1
Camera PCD3100
Quick Guide
Version 1.0
(English)
2
FCC GUIDELINES
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
The Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulation.
Cet appareil numerique de la class B respecte toutes les exigences du Règlement sur le materiel
brouilleur du Canada.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference. (2) This device must accept any
interference received, including interference that may cause undesired operation.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment. Shielded interface cable, if any, must
be used in order to comply with emission limits.
The information in this document is subject to change without notice and does not represent a
commitment on the part of the vendor.
No warranty of representation, either expressed or implied, is made with respect to the quality,
accuracy or fitness for any particular purpose of this document. The manufacturer reserves the
right to make changes to the content of this document and/or the products associated with it at
any time without obligation to notify any person or organisation of such changes.
In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising out of the use or inability to use this product or documentation, even if advised of
the possibility of such damages.
Copyright
©
2003. All rights reserved
IBM, PC/AT and PS/2 are registered trademarks of International Business Machines Corporation.
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the
United States of America and/or other countries.
All other trademarks are trademarks off their respective holders.
封面內頁
3
English
Congratulations on purchasing your new digital & PC camera (Optional).
This camera is an all-in-one pocket size digital and USB PC camera. You
can take digital pictures at once. Alternatively you can also hang up the
camera to a computer and use it as a PC camera for videoconferencing or
capturing video clips.
Getting to Know the Camera- PCD3100
Flash light indicator
Viewfinder Microphone
Speaker
Display panel
Mode button
Stand Receptacle
4
System Requirements
! MicrosoftWindows98, WindowsME, Windows2000 or
WindowsXP operating system
Software Installation
Please note that you have to install the software BEFORE you connect the
camera into the USB port of your computer.
Step 1: Install Ulead Photo Express 4.0 SE
1. Insert the software CD into the CD-ROM drive of your computer.
2. Follow the on screen instruction to install the software. The software
will install automatically.
! Note: If the software does not setup automatically, go to the Taskbar
and click Start, then click on Run and browse the SETUP.EXE in the
software CD and click OK to install.
When all setup procedures are finished, the operating system does not
need to restart. The software is loaded when you see the software icon
shows on the screen.
! Important: For more information on how to use the software,
please refer to the folder named “Manual” in the CD.
Step 2: Install Digital Camera Driver-CamMaestro
1. In order to take great advantage of the camera, please note that you
have to install the driver named “CamMaestro” AFTER
you have
installed the camera application software in step 1.
2. Follow the on screen instruction to install the software. The software
will install automatically.
! Note: If the software does not setup automatically, go to the Taskbar
and click Start, then click on Run and browse the
SETUP.EXE in the
\Driver directory of the software CD and click OK to install.
When all setup procedures are finished, the operating system needs to
restart.
5
English
Uninstallation
To Remove Camera Application Software:
1. Click "Start" menu (on the left-bottom taskbar).
2. Move cursor to "Programs" in "Start" menu and select “Control Panel”.
3. Click on “Add/Remove Programs” in the Control Panel.
4. Select “Ulead Photo Express 4.0 SE” and click on the remove icon.
5. Click "Yes" to confirm you want to uninstall.
To Remove Camera Driver:
1. Click "Start" menu (on the left-bottom taskbar).
2. Move cursor to "Programs" in “Start” menu and select “Control Panel”.
3. Click on “Add/Remove Programs” in the Control Panel.
4. Select “CamMaestro” and click on the remove icon.
5. Click "Yes" to confirm you want to uninstall.
Getting Start
Insert or Change the Battery
Slide the compartment cover open and change the 2 pcs of AAA alkaline
batteries. After inserting the batteries, you can immediately take the great
advantage of the camera.
Connect to PC
If you want the digital camera works as a PC camera, you just simply have
to use the USB connection cable that enclosed in the package to connect
the camera to you PC.
Make sure to power OFF the camera
before you change the batteries.
6
Camera Buttons
Mode Button
Press on the mode button to switch through High
resolution or Low-resolution mode.
Snapshot Press Snapshot button once to take one image.
How to Take Pictures
Change modes
Press on the mode button to cycle through High
resolution or Low-resolution mode.
Take snapshots
Press Snapshot button once to take a shot. Press
and hold Snapshot button to take video stream
movie shots.
Camera Display Panel
Here is the list of all the icons that appear on the Camera Display Panel and
functions.
26 Image number for VGA.
OF Power on or power off status.
Ct
Continuous shot. You can take a series pictures on VGA
mode by pressing on the snapshot button.
AI
Video recording, AVI file. You can use this function to take a
video by holding the snapshot button.
St Self-shot.
CL Delete the last image.
CA Delete all pictures in the camera memory.
Lr/Hr
Low resolution or high resolution, QVGA and VGA.
For Low-resolution mode, you can take pictures for 104
images. (Max.)
For High resolution, you can take 26 images.
CP/nP Compression mode and non-compression mode.
F5/F6 50Hz and 60Hz
Lo
Battery Low. Please download your pictures in memory first
and then change the batteries as soon as possible.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
28
3100560180
Version 1.0
July 2003
Printed in China
/