GE 363.63672 User manual

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Above the

Instructions Cooktop Oven

JVM1600 Series

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer

–

Be sure to leave these

instructions with the Consumer.

BEFORE YOU BEGIN

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

3828W5U0477

49-40469-1

09-06 JR

2
Recirculating ........................................ 19–22
Attach Mounting Plate to Wall ............19
Preparation of Top Cabinet ................19
Adapting Blower for 
Recirculation ................................20, 21
Mount the Oven............................21, 22
Installing the Charcoal Filter ..............22
Before You Use Your Oven  .................................. 23
CONTENTS
General information
Important Safety Instructions .................................. 3
Electrical Requirements .......................................... 3
Hood Exhaust ...................................................... 4, 5
Damage—Shipment/Installation.............................. 6
Parts Included.......................................................... 6
Tools You Will Need ................................................ 7
Mounting Space ...................................................... 7
Step-by-step installation guide
Placement of Mounting Plate ............................ 8–10
Removing the Mounting Plate ...................... 8
Finding the Wall Studs .................................. 8
Determining Wall Plate Location .................. 9
Aligning the Wall Plate................................ 10
Installation Types.............................................. 11–22
Outside Top Exhaust ............................ 12–14
Attach Mounting Plate to Wall ............12
Preparation of Top Cabinet ................13
Assemble and Install Adaptor ..............13
Mount the Oven ............................13, 14
Adjust the Exhaust Adaptor ................14
Connecting Ductwork..........................14
Outside Back Exhaust............................ 15–18
Preparing Rear Wall for 
Outside Back Exhaust..........................15
Attach Exhaust Adaptor to 
Oven Rear Panel..................................15
Attach Mounting Plate to Wall ............16
Preparation of Top Cabinet ................16
Adapting Blower for Outside 
Back Exhaust..........................................17
Mount the Oven ..................................18
A
B
C
Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.

The installer must perform a ground continuity check

on the power outlet box before beginning the

installation to insure that the outlet box is properly

grounded. If not properly grounded, or if the outlet

box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualified

electrician should be employed to correct any

deficiencies.

CAUTION:

For personal safety, remove

house fuse or open circuit

breaker before beginning

installation to avoid severe

or fatal shock injury.

CAUTION: For personal safety, the mounting

surface must be capable of supporting the cabinet load,

in addition to the added weight of this 63–85 pound

product, plus additional oven loads of up to 50 pounds

or a total weight of 113–135 pounds.

CAUTION: For personal safety, this product

cannot be installed in cabinet arrangements such as an

island or a peninsula. It must be mounted to BOTH

a top cabinet AND a wall.

NOTE: For easier installation and personal safety, it is

recommended that two people install this product.

IMPORTANT—PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

The power cord of this

appliance is equipped with

a three-prong (grounding)

plug which mates with

a standard three-prong

(grounding) wall receptacle

to minimize the possibility

of electric shock hazard

from this appliance.

You should have the wall receptacle and circuit checked

by a qualified electrician to make sure the receptacle is

properly grounded.

Where a standard two-prong wall receptacle is

encountered, it is very important to have it replaced

with a properly grounded three-prong wall receptacle,

installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

3

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 14 amps and

1.60 kilowatts. This product must be connected to a

supply circuit of the proper voltage and frequency.

Wire size must conform to the requirements of the

National Electrical Code or the prevailing local code

for this kilowatt rating. The power supply cord and

plug should be brought to a separate 15 to 20 ampere

branch circuit single grounded outlet. The outlet box

should be located in the cabinet above the oven. The

outlet box and supply circuit should be installed by

a qualified electrician and conform to the National

Electrical Code or the prevailing local code.

Insure proper

ground exists

before use

Installation Instructions

4

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Roof Cap 24 Ft. x (1) = 24 Ft.

12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft.

(6″ Round)

Rectangular-to-Round 5 Ft. x (1) = 5 Ft.

Transition Adaptor*

Equivalent lengths of duct pieces are based on actual tests and

reflect requirements for good venting performance with any vent hood.

Total Length = 41 Ft.

HOOD EXHAUST

The following chart describes an example of one possible

ductwork installation.

NOTE: Read these next two pages only if you plan to vent your exhaust to the

outside. If you plan to recirculate the air back into the room, proceed to page 6.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

*IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will

have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

The following chart describes an example of one possible

ductwork installation.

Installation Instructions

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH* x USED = LENGTH

Wall Cap 40 Ft. x (1) = 40 Ft.

3 Ft. Straight Duct 3 Ft. x (1) = 3 Ft.

(3

1

⁄

4

″ x 10″ Rectangular)

90° Elbow 10 Ft. x (2) = 20 Ft.

Equivalent lengths of duct pieces are based on actual tests and

reflect requirements for good venting performance with any vent hood.

Total Length = 63 Ft.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Rectangular-to-Round 5 Ft. x ( ) = Ft.

Transition Adaptor*

Wall Cap 40 Ft. x ( ) = Ft.

90° Elbow 10 Ft. x ( ) = Ft.

45° Elbow 5 Ft. x ( ) = Ft.

90° Elbow 25 Ft. x ( ) = Ft.

45° Elbow 5 Ft. x ( ) = Ft.

Roof Cap 24 Ft. x ( ) = Ft.

Straight Duct 6″ Round or 1 Ft. x ( ) = Ft.

3

1

⁄4″ x 10″ Rectangular

Total Ductwork = Ft.

Equivalent lengths of duct pieces are based on actual tests

and reflect requirements for good venting performance with

any vent hood.

* IMPORTANT: If a rectangular-to-round transition

adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, in order

to allow free movement of the damper

.

NOTE: If you need to install ducts, note that the total

duct length of 3

1

⁄4″ x 10″ rectangular or 6″ diameter

round duct should not exceed 120 equivalent feet.

Outside ventilation requires a HOOD EXHAUST DUCT.

Read the following carefully.

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate with a

standard 3

1

⁄4″ x 10″ rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor must be used. Do not use less than

a 6″ diameter duct.

Maximum duct length:

For satisfactory air movement, the total duct length of

3

1

⁄4″ x 10″ rectangular or 6″ diameter round duct should

not exceed 120 equivalent feet.

Elbows, transitions, wall and roof caps,

etc.,

present additional resistance to airflow and are

equivalent to a section of straight duct which is longer

than their actual physical size. When calculating the

total duct length, add the equivalent lengths of all

transitions and adaptors plus the length of all straight

duct sections. The chart below shows you how to

calculate total equivalent ductwork length using the

approximate feet of equivalent length of some

typical ducts.

5

Installation Instructions

PART

QUANTITY

Top Cabinet 1

Template

Rear Wall 1

Template

Installation 1

Instructions

Separately 2

Packed

Grease

Filters

Charcoal 1

Filter

(on some

models)

Exhaust 1

Adaptor

Damper 1

PART QUANTITY

Wood Screws 2

(

1

⁄4″ x 2″)

Toggle Bolts (and 4

wing nuts) (

1

⁄4″ x 3″)

Self-aligning Machine 3

Screws (

1

⁄4″-28 x 3

1

⁄4″)

Nylon Grommet 2

(for metal cabinets)

Metal Screws 1 black

(

1

⁄8″ x

1

⁄2″) 2 bronze

Power Cord Strap 1

(plastic)

6

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for repair

or replacement.

• If the unit is damaged by the customer, repair or

replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer and

installer.

DAMAGE – SHIPMENT/

INSTALLATION

PARTS INCLUDED

ADDITIONAL PARTS

Installation Instructions

PARTS INCLUDED

You will find the installation hardware contained in

a packet with the unit. Check to make sure you have

all these parts.

NOTE: Some extra parts are included.

HARDWARE PACKET

7

TOOLS YOU WILL NEED

# 1 and #2 Phillips screwdriver

Pencil

Ruler or tape measure

and straight edge

Carpenter square

(optional)

Tin snips (for cutting

damper, if required)

Electric drill with

3

⁄16″,

7

⁄16″,

3

⁄8″,

1

⁄2″ and

5

⁄8″ drill bits

Hammer (optional)

Stud finder or

Filler blocks or scrap

wood pieces, if needed

for top cabinet spacing

(used on recessed bottom

cabinet installations only)

Gloves

Saw (saber, hole or keyhole)

Level

Duct and masking tape

MOUNTING SPACE

NOTES:

• The space between the cabinets must be 30″

wide and free of obstructions.

• If the space between the cabinets is greater

than 30″, a Filler Panel Kit may be used to fill

in the gap between the oven and the cabinets.

Your Owner’s Manual contains the kit number

for your model.

• This oven is for installation over ranges up to

36″ wide.

• If you are going to vent your oven to the outside,

see Hood Exhaust Section for exhaust duct

preparation.

• When installing the oven beneath smooth, flat

cabinets, be careful to follow the instructions

on the top cabinet template for power cord

clearance.

Backsplash

66″ or more

from the floor

to the top of

the oven

30″

2″

30″

min.

16-

1

⁄

4

″

Bottom edge of

cabinet needs to

be 30″ or more

from the cooking

surface

Installation Instructions

Scissors

(to cut template, if necessary)

Safety goggles

NOTE: Maximum cabinet depth is 13".

8

Find the studs, using one of the following

methods:

A. Stud finder – a magnetic device which

locates nails.

OR

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound.

This will indicate a stud location.

After locating the stud(s), find the center by

probing the wall with a small nail to find the

edges of the stud. Then place a mark halfway

between the edges. The center of any adjacent

studs should be 16″ or 24″ from this mark.

Draw a line down the center of the studs.

THE OVEN MUST BE CONNECTED TO AT LEAST

ONE WALL STUD.

1

Remove the turntable, installation instructions,

filters, exhaust adaptor, damper, shelf and the

small hardware bag. Do not remove the Styrofoam

protecting the front of the oven.

Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton over

onto the top side. The oven should be resting in

the Styrofoam.

REMOVING THE OVEN FROM

THE CARTON/REMOVING THE

MOUNTING PLATE

FINDING THE WALL STUDS

B

.

A

.

2

PLACEMENT OF THE MOUNTING PLATE

1

Wall

Studs

Center

3

Carton

Pull the carton up and off the oven.

Open the oven door and remove any packing

material, if present, from inside the oven.

2

Styrofoam

Installation Instructions

3

6

Set the oven upright. Remove and properly discard

plastic bags and Styrofoam.

5

1

The mounting plate is attached to the back of the

oven. Remove the two screws holding it to the oven.

The plate will be used as the rear wall template and

for mounting the oven to the wall.

4

9

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

C.

Your cabinets may have decorative trim that interferes

with the oven installation. Remove the decorative trim

to install the oven properly and to make it level.

THE OVEN MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no

back or side frame, install the mounting plate down

the same distance as the front overhang depth. This

will keep the oven level.

Measure the inside depth of the front overhang.

Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside

depth of the front overhang.

For this type of installation with front overhang only,

align the mounting tabs with this horizontal line, not

touching the cabinet bottom as described in Step D.

Plate position – beneath flat bottom

cabinet

Plate position – beneath recessed bottom

cabinet with front overhang

Mounting Plate Tabs

Touching the Cabinet

Bottom

Mounting Plate with

Tabs Below Cabinet

Bottom the Same

Distance as the Front

Overhang Depth

At least 30″, up to 36″

Plate position – beneath framed recessed

cabinet bottom

Mounting Plate Tabs

Touching the Back

Frame

Installation Instructions

30″ to Cooktop

1

2

3

10

ALIGNING THE WALL PLATE

Draw a vertical line on the wall at the center of the 30″

wide space.

Use the mounting plate as the template for the rear

wall. Place the mounting plate on the wall, making

sure that the tabs are touching the bottom of the

cabinet or the level line drawn in Step C for cabinets

with front overhang. Line up the notch and center line

on the mounting plate to the center line on the wall.

While holding the mounting plate with one hand,

draw circles on the wall at holes A, B, C and D (see

illustration above/actual plate marked with arrows).

Four holes must be used for mounting.

NOTE: Holes C and D are inside area E. If neither

C nor D is in a stud, find a stud somewhere in area E

and draw a fifth circle to line up with the stud. It is

important to use at least one wood screw mounted

firmly in a stud to support the weight of the oven.

Set the mounting plate aside.

Drill holes on the circles. If there is a stud, drill a

3

⁄16″

hole for wood screws. For holes that don’t line up with

a stud, drill a

5

⁄8″ hole for toggle bolts.

NOTE: DO NOT MOUNT THE PLATE

AT THIS TIME.

2

3

4

Draw a Vertical

Line on Wall

from Center of

Top Cabinet

Area E

Hole A

Hole B

Hole D

Hole C

D.

Installation Instructions

CAUTION: Wear gloves

to avoid cutting fingers on

sharp edges.

1

NOTE: Appearance and

shape of the mounting

plate may vary from your

model.

A

INSTALLATION TYPES (Choose A, B or C)

This oven is designed for adaptation to the following three

types of ventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Outside Back Exhaust (Horizontal Duct)

C. Recirculating (Non-Vented Ductless)

NOTE: This oven is shipped assembled for Outside Top

Exhaust (except for non-vented models). Select the type

of ventilation required for your installation and proceed

to that section.

OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

RECIRCULATING

(NON-VENTED DUCTLESS)

See page 12

See page 15

See page 19

On models shipped for

non-vented exhaust, a

disposable charcoal filter is

included with the oven and

needs to be installed to help

remove smoke and odors.

On models shipped for

outside top exhaust, a

Charcoal Filter Accessory Kit

is required for the non-vented

exhaust. (See your Owner’s

Manual for the kit number.)

Installation Instructions

2

B

C

11

Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall to

mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed

flush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

3

A

4

ATTACH THE MOUNTING

PLATE TO THE WALL

A1.

12

OUTSIDE TOP EXHAUST (Vertical Duct)

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach the plate to a

wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate

through the holes designated to go into drywall

and reattach the toggle wings to

3

⁄4″ onto each bolt.

1

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top Cabinet

A3. Install Adapter

A4. Mount Oven

A5. Adjust Exhaust Adaptor

A6. Connect Ductwork

Wall

Mounting

Plate

Spacing for Toggles

More Than Wall

Thickness

Bolt End

Toggle

Bolt

Toggle Wings

To use toggle bolts:

Installation Instructions

2

13

2

Rotate front of oven

up against cabinet

bottom.

1

MOUNT THE OVEN

A4.

ASSEMBLE AND

INSTALL ADAPTOR

A3.

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws, a

hole large enough for the power cord to fit through,

and a cutout large enough for the exhaust adaptor.

A2.

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from over

tightening screws.

NOTE: When mounting the

oven, thread power cord

through hole in bottom

of top cabinet. Keep it tight

throughout Steps 1–3.

Do not pinch cord or lift

oven by pulling cord.

Lift oven, tilt it

forward and hook

slots at back bottom

edge onto two lower

tabs of mounting

plate.

Damper

Back of

Oven

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

Installation Instructions

Place the oven in its upright position, with the top

of the unit facing up.

NOTE: Make sure the blower fan blades are visible

and are pointing up.

Insert the tabs on each side of the damper into the

holes at the inside rear of the adaptor.

Attach the exhaust adaptor to the blower plate with

the two bronze metal screws provided.

Make sure that the damper pivots easily before

mounting oven.

You will need to make adjustments to assure proper

alignment with your house exhaust duct after the

oven is installed.

Exhaust

Adaptor

1

2

Blower Plate

3

NOTE: On some models, the exhaust adaptor and

damper assembly may already be assembled to the oven.

Attach the oven to the top cabinet by inserting

3 self-aligning screws through outer top cabinet

holes. Turn two full turns on each screw. Be sure

to keep power cord tight. Be careful not to pinch

the cord, especially when mounting flush to

bottom of cabinet.

3

14

5

4

Cabinet Front

Cabinet Bottom Shelf

Tighten the three screws to the top of the oven

completely. (While tightening screws, hold the

oven in place against the wall and the top cabinet.)

Filler Block

Oven Top

Equivalent

to Depth

of Cabinet

Recess

Install grease filters. See the Owner’s Manual

packed with the oven.

Installation Instructions

ADJUST THE EXHAUST

ADAPTOR

A5.

Open the top cabinet and adjust the exhaust adaptor

to connect to the house duct.

CONNECTING DUCTWORK

1

2

Extend the house duct down to connect to

the exhaust adaptor.

Seal exhaust duct joints using duct tape.

A6.

House Duct

Self-Aligning Screw

MOUNT THE OVEN (continued)

A4.

Back of

Oven

Damper

Attach the exhaust adaptor to the oven rear

panel by sliding it into the guides at the top

center of the back of the oven.

OUTSIDE BACK EXHAUST (Horizontal Duct)

PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

B1.

INSTALLATION OVERVIEW

B1. Prepare Rear Wall

B2. Attach Exhaust Adaptor to

Wall Plate

B3. Attach Mounting Plate

to Wall

B4. Prepare Top Cabinet

B5. Adjust Blower

B6. Mount the Oven

Installation Instructions

B

Read the instructions on the REAR WALL

TEMPLATE.

Tape it to the rear wall, lining up with the holes

previously drilled for holes A and B in the wall

plate.

Cut the opening, following the instructions of the

REAR WALL TEMPLATE.

15

3

2

1

Unscrew and remove the exhaust adaptor

assembly from the top of the oven.

1

2

Exhaust Adaptor

Damper

(hinge side up)

Locking

Tabs

Guide

ATTACH THE EXHAUST

ADAPTOR TO THE OVEN REAR

PANEL

B2.

Guide

Push in securely until it is in the lower locking tabs.

Take care to assure the damper hinge is installed so

that it is at the top and that the damper swings freely.

You need to cut an opening in the rear wall for

outside exhaust.

Exhaust

Adaptor

16

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

B4.

•

Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in

the cabinet bottom.

Wall

Mounting

Plate

Spacing for Toggles More

Than Wall Thickness

Toggle

Bolt

Toggle Wings

To use toggle bolts:

Bolt End

Installation Instructions

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed flush

against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

3

4

ATTACH THE MOUNTING

PLATE TO THE WALL

B3.

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach the plate to a

wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate through

the holes designated to go into drywall and reattach

the toggle wings to

3

⁄4″ onto each bolt.

1

2

Place the blower unit back into the opening.

Roll the blower unit 90° so that fan blade

openings are facing out the back of the

oven.

4

BEFORE: Fan Blade

Openings Facing Up

AFTER: Fan

Blade Openings

Facing Back

2

1

Remove the two screws that hold the blower plate

and remove the screw holding the blower motor

to the oven. Slide blower plate from under its

retaining flange.

ADAPTING BLOWER FOR

OUTSIDE BACK EXHAUST

B5.

17

Carefully pull out the blower unit. The wires

will extend far enough to allow you to adjust

the blower unit.

Blower Plate

Replace the blower plate in the same position

as before and replace the screws for the

blower plate and blower motor.

Before Rolling

After Rolling

Back of Oven

Back of

Oven

Back of

Oven

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not pinched.

NOTE: The blower unit exhaust openings should

match exhaust openings on rear of oven.

Installation Instructions

Retaining

Flange

Blower Plate Screws

Back of

Oven

3

Rotate blower unit counterclockwise 180°.

Before Rotation After Rotation

Back of

Oven

Back of

Oven

5

6

Blower Motor Screw

Attach the oven to the top cabinet by inserting

3 self-aligning screws through outer top cabinet

holes. Turn two full turns on each screw. Be sure

to keep power cord tight. Be careful not to pinch

the cord, especially when mounting flush to

bottom of cabinet.

18

Installation Instructions

2

Rotate front of oven up

against cabinet bottom.

1

MOUNT THE OVEN

B6.

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from over

tightening screws.

NOTE: When mounting

the oven, thread power

cord through hole in

bottom of top cabinet.

Keep it tight throughout

Steps 1–3. Do not pinch

cord or lift oven by

pulling cord.

Lift oven, tilt it

forward and hook

slots at back bottom

edge onto two lower

tabs of mounting plate.

5

4

Cabinet Front

Cabinet Bottom Shelf

Tighten the three screws to the top of the oven

completely. (While tightening screws, hold the

oven in place against the wall and the top

cabinet.)

Filler Block

Oven Top

Equivalent

to Depth

of Cabinet

Recess

Install grease filters. See the Owner’s Manual

packed with the oven.

Self-Aligning Screw

3

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

C2.

19

RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

C1. Attach Mounting Plate to Wall

C2. Prepare Top Cabinet

C3. Adjust Blower

C4. Mount the Oven

C5. Install Charcoal Filter

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

Installation Instructions

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

C

Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall to

mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed flush

against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

4

3

ATTACH THE MOUNTING

PLATE TO THE WALL

C1.

Attach the plate to the wall using toggle bolts. At

least one wood screw must be used to attach the

plate to a wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate through

the holes designated to go into drywall and

reattach the toggle wings to

3

⁄4″ onto each bolt.

1

Wall

Mounting

Plate

Spacing for Toggles

More Than Wall

Thickness

Bolt End

Toggle

Bolt

Toggle Wings

To use toggle bolts:

2

AFTER: Fan Blade

Openings Facing

Forward

3

2

4

ADAPTING BLOWER

FOR RECIRCULATION

C3.

20

NOTE: The exhaust adaptor with damper is not

needed for recirculating models. You may want to

save them for possible future use.

Carefully pull out the blower unit. The wires

will extend far enough to allow you to adjust the

blower unit.

Roll the blower unit 90° so that fan blade openings

are facing toward the front of the oven.

Roll

Slide the blower plate from under its retaining

flange and lift it off.

Remove and save screws that hold blower plate and

blower unit to the oven.

Installation Instructions

BEFORE: Fan Blade

Openings Facing Up

1

Blower Plate

Retaining

Flange

Blower Plate

Back of Oven

Blower Plate Screws

Blower Motor Screw

Page is loading ...

GE 363.63672 User manual

GE 363.63672 User manual

in other languages

Related papers