Vega POINTRAC 31 Operating instructions

Operating Instructions

Radiometric sensor for level detection

POINTRAC 31

Four-wire 8/16 mA/HART

Document ID: 39411

2

Contents

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

Contents

1 About this document ............................................................................................................... 4

1.1 Function ........................................................................................................................... 4

1.2 Target group ..................................................................................................................... 4

1.3 Symbols used................................................................................................................... 4

2 For your safety ......................................................................................................................... 5

2.1 Authorised personnel ....................................................................................................... 5

2.2 Appropriate use ................................................................................................................ 5

2.3 Warning about incorrect use ............................................................................................. 5

2.4 General safety instructions ............................................................................................... 5

2.5 EU conformity ................................................................................................................... 6

2.6 NAMUR recommendations .............................................................................................. 6

2.7 Installation and operation in the USA and Canada ........................................................... 6

2.8 Environmental instructions ............................................................................................... 6

3 Product description ................................................................................................................. 7

3.1 Conguration .................................................................................................................... 7

3.2 Principle of operation........................................................................................................ 8

3.3 Packaging, transport and storage ..................................................................................... 8

3.4 Accessories...................................................................................................................... 9

3.5 Corresponding source container .................................................................................... 11

4 Mounting ................................................................................................................................. 13

4.1 General instructions ....................................................................................................... 13

4.2 Mounting instructions ..................................................................................................... 14

5 Connecting to power supply ................................................................................................. 20

5.1 Preparing the connection ............................................................................................... 20

5.2 Connection ..................................................................................................................... 23

6 Set up with the display and adjustment module ................................................................ 26

6.1 Insert display and adjustment module ............................................................................ 26

6.2 Adjustment system ......................................................................................................... 27

6.3 Parameter adjustment .................................................................................................... 28

6.4 Saving the parameterisation data ................................................................................... 39

7 Setup with PACTware ............................................................................................................. 40

7.1 Connect the PC .............................................................................................................. 40

7.2 Parameter adjustment with PACTware ............................................................................ 41

7.3 Saving the parameterisation data ................................................................................... 42

8 Set up with other systems .................................................................................................... 43

8.1 DD adjustment programs ............................................................................................... 43

8.2 Field Communicator 375, 475 ........................................................................................ 43

9 Diagnostics and servicing .................................................................................................... 44

9.1 Maintenance .................................................................................................................. 44

9.2 Status messages ............................................................................................................ 44

9.3 Rectify faults ................................................................................................................... 46

9.4 Exchanging the electronics module ................................................................................ 47

9.5 Software update ............................................................................................................. 48

9.6 How to proceed if a repair is necessary .......................................................................... 48

3

Contents

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

10 Dismount................................................................................................................................. 50

10.1 Dismounting steps.......................................................................................................... 50

10.2 Disposal ......................................................................................................................... 50

11 Supplement ............................................................................................................................ 51

11.1 Technical data ................................................................................................................ 51

11.2 Dimensions .................................................................................................................... 55

11.3 Industrial property rights ................................................................................................. 60

11.4 Trademark ...................................................................................................................... 60

Safety instructions for Ex areas

TakenoteoftheExspecicsafetyinstructionsforExapplications.

These instructions are attached as documents to each instrument

with Ex approval and are part of the operating instructions.

Editing status: 2020-05-12

4

1 About this document

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

1 About this document

1.1 Function

This instruction provides all the information you need for mounting,

connection and setup as well as important instructions for mainte-

nance,faultrectication,theexchangeofpartsandthesafetyofthe

user. Please read this information before putting the instrument into

operation and keep this manual accessible in the immediate vicinity

of the device.

1.2 Target group

This operating instructions manual is directed to trained personnel.

Thecontentsofthismanualmustbemadeavailabletothequalied

personnel and implemented.

1.3 Symbols used

Document ID

This symbol on the front page of this instruction refers to the Docu-

ment ID. By entering the Document ID on www.vega.com you will

reach the document download.

Information, note, tip: This symbol indicates helpful additional infor-

mation and tips for successful work.

Note: This symbol indicates notes to prevent failures, malfunctions,

damage to devices or plants.

Caution: Non-observance of the information marked with this symbol

may result in personal injury.

Warning: Non-observance of the information marked with this symbol

may result in serious or fatal personal injury.

Danger: Non-observance of the information marked with this symbol

results in serious or fatal personal injury.

Ex applications

This symbol indicates special instructions for Ex applications.

•

List

The dot set in front indicates a list with no implied sequence.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

5

2 For your safety

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

2 For your safety

2.1 Authorised personnel

All operations described in this documentation must be carried out

onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.

During work on and with the device, the required personal protective

equipment must always be worn.

2.2 Appropriate use

The POINTRAC 31 is a sensor for point level detection.

Youcannddetailedinformationabouttheareaofapplicationin

chapter "Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

2.3 Warning about incorrect use

Inappropriate or incorrect use of this product can give rise to applica-

tion-specichazards,e.g.vesseloverllthroughincorrectmounting

or adjustment. Damage to property and persons or environmental

contamination can result. Also, the protective characteristics of the

instrument can be impaired.

2.4 General safety instructions

This is a state-of-the-art instrument complying with all prevailing

regulations and directives. The instrument must only be operated in a

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressive or corrosive media that can cause a dangerous situation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

The safety instructions in this operating instructions manual, the na-

tional installation standards as well as the valid safety regulations and

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

To avoid any danger, the safety approval markings and safety tips on

the device must also be observed.

This measuring system uses gamma rays. Therefore take note of the

instructions for radiation protection in chapter "Product description".

Any work on the source container may only be carried out under the

supervisionofaqualiedradiationprotectionocer.

6

2 For your safety

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

2.5 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmtheconformityofthe

instrument with these directives.

The EU conformity declaration can be found on our homepage.

Electromagnetic compatibility

Instruments in four-wire or Ex-d-ia version are designed for use in an

industrial environment. Nevertheless, electromagnetic interference

from electrical conductors and radiated emissions must be taken into

account, as is usual with class A instruments according to EN 61326-

1.Iftheinstrumentisusedinadierentenvironment,theelectromag-

netic compatibility to other instruments must be ensured by suitable

measures.

2.6 NAMUR recommendations

NAMUR is the automation technology user association in the process

industry in Germany. The published NAMUR recommendations are

acceptedasthestandardineldinstrumentation.

ThedevicefullstherequirementsofthefollowingNAMURrecom-

mendations:

•

NE 21 – Electromagnetic compatibility of equipment

•

NE 43 – Signal level for fault information from measuring transduc-

ers

•

NE53–Compatibilityofelddevicesanddisplay/adjustment

components

•

NE107–Self-monitoringanddiagnosisofelddevices

For further information see www.namur.de.

2.7 Installation and operation in the USA and

Canada

This information is only valid for USA and Canada. Hence the follow-

ing text is only available in the English language.

Installations in the US shall comply with the relevant requirements of

the National Electrical Code (ANSI/NFPA 70).

Installations in Canada shall comply with the relevant requirements of

the Canadian Electrical Code.

2.8 Environmental instructions

Protection of the environment is one of our most important duties.

That is why we have introduced an environment management system

with the goal of continuously improving company environmental pro-

tection.Theenvironmentmanagementsystemiscertiedaccording

to DIN EN ISO 14001.

Pleasehelpusfullthisobligationbyobservingtheenvironmental

instructions in this manual:

•

Chapter "Packaging, transport and storage"

•

Chapter "Disposal"

7

3 Product description

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

3 Product description

3.1 Conguration

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument:

2

9

10

4

5

3

6

7

8

9

1

Fig. 1: Layout of the type label (example)

1 Instrument type

2 Product code

3 Electronics

4 Protection rating

5 Process and ambient temperature, process pressure

6 Instrument length

7 Hardware and software version

8 Order number

9 Serial number of the instrument

10 ID numbers, instrument documentation

The type label contains the serial number of the instrument. With it

youcanndthefollowinginstrumentdataonourhomepage:

•

Product code (HTML)

•

Delivery date (HTML)

•

Order-specicinstrumentfeatures(HTML)

•

Operating instructions and quick setup guide at the time of ship-

ment (PDF)

•

Order-specicsensordataforanelectronicsexchange(XML)

•

Testcerticate(PDF)-optional

Move to "www.vega.com"andenterinthesearcheldtheserial

number of your instrument.

Alternatively, you can access the data via your smartphone:

•

Download the VEGA Tools app from the "Apple App Store" or the

"Google Play Store"

•

Scan the DataMatrix code on the type label of the instrument or

•

Enter the serial number manually in the app

This operating instructions manual applies to the following instrument

versions:

•

Hardware from 1.0.6

•

Software from 2.1.0

Type label

Serial number - Instru-

ment search

Scope of this operating

instructions

8

3 Product description

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

Theinstrumentisavailableindierentelectronicsversions.Eachver-

sioncanbeidentiedviatheproductcodeonthetypelabel:

•

StandardelectronicstypePROTRACH.-XX

The scope of delivery encompasses:

•

Radiometric sensor

•

Mounting accessories

•

Documentation

•

Bluetooth module (optional)

– This operating instructions manual

– Ex-specic"Safety instructions" (with Ex versions)

– Ifnecessary,furthercerticates

3.2 Principle of operation

The instrument is suitable for applications in liquids and bulk solids in

vesselsunderdicultprocessconditions.Thereareapplicationpos-

sibilities in nearly all areas of industry.

The limit level is detected contactlessly through the vessel wall. Nei-

theraprocessttingnoravesselopeningisrequired.Theinstrument

isthusidealforretrotting.

In radiometric measurement, a Caesium-137 or Cobalt-60 isotope

emits focussed gamma rays that are attenuated when penetrating

the vessel wall and the medium. The PVT detector on the opposite

side of the tank receives the radiation. When the intensity of the

radiationdropsbelowadenedvalue,e.g.duetodamping,thenthe

POINTRAC 31 switches. The measuring principle has proven itself

well under extreme conditions because it measures contactlessly

from outside through the vessel wall. The measuring system ensures

maximum safety, reliability and plant availability independent of the

medium and its properties.

3.3 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.

The packaging consists of environment-friendly, recyclable card-

board. For special versions, PE foam or PE foil is also used. Dispose

of the packaging material via specialised recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Electronics versions

Scope of delivery

Application area

Functional principle

Packaging

Transport

Transport inspection

9

3 Product description

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

•

Storage and transport temperature see chapter "Supplement -

Technical data - Ambient conditions"

•

Relative humidity 20 … 85 %

With instrument weights of more than 18 kg (39.68 lbs) suitable and

approved equipment must be used for lifting and carrying.

3.4 Accessories

The display and adjustment module is used for measured value indi-

cation, adjustment and diagnosis.

The integrated Bluetooth module (optional) enables wireless adjust-

ment via standard adjustment devices.

The interface adapter VEGACONNECT enables the connection of

communication-capable instruments to the USB interface of a PC.

The VEGADIS 81 is an external display and adjustment unit for VEGA

plics

®

sensors.

VEGADIS 82 is suitable for measured value indication and adjustment

of sensors with HART protocol. It is looped into the 4 … 20 mA/HART

signal cable.

The VEGADIS 62 is suitable for measured value indication of sensors.

It is looped into the 4 … 20 mA/HART signal cable.

The electronics module PT30… is a replacement part for radiometric

sensors POINTRAC 31.

It is located in the large electronics and connection compartment.

The electronics module can only be exchanged by VEGA service

technician.

The supplementary electronics module PROTRAC.ZE… is a replace-

ment part for radiometric sensors POINTRAC 31.

It is located in the lateral adjustment and connection compartment.

The radiometric sensor has temperature limits which must not be

exceeded. In case the max. permissible temperature is exceeded,

Storage

Storage and transport

temperature

Lifting and carrying

PLICSCOM

VEGACONNECT

VEGADIS 81

VEGADIS 82

External indicating unit

Electronics module -

PT30

Supplementary electron-

ics module - PROTRAC.

