Waeco CoolAir CA-EK-UNI3 Installation guide

Waeco
Brand
Waeco
Model
CoolAir CA-EK-UNI3
Type
Installation guide

This manual is also suitable for

Preconditions for installing the CoolAir CA-800
roof air conditioner with the
CA-800-Universal-3 mounting kit
WAECO International GmbH
Hollefeldstraße 63
D-48282 Emsdetten
www.waeco.com
Item
no.:
CA-EK-UNI3
CA-800 mounting kit for universal installation
(existing roof opening with standard fastening)
4445100310
Jun-07
Page 1 of 2
Many cab roofs have an identical fastening characteristic (hole pattern). The CA-EK-UNI3 mounting kit is for
installing a CA-800 one of these roof hatches. Note that the following conditions must be met before the roof air
conditioner can be installed:
• Check that your vehicle has the roof hatch shape shown in figs. 2 to 4.
• The available battery capacity to power the air conditioner must be at least
150 Ah.
• The available input voltage for the roof air conditioner must be between 20 V DC and
30 V DC.
• The CA-800 roof air conditioner is not suitable for installation in construction machines, agricultural machines
or similar equipment. It does not work properly in the event of strong vibrations.
• The roof of the cab must be designed to support the static weight and the loads of the air conditioner when the
vehicle is stationary and especially when it is in motion. Ask the manufacturer of your vehicle.
• The roof inclination of the mounting surface may not be more than 8° to the front and
0° to the rear.
• The vehicle height may not exceed 4 m with the roof air conditioner fitted.
• Installing the air conditioner may not
damage any components on the vehicle or
impair their function. Fig. 1 shows the
system dimensions when installed.
• The roof thickness may not be more than
85 mm or less than 25 mm.
401 mm
291 mm
Centre of roof
Roof thickness (distance between contact faces of seals and
cover frame
)
= max. 85 mm, min. 25 mm
Fig. 1
209 mm
Fig. 2
Fig. 3
12 mm
Seal contact
face
Ø 8.5 mm
Direction of travel
684 mm
543 mm
341 mm
482 mm
185 mm
Preconditions for installing the CoolAir CA-800
roof air conditioner with the
CA-800-Universal-3 mounting kit
WAECO International GmbH
Hollefeldstraße 63
D-48282 Emsdetten
www.waeco.com
Item
no.:
CA-EK-UNI3
CA-800 mounting kit for universal installation
(existing roof opening with standard fastening)
4445100310
Jun-07
Page 2 of 2
• The maximum dimensions shown in fig. 4
are also the outside dimensions of the
balance plate.
• The space between the required contact
face for the seal may be no more than 790
mm and no less than 730 mm wide, and no
more than 590 mm and no less than 525
mm long (see fig. 4).
• Screw the cover frame in the cab from
below under the air conditioner. This
requires a specified area of the cab roof to
be available (see fig. 5).
max. 790 mm
min. 730 mm
max. 590 mm
min. 525 mm
Fig. 4
281 mm
401 mm
Fig. 5
Centre of roof
Direction of travel
R130
Balance
plate
565 mm
  • Page 1 1
  • Page 2 2

Waeco CoolAir CA-EK-UNI3 Installation guide

Waeco
Brand
Waeco
Model
CoolAir CA-EK-UNI3
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents