Flymo HT450 User manual

Brand: Flymo

Model: HT450

Type: User manual

IMPORTANT INFORMATION

Read before use

& retain for future reference

For all customer enquiries or for replacement parts, contact:-

☎☎

01325 300303

www.flymo.com

eop.customer.services@electrolux.co.uk

HT42/420 HT45/450

HT51/510 HT60/600

Carton Contents

IMPORT

ANT !

Please check the contents of the carton are correct BEFORE assembling your new product.

IF ANY P

ARTS ARE MISSING CONTACT:-

Electrolux Outdoor Products Customer Service Department direct

Telephone : 01325 300303

Fax : 01325 318193

Safety

If not used properly this Hedgetrimmer can be dangerous! This Hedgetrimmer can cause

serious injury to the operator and others, the warnings and safety instructions must be fol-

lowed to ensure reasonable safety and efficiency in using this Hedgetrimmer. The opera-

tor is responsible for following the warning and safety instructions in this manual and on

the Hedgetrimmer.

Explanation of Symbols on your product

Warning.

Read the user instructions carefully to

make sure you understand all the con-

trols and what they do.

Switch off! Remove plug from mains

before adjusting, cleaning or if cable is

entangled or damaged. Keep the

cable away from the blade.

Do not use in the rain or leave the

Hedgetrimmer outdoors while raining.

The use of eye protection is recom-

mended.

instruction

manual

Switch levers

blade cover/storage holder

Handguard

General

1. Never allow children or people unfamiliar

with these instructions to use the

Hedgetrimmer. Local regulations may

restrict the age of the operator.

2. Only use the Hedgetrimmer in the manner

and for the functions described in these

instructions.

3. Never operate the Hedgetrimmer when you

are tired, ill or under the influence of alcohol,

drugs or medicine.

4. The operator or user is responsible for acci-

dents or hazards occurring to other people

or their property.

Electrical

1. The British Standards Institute recommend

the use of a Residual Current Device (R.C.D.)

with a tripping current of not more than 30mA.

Even with a R.C.D. installed 100% safety

cannot be guaranteed and safe working prac-

tice must be followed at all times. Check your

R.C.D. every time you use it.

2. Before use, examine cable for damage,

replace it if there are signs of damage or

ageing.

3. Do not use the Hedgetrimmer if the electric

cables are damaged or worn.

4. Immediately disconnect from the mains elec-

tricity supply if the cable is cut, or the insula-

tion is damaged. Do not touch the electric

cable until the electrical supply has been dis-

connected. Do not repair a cut or damaged

cable. Replace it with a new one.

5. Your electric cable must be uncoiled, coiled

cables can overheat and reduce the efficien-

cy of your Hedgetrimmer.

6. Keep cable away from the cutting area.

7. Never carry the product by the cable.

8. Never pull on the cable to disconnect any of

the plugs

9. Do not pull cable around sharp objects.

10. Always switch off at the mains before dis-

connecting any plug, cable connector or

extension cable.

11. Switch off, remove plug from mains and

examine electric supply cable for damage or

ageing befor

e winding cable for storage. Do

not repair a damaged cable, replace it with a

new one. Use only Electrolux Outdoor

Products replacement cable.

12. Always wind cable carefully, avoiding kink-

ing.

13. Use only on AC mains supply voltage shown

on the product rating label.

14. Our products are double insulated to

EN60335. Under no circumstances should

an earth be connected to any part of the

product.

Preparation

1. Always wear suitable clothing, gloves, and

stout shoes. The use of safety glasses is rec-

ommended. Do not wear loose clothing or

jewellery which can be caught in moving parts.

2. Thoroughly inspect the area where the

Hedgetrimmer is to be used and remove all

wires and other foreign objects.

3. Before using the machine and after any

impact, check for signs of wear or damage

and repair as necessary.

4. Never attempt to use an incomplete

Hedgetrimmer or one with an unauthorised

modification.

Use

1. Use the Hedgetrimmer only in daylight or

good artificial light.

2. Avoid operating your Hedgetrimmer on a

wet hedge, where feasible.

3. Know how to stop the Hedgetrimmer quickly

in an emergency.

4. Never hold the Hedgetrimmer by the guard.

5. Never operate the Hedgetrimmer with dam-

aged guards or without guards in place.

6. Remove plug from mains befor

e passing

Hedgetrimmer to another person.

7. Avoid operating while people especially chil-

dren are nearby.

8. Whilst using the Hedgetrimmer always be

sure of a safe and secure operating position.

9. Keep hands and feet away from the cutting

means at all times and especially when

switching on the motor.

10. Do not use stepladders whilst operating the

Hedgetrimmer.

11. Remove the plug from the mains :-

- before leaving the Hedgetrimmer unattended

for any period;

- before clearing a blockage;

- before checking, cleaning or working on the

appliance;

- if you hit an object. Do not use your

Hedgetrimmer until you are sure that the

entire Hedgetrimmer is in a safe operating

condition;

- if the Hedgetrimmer starts to vibrate abnor-

mally. Check immediately. Excessive vibra-

tion can cause injury.

- before passing to another person.

Maintenance and storage

1. Keep all nuts, bolts and screws secure to be

sure the Hedgetrimmer is in safe working

condition.

2. Replace worn or damaged parts for safety.

3. Be careful during adjustment of the

Hedgetrimmer to prevent entrapment of the

fingers between moving blades and fixed

parts of the machine.

4. After use the Hedgetrimmer should be

stored using the blade cover/storage holder

provided.

CABLES

IMPORTANT

• Use only 1.00mm

size cable up to 40 metres

length maximum.

Maximum rating :

1.00mm

size cable, 10 amps 250 volts AC.

• YOUR HEDGETRIMMER IS SUPPLIED

WITH CABLE WIRED DIRECTLY INTO THE

PRODUCT.

1. Mains Cables and Extension Cables are avail-

able from your local Electrolux Outdoor

Products Approved Service Centre.

2. Do not wire an extension cable directly to your

product yourself. Please contact your local

Electrolux Outdoor Products Approved Service

Centre for further information on the connec-

tors and kits available.

3. Only use extension cables specifically

designed for outdoor use.

CONNECTORS

IMPORTANT

• Connectors are suitable for use with 2 core

cable only. Under no circumstances should

these connectors be used for earthed prod-

ucts.

• All connectors and cables are of splashproof

construction. They are not waterproof and

must not be left outside permanently nor

should they be submerged or immersed in

water. Do not let cable lay or trail through

pools of water or splashed with water from

hose pipes.

MAINS PLUG REPLACEMENT

IMPORTANT

• If the plug supplied is cut off it should be

destroyed. There is an electric shock haz-

ard if a cut off plug is inserted into a 13

amp socket.

1. No earth required. Our products are double

insulated to EN60335 and under no circum-

stances should an earth be connected to any

part of the product.

2. Ensure the mains voltage suits your product

3. IMPORTANT!

The wires in the mains lead are coloured in

accordance with the following code:

BLUE - NEUTRAL

BROWN - LIVE

The wire which is coloured BLUE must be

connected to the Terminal which is marked

with the letter 'N' or coloured BLACK.

The wire which is coloured BROWN must be

connected to the Terminal which is marked

with the letter 'L' or coloured RED.

4. It is important that the outer sheath is clamped

correctly into the 3-pin plug.

5. If in doubt consult your local Service Repairer

or qualified electrician before the machine is

used.

6. A 13 Amp fuse must be fitted to the Mains

Plug.

7. The normal plug fuse and household fuse only

protect the electrical equipment and are not a

safeguard against electrocution.

BLACK

BLUE

RED

BROWN

If your product is hard wired i.e. non-

detachable mains electric cable, a conver-

sion kit and extension cable is available

from all Electrolux Outdoor Products

Approved Service Centres which can be

found in your local Yellow Pages.

Assembly of Handguard.

1. Insert Handguard into slot as illustrated in

figure A, ensuring that it is securely locat-

ed.

DO NOT USE THE PRODUCT WITH

OUT FITTING THE HANDGUARD

Assembly

Before starting your Hedgetrimmer.

1. Form a loop in mains cable and push the

loop through the hole in the handle as

illustrated in Fig. B.

2. To secure, position the loop over the hook

and pull back as illustrated in Fig. C.

3. Connect to mains and switch on

4. Remove blade cover/storage holder as

illustrated in Fig. D.

To start your Hedgetrimmer

1. There are two switch levers fitted to your

Hedgetrimmer.

2. Both switch levers need to be held in the

operating position (See Fig E) for the

product to start.

To stop your Hedgetrimmer

• Move Hedgetrimmer away from cutting

area before stopping.

1. To stop, release one

of the switch

levers.(Fig F)

Starting and Stopping

B C

How to Use

How to Use your Hedgetrimmer

1. Inspect area to be cut before each use -

remove objects which can be thrown or

become entangled in the cutting blades.

2. Always keep the Hedgetrimmer in front of your

body. Hold handle firmly with both hands and

stand in a secure and stable position.

3. Allow the cutting blades to reach full speed

before entering the material to be cut.

4. Always work going away from people and solid objects

such as walls, large stones, trees, vehicles etc.

5. If blade stalls, immediately stop the

Hedgetrimmer. Disconnect the Hedgetrimmer

from the power source and clear jammed

debris from the cutting blades. Inspect blades

and repair or replace as needed.

Top Cutting

Use a wide sweeping motion. See Fig. G. A

slight downward tilt of the cutting blades in the

direction of motion gives the best cutting results.

Side Cutting

When trimming the sides of the hedge, begin at the

bottom and cut upwards (See Fig. H), tapering the

hedge inward at the top. This shape will expose more

of the hedge, resulting in more uniformed growth.

Caring for your Hedgetrimmer

Cleaning (J)

1. Using a soft brush - remove debris from all

air intakes and cutting blade.

2. Wipe over surface of your hedgetrimmer

with a dry cloth.

• IMPORTANT

Never use water for cleaning your hed-

getrimmer. Do not clean with chemicals,

including petrol, or solvents - some can

destroy critical plastic parts.

Lubricating the Cutting Blade

For easier operation and longer life, lubricate

the cutter blades before and after use. Apply

the oil so that it runs between the two blades.

See Pic K.

At the end of the Cutting Season.

1. Clean your Hedgetrimmer thoroughly.

2. Check that all nuts and bolts are secure.

3. Visually inspect the Hedgetrimmer for any

worn or damaged parts, contact your local

Service Centre if any parts require

replacement.

To store your Hedgetrimmer

• The Hedgetrimmer blade cover/storage

holder is provided with 2 hanging slots for

storing the Hedgetrimmer on the wall.(See

Pic L)

• Ensure the blade cover/storage holder is

fitted before storage.

1. The use of 2 number 10 screws (40mm in

length) and the appropriate wall fixing

plugs is recommended

2. Drill 2 holes 47mm horizontally apart.

3. Fit wall plugs.

4. Fit screw ensuring enough length is avail-

able for secure location into hanging slot.

• Your mains cable can be stored with the

blade cover/storage holder fitted. (Pic M &

• Store in a dry place where your

Hedgetrimmer is protected from damage.

Fault Finding Hints

Fails to Operate

1. Is the Power Turned On?

2. Check the fuse in the plug, if blown replace.

3. Fuse continues to blow?

Immediately disconnect from the mains

electricity supply and consult your local

approved Service Centre.

Cutting blade stops under load

1. Cut at a slower pace.

2. If cutting blade still stops under load?

Disconnect from the mains electricity sup-

ply and consult your local approved

Service Centre.

Fails to stop when one switch lever is released.

Immediately disconnect from the mains

electricity supply and consult your local

approved Service Centre.

Poor cut quality

1. Ensure the product is being used correctly

(see How to Use)

2. Ensure blades are free from trapped debris

3. Damaged Blades?

Immediately disconnect from the mains

electricity supply and consult your local

approved Service Centre.

Excessive Vibration

Immediately disconnect from the mains

electricity supply and consult your local

approved Service Centre.

Electrolux Outdoor Products are manufactured

under an Environmental Management System (ISO

14001) using, where practical, components manu-

factured in the most environmentally responsible

manner, according to company procedures, and

with the potential for recycling at the end of the

products’ life.

• Packaging is recyclable and plastic compo-

nents have been labelled (where practical) for

categorised recycling.

• Awareness of the environment must be considered

when disposing of ‘end-of-life’ product.

• If necessary, contact your local authority for

disposal information.

The symbol on the product or on its packag-

ing indicates that this product may not be treated

as household waste. Instead it shall be handed

over to the applicable collection point for the

recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly,

you will help prevent potential negative conse-

quences for the environment and human health,

which could otherwise be caused by inappropri-

ate waste handling of this product.

For more detailed information about recycling of

this product, please contact your local council

office, your household waste disposal service or

the shop where you purchased the product.

If any part is found to be defective due to faulty

manufacture within the guarantee period, Electrolux

Outdoor Products, through its Authorised Service

Repairers will effect the repair or replacement to the

customer free of charge providing:

(a) The fault is reported directly to the Authorised Repairer.

(b) Proof of purchase is provided.

faulty adjustment by the user.

(d) The failure has not occurred through fair wear and tear.

(e) The machine has not been serviced or repaired,

taken apart or tampered with by any person not

authorised by Electrolux Outdoor Products.

(f) The machine has not been used for hire.

(g) The machine is owned by the original purchaser.

(h) The machine has not been used outside of the

country for which it was specified.

(i) The machine has not been used commercially.

* This guarantee is additional to, and in no way

diminishes the customers statutory rights.

Failures due to the following are not covered, there-

fore it is important that you read the instructions con-

tained in this Operator's Manual and understand how

to operate and maintain your machine:

Failures not covered by guarantee

* Replacing worn or damaged blades

* Failures as a result of not reporting an initial fault.

* Failures as a result of sudden impact.

* Failures as a result of not using the product in

accordance with the instructions and recommen-

dations contained in this Operator's Manual.

* Machines used for hire are not covered by this guar-

antee.

* The following items listed are considered as

wearing parts and their life is dependent on regu-

lar maintenance and are, therefore not normally

subject to a valid warranty claim: Blades, Electric

Mains cable.

* Caution!

Electrolux Outdoor Products does not accept lia-

bility under the warranty for defects caused in

whole or part, directly or indirectly by the fitting of

replacement parts or additional parts that are not

either manufactured or approved by Electrolux

Outdoor Products, or by the machine having

been modified in any way

Guarantee & Guarantee Policy

Environmental Information

5119561-02

Electrolux Outdoor Products

Aycliffe Industrial Park

NEWTON AYCLIFFE

Co.Durham DL5 6UP

ENGLAND

Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339

Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.

Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and

trademarks in several countries.

Registered number 974979 England

The Electrolux Group. The world’s No.1 choice.

The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million

Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold

each year to a value of approx. USD 14 billion in more than 150 countries around the world.

Service Recommendations

I, the undersigned M. Bowden of Electrolux

Outdoor Products, Aycliffe Industrial Park,

NEWTON AYCLIFFE, Co. Durham. DL5

6UP. Certify that the product:-

Category........ Hedgetrimmer

Make.............. Electrolux Outdoor

Products

Conforms to the specifications of Directive

2000/14/EEC

I, the undersigned M. Bowden of Electrolux

Outdoor Products, Aycliffe Industrial Park,

NEWTON AYCLIFFE, Co. Durham. DL5

6UP Certify that a sample of the above

product has been tested using directive

81/1051/EEC as a guide. The maximum A-

weighted sound pressure level recorded at

operator position under free field semi ane-

choic chamber conditions was :-

I, the undersigned M. Bowden of Electrolux

Outdoor Products, Aycliffe Industrial Park,

NEWTON AYCLIFFE, Co. Durham. DL5

6UP Certify that a sample of the above

product has been tested using ISO 5349 as

a guide. The maximum weighted root mean

square value of vibration recorded at opera-

tor’s hand position was:-

Newton Aycliffe, 16/08/2004

M. Bowden,

Research & Development Director

1. We strongly recommend that your product

is serviced at least every twelve months,

more often in a professional application.

2. Always use genuine Electrolux Spare Parts.

3. Prepacked spares are available from most

Electrolux Outdoor Products stockists.

4. Your product is uniquely identified by a sil-

ver and black product rating label

5. If you have a problem with your machine

contact your local Approved Service Centre

ensuring you have full details of your product

as described on the product rating label.

6. Should it be necessary for work to be carried

out by your Service Centre, it is important to

take your complete machine including cable

and any extension cables used.

A network of specialist dealers can be found in

your local Yellow Pages. To obtain service on

your product simply telephone or visit your local

Service Centre. Should you require service

under the terms of our guarantee the Service

Centre will require proof of purchase.

All of the centres listed stock genuine

Electrolux Spare Parts.

NOTE: Our Service Repairers act on their own

behalf and are not empowered to commit or

legally bind Electrolux Outdoor Products in

any manner whatsoever.

Declaration of Conformity

Type............................................... HT42/HT420 HT45/HT450 HT51/HT510 HT60/HT600

Blade Length................................. 42cm 45cm 51cm 60cm

Guaranteed sound power level.. 101 dB (A) 105 dB (A) 101 dB (A) 101 dB (A)

Measured Sound Power Level...98 dB (A) 97 dB (A) 98 dB (A) 98 dB (A)

Level............................................... 90 dB (A) 91 dB (A) 95 dB (A) 95 dB (A)

Value.............................................. 4.04 m/s

4.6 m/s

7.5 m/s

Weight............................................ 3.2 Kg 3.2 kg 3.5 kg 3.5 kg

Identification of Series......See Product Rating Label

Conformity Assessment Procedure....ANNEX VI

Notified Body.................... I.T.S., Cleeve Road, Leatherhead,

Surrey. KT22 7SB England

Other Directives:-............. 98/37/EEC, 89/336/EEC,

73/23/EEC

& applicable standards:-. EN61000-3-2, EN61000-3-3,

EN55014-1, EN55014-2, EN774, EN50144-1,

EN50144-2-15

Flymo HT450 User manual

Flymo HT450 User manual

Related papers

Other documents