1738002V2 CONTACTOR SCHN LC1D40A V2.03.11 17 X1737017 CABLE CONNECTOR 1"

(W1738) 18 X1737018 DIGITAL AMP METER

3V3 X1738003V3 OL RELAY SCHN LRD340 30-40A 20 X1737020 START SWITCH

V3.04.13 (W1738) 21 X1737021 STOP SWITCH

4V2 X1737004V2 FUSE 4A 10 X 38MM V2.03.11 23 X1737023 POWER INDICATION LIGHT

5V2

X1737005V2

TERMINAL BLOCK V2.10.09 (W1737) 24 X1737024 EMERGENCY STOP SWITCH

5V2

X1738005V2

TERMINAL BLOCK V2.10.09 (W1738) 25 X1737025 WIRE COLUMN

6 X1737006 ELECTRICAL CONTROL BOX 26 X1737026 COMPUTER

7 X1737007 HINGE 27V2 X1738027V2 TRANSFORMER 3PH V2.10.09 (W1738)

8 X1737008 DOOR 31 XPLW02 LOCK WASHER 1/4

9 X1737009 BASE PLATE 33 XPN05 HEX NUT 1/4-20

10 X1737010 CONTROL PANEL 34 XPS04 PHLP HD SCR 1/4-20 X 1/2

11 X1737011 OL RELAY SCHN LR3D12 5.5-8A (W1737) 35 XPS07M PHLP HD SCR M4-.7 X 8

11 X1738011 OL RELAY SCHN LR3D08 2.5-4A (W1738) 36 XPS51M PHLP HD SCR M4-.7 X 30

12 X1737012 CONTACTOR SCHN LC1D09 37 XPW06 FLAT WASHER 1/4

12-1 X1737012-1 CONTACTOR SCHN LC1D09 W/LOCK 38 X1689624 OL RELAY SCHN LT47 5-60A (W1737)

14V2 X1737014V2 TERMINAL BAR V2.10.09 (W1737) 39 X1737039 FUSE HOLDER SCHN DF101 10 X 38MM

W1738 440V CONVERSION KIT

3-1V2 X1738003-1V2 OL RELAY SCHN LR3D325 17-25A

V2.03.11 (W1738)

11-1 X1738011-1 OL RELAY SCHN LR3D07 1.6-2.5A

(W1738)

38V2 X1738038V2

440V CONVERSION KIT V2.03.11

-17-

Model W1737/W1738 (Mfd. Since 1/14)

New Upper Roller Air Cylinder

562

569

567

503V2

513

568

Previous Version Oscillation

Diaphragm Assembly (P/N 503)

New Version Air Cylinder (P/N 503V2)

REF PART # DESCRIPTION REF PART # DESCRIPTION

503V2 X1737503V2 OSCILLATION AIR CYLINDER V2.01.14 567 X1737567 HEX BOLT 5/16-18 X 1-1/2

513 X1737513 LOCK WASHER 5/16 568 X1737568 HEX NUT 5/16-18

562 X1737562 UNIVERSAL JOINT FORK 569 X1737569 CONNECTOR 1/4N X 1/8T X 90 DEG

In Addition to Pages 52–53

-18-

Model W1737/W1738 (Mfd. Since 1/14)

Air System Parts

Replaces Page 54

IN

616

617

618

619

620

621

615

626

627

628

629

630

632

633

625

627

634

603

601

602

603

604

605

606

636

608

609

610

611

612

613

614

632

607

622

624

-19-

Model W1737/W1738 (Mfd. Since 1/14)

Air System Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

601 X1737601 AIR SWITCH 1/8 618 X1737618 CONNECTOR 5/16N X 1/4T

602 X1737602 CONNECTOR 1/4N X 1/8T 619 X1737619 8MM FLEXIBLE HOSE

603 X1737603 CONNECTOR 1/4N X 1/8T 90º 620 X1737620 AIR SWITCH 1/4

604 X1737604 BUFFER (BRONZE) 621 X1737621 ELBOW 1/4T x 1/4T 90º

605 X1737605 CONNECTOR 5/16N X 1/8T 90º 622 X1737622 SOLENOID VALVE

606 X1737606 8MM FLEXIBLE HOSE 624 X1737624 THROTTLE VALVE 1/8

607 X1737607 8MM FLEXIBLE HOSE 625 X1737625 CONNECTOR 5/16N X 1/4T

608 X1737608 6MM FLEXIBLE HOSE 626 X1737626 MANIFOLD

609 X1737609 6MM FLEXIBLE HOSE 627 X1737627 CONNECTOR 1/4N X 1/4T

610 X1737610 6MM FLEXIBLE HOSE 628 X1737628 BRONZE ELBOW 1/4T X 1/8T 90º

611 X1737611 6MM FLEXIBLE HOSE 629 X1737629 CONNECTOR 1/4N X 1/8T 90º

612 X1737612 6MM FLEXIBLE HOSE 630 X1737630 CONNECTOR 1/4N X 1/8T 90º

613 X1737613 6MM FLEXIBLE HOSE 632 X1737632 CONNECTOR 1/4N X 1/8T

614 X1737614 6MM FLEXIBLE HOSE 633 X1737633 BRONZE CONNECTOR 1/4N

615 XPS22 PHLP HD SCR 10-24 x 5/8 634 X1737634 CONNECTOR 1/4N X 3/8T

616 X1737616 PRESSURE REGULATOR 636 X1737636 8MM FLEXIBLE HOSE

617 X1737617 PSI GAUGE

Replaces Page 55

-20-

Model W1737/W1738 (Mfd. Since 1/14)

717

759

760

712

700

710

758

728

701

729

703

757

714

709

706

742

736

719

702

741

743

744

738

740

725

737

739

702

719

736

742

706

722

726

747

749

748

707

727

711

751

752

754

755

745

746

753

716

750

725

723

756

732

705

731

733

724

735

712

70 8

734

704

730

718

720

715

Replaces Page 56

Sanding Drum and Roller Parts

Page is loading ...

Woodstock SHOP FOX W1738 Owner's manual

This manual is also suitable for

Woodstock SHOP FOX W1738 Owner's manual

Related papers

Other documents