Cross Technologies 2116-34 Owner's manual

Brand: Cross Technologies

Model: 2116-34

Type: Owner's manual

Instruction Manual

Model 2116-34

Block Downconverter

September 2009 Rev. D

MODEL 2116

CROSS TECHNOLOGIES INC.

POWER

DOWNCONVERTER

EXT

10MHZ

ALARM

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment. Printed in USA.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 2116-34 Downconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

2.0 Installation 5

2.1 Mechanical 5

2.2 Rear Inputs and Outputs 6

2.3 Front Panel Indicators 6

2.4 Operation 7

3.0 Environmental Use Information 8

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2116-34 Manual, Rev. D Page 2 9/15/09

MODEL 2116-34 Downconverter

1.0 General

1.1 Equipment Description - The 2116-34 Downconverter converts 3.4 - 4.2 GHz to 0.95 - 1.75 GHz with

low phase noise and flat frequency response. Frequency translation is via a 5.15 GHz local oscillator. Front

panel LEDs provide indication of DC Power, External 10 MHz, and PLL Alarm. The gain is +35 dB.

Connectors are Type N female for the RF and BNC female for the L-Band and external reference input and

reference output. A three-way switch controls which 10 MHz reference is being used. In the INT position, the

internal reference is used, in the EXT position, the external reference is used, and in the AUTO position, the

internal reference is used unless a 3 dBm ± 3 dB, 10MHz reference signal is connected to the external reference

input. The 2116 is powered by a 100-240 ± 10% VAC power supply, and mounted in a 1 3/4” X 19” X 14”

rack mount chassis.

MODEL 2116

CROSS TECHNOLOGIES INC.

POWER

DOWNCONVERTER

EXT

10MHZ

ALARM

FRONT PANEL

GND

EXT 10 MHz

RF INPUT

INPUT

10 MHz REF

OUTPUT

INT EXT

AUTO

S1 J1

L-BAND

OUTPUT

J101

J11

ALARM

15 234

REAR PANEL

FIGURE 1.1 Model 2116-34 Front and Rear Panels

3.4

4.2

GHz

0.95

1.75

GHz

OUT

5.15

GHz

3.4 to 4.2

GHz BP

EXT 10 MHz

10 MHZ

MON

2 GHz LP

AUTO

INT 10

MHz

FIGURE 1.2 Model 2116-34 Downconverter Block Diagram

2116-34 Manual, Rev. D Page 3 9/15/09

1.2 Technical Characteristics

TABLE 1.0 2116-34 Downconverter Specifications*

Input Characteristics

Impedance/Return Loss 50  /14 dB (see TABLE 2.2 for connector options)

Frequency 3.4 to 4.2 GHz

Noise Figure, max. 20 dB, max. gain

Input Level -55 to -35 dBm

Input 1dB Compression -25 dBm

Output Characteristics

Impedance/Return Loss 50 /14 dB (see TABLE 2.2 for connector options)

Frequency 0.95 to 1.75 GHz

Output Level Range -20 to 0 dBm

Output 1dB Compression +10 dBm

Channel Characteristics

Gain +35 dB ± 2 dB

Image Rejection >60 dB, min.

Spurious, Inband SIGNAL RELATED <-60 dBC (0 dBm output level)

SIGNAL INDEPENDENT <-60 dBm

Spurious, Out of Band <-50 dBC

Frequency Response ±1.5 dB, 0.95 to 1.75 GHz out; ± 0.5 dB, 40 MHz BW

Frequency Sense Inverting

LO Characteristics

LO Frequency 5.15 GHz

Frequency Accuracy ± 0.01 ppm max. over temp internal reference

Phase Noise (dBC/Hz) < -70 @ 100 Hz; < -80 @ 1 kHz; < -90 @ 10 kHz

< -100 @ 100 kHz; < -110 @ 1 MHz

10 MHz Level 0 dBm, ± 3 dB, 75 ohms, External In or 10MHz Out

Controls, Indicators

Power Green LED

PLL Alarm Red LED, External contact closure

Ext 10 MHz Yellow LED, Indicates Ext 10 MHz reference is active

Other

RF Connector Type N, 50, female (see TABLE 2.2 for other options)

L-Band Connector BNC, 50, female (see TABLE 2.2 for other options)

Ext 10 MHz Connector BNC, 75, female

10 MHz Monitor Connector BNC, 75, female

Connector, Alarm DB9, female - NO or NC contact closure on Alarm

Size 19 inch, 1RU standard chassis 1.75” high X 14.0” deep

Power 100-240 ± 10% VAC, 47-63 Hz, 45 watts max.

Options

Connector options see TABLE 2.2

*+10˚C to +40˚C; Specifications subject to change without notice.

2116-34 Manual, Rev. D Page 4 9/15/09

2.0 Installation

2.1 Mechanical - The 2116-34 consists of one RF PCB housed in a 1 RU (1 3/4 inch high) by 12 inch deep

chassis. A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies. The 2116-34 can be

secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the 2116-34 is assembled.

PS IN

PIN 1, +12 VDC

PIN 2, +5 VDC

PIN 3, +5 VDC

PIN 4, GROUND

PIN 5, GROUND

PIN 6, -12 VDC

PIN 7, +24 VDC

PIN 8, +24 VDC

POWER

SUPPLY

J10

J101 - Panel Mount

Type N Connector

BP FILTER/

ISOLATOR

FIGURE 2.0 2116-34 Mechanical Assembly

2116-34 Manual, Rev. D Page 5 9/15/09

2.2 Rear Panel Input/Output Signals - Figure 2.1 shows the input and output connectors on the rear panel.

15 234

GND

EXT 10 MHz

RF INPUT

INPUT

10 MHz REF

OUTPUT

INT EXT

AUTO

S1 J1

L-BAND

OUTPUT

J101

J11

ALARM

J1 - L-BAND OUTPUT

BNC (female) 50 . 0.95 to 1.75 GHz, 0

dBm max. input signal. See Table 2.2

for other connector options.

AC INPUT

100-240 ±10% VAC,

47-60 HZ

Uses 2 amp Slow Blo, 5

mm fuse

S1 - 10 MHz SWITCH

3-position switch. INT selects internal 10MHz ref.

AUTO selects internal 10MHz ref, unless a 0dBm

±3dB 10MHz signal is inserted on J2. EXT selects

external 10MHz ref from J2.

J1 - EXT 10 MHz INPUT

BNC (female) 75 . Insert external 10MHz

reference here (3 dBm ± 3 dB).

J101 - RF INPUT

Type N (female) 50 . 3.4 to

4.2 GHz, -35 dBm max. input

signal. See Table 2.2 for other

connector options.

J11 - ALARM

DB9 (female) connector.

See Table 2.1.

J8 - 10 MHz REF OUTPUT

BNC (female) 75 . Outputs currently

selected 10MHz ref signal (3 dBm ±3 dB).

FIGURE 2.1 2116-34 Rear Panel I/Os

TABLE 2.1 JJ11

TABLE 2.1 J11 Pinouts (DB9)

Pin Function

1Not Used

2Not Used

3Not Used

4Not Used

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8Not Used

9 Alarm Relay: Normally Closed

TABLE 2.2 Connect

Connector Options

L-Band RF

BNC, 50 (STD) Type N, 50 (STD)

BNC, 75 SMA, 50

Type F, 75

Type N, 50

2.3 Front Panel Indicators -The following are the front panel indicators.

DS2 - ALARM LED

Lights RED when

PLL comes out of lock.

DS1 - POWER LED A

Lights GREEN when DC voltage is

present from AC power supply.

DS3 - EXT 10 MHz LED

Lights YELLOW when external

10MHz reference is active.

POWER

EXT

MHz

ALARM

FIGURE 2.2 2116-34 Front Panel Controls and Indicators

2116-34 Manual, Rev. D Page 6 9/15/09

2.4 Installation / Operation

2.4.1 Installing and Operating the 2116-34 Downconverter

1.) Connect a -55 dBm to -35 dBm signal to RF INPUT, J101 (Figure 2.1).

2.) Connect the L-BAND OUTPUT, J1, to the external equipment.

3.) Connect 100-240 ± 10% VAC, 47 - 63 Hz to AC connector on the back panel.

4.) Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.2).

5.) Select either INT (for internal 10MHz ref), AUTO (for internal 10MHz ref UNLESS a external

10MHz, 0 dBm signal is connected to J2), or EXT (for external 10MHz, 0 dBm ref that is inserted

at J2) on rear panel switch S1 (Figure 2.1).

6.) If EXT is selected or AUTO is selected and there is a 10MHz, 0 dBm signal at J2, check that DS3

(yellow, Ext 10 MHz) is on (Figure 2.2).

7.) Check that a 10MHz, 0 dBm ±3 dB signal is present at the 10 MHz REF OUTPUT (J8)

(Figure 2.1).

8.) AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in

the drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot. If a

fuse continues to open, the power supply is most likely defective.

FUSE DRAWER

SPARE FUSE DRAWER

AC Fuse - 2 amp slow blow (Type T),

5 mm X 20 mm

INPUT

100-240± 10%VAC

47-63 Hz

2A MAX

FUSE

TYPE T 2A GDC

250 VOLT

FOR 100 - 240 V~

FIGURE 2.3 Fuse Location and Spare Fuse

2116-34 Manual, Rev. D Page 7 9/15/09

3.0 Environmental Use Information

A. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C. Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.

Particular attention should be given to supply connections other than direct connection to the

Branch (use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2116-34 Manual, Rev. D Page 8 9/15/09

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

Printed in USA

2116-34 Manual, Rev. D Page 9 9/15/09

Cross Technologies 2116-34 Owner's manual

Cross Technologies 2116-34 Owner's manual

Cross Technologies 2116-34 Owner's manual

Related papers