Electrolux WET & DRY EXTRACTION VACUUM CLEANERS Owner's Handbook Manual

Brand: Electrolux

Model: WET & DRY EXTRACTION VACUUM CLEANERS

Category: Vacuum cleaners

Type: Owner's Handbook Manual

This manual is also suitable for

Wet-Dry VAC

OWNERS HANDBOOK FOR

WET & DRY EXTRACTION VACUUM CLEANERS

Welcome to the worldwide club of vacuum cleaner owners.

Please read these operating instructions before operating your vacuum cleaner.

PRINTED ON RECYCLED PAPER

IMPORTANT USER INFORMATION

It is important that you read these instructions carefully before using

the vacuum cleaner.

These warnings are provided in the interest of your safety.

WARNING

• Always remove the mains plug from the wall socket before attempting any

form of user maintenance or cleaning specified in this booklet.

• Do not carry or drag your vacuum cleaner by the mains supply cable.

• Always ensure that the mains supply cable is not damaged in any way.

• Do not pull on the mains supply cable to remove the mains plug from the wall

socket.

• Keep the mains supply cable away from heat, oil, sharp edges and rough

surfaces.

• If the mains supply cable is damaged, it should be replaced by an authorised

Electrolux service agent or similarly qualified person in order to prevent a

hazard.

• It is dangerous to alter the specifications or modify the product.

• This appliance is not intended for use by young children or infirm persons

without supervision.

• Young children should be supervised to ensure that they do not play with the

appliance.

• Never leave the vacuum cleaner running unattended.

• If the appliance falls on its side, switch off the power immediately and stand

it upright before re-using.

• Never pick up hot ash, lighted cigarette ends or anything that is burning or

smoking.

• Do not vacuum up inflammable or combustible substances or use in areas

where they may be present.

• Do not immerse appliance in water or expose it to rain.

• Store appliance away from high heat sources.

• All filters should be replaced or cleaned at regular intervals as stated in these

operating instructions.

• Do not use this appliance for wet vacuuming without the sponge filter installed.

• Do not use the appliance for dry vacuuming without the sponge and paper

filters installed.

• Always empty waste from bucket especially after wet cleaning. (Leaving wet

or damp waste in the bucket will cause unpleasant odours and cause

bacterial growth.)

• Do not use petroleum or mineral spirits to clean the appliance. When cleaning

the suction hose, bucket or accessories, use a soft cloth and warm soapy

water only.

• Under no circumstances should you attempt to repair the appliance yourself.

Repairs undertaken by unauthorised or inexperienced persons may cause

injury and/or serious malfunctioning of the appliance.

• This appliance should be serviced by authorised Electrolux personnel and

only genuine Electrolux spare parts should be used. Failure to do so may

render the warranty void.

Fig. 1

1. Hood assembly

2. On/off switch

3. Valve

4. Cloth filter

5 Bucket

6. Castors

7. Pump switch

8. Solution filter

9. Hose intake

10.Hose

11. Curved handle

12.Suction regulator

13.Extension tubes

14.Carpet/Floor nozzle

15.Crevice nozzle

DRY USE

1415

Fig. 2

16.Foam filter

17.Hose clamp

18.Flow control unit

WET USE

19.Shampoo nozzle adaptor

20.Wet tool

21.Shampoo nozzle

21 20

Fig. 3

16.Foam filter

22.Solution tank

SHAMPOOING

using the components shown in

fig. 1.

2. For your convenience the

vacuum cleaner is supplied with

the cloth filter (4) fitted. This is

to be used for dry vacuuming.

To fit the cloth filter (4) clip it

over the top rim of the bucket

(5). Ensure it is fitted all the way

round. See fig. 6.

4. Fit the solution filter (8) to the

pin on the underside of the hood

assembly (1). See fig. 7.

5 Fit the hood assembly (1) onto

the bucket (5) and secure using

the latches. See fig. 8.

6. When the hood assembly (1) is

properly fitted the valve (3)

should line up perfectly with the

OPERATING

INSTRUCTIONS

WARNING. Always

disconnect your vacuum

cleaner from the mains

supply before maintaining

and or assembling it.

1. Before you can start using your

vacuum cleaner, you must attach

the castors (6). The castors

(6) can be found inside the

vacuum cleaner. To open the

vacuum cleaner lift the latches.

See fig. 4.

2. Remove the castors (6) and fit

them to the bucket (5) by driving

each castor (6) fully into the

holes at the bottom of the bucket

(5). See fig. 5.

HOW TO USE YOUR MACHINE

AS A DRY CLEANER

1. Assemble your vacuum cleaner

Fig. 5

Fig. 4

Fig. 7

Fig. 8

Fig. 6

hose intake (9). See fig. 9.

7. Connect the hose (10) to the

bucket (5) by fitting the threaded

end of the hose (10) into the

hose intake (9) and turn in a

clockwise direction to secure.

See fig. 10.

8. Fit the extension tubes (13) and

other accessories (whichever is

required) to the hose (10). See

fig. 1.

NOTE: The carpet/floor nozzle (14)

has two settings. Each can be

selected by using the foot-operated

switch on the left hand side of the

nozzle.

• When cleaning hard floors, the

bristles should be in the extended

position.

• When cleaning carpets the

bristles should be in the retracted

position.

9. Once all the required accessories

have been fitted together, plug

the mains lead into the wall

socket and press the on/off

switch (2) to start vacuuming.

See fig. 11.

NOTE: You can control the amount

of suction that you require by

opening and closing the suction

regulator (12) which is conveniently

placed on the curved handle (11).

See fig 12.

HOW TO USE YOUR MACHINE

AS A WET CLEANER

1. Assemble your vacuum cleaner

using the components shown in

fig. 2.

2. Fit the foam filter (16) ensuring

it completely covers the float

cage. See fig 13.

Fig. 12

Fig. 11

Fig. 10

Fig. 9

Fig. 13

3. Fit the solution filter (8) to the

pin on the underside of the hood

assembly (1). See fig.7.

4. Fit the hood assembly (1) to the

bucket (5) and secure using the

latches. See fig. 8.

5. When the hood assembly (1)

is properly fitted the valve (3)

should line up perfectly with the

hose intake (9). See fig. 9.

6. Connect the hose (10) to the

bucket (5) by fitting the threaded

end of the hose (10) into the

hose intake (9) and turn in a

clockwise direction to secure.

See fig. 10.

7. Fit the extension tubes (13) and

other accessories (whichever is

required) to the hose (10). See

fig. 2

8. If you intend using the carpet

shampoo nozzle (21), you will

have to make use of the

shampoo nozzle adaptor (19).

As the flow control unit (18) is

connected to the shampoo

nozzle adaptor (19), it will have

to be fitted to the curved handle

(11). See fig. 14.

9. The shampoo nozzle adaptor

(19) must be attached to the

extension tube (13) see fig. 3

NOTE: The wet tool (20) is fitted

with a rubber squeegee to vacuum

spills while sweeping hard floors.

Remove the rubber squeegee when

the wet tool (20) is used on carpets

or fabrics.

10.The tubing that is attached to the

shampoo nozzle adaptor (19)

and flow control unit (18), can

be secured onto the hose (10)

and extension tubes (13) with

the aid of the hose clamps (17).

When fitting the hose clamps

(17) to the extension tubes (13)

make sure that the pimple on the

hose clamp (17) is seated on

the dimple on the extension

tube (13).

11. Any excess tubing can be

wrapped around the hose (10).

Once the tubing has been

secured to the hose (10), the

metal fitting at the end of the

clear tubing can be clipped into

the valve (3) on the hood

assembly (1). See fig. 15.

12.Once all the required accessories

have been fitted together, plug

the mains lead into the wall

socket and press the on/off

switch (2) to start vacuuming.

See fig. 11.

13.For the best results, keep the

suction regulator (12) closed

Fig. 14

Fig. 15

when operating the vacuum

cleaner as a wet suction cleaner.

If the suction regulator (12) is

open water can be ejected

through it.

14.Once you have completed using

your vacuum cleaner for wet

suction, perform the operation

shown in fig. 16 with the vacuum

cleaner still switched on. This

operation should be performed

carefully alongside a drain for

about 30 seconds to ensure that

all the water is collected in the

bucket (5). You may now empty

the bucket (5) and dry it

thoroughly.

NOTE: If the foam filter (16) is dirty

wash it then dry it. The foam filter

(16) should be changed if it is

damaged. The accessories used

should also be washed and then

dried before being put away.

IMPORTANT. Automatic Shut

Off Valve. When the liquid level

in the bucket (5) exceeds the

safety level the Automatic Shut

Off Valve will operate. This will

cause loss of suction and a

slight change in noise level of

the motor. When this happens,

switch off the power and empty

the bucket (5).

HOW TO SET UP YOUR

MACHINE FOR SHAMPOOING

1. First vacuum or sweep the

surface you intend shampooing.

2. Assemble your machine using

the components shown in fig.3.

3. Fit the foam filter (16) ensuring

it completely covers the float

cage. See fig. 13.

4. Fill the solution tank (22) with

the correct ratio of shampoo and

cold water. Refer to instructions

/directions supplied with the

shampoo you intend using.

NOTE: Make sure that the shampoo

is not hazardous to the surface you

intend using it on.

5. Fit the solution tank (22) inside

the bucket (5) on the opposite

side to the hose intake (9). See

fig. 17.

6. Fit the hood assembly (1) onto

the bucket (5) ensuring that the

solution filter (8) is at the

lowest possible part of the

solution tank (22). See fig. 18.

Fig. 16

30 sec

Fig. 17

7. Secure the hood assembly (1)

with the latches as shown in fig.

9. Make sure that the valve (3)

is aligned with the hose intake

(9). See fig. 9.

8. Connect the hose (10) to the

bucket (5)

by fitting the threaded

end of the hose (10) into the

hose intake (9) and turn in a

clockwise direction to secure.

See fig. 10.

9. Fit the flow control unit (18) over

the curved handle (11). See

fig.14.

10.Fit the extension tubes (13) and

the shampoo nozzle adaptor

(19) to the hose (10). See fig.

11. Attach one hose clamp (17) to

each extension tube (13)

making sure that the pimple on

the hose clamp (17) is seated

in the dimple on the extension

tube (13). Fit the other three

hose clamps (17) to the hose

(10) spacing them evenly.

12.Now clip the clear tubing into the

hose clamps (17)

13.Insert the metal fitting on the end

of the clear tubing into the valve

(3). See. 15.

CARPET SHAMPOOING SETUP

1. Fit the shampoo nozzle (21) to

the shampoo nozzle adaptor

(19). See fig. 19.

2. Insert the shampoo connector

onto the protruding tube on

the shampoo nozzle adaptor

(19). Do this by rotating the

shampoo connector through 90°,

fitting it over the protruding tube

and then rotating it back through

90°. See fig. 20.

UPHOLSTERY SHAMPOOING

SETUP

1. Create a double loop with the

tubing between the shampoo

nozzle adaptor (19) and the

flow control unit (18). Now slide

the shampoo nozzle adaptor

(19) directly onto the curved

handle (11). See fig. 21.

Fig. 19

Fig. 18

Fig. 20

2. Fit the shampoo nozzle (21)

onto the shampoo nozzle

adaptor (19). See fig. 22.

3. Insert the shampoo connector

onto the protruding tube on the

shampoo nozzle adaptor (19).

Do this by rotating the shampoo

connector through 90°, fitting it

over the protruding tube and then

rotating it back. See fig. 20.

4. Fit the looped tubing into the

recess on the side if the

shampoo nozzle adaptor (19).

See fig. 23.

5. Your vacuum cleaner is now set

up to shampoo upholstery.

HOW TO USE THE MACHINE

FOR SHAMPOOING

1. Ensure that the suction

regulator (12) on the curved

handle (11) is closed.

2. Plug the mains lead into the wall

socket. First press the on/off

switch (2), see fig. 11, and then

the pump switch (7), see fig. 24.

3. To release the shampoo solution,

press the trigger of the flow

control unit (18) and move the

nozzle backwards. See fig. 25.

4. It is advised that the floor to be

cleaned should be cleaned in

sections, working your way to a

suitable exit. See fig.26.

Fig. 24

Fig. 26

Fig. 21

Fig. 22

Fig. 23

Fig. 25

• The solution filter (8) is

inserted correctly into the

solution tank (22). See fig. 29.

No power:

If your vacuum cleaner does not

operate, check the following:

• The plug connection.

• The electrical wall socket is

switched on.

Loss of suction:

If your vacuum cleaner loses suction

power, check the following:

• Hose (10) and other accessories

in use are not blocked.

• The filters (4 & 16) are clean.

• The bucket (5) is not overfull

and that the protective filter is not

blocked.

NOTE: The surface being

shampooed gets dried during the

release of the solution. Further drying

can take place by moving the nozzle

over the surface again without

pressing the trigger of the flow

control unit (18).

5. When you have completed using

your vacuum cleaner, it should

be disassembled in the reverse

order in which you have

assembled it.

6. To detach the metal fitting from

the valve (3), depress the valve

button and pull the metal fitting

out. See fig. 27.

IMPORTANT: Never spray the

shampoo solution in the direction

of an electrical socket or any other

electrical equipment.

GENERAL

TROUBLE SHOOTING

No shampoo release:

If pressing the trigger does not

release the shampoo solution, check

the following:

• The pump switch (7) is on.

See fig. 28.

Fig. 27

Fig. 28

Fig. 29

• The hood assembly (1) is

seated properly.

Should the above mentioned

checks not solve the problem,

please contact your nearest

Authorised Electrolux Service

Centre for advice.

HOW TO CARE FOR

YOUR MACHINE

Filter maintenance:

• Remove the cloth filter (4) and

dust it off. (DO NOT BANG IT

AGAINST THE WALL.) This

should be done on a regular

basis. When it becomes clogged

it should be washed in warm

soapy water. Ensure that the

cloth filter (4) is dry before you

refit it to the vacuum cleaner.

Storage:

Before putting your vacuum cleaner

away the following should be done:

• Empty the solution tank (22).

• Fill the solution tank (22) with

fresh water.

• Put the solution tank (22) back

into the bucket (5) and switch

the vacuum cleaner and pump

on. This is to rinse out any

shampoo still in the vacuum

cleaner, then empty any

remaining water in the solution

tank (22).

• Empty the bucket (5) of any

waste and allow it to dry

thoroughly.

• Wash and dry all the wet nozzles

(15, 20 & 21) extension tubes

(13) and hose (10) before

packing it away.

• Wash the foam filter (16) with

soapy water and allow it to dry.

IMPORTANT: Never place your

vacuum cleaner in storage before

performing the above mentioned

steps.

Other machine care:

• Never use your vacuum cleaner

without the protective filter in

place. It protects the motor. It is

seated on the underside of the

drive unit. See fig. 30.

• When the filter is dirty, it should

be washed with soapy water and

left to dry. Make sure it is

completely dry before

replacing it. If it is damaged it

should be replaced.

• Never rest the drive unit as

shown in fig. 31 because if it

falls, the latches can break.

Fig. 30

Fig. 31

curved handle (11) or the

extension tubes (13) and is

used for dry vacuuming.

Part No.: EL 044

• Upholstery nozzle

The upholstery nozzle can be

used to vacuum furniture and

other small areas.

The upholstery nozzle can be

connected to the end of the

curved handle (11) or the

extension tubes (13) and can

be used for both wet and dry

vacuuming.

Part No.: EL 045

• Small applicator

The small applicator is used

for shampooing furniture and

other small areas.

The small applicator can be

connected to the end of the

curved handle (11) by using the

shampoo nozzle adaptor (19)

in the same way as you would

for the carpet shampoo nozzle

(21). Create a double loop with

the extra tubing and fit it into the

recess on the side of the

shampoo nozzle adaptor (19)

as shown below

Part No.: EL 046

• Always rest it as illustrated OK.

See fig. 32.

• After using your vacuum cleaner

the mains lead can be wound

around the ridges on the inside

of the handle. See fig. 33.

OPTIONAL EXTRAS

AVAILABLE FROM

ELECTROLUX

The following accessories have been

specially designed to be used with

your Electrolux vacuum cleaner.

They are available from your nearest

Electrolux Service Agent.

• Dusting brush

The dusting brush can be used

to brush carpets, furniture and

curtains while vacuuming.

The dusting brush can be

connected to the end of the

Fig. 32

Fig. 33

Cartridge Filter

Part No.: EL 048

Reusable dust bag

Part No.: EL 049

Should you require any further assistance,

please contact our TOLL FREE customer

help line on 0800 222 825

• Cartridge filter and reusable

dust bag

The cartridge filter and reusable

dust bag can be used instead of

the cloth filter.

Slide the cartridge filter over the

bottom of the motor housing until

it rests on the shoulder. Pull the

reusable dust bag over the

cartridge filter ensuring that it

clips completely over the rim of

the cartridge filter as shown

below.

WARRANTY

Electrolux South Africa (Pty) Ltd., (’Electrolux’) warrants to the original

purchaser (’the Purchaser’) that the appliance identified on this booklet

is free from defects in the material or workmanship under normal use

and service subject to the following conditions:

1. This warranty, remains valid for a period of one year in respect of appliances used for domestic purposes only. Any Electrolux domestic

appliance used in a commercial capacity will not be covered by the warranty.

2. The Purchaser shall refer the appliance for repair to any Electrolux branch or Electrolux authorized service agent and nowhere else. On

referral for repair in accordance with the warranty as aforesaid Electrolux shall, at its opinion, if satisfied that the condition herein set out

have been complied with, replace or repair the appliance without cost to the Purchaser.

3. The Purchaser shall use only genuine Electrolux accessories. Without limiting the generality of the aforegoing such accessories shall include

dust bags, filters and drivebelts.

4. This warranty does not apply to light bulbs, external electrical connections,flex, and all other items where the length of life depends upon

the use and care given. Without limiting the generality of the aforegoing such items shall include belts, filters, bristled brushes and bags

fitted to polishers and vacuum cleaners.

5. This warranty shall only apply to appliances purchased in and retained for use in South Africa, Namibia, Lesotho, Botswana and Swaziland.

6. The Purchaser shall not remove the serial number of the appliance.

7. Electrolux undertakes that all goods supplied by it shall conform to the specifications of the same except insofar as these are necessarily

modified by Electrolux from time to time. Electrolux does not warrant or give any representation of any nature in respect of any appliances

supplied by it or the materials from which those appliances were made, or the workmanship in the making of those appliances or the fitness

of those appliances for any particular purpose whether or not that purpose is known to Electrolux.

8. Electrolux shall not be responsible for any loss or damage of any nature whatsoever whether direct or indirect, consequential or otherwise,

sustained as a result of any appliance being defective or not conforming to the description thereof, or as a result of improper use of the

appliance (which, without limiting the generality thereof, shall include the use of incorrect voltage or faults in the house wiring, improper

use of the controls and failure to use the appliance in accordance with the operating instructions), or as a result of any other cause

whatsoever.

9. Abuse of the appliance by the purchaser will render this warranty invalid. Improper use of the appliance and failure to use the appliance

or maintain the appliance in accordance with the relevant instructions will be considered as abuse.

10. The purchaser shall, when referring the appliance for warranty repair as aforesaid, produce the cash slip, hire purchase documents or

invoice together with the instruction leaflet in which this warranty is contained.

11. Electrolux shall be entitled to charge the Purchaser for services rendered outside the warranty period or for any quotations given when no

fault is found, for any replacement parts supplied and which are not covered by the warranty.

12. The above conditions constitute separate and devisable resolutive conditions and failure of the Purchaser to observe each or any of the

said conditions will render this warranty of no force and effect.

13. No understandings or representations, which are not in writing and accepted by Electrolux or specified in writing, are binding on it.

14. All implied warranties in respect of the appliance are expressly excluded.

ELECTROLUX FLOORCARE

A DIVISION OF ELECTROLUX S.A. (PTY) LTD

Reg. no. 1971/005541/07

Electrolux reserves the right to make improvements or modifications to the product from time to time and consequently the details given in this book are subject to

alteration without notice.

CUSTOMER HELPLINE

0800 222 825

(Toll Free South Africa wide)

IMPORTANT!

For future reference we suggest you record the following details here, and keep the receipt with the handbook as proof of purchase.

PURCHASED FROM: ..........................................................................................................................................................................................................................

DATE PURCHASED: .....................................................................................................MODEL NO:..................................................................................................

SERIAL NO.

PART No: 14066-002