ZE

Device cooling

10

3 Product description

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

faulty measurements and a permanent damage of the sensor can be

caused.

You have several possibilities to avoid too high ambient temperatures:

Passive sun shade

Direct sun increases the temperature on the sensor by 20 °K. The

bestpossibilitytoprotectthesensoragainsttheeectsofdirectsun

is a suitable roof structure.

Ifthisisnotpossibleoronlywithgreateort,thenyoucanusethe

passive sun shade. The passive sun shade consists of a housing sun

shade and a sun protection hose and can reduce the sensor tempera-

ture by 10 °K.

Air cooling

For ambient temperatures up to +80 °C you can use an air cooling.

The cooling air is generated with vortex coolers. Please check if suf-

cientcompressedairisavailable.Youcanndfurtherinformation

in the supplementary instructions of the air cooling. The air cooling

cannotberetrotted.

Water cooling

For ambient temperatures up to +100 °C you can use a water cool-

ing.Pleasecheckifsucientcooledwaterisavailable.Youcannd

further information in the supplementary instructions of the water

cooling.Thewatercoolingcannotberetrotted.

In order to exclude external interference radiation, you can mount a

gamma modulator in front of the source holder. This allows reliable

measurement even when interference radiation occurs.

Gamma modulator

11

3 Product description

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

Fig. 2: Gamma modulator (optional) for uninterrupted measurement even with

interference radiation

1 Gamma modulator (mounted on the source holder)

For ambient temperatures up to 120 °C (248 °C) the gamma modula-

tor is optionally available with water cooling.

Anynumberofdevicescanbesynchronized.Tosynchronizeseveral

gamma modulators, you need a controller.

3.5 Corresponding source container

A radioactive isotope in a suitable source holder is the prerequisite for

a radiometric measurement setup.

The handling of radioactive substances is regulated by law. The radia-

tion protection rules of the country in which the system is operated

applyrstandforemost.

In Germany, for example, the current radiation protection ordinance

(StrlSchV) based on the Atomic Energy Law (AtG) applies.

The following points are important for measurement with radiometric

methods:

A handling permit is required for operation of a system using gamma

rays.Thispermitisissuedbytherespectivegovernmentoceorthe

responsibleauthority(inGermany,forexample,ocesforenviron-

mental protection, trade supervisory boards, etc.)

Youcanndfurtherinstructionsintheoperatinginstructionsmanual

of the source container.

Handling permit

12

3 Product description

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

When handling radioactive sources, unnecessary radiation exposure

must be avoided. An unavoidable radiation exposure must be kept as

low as possible. Take note of the following three important measures:

1 2 3

Fig. 3: Measures for protection against radioactive radiation

1 Shielding

2 Time

3 Distance

Shielding: Provide good shielding between the source and your-

self as well as all other persons. Special source containers (e.g.

VEGASOURCE) as well as all materials with high density (e.g. lead,

iron,concrete,etc.)provideeectiveshielding.

Time: Stay as short a time as possible in radiation exposed areas.

Distance: Your distance to the source should be as large as possible.

The local dose rate of the radiation decreases in proportion to the

square of the distance to the radiation source.

Theplantoperatormustappointaradiationsafetyocerwiththe

necessary expert knowledge. He is responsible for ensuring that the

radiation protection ordinance is complied with and for implementing

all radiation protection measures.

Control areas are areas in which the local dose rate exceeds a certain

value.Onlypersonswhoundergoocialdosemonitoringareallowed

intothesecontrolareas.Youcanndtherespectivelyvalidlimitvalues

for control areas in the guideline of the respective authority (in Ger-

many, for example, the radiation protection ordinance).

We are at your disposal for further information concerning radiation

protection and regulations in other countries.

General instructions for

radiation protection

Radiationsafetyocer

Control area

13

4 Mounting

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

4 Mounting

4.1 General instructions

The source container is part of the measuring system. In case the

source container is already equipped with an active isotope, the

source container must be locked before mounting.

Danger:

Before mounting; make sure that the source is securely closed. Use

a padlock to secure the source container in the closed condition and

prevent it from being inadvertently opened.

Protect your instrument against moisture ingress through the following

measures:

•

Use a suitable connection cable (see chapter "Connecting to

power supply")

•

Tighten the cable gland or plug connector

•

Lead the connection cable downward in front of the cable entry or

plug connector

This applies mainly to outdoor installations, in areas where high

humidity is expected (e.g. through cleaning processes) and on cooled

or heated vessels.

Note:

Makesurethatthedegreeofcontaminationspeciedinchapter

"Technical data" meets the existing ambient conditions.

Note:

Make sure that during installation or maintenance no moisture or dirt

can get inside the instrument.

To maintain the housing protection, make sure that the housing lid is

closed during operation and locked, if necessary.

Note:

For safety reasons, the instrument must only be operated within the

permissibleprocessconditions.Youcannddetailedinformationon

the process conditions in chapter "Technical data" of the operating

instructions or on the type label.

Hence make sure before mounting that all parts of the instrument ex-

posed to the process are suitable for the existing process conditions.

These are mainly:

•

Active measuring component

•

Processtting

•

Process seal

Process conditions in particular are:

•

Process pressure

•

Process temperature

•

Chemical properties of the medium

•

Abrasionandmechanicalinuences

Switchosource

Protection against mois-

ture

Process conditions

14

4 Mounting

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

Metric threads

In the case of instrument housings with metric thread, the cable

glands are screwed in at the factory. They are sealed with plastic

plugs as transport protection.

You have to remove these plugs before electrical connection.

NPT thread

In the case of instrument housings with self-sealing NPT threads, it is

not possible to have the cable entries screwed in at the factory. The

free openings for the cable glands are therefore covered with red dust

protection caps as transport protection.

Prior to setup you have to replace these protective caps with ap-

proved cable glands or close the openings with suitable blind plugs.

The suitable cable glands and blind plugs come with the instrument.

4.2 Mounting instructions

Note:

During the planning, our specialists will analyse the conditions of the

measurement loop to dimension the isotope accordingly.

Yougeta"SourceSizing"documentspecifyingtherequiredsource

activity and containing all relevant mounting information for your

measuring point.

Youmustfollowtheinstructionsinthis"SourceSizing"documentin

addition to the following mounting instructions.

The following mounting information is applicable as long as there is

nothingelsespeciedinthe"SourceSizing"document.

Cable glands

Installation position

15

4 Mounting

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

2

1

Fig. 4: Mounting position - level detection - version with detector tube

1 Vertical mounting

2 Mounting horizontally, at right angles to container

16

4 Mounting

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

3

2

1

Fig. 5: Mounting position - level detection - version without detector tube

1 Horizontal mounting

2 Vertical mounting

3 Mounting horizontally, at right angles to container

Youcanndinformationonprotectivebarriersandthemounting

of the corresponding source container in the operating instructions

manual of the source container, e.g. VEGASOURCE.

Forleveldetection,thesensorisgenerallymountedhorizontallyatthe

height of the requested limit level. Make sure that there are no struts

or reinforcements at this position in the vessel.

Direct the exit beam of the source container exactly towards the

measuring range of POINTRAC 31.

Fasten the sensor in such a way that it cannot fall out of the holder. If

necessary, provide the sensor with a support from below.

Mount the source container as close as possible to the vessel. If there

are gaps, secure the area with a safety fence and protective grating

so that no one can reach into the dangerous area.

You can mount the sensor (version with detector tube) with the at-

tached mounting clamp to your vessel.

Mounting clamp

17

4 Mounting

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

1

2

3

4

Fig. 6: Mounting clamp

1 Screw M8 x 80

2 Hinge bolt clamp

3 Detector tube

4 Console

1. Determine the exact mounting position of the mounting clamp

and mark the holes.

Drill appropriate holes (max. M12) for fastening the mounting

clamps.

