Fiat 124 Spider Abarth Owner's manual

OWNER’S MANUAL

2018

FIAT

®

124 SPIDER ABARTH

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name

FCA US LLC shall be deemed to be deleted and the name

FCA Canada Inc. used in substitution therefore.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of

accidents.

Your driving ability can be seriously impaired with blood

alcohol levels far below the legal minimum. If you are

drinking, don’t drive. Ride with a designated non-

drinking driver, call a cab, a friend, or use public trans-

portation.

WARNING!

Driving after drinking can lead to an accident.

Your perceptions are less sharp, your reflexes are

slower, and your judgment is impaired when you

have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of

features and equipment that are either standard or op-

tional on this vehicle. This manual may also include a

description of features and equipment that are no longer

available or were not ordered on this vehicle. Please

disregard any features and equipment described in this

manual that are not on this vehicle.

FCA US LLC reserves the right to make changes in design

and specifications, and/or make additions to or improve-

ments to its products without imposing any obligation

upon itself to install them on products previously manu-

factured.

DEAR CUSTOMER

Dear Customer,

We would like to congratulate and thank you for choosing a Fiat 124 Spider.

We have written this Owner’s Manual to help you get to know all the features of your vehicle and use it in the best possible way.

Here you will find information, advice and important warnings regarding use of your vehicle and how to achieve the best

performance from the technical features of your vehicle.

You are advised to take the time to read these publications carefully before taking to the road for the first time, to become

familiar with the controls and above all with those concerning brakes, steering and transmission; at the same time, you can

understand the vehicle behavior on different road surfaces.

This document also provides a description of special features and tips, as well as essential information for the safe driving, care

and maintenance of your vehicle over time.

After reading it, you are advised to keep the Owner’s Manual inside the vehicle, for an easy reference and for making sure it

remains in the vehicle should it be sold.

In the attached Warranty Booklet you will also find a description of the Services that FCA offers to its customers, and the detail

of the terms and conditions for maintaining its validity.

We are sure that these will help you to get in touch with and appreciate your new vehicle and the service provided by the

people at FCA.

Enjoy reading. Happy motoring!

Note: This Owner’s Manual describes all models of the vehicle; please consider only the information relevant to your vehicle’s

trim level, engine and model. All data contained in this publication are purely indicative. FCA can modify the vehicle model

described in this publication at any time, for technical or commercial purposes. For further information, contact your authorized

dealer.

Read This Carefully

REFUELING

Only refuel with unleaded gasoline with a recommended rating of 91 octane. A rating less than 87 octane is not acceptable. Do not use

gasoline containing methanol or ethanol E85. Using these mixtures may cause misfiring and handling issues, as well as damage fundamental

components of the fuel supply system.

STARTING THE ENGINE

If equipped with a manual transmission: Be sure that the parking brake is engaged; place the gear selector in NEUTRAL, fully depress the

clutch pedal without pressing the accelerator, and then push the ignition button. The engine will start as soon as the ignition is pushed.

If equipped with an automatic transmission: Be sure that the parking brake is engaged and that the gear selector is in PARK (P) or

NEUTRAL (N), depress the brake pedal, and then push the ignition button. The engine will start as soon as the ignition is pushed.

PARKING ON FLAMMABLE MATERIAL

The catalytic converter develops high temperatures during operation. Do not park the vehicle on grass, dry leaves, pine needles or other

flammable material: fire hazard.

RESPECTING THE ENVIRONMENT

The vehicle is equipped with a system that carries out a continuous diagnosis of the emission-related components in order to help protect the

environment.

ELECTRICAL ACCESSORIES

Contact your authorized dealer if you decide to add electrical accessories (with the risk of gradually draining the battery) after buying the

vehicle. They can calculate the overall electrical requirement and check that the vehicle's electric system can support the required load.

SCHEDULED SERVICING

Correct maintenance of the vehicle is essential for ensuring that it maintains its performance and its safety features, its environmental

friendliness and low running costs are unchanged over time.

How To Use This Manual

ESSENTIAL INFORMATION

Each time directions (left/right or forward/backwards) are listed, they are determined by facing forward from the rear of the

vehicle or as from the point of view of being seated inside the car. Special cases not complying with this rule will be properly

specified in the text.

The figures in the Owner’s Manual are provided by way of example only: this might imply that some details of the image do not

correspond to the actual arrangement of your vehicle. In addition, the Owner’s Manual has been conceived considering vehicles

with steering wheel on the left side; it is therefore possible that on vehicles with steering wheel on the right side, the position of

some controls or elements is not exactly mirror-like with respect to the figure.

To identify the chapter with the information needed you can consult the index at the end of this Owner’s Manual.

Chapters can be rapidly identified by graphic tabs, at the side of each odd page. A key showing the order of the chapter and

the corresponding tab symbols appears on another page.

SYMBOLS

While reading this Owner’s Manual you will find a series of WARNINGS that must be carefully followed to prevent incorrect use

of the components of the vehicle, which could cause accidents or injuries.

There are also CAUTIONS that must be carefully followed prevent procedures that could damage your vehicle.

Therefore, all WARNINGS and CAUTIONS must always be carefully followed.

WARNINGS and CAUTIONS are recalled in the text with the following symbols:

Personal Safety

Vehicle Safety

Vehicle Modifications / Alterations

Warning!

Any change or alteration of the vehicle might seriously affect its safety and road holding, thus causing accidents, in which the occupants

could be fatally injured.

ACCESSORIES PURCHASED BY THE OWNER

If after buying the vehicle, you decide to install electrical accessories that require a permanent electrical supply (e.g. radio,

satellite anti-theft system, etc.) or accessories that burden the electrical supply, contact your authorized dealer, whose

personnel will check whether the vehicles's electrical system is able to withstand the load required , or whether it needs to be

integrated with a more powerful battery.

Note: Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of

position and interfere with the pedals or impair safe operation of your vehicle in other ways.

INSTALLING ELECTRICAL / ELECTRONIC DEVICES

The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle:

This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

RADIO TRANSMITTERS AND MOBILE PHONES

Radio transmitter equipment (vehicle mobile phones, CB radios, amateur radio etc.) cannot be used inside the vehicle unless a

separate aerial is mounted externally.

Transmission and reception of these devices may be affected by the shielding effect of the vehicle body. As far as the use of

EC-approved mobile phones is concerned (GSM, GPRS, UMTS, LTE), follow the usage instructions provided by the mobile

phone Manufacturer.

The use of these devices inside the vehicle (without an external aerial) may cause the electrical systems to malfunction. This

could compromise the vehicle safety in addition to constituting a potential hazard for passengers' health.

If mobile phones/laptops/smartphones/tablets are inside the vehicle and/or close to the electronic key, a reduced performance

of the Advanced Keyless Entry System may occur.

CELL PHONE WARNING

Note: Please comply with the legal regulations concerning the use of communication equipment in vehicles in your country.

Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver

while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver's hands. Use of

these devices will cause the driver to be distracted and could lead to a serious accident. If a passenger is unable to use the

device, pull off the right-of-way to a safe area before use. If use of a cell phone is necessary despite this warning, use a

hands-free system to at least leave the hands free to drive the vehicle. Never use a cell phone or other electrical devices while

the vehicle is moving and, instead, concentrate on the full-time job of driving.

This page is intentionally left blank

GRAPHICAL TABLE OF CONTENTS

GETTING TO KNOW YOUR VEHICLE

GETTING TO KNOW YOUR INSTRUMENT

PANEL

SAFETY

STARTING AND OPERATING

IN CASE OF EMERGENCY

SERVICING AND MAINTENANCE

TECHNICAL SPECIFICATIONS

CUSTOMER ASSISTANCE

INDEX

This page is intentionally left blank

GRAPHICAL TABLE OF CONTENTS

FRONT VIEW

01020304-000-100AB

Front View

1 — Wheels And Tires 3 — Headlights 5 — Convertible Top

2 — Windshield Wiper Blades 4 — Engine Compartment

9

REAR VIEW

01020304-001-100AB

Rear View

1 — Decklid 3 — Exterior Mirror

2 — Taillight 4 — Wheels/Tires

10

INSTRUMENT PANEL

02010200-129-555AB1

Instrument Panel

1 — Turn Signal/High Beams Lever 4 — Hazard Warning Lights Button 7 — Driver Air Bag

2 — Instrument Cluster 5 — Passenger Air Bag

3 — Windshield Wiper And Washers 6 — Ignition Switch

11

INTERIOR OVERVIEW

01020304-002-100AB1

Interior Overview

1 — Instrument Cluster 4 — Climate Control System 7 — Seats

2 — Steering Wheel 5 — Transmission Gear Selector 8 — Radio Controls

3 — Radio Systems 6 — Parking Brake

12

GETTING TO KNOW YOUR VEHICLE

KEYS ....................14

IGNITION SWITCH ............20

ADVANCED KEYLESS ENTRY

SYSTEM — IF EQUIPPED .......21

VEHICLE SECURITY ALARM

SYSTEM — IF EQUIPPED .......23

DOORS...................26

SEATS ...................33

NON-ADJUSTABLE HEAD

RESTRAINTS ...............34

STEERING WHEEL ...........35

MIRRORS .................35

EXTERIOR LIGHTS ...........38

WINDSHIELD WIPERS / WASHER .43

CLIMATE CONTROL SYSTEM ....45

POWER WINDOWS ...........56

HOMELINK — IF EQUIPPED .....58

INTERNAL EQUIPMENT ........60

TRUNKLID ................65

TRUNK EMERGENCY RELEASE . . .67

HOOD ...................68

CONVERTIBLE TOP (SOFT TOP) . .70

ELECTRIC POWER STEERING ....74

ENVIRONMENT PROTECTION

SYSTEMS .................74

13

KEYS

Key Fob

A code number is stamped on the plate

and attached to the key fob. Detach

this plate and store it in a safe place

(not in the vehicle) if you need to make

replace the Emergency Key.

Also, write down the code number and

keep it in a separate safe and convenient

place. Do not keep it in the vehicle.

If your key fob is lost, contact an

authorized dealer.

Note: Your key fob configuration may

vary with equipped features. Please see

the example shown below:

To use the Emergency Key, push the

mechanical latch on the back side of the

key fob and pull out the emergency key.

Note:

Always keep a spare key fob if one

is lost. If a key fob is lost, see an

authorized dealer as soon as possible.

The driver must carry the key fob to

ensure the Keyless Entry System

functions properly.

Warning!

Before exiting a vehicle, always shift the

automatic transmission into PARK or the

manual transmission into FIRST gear or

REVERSE, apply the parking brake, then

turn the engine OFF, remove the key fob

from the vehicle and lock your vehicle.

Never leave children alone in a vehicle,

or with access to an unlocked vehicle.

Allowing children to be in a vehicle

unattended is dangerous for a number of

reasons. A child or others could be

seriously or fatally injured. Children should

be warned not to touch the parking brake,

brake pedal or the gear selector.

Do not leave the key fob in or near the

vehicle, or in a location accessible to children.

A child could operate power windows, other

controls, or move the vehicle.

Do not leave children or animals inside

parked vehicles in hot weather. Interior heat

build-up may cause serious injury or death.

Key Fob Functions

With A Vehicle Security Alarm

System

The hazard warning lights will flash

when the vehicle security alarm system

is armed or disarmed.

With Advanced Keyless Function

A beep will sound when the doors,

trunk lid, and fuel filler door are locked

or unlocked using the key fob. The

beep volume can be adjusted or turned

off.

Use the following procedure to change

the beep setting:

1. Place the ignition in the OFF position

and close the doors and the trunk lid.

2. Open the driver's door.

3. Within 30 seconds of opening the

driver's door, push and hold the lock

button on the key fob for five seconds.

Note:

The doors, trunk lid, and fuel filler

door will lock, and the beep will

activate at the current volume (if the

beep is currently set to not activate, it

will not activate).

The setting changes when the lock

button on the key fob is pushed, and

the beep will activate at the set volume

(if the beep sound has been set to not

activate, it will not activate).

04010100-361-002AB

Key Fob

1 — Emergency Key

2 — Key Fob

3 — Key Code Number Plate

14

GETTING TO KNOW YOUR VEHICLE

Complete changing the setting by doing

the following:

Placing the ignition in ACC or ON

position.

Closing the driver's door.

Opening the trunk lid.

Not operating the key fob for ten

seconds.

Pushing any button, except the lock

button on the key fob.

Pushing a request switch on the

exterior door handle.

Note: Refer to “Lock/Unlock With

Advanced Keyless Entry Function — If

Equipped” in “Doors” for further

information.

The operation indicator light flashes

when the buttons are pushed.

Key Fob Buttons

Lock Button

To lock the doors, trunk lid, and fuel

filler door, push the lock button on the

key fob. The hazard warning lights will

flash once and a beep will sound.

Unlock Button

To unlock the doors and trunk lid, push

the unlock button on the key fob, and

the hazard warning lights will flash

twice.

The system can be set to unlock both

doors. Use the following procedure to

change the setting:

1. Place the ignition in the OFF position

and close the doors and trunk lid.

2. Open the driver's door.

3. Within 30 seconds of opening the

driver's door, push and hold the unlock

button on the key fob for five seconds.

Note: The sound of the doors

locking/unlocking can be heard. After

this, the system will change the setting

when the unlock button is pushed (the

sound of the doors locking/unlocking

can be heard).

The setting change can be completed

by doing any one of the following:

Placing the ignition in the ACC or ON

position.

Closing the driver’s door.

Opening the trunk lid.

Not operating the key fob for ten

seconds.

Pushing any button except the

unlock button on the key fob.

Pushing a request switch on the

exterior door handle.

Trunk Button

To open the trunk lid, push and hold the

trunk button until the trunk lid opens.

Panic Button

To turn the Panic Alarm on or off, push

and hold the Panic button on the key fob

and release. When the Panic Alarm is on,

the headlights will turn on, the park lights

will flash, the horn will pulse on and off,

and the turn signal lights will flash.

Note: The panic button will work if the

doors or trunk are opened or closed.

Turning On The Alarm

Pushing the panic button for one

second or more will trigger the alarm for

about two minutes and thirty seconds,

and the following will occur:

The horn sounds intermittently.

The hazard warning lights flash.

Turning Off The Alarm

The alarm will stop by pushing any

button on the key fob.

Operational Range

The system operates only when the

driver is in the vehicle or within

operational range, and the key fob is

being carried.

Starting The Engine

Starting the engine may be possible

even if the key fob is outside the vehicle

and close to a door or window. Always

start the engine from the driver's seat.

If the vehicle is started, and the key fob

is not in the vehicle, the vehicle will not

restart after it is shut off. The ignition is

placed in the OFF position.

15

Key Fob Antenna Location

Note: The engine may not start if the

key fob is placed in or around the

following areas:

Around The Instrument Panel

In The Storage Compartments

Key Suspend Function

If a key fob is left in the vehicle, key fob

functions are temporarily suspended to

prevent unlawful use of the vehicle.

To restore the functions, push the

unlock button on the functions-

suspended key fob.

Key Fob Battery

Replacement

If key fob does not work, and the

indicator lights do not flash, the battery

may be low or discharged.

Replace with a new battery

(CR2025 type) before the key fob

becomes unusable.

The following conditions indicate that

the battery power is low:

Indicator light (green) flashes in

the instrument cluster for about

30 seconds after the engine is placed in

the OFF position.

The system does not operate, and

the operation indicator light on the key

fob does not flash when the buttons are

pushed.

The system's operational range is

reduced.

Note: Replacing the battery at an

authorized dealer is recommended to

prevent damage to the key fob. If

replacing the battery by yourself, follow

the instruction below.

Replacing The Key Fob Battery

Proceed as follows:

1. Push the mechanical release button

and remove the emergency key.

1 — Key Fob Case With Mechanical

Release Button

2 — Emergency Key

2. Insert a coin, a flat blade screw

driver, or the tip of your emergency key

into the now exposed slot and carefully

pry in the direction of the arrows to

open the cover (3) slightly.

04010202-12R-001

Key Fob Antenna Location

1 — Interior Antenna

2 — Operational Range

07031301-361-002

Emergency Key Removed

07031301-362-002

3 — Pry Case Left Side

16

GETTING TO KNOW YOUR VEHICLE

3.

Insert a coin, a flat blade screw driver,

or the tip of your emergency key into the

side gap and carefully pry in the direction

of the arrow to open the cover (4).

4. Separate the key fob case, then

remove the battery.

3 — Key Fob Case

5 — Key Fob Battery

5. Insert a new battery with the positive

pole facing up. Then, cover the battery

with the battery cap.

6. Close the cover and reinsert the

Emergency Key.

Note: Be careful not to allow the

rubber ring shown in call-out (6) to be

scratched or damaged. If the rubber

ring comes out, reinstall it before

inserting a new battery.

Engine Start Function

When Key Fob Battery Is

Discharged

If a key fob has discharged or

malfunctioned, start the engine by

holding the Key Fob over the keyless

ignition START/STOP button. Be careful

to not to allow the following. The signal

from the key fob will not be received

correctly, and the engine may not start:

Contact with metal parts of other key

fobs or metal objects.

Contact from key fobs from other

vehicle’s equipped with an immobilizer

system.

Contact with devices for electronic

purchases or security passage touch.

07031301-363-002

4 — Pry Case Right Side

07031301-364-003

Remove Back Cover For Battery

Replacement

07031301-367-001

6 — Install New Battery

05010201-KY1-001AB

No Keys Touching The Key Fob

05010201-KY2-001AB

No Key Fob Touching The Key Fob

17

If the engine cannot be started due to a

discharged key fob battery, the engine

can be started using the following

procedure:

1.

Continue to depress the brake pedal

firmly until the engine has completely

started.

2. Manual Transmission: Continue to

depress the clutch pedal firmly until the

engine has completely started.

3. Verify that the keyless ignition start

indication light (green) flashes.

4.

Touch the keyless ignition

START/STOP button using the backside

of the key fob while the keyless ignition

start indicator light (green) flashes.

5. Verify that the keyless ignition start

indicator light (green) turns on.

6.

Push the keyless ignition

START/STOP button to start the engine.

When touching the keyless ignition

START/STOP button using the

backside of the key fob, touch the

keyless ignition START/STOP button

with the key fob buttons facing up.

The engine cannot be started unless

the clutch pedal is fully depressed

(manual transmission) or the brake

pedal is fully depressed (automatic

transmission).

If there is a malfunction with the keyless

ignition START/STOP button function,

the keyless ignition start indicator light

(amber) flashes. In this case, the engine

may start. However, contact an

authorized dealer as soon as possible.

If the keyless ignition start indicator light

(green) does not illuminate, perform the

operation from the beginning. If it does

not illuminate, contact an authorized

dealer.

To change the ignition position without

starting the engine, perform the

following operations after the keyless

ignition start indicator light (green) turns

on:

1. Release the clutch pedal (manual

transmission) or brake pedal (automatic

transmission).

2. Push the keyless ignition

START/STOP button to change the

ignition position. The ignition cycles in

the order of ACC, ON, and OFF each

time the keyless ignition START/STOP

button is pushed.

Note: To change the ignition position

again, perform the operation from the

beginning.

Emergency Operation For Starting

The Engine

If the key warning light (red) illuminates,

or the keyless ignition start indicator

light (amber) flashes, this could indicate

that the engine may not start using the

usual starting method. Contact an

authorized dealer as soon as possible.

If this occurs, the engine can be

force-started. push and hold the

keyless ignition START/STOP button

until the engine starts.

Other procedures necessary for starting

the engine such as having the key fob

in the vehicle, and depressing the

clutch pedal (manual transmission) or

the brake pedal (automatic

transmission) are required.

05010201-L12-0011

Discharged Key Fob Battery Start

Procedure

18

GETTING TO KNOW YOUR VEHICLE

Page is loading ...

Fiat 124 Spider Abarth, 2018 124 Spider Abarth Owner's manual

Related papers

Other documents