Miele PT 8301 SL Installation Diagram

PT 8301 SL
Miele
Brand
Miele
Model
PT 8301 SL
Category
Wire connectors
Type
Installation Diagram

This manual is also suitable for

02.11 M.-Nr. 09 108 920 / 01
Installation plan
Tumble dryers
Installatieschema
Droogautomaat
PT 8301 SL EL
PT 8301 COP SL EL
PT 8303 SL EL
nl - NL
en - GB
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Installationsplan / Installation plan: PT 8301/8303 SL
Datum / Date: 09.12.2010 Seite / Page: 7
Technical datasheet
Tumble dryer:
Heating:
PT 8301/8303 SL
Electric (EL)
Legend:
Abbreviations in bold type:
Connection required
en - GB
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Machine connections:
Electrical
connection
1. Standard voltage (as supplied)
V
3N AC 380 - 415
Frequency
Hz
50
Rated load
kW
14.2
Fuse rating
A
3 × 25
Connection cable, min. cross-section
mm²
5 × 4
Cable screw connector
M 32
Connection cable (to be ordered separately)
2. Standard voltage (as supplied)
V
3 AC 220 - 240
Frequency
Hz
50
Rated load
kW
14.2
Fuse rating
A
3 × 50
Connection cable, min. cross-section
mm²
4 × 10
Cable screw connector
M 40
Connection cable (to be ordered separately)
Electrical connection must comply with national regulations.
Connection using multi-pole wall socket in compliance with
IEC/EN 60309 and IEC/EN 60947 is recommended in order to
simplify electrical tests.
If machines are hard-wired, a multi-pole mains switch must be
provided on site.
A wall socket or mains isolator must be accessible after
installation.
Vented
Max. nominal air throughput in vented mode
m³/h
821
Max. permissible pressure loss
Pa
300
Connection on machine side (ext. diameter)
mm
150
Connection pipe provided on site (int. diameter)
mm
150
Max. temperature
°C
80
As relative humidity inside the vent ducting can be as high as
100%, suitable measures must be taken to prevent a
backflow of condensate into the machine.
Air intake
Standard connection: Air intake from installation site
Unobstructed air intake into room recommended (corres-
ponding to 3 times the vent cross-section of machine)
cm²
531
A sufficient supply of fresh air should be ensured to
replace the air extracted.
Alternative connection: Ducted air intake (from outside
building)
Connector on machine (int. diameter)
mm
161
Connection pipe provided on site (ext. diameter)
mm
160
Lid removal exposes live components! For safety reasons,
the pipe connected for central air intake should be at least
900 mm long and secured using two screws.
Installationsplan / Installation plan: PT 8301/8303 SL
Datum / Date: 09.12.2010 Seite / Page: 8
Fittings (supplied)
Without plinth
2 × clamps
2 × screws DIN 571 (Ø × length)
mm
6 × 40
2 × rawl plugs (Ø × length)
mm
10 × 50
The machine should be bolted to the floor.
Fixing materials for a floating screed floor are to be provided
on site.
Machine data
Unit width
mm
711
Machine depth
mm
1088
Unit height
mm
1800
Casing width
mm
708
Casing depth
mm
999
Minimum width of delivery access to installation site
mm
725
Recommended rear wall gap (measured to front of machine)
mm
1500
Min. wall gap (to rear edge of lid)
mm
500
Net weight
kg
139
Dynamic floor load, max.
N
1584
Average heat dissipation
(dependent on ambient room temperature and programme
selected)
W
473
A Noise level
dB (A)
68.9
A Sound pressure level
(measured at a distance of 1 m from the machine and at a
height of 1.6 m)1 m
dB (A)
56
Installation should only be carried out by authorised fitters in accordance with valid regulations!
Observe installation instructions when installing machine! All rights reserved! Measurements in mm.
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Miele PT 8301 SL Installation Diagram

PT 8301 SL
Miele
Brand
Miele
Model
PT 8301 SL
Category
Wire connectors
Type
Installation Diagram
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents