BLOTZ B28-MD-009 Assembly Instructions

Brand
BLOTZ
Model
B28-MD-009
Type
Assembly Instructions

This manual is also suitable for

28mm / 32mm Medieval Coaching Inn
B28-MD-009 / B32-MD-009
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember
to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while
you allow glue to dry.
You may find it easier to paint portions of this model BEFORE construction – please see the end of the document for info
about this.
Ground Floor
Remove the doors and their handles from the
sprue and glue them together as shown.
Take the wall sections shown above from the sprue.
Glue them to the floor with all the etched detail
facing inwards.
Each door should have 2 door supports.
Glue the lower support into the gap at the bottom
of the door as shown.
Place the top support on top of the door and gently
slide this into position.
Take the two blank walls and short ends from the
sprue.
Glue these into place which leaves the space for the
passageway.
Take the frames shown above. Starting with the
two doors, glue their frames into position. They
will aligh on the left and extend out by around
3mm on the right.
Work around the building, gluing each frame into
position, making sure the spaces for the windows
align correctly.
Now takes the frames for the other section.
And glue those into place as well.
Then take the insert sections from the sprue and
glue them into the spaces in the framework.
Note the insert pieces for each wall are in their
relative positions on the sprue.
Upper Floor
Take the upper walls and floor sections shown
above from the sprue.
Glue the long wall pieces into place on the square
floor section then add the side and low walls to it
before attaching the thin floor section and its side
and low walls.
Glue the upper floor section into position.
The frames for the upper floor.
Starting with the front wall, work around the
building in the same way you did the lower floor.
The frames added within the passage.
Go round the building adding the insert pieces
into the gaps in the frames the same way you did
the lower floor.
Roof
Take the roof sections and end supports from the
sprue.
Glue one of the roof pieces to the supports as
shown.
Glue the other roof piece into position.
We suggest you now paint your roof (see painting
tips below)
With the roof painted, add the roof plate.
Glue the framework pieces into the gaps at the
ends of the roof.
Then add the insert pieces.
The chimney is formed from the four pieces
shown above.
Glue them together to form a square tube.
Trim the lower front wall so it is flush with the
angle of the sides
Paint the chimney then stick it to the roof.
Painting
It is much easier to paint sections of this building prior to assembly.
For the inner walls we removed these from the sprue and then sprayed them white with a standard car undercoat spray
paint.
Once dry we then painted over the etched woodwork with a pale brown colour.
The stone floor was sprayed black, then dry-brushed with various grey colours (DIY Emulsion)
The outer frames remained unpainted.
The insert panels were all left on the sprue and sprayed with a standard white car undercoat.
The lower part of the inserts can either be done as brick or stone:
• If brick, then after the white undercoat has dried, drybrush with a terracotta colour (standard DIY emulsion paint).
• If stone, then once the upper portions of the inserts have been added to the model, the lower portions were then
resprayed with a black car undercoat before being dry brushed with 2 different shades of grey (DIY emulsion paint)
The roof was partially assembled – roof pieces glued to the end sections before spraying the entire roof with a black car
undercoat spray.
If slate, then drybrush with a dark grey colour, before dry-brushing with a lighter grey (DIY emulsion).
If pantile, then drybrush with a chocolate brown colour before dry-brushing with a red colour (DIY emulsion)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

BLOTZ B28-MD-009 Assembly Instructions

Brand
BLOTZ
Model
B28-MD-009
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers