Craftsman 48"MOWER 917.24985 User manual

Brand: Craftsman

Model: 48"MOWER 917.24985

Category: Tractor

Type: User manual

This manual is also suitable for

Owner's Manual

GRASS CATCHER

Model No.

917.249850

CAUTION:

Read and follow all Safety

Rules and Instructions be-

fore operating this equip-

ment.

• Safety

• Assembly

• Operation

• Customer Responsibilities

• Repair Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Visit our Craftsman website:www.sears.com/craftsman

SAFETY RULES

Safe Operation Practices for Ride-On Mowers _J_

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE

TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

I. GENERAL OPERATION

Read, understand, and follow all instructions in the manual

and on the machine before starting.

Only allow responsible adults, who are familiar with the

instructions, to operate the machine.

Clear the area of objects such as rocks, toys, wire, etc.,

which could be picked up and thrown by the blade.

Be sure the area is clear of other people before mowing.

Stop machine if anyone enters the area.

Never carry passengers.

Do not mow in reverse unless absolutely necessary. Always

look down and behind before and while backing.

Be aware of the mower discharge direction and do not point

it at anyone. Do not operate the mower without either the

entire grass catcher or the guard in place.

Slow down before turning.

Never leave a running machine unattended. Always turn

off blades, set parking brake, stop engine, and remove keys

before dismounting.

Turn off blades when not mowing.

Stop engine before removing grass catcher or unclogging

chute.

Mow only in daylight or good artificial light.

Do not operate the machine while under the influence of

alcohol or drugs.

Watch for traffic when operating near or crossing

roadways.

Use extra care when loading or unloading the machine into

a trailer or truck.

Data indicates that operators, age 60 years and above,

are involved in a large percentage of riding mower-related

injuries. These operators should evaluate their ability to

operate the dding mower safelyenough to protect themselves

and others from serious injury.

Keep machine free of grass, leaves or other debris build-up

which can touch hot exhaust / engine parts and burn. Do not

allow the mower deck to plow leaves or other debris which

can cause build-up to occur. Clean any oil or fuel spillage

before operating or storing the machine. Allow machine to

cool before storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tipover

accidents, which can resultin severe injury or death. All slopes

require extra caution. If you cannot back up the slope or ifyou

feel uneasy on it, do not mow it.

DO:

• Mow up and down slopes, notacross.

Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven terrain could

overturn the machine. Tallgrass can hide obstacles.

• Use slow speed. Choose a low gear so that you will not

have to stop or shift while on the slope.

• Follow the manufacturer's recommendations for wheel

weights or counterweights to improve stability.

Use extra care with grass catchers or other attachments.

These can change the stability of the machine.

Keep all movement on the slopes s/owand gradual. Do not

make sudden changes in speed or direction.

Avoid starting or stopping on a slope. If tires lose traction,

disengage the blades and proceed slowly straightdown the

slope.

DO NOT:

Do not turn on slopes unless necessary, and then, turn slowly

and gradually downhill, if possible.

Do not mow near drop-offs, ditches, or embankments. The

mower could suddenly turn over if a wheel is over the edge

of a cliff or ditch, or if an edge caves in.

Do not mow on wet grass. Reduced traction could cause

sliding.

Do not try to stabilize the machine by putting your foot on

the ground.

Do not use grass catcher on steep slopes.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

Keep children out of the mowing area and under the watchful

care of another responsible adult.

Be alert and turn machine off if children enter the area.

Before and when backing, look behind and down for small

children.

Never carry children. They may fall off and be seriously

injured or interfere with safe machine operation.

Never allow children to operate the machine.

Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

IV. SERVICE

Use extra care in handling gasoline and other fuels. They

are flammable and vapors are explosive.

Use only an approved container.

Never remove gas cap oradd fuel withthe enginerunning.

Allow engine to cool before refueling. Do not smoke.

Never refuel the machine indoors.

Never store the machine or fuel container inside where

there is an open flame, such as a water heater.

Never run a machine inside a closed area.

Keep nutsand bolts,especially blade attachment bolts, tight

and keep equipment in good condition.

Never tamperwith safety devices.Checktheir properoperation

regularly.

Keep machine free of grass, leaves, or other debris build-

up. Clean oil or fuel spillage. Allow machine to cool before

storing.

Stopand inspectthe equipment if you strikean object. Repair,

if necessary, before restarting.

Never make adjustments or repairs with the engine

running.

Grass catcher components are subject to wear, damage,

and deterioration, which could expose moving parts or

allow objects to be thrown. Frequently check components

and replace with reanufacturer"srecommended parts, when

necessary.

Mower blades are sharp and can cut. Wrap the blade(s) or

wear gloves, and use extra caution when servicing them.

Check brake operation frequently. Adjust and service as

required.

SAFETY RULES

_lb Safe Operation Practices for Ride-On Mowers &

Be sure the area is clear of other people before mowing.

Stop machine if anyone enters the area.

Never carry passengers or children even with the blades

off.

Do not mow in reverse unless absolutely necessary. Always

look down and behind before and while backing.

Never carry children. They may fall off and be seriously

injured or interfere with safe machine operation.

Keep children out of the mowing area and under the watchful

care of another responsible adult.

Be alert and turn machine off if children enter the area.

Before and when backing, look behind and down for small

children.

Mow up and down slopes (15° Max), not across.

Remove obstacles such as rocks, tree limbs, etc.

Watch forholes, ruts, orbumps. Uneven terrain couldoverturn

the machine. Tall grass can hide obstacles.

Use slow speed. Choose a low gear so that you will not

have to stop or shift while on the slope.

Avoid starting or stopping on a slope. If tires lose traction,

disengage the blades and proceed slowly straight down the

slope.

If machine stops while going uphill,disengage blades, shift

into reverse and back down slowly.

Do not turn on slopes unless necessary, and then, turn

slowly and gradually downhill, if possible.

Look for this symbol to point out |

important safety precautions. It means

CAUTION!!! BECOME ALERT!!! YOUR

SAFETY IS INVOLVED.

_1 CAUTION: Do not coast down a hill

in neutral, you may lose control of

the tractor.

CAUTION: Tow only the attachments

that are recommended by and

comply with specifications of

the manufacturer of your tractor.

Use common sense when towing.

Operate only at the lowest possible

speed when on a slope. Too heavy

of a load, while on a slope, is

dangerous. Tires can lose traction

with the ground and cause you to

lose control of your tractor.

CAUTION: In order to prevent

accidental starting when setting

up,transporting,adjusting or making

repairs, always disconnect spark

plug wire and place wire where it

cannot contact spark plug.

CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, engineered and manufactured to

give you the best possible dependability and performance.

Should you experience any problems you cannot easily remedy, please contact your nearest authorized service center/

department. They have competent, well trained technicians and the proper toolsto service or repair this unit.

Please read and retain this manual. The instructionswillenable you to assemble and maintain your Grass Catcher properly.

Always observe the "SAFETY RULES".

SAFETY RULES ......................................................... 2-3

ASSEMBLY ................................................................. 5-7

OPERATION .................................................................. 8

CUSTOMER RESPONSIBILITIES ................................. 9

STORAGE ...................................................................... 9

WARRANTY ................................................................... 9

REPAIR PARTS....................................................... 10-11

KNOW YOUR GRASS CATCHER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATINGYOU RGRASS CATCH ER.

Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study

the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to

prevent injury to yourself and others. Save this manual for future reference.

The operation of any tractor can result in foreign objects thrown into the eyes,

which can result in severe eye damage. Always wear safety glasses or eye shields

before starting your tractor and while mowing. We recommend a wide vision safety

mask for over the spectacles or standard safety glasses.

UNPACKING INSTRUCTIONS

Remove all parts and packing materials from carton.

• Check carton contents against list. Be sure all parts

are there.

CARTON CONTENTS:

(3) Container Tops

(3) Container Bottoms

(1) Upper Chute

(1) Lower Chute

(1) Support Assembly

(1) Cover Assembly

(2) Shoulder Bolts

(1) Retainer Spring

TOOLS REQUIRED FOR ASSEMBLY

(1) 9/16" Wrench

SUPPORT

ASSEMBLY

PARTS IDENTIFICATION RETAINER

SPRING _

COVER

ASSEMBLY

SHOULDER

BOLTS

FULL

BAGGER

INDICATOR

CHUTE LATCH

UPPER CHUTE

GRASS

CATCHER

CONTAINERS

LOWER CHUTE

ATrACHING

STRAPS

NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the

tractor, in the operator's position.

CAUTION: BEFORE ASSEMBLING GRASS CATCHERTOTRACTOR:

_ Depress clutch/brake pedal fully and set parking brake.

Place gearshift/motion control lever in "NEUTRAL" position.

Place attachment clutch in "DISENGAGED" position.

Turn ignition key "OFF" and remove key.

• Make sure the blade and all moving parts have completely stopped.

• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact

with plug,

BAGGER SUPPORT ASSEMBLY

(See Figs. 1A & 1B)

Remove and discard the upper bolt on both sides of

the drawbar. Using the same holes, install the shoulder

bolts supplied and tighten securely.

REMOVE AND DISCARD

UPPER BOLTS ANDINSTALL

SHOULDER BO_SSUPPLIED

DRAWBAR

FIG, 1A

2. Align support assembly pin with hole in drawbar and

hang assembly over the shoulder bolts.

3. Be sure support assembly isseated properly and secure

with retainer spring supplied.

SHOULDER

BOLTS

SUPPORT

ASSEMBLY

RETAINER

SPRING _d _.I °

FIG. 1B

MOUNTING COVER ASSEMBLY TO

SUPPORT ASSEMBLY (See Fig. 2)

NOTE: For ease of assembly, you may wish to obtain the

assistance ofanother person formountingcover assembly

to tractor.

1. Position cover assembly on ground behind tractor as

shown.

2. Lift and rotate cover to align cover brackets with support

assembly tubes.

3. Slide cover assembly down onto the support tubes.

COVER

SUPPORT

ASSEMBLY

02532

FIG. 2

CONTAINER ASSEMBLY (See Fig. 3)

1. Place bottom half inside of top half, as shown.

2. Place one foot inside bottom half and lift top half to

meet bottom half.

3. Press halves tightly together while lifting top to lock

into place as shown.

IMPORTANT:BEFORE LOCKINGTHETABS, HOOKED EDGES

ONBOTHHALVESMUSTOVERLAPTOFORMSEALASSHOWN

IN INSET.

4. Repeat for other containers.

CONTAINER

BOTTOM HALF

CONTAINER

TOP HALF

PRESS TOGETHER

TO FORM SEAL

CONTAINER WHILE LIFTING

TOP HALF TOP HALF

CONTAINER

BOTTOM

HALF

LOCKING

TAB

FIG. 3

ASSEMBLY CHECK: Squeeze sides of lower half of con-

tainer and check that there is no gap between upper and

lower halves. If a gap appears, unlock tabs to separate

container halves and repeat instructions above.

CONTAINER MOUNTING (See Fig. 4)

1. Install one container to left side first with warning to

outside of unit. Install another container to center

position and one in right position.

NOTE: Right container should always overlap left container

at center supports.

2. Close cover and lock latch handles over center support

tubes.

COVER LATCH

HANDLES

CONTAINER

WARNING

TUBES

CONTAINER

HANDLE

CONTAINER

WARNING

LOWER CHUTE (See Fig. 5)

1. Raise and hold deflector shield in upright position.

2. Place slot in lower chute over tab on mower deck and

position lower chute over deck opening as shown.

3. Hook rear latch into flange hole on back of mower

deck.

4. Hook front latch into tab hole on front of mower deck.

CAUTION: Do not remove deflector

shield from mower. Raise and hold

shield when attaching lower chute

and allow it to rest on chute while in

operation.

TAB

DEFLECTOR

SHIELD

OP_ONALFRONT

GAUGEWHEEL

FRONT

LATCH

;EAR LATCH

FIG. 5

UPPER CHUTE (See Figs. 6A & 6B)

1. Lower mower deck to its lowest cutting position.

2. Assemble upper chute by inserting curved end into

hole in back of cover.

NOTE: Handle carefully so as not to damage full bagger

indicator.

3. Push inand turn upper chute until itis in line with lower

chute.

4. Align the bosses on lower chute with alignment slots

on upper chute and slide together.

5. Secure with rubber latch by hooking hole in latch over

latch pin.

COVER

FULL BAGGER

UPPER INDICATOR HANDLE

CHUTE

LOWER

CHUTE

FIG. 6A

ALIGNMENT

SLOT

_ / LATCH PIN

FIG. 6B

LEVEL MOWER DECK

Besuredeck isproperlyleveledforbestmower performance.

See your tractors owner's manual for instructions.

TIPS FOR IMPROVED BAGGING

OPERATION:

Follow the mower operation instructions in your tractor

owner's manual.

When operating your grass catcher on a lawn where grass

and leaf bagging equipment has not been used, you are

picking up thatch and debris that has accumulated for tong

periods of time. The amount collected and the total time

of operation may be greater than you will experience with

regular use of your grass catcher.

Always run throttle at full speed when bagging.

• Select a gear low enough to give good mower cutting

performance, good quality cut and good bagging

performance.

NOTE: it may be necessary to overlap width of cut to suit

your conditions.

• If grass isextremely tall, it should be mowed twice.The

first time relatively high, the second time to desired

height.

• Use left hand side of mower for trimming.

• Plastic trash bags can be inserted inside grass catcher

containers for ease of debris disposal. To remove the

plastic trash bags when full:

a. Disengage blades, shift into neutral, engage the

parking brake and stop the engine.

b. Raise seat. Unlatch and raise cover.

c. Remove one container at a time by grasping

container handles and pulling toward the rear, off

of the tube rails.

d. With the container resting on the ground, close

and secure the top of the plastic lawn bag.

e. Tip the container on itsside and slide the filled bag

from the container.

f. Install a new plastic lawn bag with the edges of the

bag draped over upper lip of the container.

g. Repeat for other containers.

h. Reinstall containers making sure right container

overlaps left container at center supports.

j. Close cover and secure latches over center support

tubes.

Avoid cutting wet grass or inthe morning while the dew

is still heavy, Grass clippings collected under these

conditions tend to be sticky and adhere to the walls of

the flow path causing clogging.

Your bagger is equipped with a full bagger indicator.

Movement of the wheel increases as the bags fill.The

wheel will be spinning fastest just before the bags fill

completely. When the wheel stops, it indicates that the

bags are full and the chutes have become clogged.

NOTE: To help prevent clogging of chutes, check/empty

bags when the wheel isspinning fast. Experience will teach

you the best time to empty the bags.

Care should be taken not to damage the parts and that

the wheel spins freely at the beginning of each use.

• If the grass catcher fails to pick up cut grass or leaves,

it is an indication that clogging has occurred in the

system or that the grass catcher containers are full.

Usually this is indicated by the stopped movement of

the full bagger indicator.

a. Disengage blades, shift into neutral, engage the

parking brake and stop the engine.

- Raise seat. Unlatch and raise cover.

- Slide out containers and dispose of clippings.

- Replace containers, close cover, and latch.

Unlatch chutes and check for clogging.

- Remove all debris in chutes.

- Reassemble and latch chutes

Check toinsure fullbagger indicator has notbecome

clogged.

- The air passage hole must be clear of debris.

Gently insert a small twig or wire into passageway

to clear.

b CAUTION

• Do not operate mower with grass catcher

partially installed.

• Disengage blades and stop engine before

leaving tractor seat to empty containers,

unclogging chutes, etc.

• Close cover before starting.

• Disengage mower when crossing driveways

or gravel surfaces and other areas where

thrown objects could be a hazard.

• Do not attempt to vacuum up cans or other

potentially hazardous projectiles.

GENERAL RECOMMENDATIONS

Always observe safety rules when performing any main-

tenance.

Before each use check for loose fasteners.

Clean unit thoroughlyafter each use.

BLADE CARE

Forbest resultsmowerbladesmustbe kept sharp. Replace

bent or damaged blades.

See BLADE CARE instructionsin yourtractor owner's

manual.

STORAGE

When gra_ catcher is to be stored for a period of time,

clean it th: ,-t::ghly,remove all dirt, grass, leaves, etc. Store

in a clean, _;y place.

CAUTION: Do not leave grass in bagger

containers. Empty containers aftereach

use and before storing. Failure to do so

may result in spontaneous combustion

which could develop into a fire.

CAUTION: BEFORE PERFORMING ANY

MAINTENANCE, SERVICE OR ADJUST-

MENTS:

• Depress clutch brake pedal fully and

set parking brake.

• Place gearshift/motion control lever in

"NEUTRAL" position.

• Place clutch control in "DISENGAGED"

position.

