Vivo STAND-SIT2DD Assembly Instructions

Brand: Vivo

Model: STAND-SIT2DD

Category: Flat panel desk mounts

Type: Assembly Instructions

Sit to Stand Dual Monitor Desk Mount Workstation

with USB

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-sit2dd

SKU: STAND-SIT2DD

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

A (x1)

Base

B (x1)

Adjustable Arm

C (x1)

Smartphone Tray

O (x1)

4mm Allen

Wrench

P (x1)

6mm Allen

Wrench

N (x1)

3mm Allen

Wrench

J (x1)

Clamp Plate

K (x1)

Clamp

L (x2)

VESA Plate

M (x1)

Cable Clip

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED

D (x1)

Keyboard Tray

E (x1)

Lower Support

Arm

F (x1)

Arm

G (x1)

Upper

Support Arm

H (x1)

Rear Cover

I (x1)

Clamp Brace

R (x2)

Carriage Bolt

Q (x1)

Grommet Base

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

M-A (x8)

M4x12

M-C (x8)

D5 Washer

M-B (x8)

M5x12

T (x2)

M8x25

S (x2)

Support

Plate

U (x6)

ST4.8x16

W (x2)

M5x10

V (x4)

M6x12

Y (x2)

Spring Washer

X (x2)

Nut

Z (x1)

Wrench

ASSEMBLY STEPS

STEP 1

TOOLS NEEDED

Phillips

Screwdriver

OPTION A: Clamp Installation

Attach clamp brace (I) to base (A) using M6x12 bolts (V), and tighten with 4mm Allen wrench (O).

Place clamp plate (J) on top of clamp (K). Install clamp (J) to upper holes of clamp brace (I) for a desk

thickness of 3/8” to 1-1/2” (10 - 40mm), or to lower holes for a desk thickness of 1-1/2” to 3-1/4” (40 -

84mm), and tighten with Allen wrench (P). Place assembled base on edge of desk and tighten clamp

bolts evenly with 6mm Allen wrench (P).

OPTION B: Grommet Installation

Place carriage bolts (R) into square holes in grommet base plate (Q). Attach grommet base plate to

base (A) using M6x12 bolts (V), and tighten with 4mm Allen wrench (O). Place assembled base over

cable grommet hole in desktop, and tighten using support plates (S), lock washers (Y) and M8 nuts (X),

and tighten with crescent wrench (Z). If a grommet hole isn’t present, drill a 3/8” (10mm) hole through

the desktop for each bolt.

10-40m m

40-84m m

0 - 13.2 lbs

(0 - 6 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

2.2 lbs

(1 kg)

KEYBOARD

STEP 2

Carefully extend the adjustable arm (B) to the

raised position as shown. Insert the adjustable

arm into the socket of the base, then secure

using the 3mm Allen wrench (N).

STEP 3

Remove the knob from the lower support arm (E) to separate into lower support arm (E1) and knob

(E2).

STEP 4

Assemble smartphone tray (C) to lower support arm

using M5x10 screws (W) with a Phillips screwdriver.

STEP 5

Assemble keyboard tray (D) to lower support arm

using ST4.8x16 screws (U) with a Phillips screwdriver.

STEP 6

Mount upper support arm (G) to lower support arm

using M8x25 bolts (T) and tighten with 6mm Allen

wrench (P).

Adjust keyboard tray tilt using the 4mm Allen wrench (O). Turn the adjustment screw clockwise to tilt

up to position 1a, and counter-clockwise to tilt down to position 1b. Install the knob (E2) to lock the

position.

STEP 8

STEP 7

Place the support arm/tray assembly onto the

upper post of the adjustable arm, then secure using

the wrench (N).

STEP 9

STEP 10

Install the VESA plate (L) to monitor using M4x12 bolts (M-A) or M5x12 bolts (M-B) with washers (M-C),

making sure the rounded edges of the rear bracket are facing up.

STEP 11

Place the monitors with VESA plates into the supports on the arm, then turn the screw on each support

to secure the monitors. Tighten with a Phillips screwdriver.

Remove the knob from arm (F). Slide the arm onto the upper support arm, then reinstall the knob.

Tighten the bolts with the 4mm Allen wrench (O) to secure height.

Adjust as Desired

STEP 12

STEP 13

Organize cables and reinstall cable covers to

base and adjustable arm.

STEP 14

Install rear cover (H) to clamp brace if the clamp

option was used. Install cable clip (M) to back

of upper support arm and remove cable covers

from base and adjustable arm.

Loosen knob in back to adjust monitor

height. To adjust gas spring support,

turn the hex screw on top of the rear joint

using the 6mm Allen wrench (P). Counter-

clockwise will increase support, and

clockwise will decrease support.

LAST UPDATED: 05/13/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo STAND-SIT2DD Assembly Instructions

Brand: Vivo

Model: STAND-SIT2DD

Category: Flat panel desk mounts

Type: Assembly Instructions

Download PDF

report

Vivo STAND-SIT2DD Assembly Instructions

Vivo STAND-SIT2DD Assembly Instructions

Related papers

Other documents