2. For mounting, insert the detector tube (3) into the V-shape holding

xtureoftheconsole(4).

Draw the hinge bolt clamp (2) according to the illustration through

the console (4).

Screw the hinge bolt clamp (2) together and tighten the screw (1)

with a max. torque of 20 Nm (14.75 lbf/ft).

Note:

The mounting clamps do not come with fastening screws. Use fasten-

ing elements that are appropriate for the situation in your plant.

Level detection - max. detection

The POINTRAC 31 is suitable for level detection in liquids or bulk

solids. It is mounted at the height of the requested switching point.

Sensor orientation

18

4 Mounting

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

Fig. 7: POINTRAC 31 as max. level detection (uncovered)

Level detection - min. detection

Fig. 8: POINTRAC 31 as min. level detection (covered)

19

4 Mounting

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

Fig. 9: POINTRAC 31 as level detection (top view)

POINTRAC 31 lends itself well for level detection of bulk solids with

lowdensity.Mounttheinstrumenthorizontallyattheheightofthe

requested switching point.

Mount the source container VEGASOURCE displaced by 90° in order

to get the widest possible radiation angle.

When the sensor is covered by the medium, the radiation damping

is considerably stronger - hence, the switching point is all the more

reliable.

If the max. ambient temperature is exceeded, you must take suitable

measures to protect the instrument against overheating.

You can protect the instrument by providing a suitable insulation

against the heat or mounting the instrument further away from the

heat source.

Make sure these measures are taken into account already in the plan-

ning stage. If you want to carry out such measures later on, contact

our specialists to ensure that the accuracy of the application is not

impaired.

Ifthesemeasuresarenotsucienttomaintainthemax.ambient

temperature, you could consider using the water or air cooling system

weoerforPOINTRAC31.

The cooling system must also be included in the calculations for the

measuring point. Contact our specialists regarding the dimensioning

of the cooling.

Bulk solids with low

density

Protection against heat

20

5 Connecting to power supply

POINTRAC 31 • Four-wire 8/16 mA/HART

39411-EN-200522

5 Connecting to power supply

5.1 Preparing the connection

Always keep in mind the following safety instructions:

•

The electrical connection must only be carried out by trained,

qualiedpersonnelauthorisedbytheplantoperator.

•

If overvoltage surges are expected, overvoltage arresters should

be installed.

Warning:

Onlyconnectordisconnectinde-energizedstate.

In this case, the instrument is designed in protection class I. To main-

tain this protection class, it is absolutely necessary that the ground

conductor be connected to the internal ground terminal. Take note of

the national installation regulations.

Supply voltage and current signal are carried on separate connection

cables if reliable separation is required. The supply voltage range can

dierdependingontheinstrumentversion.

Thedataforpowersupplyarespeciedinchapter"Technical data".

General requirements

•

Make sure that the cable used has the required temperature resist-

anceandresafetyformax.occurringambienttemperature

•

Use cable with round cross section for instruments with housing

andcablegland.Toensurethesealeectofthecablegland(IP

protectionrating),ndoutwhichcableouterdiameterthecable

gland is suitable for.

•

Useacableglandttingthecablediameter.

•

Unusedcableglandsdonotoersucientprotectionagainst

moisture and must be replaced by blind plugs.

Voltage supply

For power supply, an approved, three-wire installation cable with PE

conductor is required.

Signal cable

The 8/16 mA current output is connected with standard two-wire

cable without shielding. If electromagnetic interference is expected

which is above the test values of EN 61326 for industrial areas,

shielded cable should be used.

Metric threads

In the case of instrument housings with metric thread, the cable

glands are screwed in at the factory. They are sealed with plastic

plugs as transport protection.

You have to remove these plugs before electrical connection.

NPT thread

In the case of instrument housings with self-sealing NPT threads, it is

not possible to have the cable entries screwed in at the factory. The

Safety instructions

Voltage supply via mains

voltage

Select connection cable

Cable glands

Page is loading ...

Vega POINTRAC 31 Operating instructions

Vega POINTRAC 31 Operating instructions

Related papers

Other documents