• Turn ignition key to "OFF" position.

• Make sure blades and all moving parts

have completely stopped.

• Disconnect spark plug wire(s) from

spark plug(s) and place wire where it

cannot come in contact with plug.

CAUTION: Grass catcher components

are subject to wear, damage and

deterioration, which could expose

moving parts or allow objects to be

thrown. Frequently check components

and replace with manufacturer's

recommended parts, when necessary.

LIMITED ONE YEAR WARRANTY ON

CRAFTSMAN GRASS CATCHER

For one year from the date of purchase, when this grass catcher attachment is maintained according to the oper-

ating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or

workmanship.

This warranty does not cover:

• Expendable items which become worn during normal use, such as bags or mower blades.

Repairs necessary because of operator abuse or negligence, including the failure to maintain the equipment

according to instructionscontained in the owner's manual.

Grass catcher attachments used for commercial or rental purposes.

Warranty service isavailable by returning the craftsman grass catcher to the nearest Sears parts and repair center

inthe United States. This Warranty applies only while this product is in use in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL. 60179

REPAIR PARTS

GRASS CATCHER - - MODEL NUMBER 917.249850

• 35

REPAIR PARTS

GRASS CATCHER - - MODEL NUMBER 917.249850

...= 10

-" 11

KEY PART

NO. NO.

2 69180

3 127533

4 139851

5 176741

6 18021008

7 130933

8 87175

19061216

7206J

STD541810

STD551110

109808X

2029J

130760

130759

174345

71161010

132796

140809

KEY PART

DESCRIPTION NO. NO.

Nut, Crownlock #10-24 23 132983

Screen, Cover 26 4939M

Cover Assembly (Includes 3, 37, 38, 39) 28 179534

Chute, Upper 29 176997

Screw, Special #10-14xl/2 30 165898

Full Bagger Indicator 31 174083

Screw, #10-24 x 1-1/8 32 176990

Washer 3/16x3/4x16 Ga. 33 128600

Spacer, Split 34 127534

Nut, Acorn #10-24 35 183286

Washer, lock #10 36 129586

Latch, Chute 37 134637

Nut, Weld 38 130895

Latch, Hook 39 186601

Rubber, Latch 40 71141008

Chute, Lower 46 74760536

Screw #10-24 x 5/8 Truss Head -- 177860

Spring, Cover L.H. (black)

Spacer, Cover

DESCRIPTION

Spring, Cover R.H. (gray)

Spring, Retainer

Support Assembly

Shoulder Bolt

Spring, Retainer

Plug, Tubing End

Bagger, Frame

Pin, Hinge

Gasket, Cover

Container, Top

Container, Bottom

Seal, Cover

Latch Handle, Cover

Strip, Reinforcement

Screw #10-24 x 1/2

Bolt, Hex 5/16-18 x 2-1/4

Owner's Manual

Get it fixed, at your home or ours!

Your Home

For repair - in your home - of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home apphances

and items like garage door openers and water heaters.

1-800-4-MY-HOME _ Anytime, day or night

(1-800-489-4663) (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in products like vacuums, lawn equipment,

and electronics, call or go on-line for the nearest

Sears Parts and Repair Center.

1-800-488-1222 Anytime,day or night (U.S.A only)

www.sears.com

To purchase a protection agreement (U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparaci6n

a domicilio, y para ordenarpiezas:

1-888-SU-HOGAR sM

(1-888-784-6427)

Au Canada pour serviceen franc,_is:

1-800-LE-FOYERMc

(1-800-533-6937)

www sears.ca

SEARS

® Registered Trademark / TM Trademark / SMService Mark of Sears, Roebuck and Co

® Marca Regtstrada / n¢Marca de F,_bnca / SMMarca de Servlc_o de Sears, Roebuck and Co

MCMarque de commerce / MDMarque d_posee de Sears, Roebuck and Co

177860 Rev 2 3.10.03 rad Printed in U.S.A.

Craftsman 48"MOWER 917.24985 User manual

Brand: Craftsman

Model: 48"MOWER 917.24985

Category: Tractor

Type: User manual

This manual is also suitable for

Download PDF

report

Craftsman 48"MOWER 917.24985 User manual

This manual is also suitable for

Craftsman 48"MOWER 917.24985 User manual

Related papers

Other documents