Acnodes PM6200 User manual

Type
User manual
PM6200
20 1 600 x 1200 TFT LCD
Op e n F r a m e LCD M o n i to r
Wa l l / P a ne l / VESA M o un t Re a d y
Ind ustrial
Monitors
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please v isit Acnodes website at www.acnodes.com
14628 Central Ave. Chino, CA 91710 Tel: 909.597. 7588 Fax: 909.597.1939
© C opyright 2015 Acnodes C orp.
L eg al Inf orm ation
F irst Eng Iish printing, O ctober 2002
Information in this doc ument has been carefu IIy checked for accuracy; however, no guarantee is given to the correctness
of the contents. T he information in this docum ent is subject to change without notice. W e are not Iiab Ie for any injury or
Ioss that resu Its from the use of this equipm ent.
Safet y Inst ru ctions
Please read all of th ese in structio ns carefully before yo u use th e d evice. Save this m anual for futu re reference.
Unp Iug equipm ent before cIeaning. Dont use Iiquid or spray detergent; use a moist cIoth.
Keep equipm ent aw ay from excessive humidity and heat. PreferabIy, keep it in an air-conditioned envir onment with
temperatures not exceeding 40 º Ce Isius (104 º F ahrenheit).
When insta IIing, pIace the equipment on a sturdy, Ieve I surface to prevent it from accidenta IIy fa IIing and causing dam
age to other equipment or injur y to persons nearby.
When the equipment is in an open position, do not cover, b Iock or in any way obstruct the gap betw een it and the
pow er suppIy. Proper air convection is necessary to k eep it from overheating.
Arrange the equipm ent’s power cord in such a w ay that others w ont trip or fa II over it .
If you are using a pow er cord that didn’t ship with the equipment, ensure that it is rated for the vo Itage and cur rent
Iabe Ied on the equipments eIectric aI ratings IabeI. T he vo Itage rating on the cord shou Id be higher than the one Iisted
on the equipment’s ratings Iabe I.
Observ e a II precautions and w arnings attached to the equipment.
If you don’t intend on using the equipment for a Iong time, disconnect it from the power outIet to prevent being dam
aged by tr ansient over-voItage.
Keep a II Iiquids aw ay fr om the equipment to minimize the risk of accidenta I spiIIage. Liquid spiIIed on to the pow er
suppIy or on other hardware may cause damage, fire or e Iectrica I shock.
On Iy qua Iif ied service personne I shou Id open the chassis. O pening it yourseIf cou Id damage the equipm ent and inva Ii
date its warranty.
If any part of the equipment becomes damaged or stops functioning, have it c hecked by quaIified service personne I.
W hat the w arran ty d oes not co ver
Any product, on which the seriaI number has been defaced, modified or rem oved.
Damage, deterioration or ma Ifunction resu It ing from:
Accident, m isuse, neg Iect, f ire, water, Iightning, or other acts of nature, unauthorized product modification, or
faiIure to fo IIow instructions supp Iied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
RemovaI or ins taIIation of the product.
Causes externa I to the product, such as e Iectric power f Iuctuation or faiIure.
Use of supp Iies or parts not meeting our specifications.
Norma I wear and tear.
Any other causes which does not re Iate to a product defect.
RemovaI, insta IIation, and s et-up service charges.
Regulato ry Notices Federal Co mm un ications Com m ission (FCC)
T his equipment has been tested and found to comp Iy with the Iimits for a CIass B digita I device, pursuant to Part 15 of the
F CC ru Ies. These Iimits are designed to provide reasonabIe protection against harmfuI interference in a residentia I insta I-
Iation.
Any changes or modifications made to this equipment may void the users authority to operate this equipm ent. This
equipment generates, uses, and can radiate radio frequency energy and, if not instaIIed and used in accordance with the
instructions, m ay cause harmfuI interference to radio communications.
How ever, there is no guar antee that interference wiII not occur in a particu Iar instaIIation. I f this equipment does caus e
harmfu I interference to radio or te Ievis ion reception, which c an be deter mined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the fo IIowing m easures:
Re-pos ition or reIocate the receiving antenna.
Increase the separation between the equipm ent and receiver.
Connect the equipment into an outIet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > PM 6200
1.1
Package Content
1.2
Structure Diagram & Dimension
1.3
Mounting Hardware & InstaIIation
P.1
P.2 - 3
P.4
< Part. 2 > Specifications I OSD
2.1
Product Specifications
2.2
On-screen DispIay Operation ( OSD )
P.5
- 6
P.7
< Part. 3 >
Options
3.1
Option TabIe
3.2
3G / HD / SD-SDI Broadcast-grade input
3.3
MCS MuIti-dispIay controI soIution
3.4
AD2.2 Upgrade : HDMI, S-Video + BNC & Audio
3.5
AD3.0 Upgrade : HDMI, DVI-D, S-Video + BNC & Audio
3.6
20" Touchscreen : Resistive
3.7
48V, 24V or 12VDC power
3.8
MIL-type or IockabIe connector
3.9
Quad dispIay for CCTV
3.10
TV ( AnaIog )
P.8
P.9
P.10
P.11
P.12
P.13
P.14
P.15
P.16
P.17 - 18
Before Installation
It is very important to mount the equipment in a suitabIe cabinet or on a stabIe surface.
Make sure the pIace has a good ventiIation, is out of direct sunIight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
incIuded and in good condition. If anything is missing, or damaged, contact the suppIier immediateIy.
How To Clean Your LCD Monitor
Caution :
To avoid the r isk of eIectric shock, make sure your hands are dry before unpIugging your monitor from or
pIugging your monitor into an eIectricaI outIet.
When you cIean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your dispIay. Pressure damage is not covered under warranty.
Use onIy cIeansers made specificaIIy for cIeaning monitors and monitor screens. CIeansers not made to
cIean monitors and monitor screens can scratch the LCD dispIay or strip off the finish.
Do not spray any kind of Iiquid directIy onto the screen or case of your monitor. Spraying Iiquids directIy
onto the screen or case can cause damage which is not covered under warranty.
Do not use paper toweIs or abrasive pads to cIean your monitor. Using an abrasive pad or any wood based
paper product such as paper toweIs can scratch your LCD screen.
Cleaning Your Monitor
To cIean your LCD safeIy, pIease foIIow these steps :
1
Disconnect the power cord.
2
GentIy wipe the surface using a cIean, dry microfiber cIoth. Use as IittIe pressure as possibIe.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, pIease foIIow these steps :
1
Disconnect the power cord.
2
Spray a smaII amount of non-abrasive cIeanser on a microfiber cIoth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
GentIy wipe the surface. Use as IittIe pressure as possibIe.
4
Wait untiI your monitor is compIeteIy dry before pIugging it in and powering it up.
< Part 1 >
< 1.1 > Package Content - PM 6200
PM 6200
20" LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
Standard IIO
AD2.2 upgrade IIO
AD3.0 upgrade IIO with advanced features
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudj DCDi Cinema processing
- Casing dimensions will be changed
out - in - in
Video PC
V GA
DVI- D
Audio
Power BNC S-Video
out - in - in
Video PC
HDMI
V GA
Audio
Power BNC S-Video
Power DVI- D
VGA
3
6
1
2
4
5
< 1.2 > Structure Diagram -PM6200
20" LCD Display
Front view
1 Rear case
2 LCD paneI
3 Audio speaker ( for HDMI, Audio or TV option )
4 UniversaI open frame mounting
5 LCD membrane
6 Extended remote sensor membrane cabIe
( 66cm from AD board to sensor end )
Rear view
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
PM6200
510 x 66 x 389 mm
20.1 x 2.6 x 15.3 inch
651 x 124 x 597 mm
25.6 x 4.9 x 23.5 inch
6 kg
13.2 Ibs
8 kg
17.6 Ibs
< 1 .2 > D im ens io n - PM 62 00
F ro n t View S id e View
R ear V ie w
UN IT : m m
1 m m = 0 .03937 inch
B o tt o m V iew
< 1.3 > Installation - PM 6200
20” LCD Display
( I ) Universal mount
( II ) VESA mount ( 100*100mm )
M4 screw
Hardware and M4*4 pcs for VESA mounting are not provided
< Part 2 >
< 2.1 > Product Specifications
Mecha nical
Design
PM 6200
Front PaneI
-
Rear Casing
Dark grey, RAL 7037
VESA Mounting
100 x 100mm
Other Mounting
UniversaI mount
Protection
-
LCD
Panel
Manufacturer
PaneI Size ( diagonaI )
20-inch TFT coIor LCD
DispIay pixeI ( dots x Iines )
1600 x 1200
Brightness ( typ. )
300
Contrast Ratio ( typ. )
800:1
CoIor
16.7 M
Viewing AngIe ( L/R/U/D )
89/89/89/89
Response Time ( ms )
16
Dot pitch ( mm )
0.255
DispIay Area ( mm )
408.00H x 306.00V
Surface treatment
Anti-gIare, Hard-coating
Surface hardness
3H
BackIight Type
CCFL
MTBF ( hrs )
45,000
Video
Connec tivity
AnaIog
VGA
AnaIog 0.7Vp- p
DVI-D
DVI- D, TMDS singIe Iink
Power
Power SuppIy
Range
Auto-sensing 100 to 240VAC,
50/60Hz
Power Consumption
Screen dispIay ON
48W or Iess
Power saving mode
4W or Iess
Power button OFF
1W or Iess
Regulatory
Safety ApprovaI
FCC & CE
Environmental
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceIeration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
510 x 66 x 389 mm
20.1 x 2.6 x 15.3 inch
Packing ( W x D x H )
651 x 124 x 597 mm
25.6 x 4.9 x 23.5 inch
Net Weight
6 kgs / 13.2 Ibs
Gross Weight
8 kgs / 17.6 Ibs
Applicable
Format
VGA Input
PC SignaI
1600 x 1200 x 60Hz
1400 x 1050 x 60Hz
1440 x 900 x 60Hz
1360 x 768 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< 2.2 > On-screen Display Operation ( OSD )
Power Iight
Green = On
Orange = Power saving
Membrane Switch Function
Power on / off LCD
DispIay the OSD menu
ScroIIs through menu options and adjusts the dispIayed controI
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
ToggIe anaIog, digitaI & video connection (DVI-D and video options onIy)
OSD Configuration Page
Image:
for the brightness, contrast, coIor temp, red, green, and bIue
Geometry:
for the auto adjust, H position, V position, phase and cIock
Video:
for the coIour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for voIume, bass, trebIe, baIance, AVL and mute
Misc:
for the Ianguage, OSD position, graphic mode, ratio, reset and timer
< Part 3 > Options
20” LCD Display
< 3.1 > Option Table
Options
APM
PM
SDI ***
HDMI * or DVI-D
S-Video * + Composite ( BNC )
Audio
Touc hscreen
MCS muIti-dispIay controI ***
DC Power
MIL-type / IockabIe connector
Quad dispIay
TV ( AnaIog ) *
***
About SDI and MCS
( 1 ) The user can only select either SDI or MCS inputs.
( 2 ) For SDI input, the AD board will be upgraded to version 3.0, and this comes standard
with HDMI, DVI-D, VGA, S-Video, BNC, audio inputs and RC-2 remote controller.
*
About HDMI and DVI-D
( 1 ) For AD2.2 upgrade, only HDMI is provided.
( 2 ) If the user needs HDMI and DVI-D, AD3.0 upgrade can be applied.
*
Remote Controller
( 1 ) AD2.2 upgrade comes with RC-1 remote controller.
( 2 ) AD3.0 upgrade or TV option comes with RC-2 remote controller.
< 3.2 > Options : 3G I HD I SD-SDI input
Acnodes SDI input is an ideaI soIution for the broadcast- grade
video and high resoIution CCTV market.
Designed for use with FuII HD 1080p and uItra high resoIution
1920 x 1200 LCD dispIays, Acnodes provides a SDI input
moduIe without using additionaI space or power and it com es
standard with a 2- year warranty.
Power BNC S-Video
Audio
out - in - in
Video PC
HDMI
DVI-D VGA
SDI
out - in
*** For SDI option, the AD board wiII be upgraded to AD3.0, and this com es standard with HDMI, DVI-D,
VGA, S-Video, BNC, audio inputs and RC-2 rem ote controIIer ( pIease refer to P.23 )
INPUT
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equaIized & reIocked
Standard Compliance
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
Compatible Video Format
3G-SDI
1080p
@60 / 50Hz, 4:2:2
1080p
@30 / 25 / 24Hz, 4:4:4
1080i
@60 / 50Hz, 4:4:4
720p
@60 / 50Hz, 4:4:4
HD-SDI
1080p
@30 / 25 / 24Hz, 4:2:2
1080i
@60 / 50Hz, 4:2:2
720p
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
Compatible Audio Format
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Async hronized Video
Max. Transmission Distance
75 ohm coaxial cable
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s
< 3.3 > Options : MCS
MCS
( Multi-display Control )
More controI is aIways good. EspeciaIIy when it is necessary and
easy. Acnodes provides MCS soIution to controI the OSD of
various LCD dispIay up to 64 units.
The RS- 232C is used for the communication between the PC and
the first dispIay via a 15 feet seriaI cabIe whiIe the CAN bus is
used for the various LCD dispIays cascade together via CAT 5/6
cabIe, and daisy chain up to 1,000 meters.
Designed for use with various LCD dispIays, Acnodes provides
a MCS input moduIe without using additionaI space or power
and it comes standard with a 2-year warranty.
MCS
Set switch
RS-232C
For the 1st and Iast dispIay,
push the set switch upward
15 feet seriaI cabIe
( over 15 feet, extender required )
For other daisy chain dispIays,
push the set switch downward
LINK OUT IN OUT IN OUT IN
OUT
RJ-45 jack
Cat5 / 6 cabIe
max. 300 meters
Cat5 / 6 cabIe
max. 300 meters
Daisy chain up to 1,000
meters and 64 dispIays
Cat5 / 6 cabIe
max. 300 meters
up to 64 dispIays
Link
out - in - in
Video PC
HDMI
VGA
DVI-D
Audio
Power BNC S-Video
< 3.4 > AD2.2 Upgrade Options :
- HDMI
- S-Video + BNC
- Audio
AV
HDMI
Audio
***
: S-Video + Composite (BNC)
: HDMI 1.1, CEA-861-D
: 3.5mm audio jacks for audio in & out, and 2W + 2W speakers
AD2.2 upgrade option comes with RC-1 remote controller x 1.
5
1
2
3 6
7
4
8
9
1
POWER Switches on or off the TV
2
MUTE Turn on or off the speaker
3
AV Switch to AV mode
4
0- 9
SeIect channeIs. For channeI numbers 10 and above,
enter the second digit within two seconds.
5
V + I - Increase or decrease the speaker voIume
6
CH + I - Increase or decrease the channeI number
7
MENU DispIay the menu on the screen or go to the previous menu
8
AUTO For auto searching
9
- I - For setting one or two input digit
out - in - in
Video PC
HDMI
VGA
Audio
Power BNC S-Video
< 3.5 > AD3.0 Upgrade Options :
- HDMI
- DVI-D
- S-Video + BNC
- Audio
20” LCD Display
Power BNC S-Video
Audio
out - in -
i n
Video PC
HDMI
DVI-D VGA
AV
HDMI
DVI-D
Audio
: S-Video + Composite (BNC)
: HDMI 1.1, CEA-861-D
: DVI-D TMDS singIe Iink
: 3.5mm audio jacks for audio in & out, and 2W + 2W speakers
***
( 1 ) AD3.0 upgrade option comes with RC-2 remote controller x 1, please refer to P.23
( 2 ) Casing dimensions will be changed
< 3.6 > Options : Touchscreen & driver
20" USB Touchscreen Specification
Model
TRB
e-Resistive
Technology
5-Wire Resistive
Touch Point
SingIe
Method
StyIus or Finger
Activation Force
= 50g / StyIus=R0.8
Durability
35 miIIion touches
Response Time
15 ms
Optical Transmittance
80% ± 3%
Surface Hardness
3H
Haze
8% ± 3%
Glass
3.2 ±0.2 mm
Connector
USB Type A
Compatibility
Windows 7 / XP / Vista, Linux
USB touchscreen package incIudes 1 x 6ft USB cabIe, quick reference guideIine and CD disc
For detaiIed information, pIease refer to the attached CD disc
As the touchscreen unit is not made of toughened gIass, pIease handIe it carefuIIy
USB Touchscreen
Power VGA
Please follow the below steps to setup the touch screen:-
Step 1. Run the bundIed CD disc
Step 2. DoubIe cIick the Setup.exe
Step 3. FoIIow the instaIIation instruction to finish the setup
Step 4. After instaIIation, run the TouchKit program & the “4 point caIibration”
PIease do the initiaI caIibration
after the first setup
< 3.7 > Options : DC Power
Model
12V
24V
48V
Input rating
Input voItage:
12-VoIt
24-VoIt
48-VoIt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
Input current
- No Ioad
50 mA
50 mA
50 mA
- FuII Ioad
4950 mA
2450 m A
1220 mA
Output rating
Output voItage:
12-VoIt
12-VoIt
12-VoIt
Output current:
4.16A
4.16A
4.16A
Efficiency
84%
85%
85%
< 3.8 > Options : MIL-type or Lockable Connector
Input
Part no.
MIL Standard
MIL - type
Connector
DC Power ***
( MaIe )
MS3470W8-33P
MIL - DTL - 26482
VGA ***
( MaIe )
MS3470W14-15P
MIL - DTL - 26482
*** There are severaI additionaI MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design fIexibiIity possibIe. For more information, pIease contact us.
Input
Part no.
Standard
Lockable
Connector
DC Power
( MaIe )
YM-Ext-461CP001
D-type 3W3
USB
LUSB - A111 - 00
-
*** MIL - type or LockabIe connectors above can be integrated with our LCD dispIays.
SaIe service just for connectors not provided.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Acnodes PM6200 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI