ZANKER ZKF680ITXB User manual

Page is loading ...

2

Important Safety Information..........................................................................................................................3

Hob burner control knobs...............................................................................................................................5

Using the hob.................................................................................................................................................7

Cleaning and Maintenance ............................................................................................................................8

Technical data ..............................................................................................................................................10

Installation.................................................................................................................................................... 11

Adaptation to different types of gas..............................................................................................................12

Electrical Connection ...................................................................................................................................13

Building In ....................................................................................................................................................15

Possibilities for insertion...............................................................................................................................17

Technical assistance and spare parts .......................................................................................................... 18

Declaration of guarantee terms....................................................................................................................19

European Guarantee ...................................................................................................................................21

Contents

The following symbols will be found in the text to guide you throughout the Instructions:

Safety Instructions

Step by step instructions for an operation

Hints and Tips

Environmental information

Guide to Use the instructions

This appliance complies with the following E.E.C. Directives:

• 2006/95 (Low Voltage Directive);

• 89/336 (Electromagnetical Compatibility Directive);

• 90/396 (Gas Appliances);

• 93/68 (General Directives) and subsequent modifications.

It is very important that this instruction book should be kept safely for future consultation. If the appliance should

be sold or given to another person, please ensure that the booklet goes together with it, so that the new owner can

know of the functions of the machine and also be aware of the warnings.

These instructions are only for the countries stated by the symbol printed on the front cover of this instruction book.

)

MANUFACTURER:

ELECTROLUX HOME PRODUCTS ITALY S.p.A.

Viale Bologna, 298

47100 FORL

Ì (Italy)

3

Installation

z The work of installation must be carried out by

competent and qualified installers according to the

regulations in force.

• Any modifications to the domestic electrical

mains which may be necessary for the

installation of the appliance should be carried

out only by competent personnel.

During Operation

• This appliance has been designed for non

professional purpose in private houses only. It is

meant to cook edible foodstuff only and must not

be used for any other purposes.

• It is dangerous to alter the specification in any

way.

• For hygiene and safety reasons, this appliance

should be kept clean at all times. A build-up of

fats or other foodstuff could result in a fire.

• Under no circumstances should you attempt to

repair the appliance yourself. Repairs carried out

by unexperienced persons may cause injury or

serious malfunctioning. Refer to your local

Service Centre. Always insist on genuine spare

parts.

• Ensure that all control knobs are in the OFF

position when not in use.

• Should you connect any electrical tool to a plug

near this cooking appliance, ensure that electric

cables are not in contact with it and keep them far

enough from the heated parts of this appliance.

• If the appliance is out of order, disconnect it from

the electric supply.

People Safety

• This appliance has been designed to be

operated by adults and children under

supervision. Young children must not be allowed

English

This warnings has been given for the safety of you and others. We therefore ask you to carefully read the

procedures of installing and using this cooker.

Important safety information

to tamper with the controls or play near or with the

oven.

• This appliance is not intended for use by children

or other persons whose physical, sensory or

mental capabilities or lack of experience and

knowledge prevents them from using the

appliance safely without supervision or

instruction by a responsible person to ensure that

they can use the appliance safely.

• Accessible parts of this appliance may become

hot when it is in use. Children should be kept

away until it has cooled.

About Installation, Cleaning and Maintenance

• It is mandatory that all operations required for the

installation are carried out by a qualified or

competent person, in accordance with existing

rules and regulations.

• Disconnect the appliance from the electrical

supply, before carrying out any cleaning or

manteinance work.

• Ensure a good ventilation around the appliance.

A poor air supply could cause lack of oxygen.

• Ensure that the gas supply complies with the gas

type stated on the identification label, placed near

the gas supply pipe.

• This appliance is not connected to a combustion

products evacuation device. It must be installed

and connected in accordance with current

installation regulations. Particular attention shall

be given to the relevant requirements regarding

ventilation.

• The use of a gas cooking appliance results in

the production of heat and moisture in the

room in which it is installed. Ensure that the

kitchen is well ventilated: keep natural

ventilation holes open or install a mechanical

ventilation device (mechanical extractor

hood).

4

• Prolonged intensive use of the appliance may

call for additional ventilation, for example

opening of a window, or more effective

ventilation, for example increasing the level

of mechanical ventilation where present.

• Once you removed all packaging from the

appliance, ensure that it is not damaged and the

electric cable is in perfect conditions. Otherwise,

contact your dealer before proceeding with the

installation.

• The manufacturer disclaims any

responsability should all the safety measures

not be carried out.

Service

• Under no circumstances should you attempt to

repair the appliance yourself. Repairs carried out

by unexperienced persons may cause injury or

serious malfunctioning. Refer to your local Service

Centre. Always insist on genuine spare parts.

Environmental Information

• After installation, please dispose of the

packaging with due regard to safety and the

environment.

• When disposing of an old appliance, make it

unusable, by cutting off the cable.

The symbol on the product or

on its packaging indicates that this product may not

be treated as household waste. Instead it shall be

handed over to the applicable collection point for the

recycling of electrical and electronic equipment. By

ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the

environment and human health, which could

otherwise be caused by inappropriate waste handling

of this product. For more detailed information about

recycling of this product, please contact your local city

office, your household waste disposal service or the

shop where you purchased the product.

5

Hob burner control knobs

The symbols on the knobs mean:

= no gas supply

= maximum gas supply

= minimum gas supply

For easier lighting, proceed before putting a

pan on the pan support.

Lighting the burners

To light a burner, turn the relevant knob

anticlockwise to maximum position and push down

the knob to ignite.

After lighting the flame, keep the knob pushed down

for about 5 seconds. This will allow the

"thermocouple" (Fig.1 - lett. D) to be heated and the

safety device to be switched off, otherwise the gas

supply would be interrupted. Then, check the flame

is regular and adjust it as required.

If you cannot light the flame even after several attempts,

check the "cap" (Fig.1 - lett. A) and the"crown" (Fig.1

- lett. B) are in the correct position.

In the absence of electricity, ignition can occur without

the electrical device; in this case approach the burner

with a flame, push the relevant knob down and turn it

anti-clockwise until it reaches the "maximum" position.

To switch off burners

To put the flame out, turn the knob to the

symbol (

z).

)

Fig. 1

A

B

D

C

Triple crown

Once the hob has been installed, it is

important to remove any protective

materials, which were put on in the

factory. The manufacturer will not accept

liability, should the above instructions or

any of the other safety instructions

incorporated in this book be ignored.

A - Burner cap

B - Burner crown

C - Ignition candle

D - Thermocouple

6

Take care when frying food in hot oil or fat,

as the overheated splashes could easily

ignite.

When switching on the mains, after installation

or a power cut, it is quite normal for the spark

generator to be activated automatically.

If the burner does not ignite, turn the control

knob to zero, and try again.

Do not keep the control knob pressed for

more than 15 seconds. If the burner does not

light even after 15 seconds, release the control

knob, turn it the “off” position and wait for at

least one minute before trying to light the

burner again.

If the burner accidentally goes out, turn the

control knob to the “off” position and wait

for at least 1 minute before trying to light the

burner again.

7

Using the hob correctly

To ensure maximum burner efficiency, you should

only use pots and pans with a flat bottom fitting the

size of the burner used (see table below).

• For easier lighting, proceed before putting a pan on

the pan support.

• Use only pans or pots with flat bottom.

• Take care when frying food in hot oil or fat, as

the overheated splashes could easily ignite.

• If you use a saucepan which is smaller than the

recommended size, the flame will spread beyond

the bottom of the vessel, causing the handle to

overheat.

• Prolonged cooking with potstones,

earthenware pans or cast-iron plates is

inadvisable. Also, do not use aluminium foil to

protect the top during use.

• Make sure pots do not protrude over the edges of

the cooktop and that they are centrally positioned

on the rings in order to obtain lower gas

consumption.

• Do not place unstable or deformed pots on the

rings: they could tip over or spill their contents,

causing accidents.

• Pots must not enter the control zone.

• If the control knobs become difficult to turn, please

contact your local Service Force Centre.

• As soon as a liquid starts boiling, turn down the

flame so that it will barely keep the liquid

simmering.

Burner Minimum Maximum

diameter diameter

Triple crown burner 180 mm 260 mm

Semirapid burner

rear 120 mm 220 mm

front 120 mm 180 mm

Auxiliary burner 80 mm 160 mm

8

Cleaning and Mainteinance

Disconnect the appliance from the elec-

trical supply, before carrying out any

cleaning or manteinance work.

The hob is best cleaned whilst it is still

warm, as spillage can be removed more

easily than if it is left to cool.

This appliance cannot be cleaned with

steam or with a steam cleaning machine.

The burners

z The burner caps and crowns can be removed

for cleaning.

z Wash the burners taps and crowns using hot

soapy water, and remove marks with a mild

paste cleaner. A well moistened soap

impregnated steel wool pad can be used with

caution, if the marks are particularly difficult to

remove.

z After cleaning, be sure to wipe dry with a soft

cloth.

z Frequently wash the "caps" and the "crowns" with

hot soapy water, carefully taking away any built-up

of food.

The pan supports

z The enamelled grills can be cleaned with warm

soapy water.

Take care when drying them as the enamelling

process occasionally leaves rough edges. If

necessay, remove stubborn stains using a

paste cleaner.

z After cleaning, make sure that the pan supports

are correctly positioned.

z To make burners work properly, ensure that pan

supports are placed in a way that the arms are

centred upon the burner as shown in the picture.

z Pay attention when replacing the pan sup-

ports in order to avoid damaging the hob

top.

NO

YES

9

The Hob Top

z Regularly wipe over the hob top using a soft

cloth well wrung out in warm water to which a

little wasing up liquid has been added. Avoid the

use of the following:

- household detergent and bleaches;

- impregnated pads unsuitable for non-stick

saucepans;

- steel wool pads;

- bath/sink stain removers.

z Do not leave acid or alkaline substances

(e.g. vinegar, salt, lemon juice, etc.) on the

cooktop.

The Ignition electrode

The electric ignition is obtained through a

ceramic electrode with a metal electrode inside

(Fig.1 - C). Keep these components very clean, to

avoid difficult lighting, and check that the burner

crown holes (Fig.1 - B) are not obstructed.

10

Cut out dimensions

(see chapter “Building In”)

Width: 560 mm

Depth: 480 mm

Overall dimensions

Width: 594 mm

Depth: 510 mm

Technical data

Heat Input

Triple Crown burner 4,0 kW

Semi-rapid burner 2,0 kW

Auxiliary burner 1,0 kW

Electric supply: 230 V ~ 50 Hz

Category: II2E+3+

Gas supply: G20/G25 (2E+) 20/25 mbar

Appliance class 3

Burner Normal rEDUCED nORMAL pOWER

POWER POWER

kW kW NATURALPOWER LPG

28-30/37 mbar

m3/h g/h

inj.

G20 G25

inj.

G30 G31

100/mm 20 mbar 25 mbar 100/mm

Auxiliary 1,0 0,33 70 0,095 0,111 50 73 71

Semi-rapid 2,0 0,45 96 0,190 0,221 71 145 143

Triple crown 4,0 1,2 146 0,381 0,443 98 291 286

By-pass diameters

Burner Ø By-pass in 1/100 mm.

Auxiliary 28

Semi-rapid 32

Triple crown 56

11

Installation

z The following instructions about installation

and maintenance must be carried out by

qualified personnel in compliance with the

regulation in force. The regulation to be

applied for this type of installation is NBN D

5I.003 : "Installations functioning with com-

bustible gas lighter than air".

z The side walls of the unit in which the hob is

going to be installed, must not exceed the

height of the working top.

z Avoid installing the appliance in the

proximity of inflammable materials (e.g.

curtains, tea towels etc.).

z The appliance must be electrically

disconnected before all interventions. If any

electric supply to the appliance is required

to carry out the work, ensure all the

necessary precautions are followed.

Gas Connection

It is indispensible that the connection to the gas mains

are carried out by means of an AGB tap. Choose fixed

connections or use a flexible pipe in AGB (stainless

steel).

If using flexible metallic pipes, be careful they do not

come in contact with mobile parts or they are not

squeezed. Use the same attention when the hob is

combinated with an oven.

This hob can be operated by Slochteren gas (G25)

with a nominal pressure of 25 mbar or by natural gas

with nominal pressure of 20 mbar. No regulation is

required for use by these two types of gas. Before

fitting the appliance ensure that the installation has

the correct voltage for the appliance. At full capacity,

the drop in pressure must not exceed 5%. Such a

drop in pressure is caused by the following

parameters:

- maximum capacity of meter;

- diameter and lenght of the tube in front and

behind the meter;

- section of transit of variuos tubes positioned

on the circuit;

- diameter of eventual connections.

To ensure a correct operation, a saving of energy and

the long-life of the appliance, the voltage pressure of

the appliance must correspond to the recommended

values.

The adjustable connection is fixed to the

comprehensive ramp by means of a threaded nut G 1/

2". All the components shown in the figure have

already been assembled in the factory.

The appliance, before leaving the factory, has been

tested in order to give you the best results.

Important

When the final connection has been made, it is

essential that a thorough leak test is carried out on the

hob and installation. Use some soapy water, never a

flame.

A - Ramp with ending nut

B - Seal

C - Adjustable connection

12

Adaptation to different types of gas

Injectors replacement

• Remove the pan supports.

• Remove the burner's caps and crowns.

• With a socket spanner 7 unscrew and remove

the injectors (Fig. 2), and replace them with the

ones required for the type of gas in use.

• Reassemble the parts, following the same

procedure backwards.

• Replace the rating label (placed near the gas

supply pipe) with the relevant one for the new

type of gas supply. You can find this label in the

package of the injectors supplied with the

appliance.

Should the feeding gas pressure be different or va-

riable compared with the required pressure, an

appropriate pressure adjuster must be fitted on the

gas supply pipe, in compliance with the rules in

force.

Adjustment of minimum level

To adjust the minimum level of the burners, proceed

as follows:

• Light the burner.

• Turn the knob on the minimum position.

• Remove the knob.

• With a thin screwdriver, adjust the by-pass

screw (Fig. 3). If changing from natural gas to

LPG, completely tighten clockwise the screw,

until a small regular flame is obtained.

• If changing from LPG to natural gas unscrew

about 1/4 turn the by-pass screw, until a small

regular flame is obtained.

• Finally check the flame does not go out when

quickly turning the knob from the maximum po-

sition to the minimum position.

This procedure can easily be carried out, anyhow

the hob has been positioned or built in the working

top.

Fig. 2

)

Bypass-screw

Fig. 3

13

The appliance is designed to be connected to

230 V monophase electricity supply.

The connection must be carried out in

compliance with the laws and regulations in force.

Before the appliance is connected:

1. check that the main fuse and the domestic

installation can support the load (see the rating

label);

2. check that the power supply is properly earthed in

compliance with the current rules;

3. check the socket or the double pole switch used

for the electrical connection can be easily

reached with the appliance built in the forniture

unit.

The appliance is supplied with a connection cable and

the relevant plug.

The plug has to be fitted in a proper socket.

If connecting the appliance directly to the electric

system, it is necessary that you install a double pole

switch between the appliance and the electricity supply,

with a minimum gap of 3 mm. between the switch

contacts and of a type suitable for the required load in

compliance with the current rules.

The connection cable has to be placed in order that, in

each part, it cannot reach a temperature higher than

90°C.

The brown coloured phase cable (fitted in the

terminal block contact marked with "L") must always

be connected to the network phase.

Electrical connection

14

Remplacement of the voltage cable

The connection of the voltage cable to the

appliance's terminal block is of type "Y". This means

that its replacement requires the specific equipment

of a technician. In this case, only cable type

H05V2V2-F T90 must be used. The cable section

must be suitable to the voltage and the working

temperature. The yellow/green earth wire must be

approximately 2 cm. longer than the phase wires (Fig.

4-a).

To open the terminal block and reach the

terminals, proceed as follows:

z insert the point of a screwdriver into the visible

protrunding part of the terminal block;

z exert a light pressure and lift (Fig. 4-b)

Fig. 4-b

Earth

(yellow/green))

Neutral

Fig. 4-a

15

Building In

These hobs can be inserted in a built-in kitchen unit

whose depth is between 550 and 600 mm. The hobs

dimensions are shown in Fig. 5.

The cut out dimensions are shown in Fig. 6.

The edge of the cut out must have a minimum dis-

tance from the rear wall of 55 mm.

If there are side walls, or sides of the furniture unit

near the hob, the cut out edges must have a mini-

mum distance of 100 mm.

Hanging forniture units or hoods must be placed at

650 mm. minimum from the hob.

A = Auxiliary burner

SR = Semi-rapid burner

TC = Triple Crown burner

Fig. 6

Dimensions are given in millimeters

510

594

TC

SR

A

SR

Fig. 5

16

Fig. 7

Fig.8

a

a) seal

Fitting the hob to the worktop

Carry out the building in of the hob as follows:

1. Place the seals supplied with the hob on the

front edge of the cut out. Then, place them at 11

mm from the side edges and at 10 mm from the

rear edge, as shown in the diagram, taking care

that the seals meet without overlapping.

2. Place the hob in the cut out, taking care that it is

centred.

3. Fix the hob with the relevant fixing clamps,

supplied with the injectors kit (see diagram).

When the fixing brackets have been tightened,

the excess seal can be removed.

The overlaying sealing material should be

removed using a wooden or plastic knife in order

to avoid damaging the worktop.

To completely remove the sealing material

please position the plastic knife at an angle

(Position at an angle of 45°C).

The edge of the hob forms a double seal which

prevents the ingress of liquids.

17

Possibilities for insertion

Kitchen unit with door

Proper arrangements must be taken in designing the

forniture unit, in order to avoid any contact with the

bottom of the hob which can be heated when it is

operated. The recommended solution is shown in

Fig. 9. The panel fitted under the hob should be

easily removable to allow an easy access if a

technical assistance intervention is needed.

Kitchen unit with oven

The hob recess dimensions must comply the indica-

tion given in Figs. 10 and 11 and must be provided

with brackets to allow a continuous supply of air.

The hob's electric connection and the oven's one

must be carried out separately, both for safety

reasons and to allow the oven to be easily taken off

the unit.

Wall units or extractor hoods must be at least 650 mm

from the cooktop (Fig. 6).

a) Removable panel

b) Space for connections

Fig. 9

Fig. 10

Fig. 11

18

Before leaving the factory this appliance was tested

and verified by specialized personnel, in order to

ensure best performance. Any repairs or intervention

which may become necessary, must be carried out

with utmost care and attention.

For this reason, this hob should only be repaired or

serviced by an authorised Service Engineer and only

genuine approved spare parts should be used.

For Assistance, please contact your dealer or an

authorized Service Centre, specifying the type of

problem, the appliance model (Mod.), the product

number (Prod. No.) and the serial number (Ser. No.).

This information is given on the dataplate which is

supplied in the accessories plastic bag.

Technical assistance and spare parts

19

Declaration of guarantee terms

Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer ser-

vices department will repair this upon request, either during or after the guarantee period. The service life of the

appliance will not, however, be reduced as a result.

This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of

the Civil Code. The statutory rights that the consumer has under this legislation are not affected by this declaration

of guarantee terms.

This declaration does not affect the vendor’s statutory warranty to the end user. The appliance is guaranteed

within the context of and in adherence with the following terms:

1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free of charge any defect

that occurs within 24 months from the date the appliance is delivered to the first end user.

These guarantee terms do not apply in the event of use for professional or equivalent purposes.

2. Performing the guarantee means that the appliance is returned to the condition it was in before the defect

occurred. Defective parts are replaced or repaired. Parts replaced free of charge become our property.

3. So as to avoid more severe damage, the defect must be brought to our attention immediately.

4. Applying the guarantee is subject to the consumer providing proof of purchase showing the purchase

and/or delivery date.

5. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic),

synthetic materials and rubber, is the result of inappropriate use.

6. The guarantee cannot be called on for minor faults that do not affect the value or the overall reliability of

the appliance.

7. The statutory warranty does not apply when defects are caused by:

- a chemical or electrochemical reaction caused by water,

- abnormal environmental conditions in general,

- unsuitable operating conditions,

- contact with harsh substances.

8. The guarantee does not apply to defects due to transport which have occurred outside of our

responsibility. Nor will the guarantee cover those caused by inadequate installation or assembly, lack of

maintenance or failure to respect the assembly instructions or directions for use.

9. Defects that result from repairs or measures carried out by people who are not qualified or expert or

defects that result from the addition of non-original accessories or spare parts are not covered by the

guarantee.

10. Appliances that are easy to transport may be delivered or sent to the consumer services department.

Home repairs are only anticipated for bulky appliances or built-in appliances.

11. If the appliances are built-in, built-under, fixed or suspended in such a way that removing and replacing

them in the place where they are fitted takes more than half an hour, the costs that result therefrom will

be charged for. Connected damage caused by these removal and replacement operations will be the

responsibility of the user.

12. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if the repair

costs are considered disproportionate, in agreement with the consumer, the defective appliance may

be replaced with another appliance of the same value.

In this event, we reserve the right to ask for a financial contribution calculated according to the length of

time it has been used.

20

13. A repair under guarantee does not mean that the normal guarantee period will be extended nor that a

new guarantee period begins.

14. We give a twelve month guarantee for repairs, limited to the same defect.

15. Except in the event where liability is legally imposed, this declaration of guarantee terms excludes any

compensation for damage outside the appliance for which the consumer wishes to assert his rights. In

the event of legally admitted liability, compensation will not exceed the purchase price paid for the

appliance.

These guarantee terms are only valid for appliances purchased and used in Belgium. For exported appliances,

the user must first make sure that they satisfy the technical conditions (e.g.: voltage, frequency, installation instruc-

tions, etc.) for the country concerned and that they can withstand the local climatic and environmental conditions.

For appliances purchased abroad, the user must first ensure that they meet the qualifications required in Belgium.

Non-essential or requested adjustments are not covered by the guarantee and are not possible in all cases.

Our consumer services department is always at your disposal, even after the guarantee period has expired.

Address for our consumer services department:

BELGIUM

Tel: Fax:

Electrolux Home Products Belgium Consumer services 02/363.04.44 02/363.04.00

ELECTROLUX SERVICE 02/363.04.60

Bergensesteenweg 719

1502 Lembeek

E-mail: [email protected]

GRAND-DUCHÉ DE LUXEMBOURG

ELECTROLUX HOME PRODUCTS Consumer services 00 35242431-1 0035242 431-360

Rue de Bitbourg. 7

L-1273 Luxembourg-Hamm

E-mail: [email protected]

21

This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for

the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to

another of the countries listed below the appliance guarantee will move with you subject to the following qualifica-

tions:

• The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by

production of a valid purchase document issued by the seller of the appliance.

• The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your

new country of residence for this particular model or range of appliances.

• The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to

another user.

• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within

the home, i.e. is not used for commercial purposes.

• The appliance is installed in accordance with all relevant regulations in force within your new country of

residence.

The provisions of this European Guarantee do not affect any of the rights granted to you by law.

European Guarantee

Page is loading ...

ZANKER ZKF680ITXB User manual

ZANKER ZKF680ITXB User manual

in other languages

Related papers

Other documents