Reely 1600322 Operating instructions

Brand: Reely

Model: 1600322

Type: Operating instructions

Page is loading ...

• Avoidblockingthedrive.Thearisingcurrentscouldpermanentlydamagethemotorand/or

speedcontroller.

• Ensureasmooth-running,regularlyserviceddriveline.

• Checkthe vehicleand the speed controller/motor forsigns ofdamage. If you notice any

damage,discontinueoperationofthevehicleand/orthespeedcontroller/motor.

• Beforerechargingthebattery,itmustbedisconnectedfromthespeedcontroller.

• Handletheproductwithcare.Impacts or falls (even froma low height)may damagethe

product.

• Donotleavepackagingmaterialunattended,asitmaybecomeadangeroustoyforchildren.

• Consultatechnicianifyouarenotsurehowtouseorconnecttheproduct,orifyouhave

concernsaboutsafety.

• Maintenance,modicationsandrepairsmustbecarriedoutbyatechnicianoraspecialist

repaircentre.

• Ifyouhavequestionswhichremainunansweredbytheseoperatinginstructions,contactour

technicalsupportserviceorothertechnicalpersonnel.

Assembly

• Iftheproductistobeusedasareplacementforanexistingcontrolunit/motor,thenrstremovetheold

componentsfromyourmodel.

• Installapiniongearonthedriveshaftofthebrushlessmotorthatissuitableforthepiniongeardriveand

shaftdiameter.Thepiniongearisgenerallyafxedwithagrubscrew.

Attention!

 Ensurethatthegrubscrewsitsexactlyontheattenedsideofthe

driveshaftandisscrewedtight inthatposition(seetheschematic

diagramon the right, without thegear wheel) otherwisethe pinion

gearwillquicklyloosen.

 Theexactpositionofthepiniongearonthedriveshaftmustbedeterminedafterthemotoris

mounted.Thus,onlytightenthepiniongearlightlyinitially.

• Mountthemotorinyourvehicleandscrewitintoplace.Useonlysuitablescrewsthatdonotprotrudetoo

farintothemotor.Afterinstallation,alwaysensurethattherotorinthemotorcanbeturnedeasilyandthat

nogrindingsoundcanbeheard.Ifthisruleisnotobserved,themotormaybedamaged,inwhichcase

thewarranty/guaranteewillbevoid.

 Thedistancebetweenthepiniongearandthepiniongeardrivewillbesetlater,itisnotimportant

atthisstage.

• Nowcheckthatthepiniongearcomesintoexactcontactwiththepiniongeardriveand

isnotskewedtotheside.

Attention!

 Theexactpositionofthepiniongeartothepiniongeardriveisveryimportant,

itmustnotbeskewedtothesideasthiswilldamagethepiniongeardrive(the

transferofpowerwillonlyoccuroverasmallarea).

• Adjusttheinstallationpositionofthepiniongearonthedriveshaft,removingthemotor,

ifnecessary.

 Onlywhenthepiniongearsitsexactlyparalleltothepiniongeardriveshouldthegrubscrew

inthepiniongearbetightenedrmly.Thefasteningscrewofthemotorpiniongearmustbe

securedagainstlooseningwithadropofthreadlocker.

• Aftercorrectinstallationofthepiniongearonthedriveshaftofthemotor,thecorrectdistancebetweenthe

piniongearandthepiniongeardrivemustbeset.

Generally,whendealingwithmotormounts,onemountholewillberoundandtheotherwillbeoblong.

Themotoristhusattachedwiththescrewintheroundholeandcanbeadjustedwiththeoblonghole.

• Loosenbothscrewsalittle,sothatthemotorcanbeturnedwithasmallamountofforce.

 Thedistancebetweenthepiniongearandthepiniongeardrivemustnotbetoosmallortoo

large,asthismaydamagethepiniongeardrive.

 Thedistanceissetcorrectlyiftheedgesofthegearwheelinterlockwellandthedrivecanbe

turnedwithoutgreateffort.Afterthersttripswiththevehicle,checkthemountingofthemotor

andthepositionofthemotorpiniongeartothemaingearwheel.

 Incorrectsettingsareindicatedbyincreasedwearofthemotorpiniongear/maingearwheel.

• Screwthemotordownwhenitisinthecorrectposition.

• Nowmountthespeedcontrollerinthevehiclechassis.Choosealocationwhichisasfaraspossiblefrom

thereceiver.Thespeedcontrollershouldalsonotbedirectlynexttothemotor.Ensurethatthein-builtred

andgreenLEDsbelowthethreemotorconnectioncablesarestillvisiblewheninstalled.

• Connectthecablesofthespeedcontrollertothemotorcables,noteanyexistingcolourcodingasthiswill

ensurethattheforwards/reversemovementofthemotorinconjunctionwiththespeedcontrolleriscorrect.

 Ifthedirectionofrotationofthemotorislaterincorrect(dependingonthevehicle'stransmis-

sion),simplyswaptwoofthethreeconnections.Themotorthenrotatesintheotherdirection.

• Velcrooradouble-sidedadhesivetapemaybeusedtoattachthespeedcontroller.

• Checkthefanfasteningscrewsforrmseating(checkthisregularlyafteroperatingthevehicle).

Important!

 Thespeedcontrollerincludedinthekitisdesignedforoperationwitha3-4-cellLiPorecharge-

ablebattery(ratedvoltage11.1-14.8V)oran8-12-cellNiMHrechargeablebattery(rated

voltage9.6-14.4V).

 Connectingabatterywithmorecellstothespeedcontrollerwilldamagethespeedcontroller

and/ormotor.Thiswillvoidthewarranty/guarantee.

 Ifconnectingamotortothespeedcontrollerthatissuitableformorecells,alwaysobservethe

thresholdvaluesofthespeedcontroller,seechapter"TechnicalData”.

• Theon/offbuttonwithprogrammingbuttonmustbeattachedsothatitcanbeeasilyoperated.Thisalso

requiresattachmentwithvelcroordouble-sidedtapeorsimilar.

• Positionallcablessothattheycannotbecomeentangledinrotatingormovingpartsofthevehicle.Use

cabletiestoafxthem,forexample.

Operating instructions

Model car brushless drive set 1:8, 2200 kV

Item no. 1600322

Intended use

Theproductconsistsofanelectronicspeedcontrollerandabrushlessmotor.Themotorandspeedcontroller

arewater-protectedandareusedforinstallationintouringcars,buggies,trucksandmonstertrucks.The

speedcontrollerisdesignedfortheconnectionoftworechargeablebatteries(connectionofasinglebattery

isonlypossiblewithajumperplug,notincluded).

ThespeedcontrollerisprogrammedwiththeprogrammingbuttonandtwoLEDs.

Forsafetyandapprovalpurposes,youmustnotrebuildand/ormodifythisproduct.Usingtheproductfor

purposesotherthanthosedescribedabovemaydamagetheproduct.Inaddition,improperusecancause

hazardssuchasashortcircuitorre.Readtheinstructionscarefullyandstoretheminasafeplace.Only

makethisproductavailabletothirdpartiestogetherwithitsoperatinginstructions.

ThisproductcomplieswithstatutorynationalandEuropeanregulations.Allcompanyandproductnamesare

trademarksoftheirrespectiveowners.Allrightsreserved.

Package contents

• Speedcontroller

• Motor

• Operatinginstructions

Up-to-date operating instructions

Todownloadthelatestoperatinginstructions,visitwww.conrad.com/downloadsorscantheQRcodeonthis

page.Followtheinstructionsonthewebsite.

Explanation of symbols

 Thesymbolwithanexclamationmarkinatriangleisusedtohighlightimportantinformationin

theseoperatinginstructions.Alwaysreadthisinformationcarefully.

 Thearrowsymbolindicatesspecialinformationandadviceonhowtousetheproduct.

Safety information

Read the operating instructions and safety information carefully. If you do not follow the

safety information and information on proper handling in these operating instruction,

we will assume no liability for any resulting personal injury or damage to property. Such

cases will invalidate the warranty/guarantee.

• Theunauthorisedconversionand/ormodicationoftheproductisprohibitedforsafetyand

approval reasons. Never disassemble the product; there are no components inside the

housingthatyouneedtosetorservice.Doingsowillinvalidatethewarranty/guarantee.

• Thisproductisnotatoyandmustbekeptoutofthereachofchildren.

• Thespeedcontrollerandmotorarewater-protected.Largequantitiesofwaterastheresult

oflonger"underwaterjourneys",however,maypermanentlydamagethefan.Forthisreason,

thefan must bedismantled before"wet trips". Oncethese trips arecomplete, the speed

controllermustbecleanedthoroughlyandthefanreassembled.

• Alwaysdisconnectthebatteryfromthespeedcontrollerifthespeedcontrollerisnotneeded.

Ifthespeedcontrollerisnotusedforshortperiods,itcanbedeactivatedwiththeon/offswitch.

• Alwaysswitchthetransmitteronrstbeforeconnectingthespeedcontrollertothebattery

andswitchingiton.

Before switching the transmitter off, switch the speed controller off and, if necessary,

disconnectitfromthebattery.

• The speed controller can be used in conjunction with the motor supplied for NiMH/NiCd

rechargeablebatteriesaswellasLiPorechargeablebatteries.Thepermittednumberofcells,

etc.canbefoundinthetableinchapter"Technicaldata".

• Operatethespeedcontrolleronlywitharechargeablebatterypackandneverwithapower

adaptor.

• Depending on the intendeduse (on- or off-road) and road surface (tarmac, sand, grass)

used,theremaybedifferentcurrentvaluesinoperation.Pleasenotethetechnicaldatain

theseoperatinginstructions.Ifthethresholdvaluesarenotobserved,themotorand/orspeed

controllermaybepermanentlydamaged.Thiswillvoidthewarranty/guarantee.

• Themotor,speedcontrollerandbatterycanbecomeveryhotduringoperation.Riskofburns!

• Whenhandlingvehicles,ensurethatnoobjectsorbodypartsareintherotatingparts.Risk

ofinjury!

• Onlyconnectonesinglebrushlessmotortothespeedcontroller.

• Thebrushlessspeedcontrollerisnotsuitablefortheoperationofconventionalelectricmotors

withtwoconnections.

• Maintainthelargestpossibledistance betweenthereceiverand speedcontroller/motorto

avoidinterference.

• Donotinstalltheantennacableofthereceiverparalleltolivecables.

• Donotbundletheantennacableofyourreceiversystem,insteaduseanantennatube,for

example,whichprotrudesverticallyfromthevehicle.

• Alwaysswitchthetransmitteronrstandmoveitsoperatingleverformotorcontrolintothe

neutralposition(motoroff).Onlythencanyouconnectthespeedcontrollertoabatterypack

andswitchiton.Whenswitchingoff,proceedinreverseorder;rstswitchthespeedcontroller

offanddisconnectitfromthebattery,thenswitchthetransmitteroff.

• Duringoperationofthemodel,sufcientcoolingmustbeprovidedforthespeedcontrollerand

themotor.Nevercovertheheatsinkorthefanonthespeedcontroller.

• Alwayscheckthefunctionalityofthefanbeforeoperation,donotblockthefan;removedust

ordirtfromthefanthathasaccumulatedduringoperationofthevehicle.

Connection of one or two drive batteries

Dependingonthemanufacturerandtype,modelvehiclesin1:8scalehaveoneortwobatteryholders(e.g.

twobatteryholdersareusedsothatanoptimumcentreofgravitycanbeachieved).

Thespeedcontroller,therefore,hastwoT-connectorsforconnectionoftwoidenticaldrivebatteries(e.g.two

2-cellLiPodrivebatteries).

Ifusingasingledrivebattery(e.g.3-cellLiPodrivebattery),ajumperplug(notincluded)mustbeusedon

oneofthetwoT-connectorsonthespeedcontroller.ThesecondT-connectoronthespeedcontrolleristhen

usedforconnectiontothedrivebattery.

 WerecommendthatthejumperplugbeusedontheT-connectorwiththetworedcables.The

otherT-connectoronthespeedcontrollerthenhasthecorrectcolourmarkingforpositive/+(red)

andnegative/-(black).

Making a jumper plug

Produceajumperplugasshownintheguretotheright.

Ensurethatthesolderedjoints(e.g.withheatshrinktubing)arewellinsulated.Thematerial

requiredforthisisnotincludedandmustbepurchasedseparately.

Fixthecableofthespeedcontrollerinthevehicleinsuchawaythatitcannotgetintorotat-

ingparts(drive)(e.g.useacabletie).

Programming

a) Programming the full throttle and neutral position

Toprogramthefullthrottlepositionforforwards/reverseandtheneutralposition,proceedasfollows:

• Switchthetransmitteronandleavethethrottle/brakeleverintheneutralposition.Setthetrimmingfor

thetravelfunctioninthecentreposition.Forcomputertransmitters,notravellimitorABSmaybepro-

grammed.Ifprogrammingfailstofunctionasdesired,thecontroldirectionforthethrottlelevermustbe

settoreverse.

• Switchthespeedcontrolleroffandconnectoneortwodrivebatteries.

 Ifusingasingledrivebattery,ajumperplug(notincluded,seeabove)mustbeusedononeof

thetwoT-connectorsonthespeedcontroller.

 WerecommendthatthejumperplugbeusedontheT-connectorwiththetworedcables.The

otherT-connectorthenhasthecorrectcolourmarkingforpositive/+(red)andnegative/-(black).

• Holddownthesetupbuttonandswitchthespeed controlleron.Re-

leasethesetupbuttonassoonastheLED(seegureright)onthe

speedcontrollerashesredandthemotoremitsanaudiblesignal.

 The audible signal is generated by brief activation of the

brushlessmotor.Dependingonthemotor,thissoundmaybe

veryquietorinaudible.Inthiscase,observetheLEDsonthe

speedcontroller.

• Now,press theprogrammingbuttononcewhilethethrottle/brake le-

verisintheneutralposition.TheLEDonthespeedcontrollerbriey

ashesgreen.Themotoremitsanaudiblesignal.

• Movethethrottle/brakelevertothefullforwardsthrottleposition(moveittowardsthehandle)andholditin

place.Now,presstheprogrammingbuttononce.TheLEDashesgreentwice.Themotoremitsanaudible

signal.Thefullforwardsthrottlepositionissaved.

• Movethethrottle/brakelevertothefullreversethrottleposition(moveitfullyawayfromthehandle)and

holditinplace.Now,presstheprogrammingbuttononce.TheLEDashesgreenthreetimes.Themotor

emitsanaudiblesignal.Thefullreversethrottlepositionissaved.

• Releasethegas/brakeleversothatitisintheneutralposition.TheLEDashesgreenthreetimes.The

motoremitsanaudiblesignal.Theneutralpositionprogramminghasbeensaved.Themotorandspeed

controllerarereadyforoperationafterapprox.threeseconds.Whenyounowswitchthespeedcontroller

onagain,thespeedcontrollerisreadyforoperationwiththesettingsimplementedabove.

b) Programming additional features

 Allpossiblespeedcontrollersettingscanbeprogrammedwitheasewithanoptionalprogram-

mingcard.Theprogrammingcardisconnectedtothefanconnection(removetheconnection

plugfromthefanbeforehand).Tothisend,seethenotesatwww.conrad.comfortheproduct.

• Connectthespeedcontrollertothedrivebattery,presstheprogrammingbutton(pressandhold)and

switchthespeedcontrolleron.TheredLEDashes.

PressandholdtheprogrammingbuttonuntilthegreenLEDashes.

Youarenowatprogramminglevelandcanprogramthefollowingmenuitems.

 The5menuitemsaredisplayedinanendlessloopwhiletheprogrammingbuttonishelddown.

 1xashismenuitem1,2xashismenuitem2,etc.uptomenuitem5.Theloopthenstarts

againwithmenuitem1.

 Oncethedesiredmenuitem(1,2,3,4or5)hasbeenreached,releasetheprogrammingbutton.

Youarenowinthesubmenufortheselectedmenuitem.

 TheredLEDnowindicatesthecurrentsettingfortheselectedmenuitem.

• Toselectthedesiredsettinginthesubmenu(fordescription,seec),simplypresstheprogrammingbutton

untiltheredLEDandtheaudiblesignalindicatethedesiredsetting.

Main menu Sub menu

Setting GreenLEDashes+audiblesignal RedLEDashes+audiblesignal

1 1xshort 1xshort

2 2xshort 2xshort

3 3xshort 3xshort

4 4xshort 4xshort

5 1xlong 1xlong

6 1xlong+1xshort

7 1xlong+2xshort

8 1xlong+3xshort

9 1xlong+4xshort

• Onceyouhaveselectedandprogrammedthedesiredsetting,switchthespeedcontrolleroff.Thesetting

isthensaved.Ifyouwouldliketocarryoutprogrammingofanothermenuitem,theprogrammingprocess

mustberestarted.

c) Available programming options

Menu item 1 = driving mode

Here,youcandeterminethedrivingmode(drivingmode1=forwardswithbrakeonly;2=forwardsand

reversewithbrake;3=forwardsandreverse).

Whenswitchingfromforwardstobrakeindrivingmode1,thereisnoswitchovertoreverse,thevehicle

isbrakedonly.Indrivingmode2,thereisnoimmediateswitchovertoreverse,insteadthereisaninterim

pause(1xneutralpositiononthetransmitter).Bothdrivemodesarepreferredas,unlikedrivingmode3,they

protectthegearunit,wheelsandbatterycapacity.

Menu item 2 = motor brake

Whenthethrottleleveronthetransmitterismovedtotheneutralpositionfromtheforwardsposition,the

motorbrakeisactivated.

Thefunctioncorrespondstotheenginebrakeina"real"car,whenyoutakeyourfootofftheacceleratorpedal

butdonotdepressthebrakepedal.

Themotorbrakecanbeprogrammedovereightlevels.Thehigherthesetvalue,thestrongerthebrake

effect.Thefollowingvaluescanbeset:

1=0%;2=5%;3=10%;4=20%;5=40%;6=60%;7=80%,8=100%

Menu item 3 = low voltage detection

LowvoltagedetectionisforoperationofmodelswithLiPoandNiMHrechargeablebatteries.Activationofthis

functionisrecommendedespeciallyforLiPobatteriestoavoidharmfuldeepdischarge.

WithaLiPobattery,thesettingvaluesrefertoavoltagevalueperbatterycell.

Example:withasettingof3.0V,a2-cellbatteryatabatteryvoltageof6.0V(2cellsx3.0V=6.0V)would

reachthesetlowvoltagethreshold.Thespeedcontrollerwouldthenswitchthemotoroffinordertoprevent

deepdischargeofthebattery.

IfaNiMHbatteryisused,thecalculationofthenumberof(LiPo)cellsisbasedonthebatteryvoltagethat

thespeedcontrollermeasuresatswitch-on.Ifavoltageof9.0to12.0Visdetectedafterswitchingthespeed

controlleron,theswitch-offisthesameasfora3-cellLiPobattery.Ifavoltageoflessthan9.0Visdetected,

thespeedcontrolleractivatestheswitch-offasfora2-cellLiPobattery.

Example:ifyouhaveconnectedafullycharged8-cellNiMHbatterywithapprox.11.2Vbatteryvoltageandif

thecut-offvoltageper(LiPo)cellissetto2.6V,thelowvoltagedetectionswitchesthemotoroffatabattery

voltageof7.8V(3x2.6V=7.8V).

Thefollowingsettingsarepossible:

1=nolowvoltageprotection;2=2.6V/cell;3=2.8V/cell;4=3.0V/cell;5=3.2V/cell,6=3.4V/cell

 ForLiPobatteries,werecommendasettingof3.2V/cell.

 Thebatteryvoltageischeckedcontinuously.If a low voltage is detectedfor morethan two

seconds,themotorisswitchedoff.TheredLEDonthespeedcontrollerthenashestoindicate

switch-offduetolowvoltage.Inthatcase,discontinueoperationandchargethebatteryfully.

Menu item 4 = start-up dynamics

Withthissetting,youcanadjustthestart-updynamicsoverninelevels(1-9):1=gentle;5=medium;9=

veryhigh.

Thehigherthesetvalue,themoreaggressivelythemotorreactstothecontrolcommandsonthetransmit-

ter.Itisimportantthatthebatterycandeliverthecurrentrequiredforthispurpose(LiPobatterywithhighC

rate).Ifthemotor"stutters"atthehigheststart-updynamicslevelandthebatteryisnotempty(orispowerful

enough),thetransmissionratiomayneedtobeadjusted.

Menu item 5 = brake effect

Here,youcansetthebrakeeffectthatisappliedwhenyoumovethecontrolleveronthetransmitterfrom

forwardstoreverse(orbrake)toitsendpoint.

Thefollowingvaluescanbeset:1=25%,2=50%,3=75%;4=100%;5=brakeoff.

 Thehigherthesetvalue,thehigherthebrakingeffect.Thehigherthebrakingeffect,thehigher

theloadonthegearunitandtyres.

d) Restoring default settings

Withthespeedcontrollerswitchedon,pressandholdtheprogrammingbuttonforapprox.threeseconds

untiltheredandgreenLEDashsimultaneously.TheredLEDthenashesonitsowntoindicatesthatthe

defaultsettingshavebeenrestored.

Withthisresettodefaultsettings,allprevioussettings,includingprogrammingoftheneutralposition,are

reset.

Thespeedcontrollermustthenbefullyreprogrammedbystartingwithprogrammingoftheneutralposition.

Todothis,switchthespeedcontrolleroffandstartthereprogramming(see"Programmingoffullthrottle

andneutralposition").

Connection to the receiver

Connectthe three-pole plug of the speed controller to the corresponding channel of the receiver.Make

absolutelysureyouhavethecorrectreceiverconguration(seeoperatinginstructionsforreceiveraswell

astheinscriptiononthereceiver).

Yellow/white/orangecable:Controlsignal

Redcable:Operatingvoltage

Brown/blackcable:GND/negative

 ThespeedcontrollerhasaBEC.Thissuppliesthereceiverdirectlyfromthedrivebatteryvia

thespeedcontroller.IftheBECisusedasapowersupplyforthereceiver,noreceiverbattery,

rechargeableordisposable,maybeused.

Important!

 If,insteadofthespeedcontroller'sBEC,aseparatereceiverpowersupplyisusedforthereceiv-

er,themiddleredwireonthespeedcontroller'sthree-pinreceiverplugmustbedisconnected.

Failuretocomplywiththisinstructionwillpermanentlydamagethespeedcontroller!Thiswill

voidthewarranty/guarantee.

Information on operation

Important!

 Thespeedcontrollerincludedinthekitisdesignedforoperationwitha3-4-cellLiPorecharge-

ablebattery(ratedvoltage11.1-14.8V)oran8-12-cellNiMHrechargeablebattery(rated

voltage9.6-14.4V).

 Connectingabatterywithmorecellstothespeedcontrollerwilldamagethespeedcontroller

and/ormotor.Thiswillvoidthewarranty/guarantee.

 Ifconnectingamotortothespeedcontrollerthatissuitableformorecells,alwaysobservethe

thresholdvaluesofthespeedcontroller,seechapter"TechnicalData”.

• Whenthespeedcontrollerisswitchedon,thegreenLEDashesaccordingtothenumberofcellsin

theconnectedLiPobattery(e.g.3-cellLiPo-battery=ash3x).Anaudiblesignalsoundswiththesame

numberofsignalsasLEDashes.WhenallLEDshavegoneout,thespeedcontrollerisreadytouse.

• Ifthespeedcontrollerrecognisesanabnormalvoltagevalue,thespeedcontrolleremitsacorresponding

warningsignal(2tones,1secondpause,2tones,1secondpause,etc.).

Inthiscase,checkthebattery(voltage,chargestatus)andtheconnectionsbetweenthebatteryandthe

speedcontroller.

Ifthespeedcontrollerrecognisesafaultycontrolsignalfromthereceiverafterbeingswitchedon,thered

LEDonthespeedcontrollerashesquickly.

• Checkthetrimmingforthethrottleleverorreleasethethrottleleverintothecentreposition(neutralposi-

tion)whenthespeedcontrollerisswitchedon.

• TheredLEDlightsupinforwardsandreverseorwiththecorrespondingcontrolsignalfromthetransmitter.

Whendrivingforwardsat100%fullthrottle,thegreenLEDalsolightsup.

Ifabrakingeffectof100%issetundermenuitem5,thegreenLEDlightsupbrieywhenusingthebrake

orwhenreversing.

• Whenchangingbetweenforwardsandreverse(intravelmode2),thethrottlelevermustbeplacedbriey

intotheneutralposition(approx.2seconds).Ifthethrottleleverisshifteddirectlyfromforwardstoreverse,

thespeedcontroller'sbrakeisactivated(thevehiclewillNOTgobackwards!)

• Ifthedrivefunctionorbrakefunctionrespondoppositetothemovementofthethrottleleveronthetrans-

mitter,activatethereversefunctiononthetransmitterorswapanytwoofthethreemotorcables.

• Thefunctionalityofthefanmustbecheckedbeforeandaftereachtrip.Thisisespeciallytrueifthevehicle

hascomeintocontactwithwater.Intheeventofdoubt,thefanmustbedismantledandcleaned.

• Forsafetyreasons,thespeedcontrollerswitchesthemotoroffintheeventofanexcesstemperature

onthespeedcontroller(i.e.over+105°C).Inthiscase,thegreenLEDonthespeedcontrollerashes.

Discontinueoperationimmediatelyandcheckthetransmissionofthedriveandthefunctionalityofthefan

onthespeedcontroller.

• Ifthespeedcontrollerrecognisesthatthereisnosignalforspeedcontrolformorethan0.2secondsin

operation,themotorisswitchedoff.Inthiscase,checkthepositionofthereceivingantenna,theconnec-

tionbetweenthespeedcontrollerandthereceiverandthebatteriesinthetransmitter.

Ending operation

First,switchthespeedcontrolleroff(movetheswitchintothe"OFF"position).Then,disconnectthedrive

battery(orbothdrivebatteries)fromthespeedcontroller.Onlynowdoyouswitchthetransmitteroff.

Disposal

 Electronicdevicesarerecyclablewasteandmustnotbeplacedinhouseholdwaste.Always

disposeoftheproductaccordingtotherelevantstatutoryregulations.

Technical data

Important!

 Thespeedcontrollerincludedinthekitisdesignedforoperationwitha3-4-cellLiPorecharge-

ablebattery(ratedvoltage11.1-14.8V)oran8-12-cellNiMHrechargeablebattery(rated

voltage9.6-14.4V).

a) Speed controller

NumberofcellsNiMH 8-12(9-16.8V)

NumberofcellsLiPo 3-4(9-16.8V)

Lowvoltagedetectionfor

LiPobattery

2.6V/2.8V/3.0V/3.2V/3.4Vpercell/canbedeactivated

Continuouscurrent(max.5min) 100A

Current(max.1sec) 650A

SBEC(synchronised) 6V/DC,5A

Fan 6V/DC

Excesstemperatureswitch-off Yes(at+105°C)

Max.kVofthemotor(on-road,3S) <=4000

Max.kVofthemotor(on-road,4S) <=3000

Max.kVofthemotor(off-road,3S) <=3000

Max.kVofthemotor(off-road,4S) <=2400

Suitablemotorsize 4068or4074

Connectorsystemformotor 4mmgoldcontact

Connectorsystemforreceiver JR

Dimensions(LxWxH) 59.5x48x42mm

Weightwithcableapprox. 173g

b) Motor

NumberofcellsNiMH 8-18

NumberofcellsLiPo 3-6

Current(continuous) max.80A

Power(continuous) max.1700W

Current(temporary<10s) max.120A

Power(temporary<10s) max.2600W

Continuouscurrentat3S 80A(888W)

Continuouscurrentat4S 80A(1184W)

Continuouscurrentat5S 80A(1480W)

Continuouscurrentat6S 76A(1687W)

Revolutionspervolt(kV) 2200

Numberofpins 4

Numberofturns 2

Connectorsystem 4mmgoldcontact

Shaftdiameter 5mm

Usefulwavelength Approx.18mm

Dimensions(ØxL) 40x74mm

Weightwithcableapprox. 384g

ThisisapublicationbyConradElectronicSE,Klaus-Conrad-Str.1,D-92240Hirschau(www.conrad.com).

Allrightsincludingtranslationreserved.Reproductionbyanymethod,e.g.photocopy,microlming,orthecaptureinelectronicdataprocessing

systemsrequirethepriorwrittenapprovalbytheeditor.Reprinting,alsoinpart,isprohibited.Thispublicationrepresentthetechnicalstatusat

thetimeofprinting.

Page is loading ...

Reely 1600322 Operating instructions

Brand: Reely

Model: 1600322

Type: Operating instructions

Download PDF

report

in other languages

français: Reely 1600322 Mode d'emploi
Deutsch: Reely 1600322 Bedienungsanleitung
Nederlands: Reely 1600322 Handleiding

Reely 1600322 Operating instructions

Reely 1600322 Operating instructions

in other languages

Related papers

Other documents